共查询到20条相似文献，搜索用时 62 毫秒
1.
为了探究静压沉桩与CPTU贯入力学机制,开展了饱和黏土中静压沉桩及CPTU贯入的离心模型试验,获得了静压沉桩与CPTU贯入过程中土压力、超孔压和贯入阻力的变化规律。同时,将静压桩和CPTU压入过程视为一系列球孔的连续贯入,应用圆孔扩张解答,建立了静压沉桩和CPTU贯入过程中锥头阻力、侧阻力与超孔压的预测方法。通过离心模型试验和理论预测结果的对比分析表明：随着桩体的压入,桩周土体的超孔压和土压力均逐渐增大,当桩头通过监测点时,超孔压与土压力均达到最大值;在饱和黏土中,CPTU锥头阻力、锥侧摩阻力和锥头超孔压与锥头贯入深度总体上呈线性关系。预测方法估算沉桩和CPTU贯入引起的土压力、超孔压与模型试验结果相符,较好地反映了饱和黏土中静压沉桩和CPTU贯入的力学机制。 相似文献
2.
The piezocone penetration test (CPTU) is commonly used as a fast and economical tool to identify soil profile and to estimate relevant material properties in soils ranging from fine to coarse-grained. Moreover, in the case of fine-grained soils (clays and silts), the consolidation coefficient and the permeability can be estimated through the dissipation test. Undrained conditions are commonly assumed for the interpretation of CPTU in fine-grained soils, but in soils such as silts, penetration may occur in partially drained conditions. This aspect is often neglected in data interpretation thus leading to an inaccurate estimate of soil properties. This paper investigates numerically the effect of partial drainage during penetration on the measured tip resistance and the subsequent pore pressure dissipation response contributing to a more accurate interpretation of field data. A realistic simulation of the cone penetration is achieved with the two-phase Material Point Method, modelling the soil response with the modified Cam-Clay model. The approach takes into account large soil deformations induced by the advancing cone, soil–water, and soil–structure interactions, as well as nonlinear soil behavior. 相似文献
3.
南海迭层土物理力学特性的研究 总被引：1，自引：0，他引：1
我国海域普遍分布有迭层土,由于结构的特殊性,对于其性质的准确把握,直接影响到海洋工程诸如打桩、钻井船插深等问题预测的准确性,关系到海洋工程建设的安全。现场进行孔压静力触探CPTU试验以及室内试验,分析我国南海海域迭层土的物理、力学性质的特点,对迭层土抗剪强度值的确定进行探讨。CPTU试验数据显示,迭层土的物理力学性质与单一土层具有较明显的差异;由于迭层土中砂层的存在,室内三轴不排水剪切试验（UU试验）确定的不排水强度明显偏低,是CPTU确定的不排水抗剪强度的下限值。CPTU的结果可以较好地反映了迭层土的特点,根据CPTU试验结果得到的摩阻比变化范围较大,在0～8之间远大于一般的砂土或黏土的变化范围,摩阻比与修正端阻之间的关系可用双曲线近似表示。建议进行静力分析时,迭层土不排水抗剪强度参数选取应参考CPTU试验结果。 相似文献
4.
近年来许多研究者致力于通过孔压静力触探(CPTU)确定土体的渗透系数,但是存在偏差大,而且不能从机制上清楚地解释孔压静力触探确定土体渗透系数的原因。为了应用孔压静力触探现场快速地确定土体的渗透系数,在总结前人对孔压静力触探确定土体渗透系数方法的研究基础上,提出孔压静力触探时锥头处呈球冠形孔隙水流动的计算模型,假定锥头处初始超孔隙水压力为负指数型分布,推导出土体渗透系数的表达式,并且结合现场实测数据,将所提出的方法与已有的方法进行对比分析。研究发现：所提出的方法扩大了现有方法的应用范围;渗透系数计算结果受锥头角度的影响较大,随着锥头角度的增大而增大;针对国际上通用的60°角的标准锥头,所提出的方法计算的渗透系数大于前人的方法,而且更接近室内外试验结果。 相似文献
5.
6.
土的工程分类是工程勘察和设计应用的关键问题之一。基于孔压静力触探测试（piezocone penetration test,简称CPTU）原位测试参数进行土分类是高效实用的方法。国内外现有分类方法的名称及标准与我国《水运工程岩土勘察规范》（JTS 133－2013）不符合。因此,建立基于CPTU原位测试参数、符合我国行业标准的土工程分类方法具有重要工程意义。在收集大量国内外水运工程CPTU测试资料的基础上,对比分析了616个间距小于5 m的CPTU测试孔和相应钻孔取样与室内土工试验成果。选择国内外7种常用的CPTU土分类图进行应用比较,发现这些土分类图所采用的应力修正计算方法在考虑浅层土体的有效上覆应力修正时存在一定的缺陷,通过引入新的应力修正方法和修正土分类边界线,建立了适合我国水运工程的CPTU土分类方法。对比应用分析表明,该分类图能够准确地进行水运工程土类划分,尤其适合于软土、粉细砂和中粗砂的划分,可作为我国水运工程的土工程分类方法。 相似文献
7.
8.
采用轴平移技术对砂土、粉质黏土、黏土3种土质的土-水特征曲线进行了测试分析,并结合核磁共振技术测得了试样在不同基质吸力加载步条件下的T2时间（横向弛豫时间）分布曲线,从细微观角度分析了脱湿过程中孔隙水在土体中赋存分布的情况。实验结果表明:3种土质的体积含水率随着控制吸力的增大而减少,该脱湿曲线可分为边界效应区、过渡区与残余区3个区域。其中,黏土的持水特性明显大于粉质黏土和砂土。核磁共振的试验结果与压力板仪获得的脱湿过程是对应的,从微细观角度展示了土体的排水过程。在排水过程中,总体上具有较大势能的大孔隙水先排出,随后小孔隙开始排水,但这一规律并不绝对,由于土体孔隙结构的复杂性,会出现大小孔隙同时排水以及土样中水分重分布的现象。 相似文献
9.
本文介绍了对以饱和粘性土为介质的模型槽中所进行的孔压静力触探(CPTU)试验,通过对试验数据的分析,得出探头贯入时周围土体的轴向附加应力和径向附加应力的变化及分布,锥尖、侧壁摩阻力以及超孔隙水压力的变化,以及停止贯入后孔压消散过程中探头周围土体的超孔压变化,从这些方面来探讨土中应力场的变化,附加应力的影响范围,临界深度现象以及超孔隙水压力的变化规律。 相似文献
10.
孔压静力触探试验(CPTU)是目前使用最为广泛的原位测试方法之一,但CPTU不能原位测量土体最基本的指标——密度。密度孔压静力触探试验(DCPTU)是把核子密度仪结合到孔压静力触探系统中,贯入过程中可以同时测量锥尖阻力、侧壁摩阻力、孔隙水压力和密度的一种新型原位测试方法。本文首先介绍了DCPTU的试验装置和密度测试理论;然后通过与室内试验结果对比评价了利用DCPTU测量砂土、黏土、填土地层以及海底淤泥的密度的可靠性,分析了非均质地层中DCPTU测量密度与真实密度的区别、并提出了真实密度剖面的推求方法;然后综述了DCPTU在判别软弱夹层、评价砂土的液化势、检验地基处理效果、检测块状填土中的空隙、调查浮泥层的厚度和密度分布等方面的工程应用;最后展望了DCPTU在工程勘察中的发展趋势和应用前景。 相似文献
11.
基于收缩试验的膨胀土地基变形预测方法 总被引：9，自引：1，他引：8
进行膨胀土的三相收缩试验,确定了广西膨胀土的体积收缩指数。对依托工程膨胀土进行了现场静力触探试验,根据比贯入阻力随深度的变化曲线特征,确定了膨胀土活动区深度,给出了膨胀土裂隙开展深度的理论解,膨胀土裂隙开展深度的计算值与静力触探试验确定的膨胀土活动区深度和现场观测的裂隙开展深度基本一致。最后介绍了基于三相收缩试验基础上的膨胀土地基变形计算方法,并在试验基础上给出了膨胀土地基变形计算模式和计算结果。以膨胀土地基变形量作为膨胀土地基的分类指标,对膨胀土地基进行了分类,对膨胀土基础选型具有重要意义。 相似文献
12.
原位测试技术分析软土的应力历史可以避免取样及室内土工试验对土样的扰动,其结果能真实地反映现场土体的工程特性。以往基于孔压静力触探（CPTU）测试技术的超固结比（OCR）计算方法主要是针对超固结土取得的,缺乏对现场处于欠固结状态土体的考虑,具有一定的局限性。在已有研究成果的基础上,提出采用不完全孔压消散曲线的末段及时间平方根倒数外推法计算原位初始孔压,如果初始孔压大于静水压力,表明原位土层中存在固有孔压,为欠固结土。在此基础上,通过计算固结状态参数,可进一步对软土层的欠固结程度进行定量评价。工程应用表明,该方法不受软土性质和地域限制,具有普遍适用性,是合理可行的。在缺乏室内固结试验成果的情况下,可高效快捷地判别软土层的固结状态。研究成果对合理评价欠固结软土的工程特性具有一定的指导意义。 相似文献
13.
14.
采用离散元商业软件PFC2D对7种重力场下静力触探试验进行了对比分析试验,以研究高、低重力场下静力触探试验的异同点。数值试验结果表明：不同重力场下土体受静力触探贯入主要影响区域不同,低重力场下主要是上部土体受到影响,高重力场下主要是下部土体受到影响;归一化贯入阻力的最大值和稳定值、归一化球应力和偏应力的最大值均与重力加速度的倒数呈线性关系,均随重力加速度倒数的增加而增大;土体经历了明显的加载、卸载过程,重力加速度越小,加载、卸载现象越明显,同一重力加速度下上部土体加载、卸载程度大于下部土体。 相似文献
15.
The study is concerned with the influence of various factors on vibro compaction in calcareous soils, This include effect
of carbonate content, and influence of pore water pressures in sand, settlements during vibrocompaction, vibroaccelerations
during sand column installation compared to earthquake accelerations and finally the liquefaction design based on average
CPT parameters. Previous experiences with calcareous sands and literature review confirm the necessity to apply a correlation
factor for calcareous material to the raw cone penetration resistance CPT values obtained in the field. Because of the very
fragile grains of the Dubai calcareous sands the penetration resistance will be influenced by crushing and grinding. To accommodate
for effect of calcareous sands on measured CPT values, a best fit correlations formula called here “correlation factor” is
developed. A parametric dynamic triaxial liquefaction testing programme has been executed on representative samples with loose
and dense zones. Representative testing parameters for field conditions and earthquake design accelerations have been applied
indicating that ground improvement is necessary. It was observed during the dynamic triaxial tests that the whole soil mass
consisting of dense columns and looser zones in between behaves jointly, and therefore compaction control using an average-CPT
approach is possible. 相似文献
16.
Finite element cavity expansion analysis investigating the effect of penetration rate on piezocone tests in clay is presented. A coupled analysis was performed, in which the rate of cavity expansion was linked to the penetration rate of the cone and the cone angle, using the assumption that the deformation was wholly radial, and took place only between the cone tip and the cone shoulder. The soil was modelled using modified cam clay with two sets of parameters and varying values of overconsolidation ratio (OCR). The influence of penetration rate on the stress and pore pressure distributions was examined. For slower penetration rates, the excess pore pressure at the cone shoulder is lower since consolidation is permitted coincident with penetration. The radial profiles of post‐penetration voids ratio demonstrate that partially drained penetration is permitted by volume change in the near field, in addition to radial movement in the far field. The radial distribution of excess pore pressure after slow penetration differs from the undrained case, with a relatively low radial gradient existing at the cone face. As a result, the dissipation curves after slow penetration lag behind those following fast penetration. The cone velocity is made dimensionless by normalizing with the coefficient of consolidation and the cone diameter. ‘Backbone’ curves of normalized velocity against normalized tip resistance and excess pore pressure capturing the transition from undrained to drained penetration are derived. The normalized pore pressure backbone curve is unique, whilst the normalized tip resistance shows a small dependency on OCR. These backbone penetration curves are compared with centrifuge model piezocone tests conducted at varying rates, and subsequent dissipation tests. The numerical and experimental results suggest that the value of consolidation coefficient operative during the dissipation phase is 2–4 times higher than the virgin compression value due to changes in the operative soil stiffness, as demonstrated from the stress paths of individual soil elements. The use of multi‐rate penetration tests to deduce values of consolidation coefficient is discussed, in light of these differences. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
17.
Uncompacted artificial-fill deposits on the east side of San Francisco Bay suffered severe levels of soil liquefaction during the Loma Prieta earthquake of 17 October 1989. Damaged areas included maritime-port facilities, office buildings, and shoreline transportation arteries, ranging from 65 to 85 km from the north end of the Loma Prieta rupture zone. Typical of all these sites, which represent occurrences of liquefaction-induced damage farthest from the rupture zone, are low cone penetration test and Standard Penetration Test resistances in zones of cohesionless silty and sandy hydraulic fill, and underlying soft cohesive Holocene and Pleistocene sediment that strongly amplified ground motions. Postearthquake investigations at five study sites using standard penetration tests and cone penetration tests provide a basis for evaluation of the Arias intensity-based methodology for assessment of liquefaction susceptibility. 相似文献
18.
19.
以港珠澳大桥拱北隧道明挖段基坑工程为背景,根据相似比尺理论,确定具体的试验模型,利用多功能波浪流水槽系统,研究了波浪作用下黏质粉土基坑周围的超孔压响应规律,研究发现,临海基坑周围的超孔压由振荡超孔压和累积超孔压两部分组成;振荡超孔压幅值沿着从坑外主动区到坑内被动区的渗流路径逐渐衰减,同时伴随着波动相位的滞后,且振荡超孔压幅值衰减值越大,相位滞后也就越明显;基坑主动区的超孔压以随着时间逐渐减小的速率累积,判断临海基坑周围某一位置处的超孔压累积情况,应该从该处的排水条件好坏及由波浪荷载产生的动应力大小两方面分析,排水条件越差或由波浪荷载产生的动应力越大,就越有利于该处超孔压的累积;基坑被动区的振荡超孔压及累积超孔压均相对较小。 相似文献
20.
盾构隧道施工土体扰动范围研究 总被引：1，自引：0，他引：1
盾构隧道施工,隧道周边土体应力场发生改变,临近隧道土体因应力扰动出现塑性区,塑性区的分布范围与注浆压力、注浆量等注浆参数密切相关。塑性区被认为是施工扰动比较严重的区域,为分析盾构施工扰动范围,基于小孔扩张理论研究了注浆压力、注浆量对土体扰动塑性区的影响,推导了塑性区与注浆压力和注浆量之间的函数关系。在定义扰动评价标准基础上,提出应用有限元计算盾构施工塑性区和扰动范围的一种简捷实用的数值方法。最后采用静力触探现场测试盾构施工扰动范围,并与理论公式及有限元方法进行比较,理论公式、有限元及现场测试三者取得了较为一致的结果,验证了推荐方法的有效性。其研究结果可对盾构施工注浆参数的正确选择提供理论支持。 相似文献