The source and fate of sediment and mercury in Hunza River basin,Northern Areas,Pakistan          下载免费PDF全文

Kivanc Biber  Shuhab D. Khan  Mohammad T. Shah 《水文研究》2015,29(4):579-587

This article presents results of mercury in surface waters from Hunza River basin, Northern Areas, Pakistan. Small‐scale gold mining activities along the Hunza and Gilgit rivers are long known to be discharging mercury in the amalgamation and roasting processes. Previous studies reported high mercury concentrations in soils close to mining operations as well as serious health problems for miners. However, none of the studies have focused on the level of contamination in aqueous environments. This is the first study on the investigation of source and fate of sediment and river‐borne mercury in the Hunza River. The samples collected near gold panning sites showed higher mercury concentrations than critical levels established by the U.S. Environmental Protection Agency. The observed dissolved mercury concentrations ranged from 5.10 to 25.25 ng/l, whereas particulate‐bound mercury ranged from 4.85 to 154.62 ng/l. Particulate‐phase mercury corresponded to more than 75% of the total observed mercury concentrations for all of the sampled rivers. Thus, suspended sediments represented the major pathway of the riverine mercury transport. A mass balance calculation suggested an annual mercury flux of 48.6 g/km² into the Hunza River basin. The samples collected from the most affected river, the Shimsal River, averaged to have 108 ng/l total mercury. This amount was close to the average soil mercury data of 151 ng/l as reported by the Pakistan Mineral Development Corporation in 2001. The dominant source of contamination was shown to be the leaching of large quantities of mercury from the mercury‐rich sediment and flood plain soil into the rivers, rather than the direct release from mining activities. Significant decrease in both dissolved and particulate‐bound mercury concentration downstream of Attabad Lake suggested that mercury is being accumulated or consumed in the lake. Although minimization or elimination of mercury loses from the mining process seems important for the well‐being of the miners, preventing the remobilization of accumulated mercury is equally important in mercury control in this region. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

Sediment Hosted Primary Tin Deposit Associated with Biotite Granite and Fault Zone at Gunung Paku, Klian Intan, Upper Perak, Malaysia     

Kamar Shah Ariffin 《Resource Geology》2009,59(3):282-294

Gunung Paku near Klian Intan, Perak, is a primary tin deposit in Malaysia mined since 200 years ago, contributing 3–5% of tin ore concentrates previously, and recently over 70% of the Malaysian tin. Gunung Paku is located within the western Tin belt of Peninsular Malaysia associated with biotite granite (184–230 Ma) of the Main Range Granitoid which extends up to the southern part of Peninsular and Central Thailand. The primary tin mineralization style at the Gunung Paku is mainly associated with widespread occurrence of sheet-like quartz veining systems parallel to the strike of the host rocks and confined within a narrow N–S trending fault zone. The mineralization formed within a thick sequence of metasedimentry rock that belongs to the Baling Formation of Palaeozoic age. The host rock of weakly metamorphosed argillite generally experienced strong tropical weathering that resulted in a thick sequence of light grey to light brown oxidized profile. The mineralized veins range from simple quartz-cassiterite, quartz-tourmaline-cassiterite to complex quartz-cassiterite-polymetallic sulfide veins. Wall rock alterations at Gunung Paku are mainly characterized by the hypogene type alteration consisting of silicification, tourmalinization, chloritization, sericitization and kaolinization normally adjacent to mineralized quartz veins and brecciated-fault gouge zones. Pyrite, arsenopyrite, cassiterite, rutile, chalcopyrite, trippkeite (CuAsO4), scorodite, covellite and other secondary iron-oxyhydroxide are the common metallic minerals that accompanied the tin mineralization. Other minor occurrences include trace amounts of complex lead-bismuth-antimony-molybdenum bearing minerals.  相似文献   

Geochemistry and origin of Mn-deposits in the Waziristan ophiolite complex, north Waziristan, Pakistan     

M. T. Shah  A. Khan 《Mineralium Deposita》1999,34(7):697-704

The Waziristan ophiolite complex is located along the western margin of the Indian plate in northwestern Pakistan. The Mn-deposits in the Saidgi and Shuidar areas are part of this ophiolite complex. These deposits, both banded and massive in nature, are hosted by metachert and are generally overlying metavolcanics. Braunite and cryptocrystalline quartz are the main constituents of the manganese ores in both areas. Hematite occurs in the Shuidar deposits as a minor phase. Metacherts are microcrystalline aggregates of microcrystalline quartz, chalcedony, and lesser hematite. Chemically, the studied Mn-deposits and associated metacherts are very similar to those formed by submarine hydrothermal effusive processes. The deposits originated along sea-floor spreading centers (mid-ocean ridges) within the Neo-Tethys Ocean and were later obducted as part of the Waziristan ophiolite complex. Received: 9 January 1998 / Accepted: 10 March 1999  相似文献   

Non-axisymmetric guided waves in a composite cylinder with transversely isotropic core     

N. Rattanawangcharoen  Subhendu K. Datta  Arvind H. Shah 《Geophysical Journal International》1994,118(2):317-324

  相似文献   

Constraints on ice-sheet thickness over Tibet during the last 40 000 years     

S. K. Gupta  P. Sharma  S. K. Shah 《第四纪科学杂志》1992,7(4):283-290

The Late Quaternary glaciation of Tibet has received considerable attention in the last few decades due to its influence on the regional climate, especially the Asian summer monsoon. Recently, however, it has been argued that the Tibetan ice sheet also might have played an important role in initiating global-scale palaeoclimatic changes. Controversy, however, exists on the nature of Late Quaternary ice cover over Tibet due largely to the subjectivity in the interpretation of the sparse and complex geomorphological evidence. We have examined this problem in the light of δ ¹⁸O data (a temperature proxy) of ice cores-from the Dunde ice cap on the northern flank of Tibet. Considering only the gross features in the Dunde ice-core isotopic data, we have interpreted a temperature decrease of 4°–6°C and consequent lowering of equilibrium line altitude (ELA) in the range 700–850 m during the last glacial stage (LGS). This could have caused depression of the snow line below the mean altitutde of the Tibetan plateau, resulting in an areally extensive but marginally thick ice cover. However, if one also considers the possibility that precipitation on the Tibetan plateau during LGS may have been significantly lower than at present, the ELA depression would be much less than that estimated by considering the temperature effect alone.  相似文献   

Duration of Eo-Alpine metamorphic events obtained from multicomponent diffusion modeling of garnet: a case study from the Eastern Alps   总被引：2，自引：2，他引：0  

Shah?Wali?FaryadEmail author  Sumit?Chakraborty 《Contributions to Mineralogy and Petrology》2005,150(3):306-318

Rocks from the Micaschist–Marble Complex of the Wölz Tauern, which are part of the middle Austroalpine unit, contain large (up to 2 cm) garnet crystals that show clear evidence of multistage growth. Isotopic dating indicates that a Variscan (～270 Ma) garnet core was overgrown by new garnet formed during Eo-Alpine metamorphism at Cretaceous times. P-T paths for the Eo-Alpine metamorphism were obtained using the method of pseudosections (Powell and Holland in Metam Geol 16:309–343, 1998) and are consistent with earlier results from independent thermobarometry. Due to the large size of the garnets, growth zoning was preserved during amphibolite facies metamorphism at both Variscan and Alpine times. Full multicomponent diffusion modeling of compositional zoning at the interface of the Alpine and Pre-Alpine garnets in conjunction with the retrieved P-T paths allow average subduction/exhumation as well as heating/cooling rates to be retrieved. The modeling suggests that a minimum subduction/exhumation rate of ～4 cm/a and heating/cooling rates on the order of 100–260°C/Ma for a 60°C subduction angle are required to preserve the observed compositional zoning overall while modifying the zoning at the interface between two garnets to the extent observed. Such rapid rates of burial/exhumation are consistent with the results of direct GPS measurements of convergence rates at several orogenic belts as well as with inferred rates from modeling in the Alps and other areas. In combination, this indicates that such rapid rates are commonplace during metamorphism in collisional orogens and places important constraints on the rheological behavior of crustal blocks in such orogens.  相似文献   

Solar X-ray Spectrometer (Soxs) Mission on Board GSAT2 Indian Spacecraft: The Low-Energy Payload     

Rajmal Jain  Hemant Dave  A. B. Shah  N. M. Vadher  Vishal M. Shah  G. P. Ubale  K. S. B. Manian  Chirag M. Solanki  K. J. Shah  Sumit Kumar  S. L. Kayasth  V. D. Patel  Jayshree J. Trivedi  M. R. Deshpande 《Solar physics》2005,227(1):89-122

The first space-borne solar astronomy experiment of India, namely Solar X-ray Spectrometer (SOXS), was successfully launched on 08 May 2003 on board geostationary satellite GSAT-2 of India. The SOXS is composed of two independent payloads, viz. SOXS Low-Energy Detector (SLD) Payload and SOXS High-Energy Detector (SHD) Payload. The SOXS aims to study the full-disk integrated X-ray emission in the energy range from 4 keV to 10 MeV. In this paper we present the first report on the SLD instrumentation and its in-orbit performance. The SLD payload was designed and developed at the Physical Research Laboratory in collaboration with various centers of Indian Space Research Organisation (ISRO). The basic scientific aim of the SLD payload is to study solar flares in the energy range from 4 to 60 keV with high spectral and temporal resolution. To meet these requirements, the SLD payload employs state-of-the-art solid state detectors, the first time for a solar astronomy experiment, viz. Si PIN (4 –25 keV), and cadmium–zinc–telluride (4 –60 keV). With their superb high-energy resolution characteristics, SLD can observe iron and iron–nickel complex lines that are visible only during solar flares. In view of its 3.4 FOV, the detector package is mounted on a Sun Aspect System, for the first time, to get uninterrupted observations in a geostationary orbit. The SLD payload configuration, its in-flight operation, and the response of the detectors are presented. We also present the first observations of solar flares made by the SLD payload and briefly describe their temporal and spectral mode results.  相似文献   

Load Settlement Behaviour of Fly ash Mixed with Waste Sludge and Cement     

Malik Shoeb Ahmad  S. S. Shah 《Geotechnical and Geological Engineering》2016,34(1):37-58

One of the effective utilization strategies for fly ash and waste sludge is to use it as a fill material to raise low lying areas. Bearing capacity and settlement are the required input for the design of foundations on such fills. To determine the bearing capacity, plate load tests were carried out on the compacted beds of fly ash, fly ash-waste sludge and fly ash-waste sludge–cement. The tests were conducted by keeping 90, 95 and 100 % relative compaction, fresh and fresh submerged conditions, aged (28 days) and aged (28 days) submerged conditions as variables of the tests. The load-settlement curves were plotted for fly ash and mix blends. The minimum load was obtained for fly ash under submerged condition, further the test results show that the fly ash becomes flowable on submergence. On the other hand when the fly ash was mixed with waste sludge and cement, the load carrying capacity was found to improve to a greater extent. Test beds prepared with fly ash–cement-waste sludge under as compacted condition (fresh) show very high load carrying capacity (1600–2180 kN/m²). An analytical method has also been validated for fly ash–cement-waste sludge mix which was developed to estimate the settlement of footing resting on fly ash taking into account the pre-consolidation stresses. The non linearity of load-settlement behavior was appropriately modeled, on the basis of available plate load test data incorporated in the method. The method requires as input, the pre-consolidation stress and Young’s modulus of compacted mix of fly ash-waste sludge–cement. A comparison of load-settlement values observed in plate load tests and predicted values for the mix 47 %FA + 45 %S + 8 %C, using the proposed method shows good agreement. Hence, this relationship may also be useful to the field engineers to check the reported load-settlement values for such types of mixes in the field.  相似文献   

Image processing and GIS techniques applied to high resolution satellite data for lineament mapping of thermal power plant site in Allahabad district,U.P., India     

Aniruddha Uniyal  P.N. Shah  Rajiva Mohan  S. Rao 《国际地球制图》2016,31(9):956-965

The present study is based on digital analysis of IRS 1C/1D LISS-III and IRS P6 LISS-IV images for identification of lineaments in Meja Thermal Power Plant site in Allahabad district. In spite of all limitations due to anthropogenic activities of stone quarrying and criss cross unmetalled roads, almost non-existent vegetation indicators and soil moisture, the efforts were made to identify and map a number of lineaments in the study area and these were subsequently verified in the field. Most of the lineaments identified and mapped are not having any major displacement along them or are not displacing or truncating any major rock unit. Field investigations have revealed that there is no drastic change in the trend of rocks along the lineaments mapped in the study area. On the basis of digital analysis of IRS P6 LISS-IV data NE–SW and NW–SE trending lineaments have been identified and mapped. Some NNE–SSW trending lineaments have also been mapped. All the lineaments demarcated in this area still need to be correlated with the seismic data of the area by superimposing the microseismicity data over lineaments.  相似文献   

Chromium uptake by giant reed under rhizobacterial inhibition     

S. Shaheen  Q. Mahmood  A. Pervez  N. Mirza  Z. A. Bhatti  T. Hayat  S. S. Meryem  F. Ullah 《International Journal of Environmental Science and Technology》2016,13(6):1581-1590

The role of rhizospheric microbes of giant reed (Arundo donax L.) in Cr uptake from hydroponic culture was investigated. The control group was exposed to Cr in range of 25–100 mg L^?1 containing a control itself (with no metal addition). The experimental group received same Cr treatments, but in addition was exposed to antibiotic treatment in order to inhibit rhizospheric bacteria. The range of Cr accumulated in the roots was 3–7.65 mg L^?1; in stem it ranged 2.15–42.4 mg kg^?1; while in leaves, the range of Cr content was 13.7–15 mg kg^?1. Overall, Cr uptake in A. donax (without rhizobacterial inhibition) was root < leaf < stem. However, the amount of Cr uptake in plants with rhizobacterial inhibition was significantly less (~4.6-folds in 100 mg L^?1 Cr treatment) than those without such inhibition clearly highlighting that rhizobacterial inhibition decreased the Cr uptake. The experimental results clearly demonstrated that the inhibition of the rhizobacterial populations had great influence on the Cr uptake. However, Cr uptake could not be completely inhibited as some metal uptake was observed after the rhizobacterial inhibition although it was significantly less than the Cr uptake of plants without such inhibition.  相似文献