大陆岩石圈在张裂和分离时的变形模式   总被引：4，自引：0，他引：4  

姚伯初 《海洋地质与第四纪地质》2002,22(3):59-67

通过对南海南北共轭边缘地壳剖面的对比研究,发现大陆岩石圈的物理性质是分层的：上、中地壳呈脆性,下地壳表现出塑性,而岩石圈上地幔则仍呈脆性。因此,在它受张性应力场作用时,其变形和破裂分离方式也是分层进行的：上、中地壳能发生犁式断裂,产生的断块沿断面转动在地表产生一系列半地堑,并使地壳厚度减薄;如拉张应力继续作用时,上、中地壳将沿犁式断裂被拉开,从而形成上、下板块边缘,并彼此分开。下地壳则发生塑性变形,使地壳厚度减薄,并最终将其拉断。岩石圈上地幔亦可产生陡倾断裂,形成的断块沿断面转动亦使其厚度减薄,并最终沿陡倾断裂被拉断。这就是我们称之为岩石圈变形和破裂分 离时的分层变形及分层破裂分离模式。  相似文献   

Estimation of Axial Pile Bearing Capacity According to Shear Strength Parameters of Soil     

Yu Xiaodong  Yan Shuwang Sun Wanhe Postgraduate Student  Tianjin University  Tianjin Professor  Tianjin University  Tianjin Senior Engineer  Tianjin Port Engineering Institute  Tianjin 《中国海洋工程》1997,(2)

At pesent,it is very popular to estimate pile bearing capacity by use of empirical formula andphysical indexes of soil provided in the design codes for civil construction in China.This paper attempts toapply mechanical indexes of soil and semi-empirical formulas,which are based on soil mechanical theoriesand were summarized and presented by Meyerhof in 1976,to calculate the axial pile bearing capacity.Lo-ading test results of 24 single piles in Tianjin area have been collected and compared with the proposed cal-ulation approach.  相似文献   

Shear Failure of a Clamped Dented Tubular Beam Under Lateral Impact   总被引：1，自引：0，他引：1  

Wang Deyu  Zhang Shanyuan Associate Prof.  Depart  of Naval Archi.  Ocean Engineering  Shanghai Jiaotong University  Shanghai Prof.  Research Institute of Applied Mechanics  Taiyuan University of Technology  Taiyuan 《中国海洋工程》1996,(2)

- The shear failure of a rigid-plastic dented clamped tubular beam under the lateral impact of a mass is investigated. Both the denting and the impact point are in the middle span of the beam. It is assumed that denting does not spread during the shear sliding. Numerical results show that the axial force and lateral deflection of the beam are very small at the moment of the occurence of shear failure, which means that the finite deformation effect can be neglected in the shear failure analysis. Also, some aspects of the initial impact energy are investigated.  相似文献   

Comparison of Strain-rate Dependent Stress-Strain Behavior from Ko-consolidated Compression and Extension Tests on Natural Hong Kong Marine Deposits     

Jian-Hua Yin  Chun-Man Cheng 《Marine Georesources & Geotechnology》2006,24(2):119-147

This article presents results from a series of K_o-consolidated compression and extension triaxial tests on specimens from undisturbed samples of Hong Kong Marine Deposits (HKMD). To investigate the strain-rate effects, a total of seven K_o-consolidated triaxial tests were conducted including four compression tests and three extension tests. After K_o-consolidation, the triaxial test specimens were sheared at step-changed axial strain rates under three different confining pressures of 50 kPa, 150 kPa, and 400 kPa, respectively. The step-changed strain rates were applied in the following order: +2%/h, +0.2%/h, +20%/h, -2%/h (unloading) and +2%/h (reloading) for the four compression tests and -2%/h, -0.2%/h, -20%/h, +2%/h (unloading) and -2%/h (reloading) for the three extension tests. The results are reported and analyzed in the paper. The results show that the strain rate effects, the stress-strain characteristics, and the effective stress paths of the specimens for tests in a compression state are different from those for tests in an extension stage. One order of magnitude increase in axial strain rate causes an average 8.6% increase in undrained shear strength for compression tests and a 12.1% increase for extension tests. It is also found that the failure mode of the specimens in compression is different from that in extension. The stress-strain behavior of specimens shows strain-softening and a clear shear band in compression tests, but strain-hardening without any clear shear band in extension tests for the same absolute value of axial strain.  相似文献   

Numerical study of enhanced energy dissipation near a seamount     

Nobuyuki Iwamae  Toshiyuki Hibiya  Yoshihiro Niwa 《Journal of Oceanography》2006,62(6):851-858

Using a two-dimensional primitive equation model, we examine nonlinear responses of a semidiurnal tidal flow impinging on a seamount with a background Garrett-Munk-like (GM-like) internal wavefield. It is found that horizontally elongated pancake-like structures of high vertical wavenumber near-inertial current shear are created both in the near-field (the region over the slope of the seamount) and far-field (the region over the flat bottom of the ocean). An important distinction is that the high vertical wavenumber near-inertial current shear is amplified only at mid-latitudes in the far-field (owing to a parametric subharmonic instability (PSI)), whereas it is amplified both at mid-and high-latitudes (above the latitude where PSI can occur) in the near-field. In order to clarify the generating mechanism for the strong shear in the near-field, additional numerical experiments are carried out with the GM-like background internal waves removed. The experiments show that the strong shear is also created, indicating that it is not caused by the interaction between the background GM-like internal waves and the semidiurnal internal tides. One possible explanation is proposed for the amplification of high vertical wavenumber near-inertial current shear in the near-field where tide residual flow resulting from tide-topography interaction plays an important role in transferring energy from high-mode internal tides to near-inertial internal waves.  相似文献   

伶仃洋L＿2和L＿（16）孔第四纪有孔虫群与孢粉化石带特征及其地质意义   总被引：5，自引：0，他引：5  

陈木宏  赵焕庭  温孝胜  张乔民  宋朝景 《海洋地质与第四纪地质》1994,(1)

本文所依据的分析样品是取自珠江最大的一个河口湾伶仃洋中部的水下钻孔岩芯，其底部到达花岗岩基底。通过对第四纪有孔虫群与孢粉化石带特征的分析，阐明在相同的钻孔岩芯中，有孔虫分布变化所反映的古沉积环境特征与孢粉分析的古气候特征较为吻合，并与相应的沉积相对应，结合￣（１４）Ｃ和￣（２３０）Ｔｈ／￣（２３２）Ｔｈ比值法测年数据，从而较好地重塑本区晚更新世中期以来的地质历史。  相似文献   

辽东湾S2冰侧限剪切强度的试验研究   总被引：3，自引：0，他引：3  

李志军孟广琳  高树刚刘培林 《海洋工程》2002,20(1):20-23

利用试验方法系统地研究了辽东湾S2型海冰侧限剪切强度随剪切应变速率、加载方向、法向应力、温度和冰内孔隙率的变化规律。介绍了S2型海冰各向异性特点及剪切应变速率对剪切破坏方式的效应和韧脆破坏转变的条件。分析了不同加载方向海冰峰值剪切强度的差异 ,获得 - 6 2℃温度下S2冰内摩擦角和内聚力分别为 42°和 70 0kPa。利用统计分析给出峰值剪切强度与冰温和孔隙率的试验关系  相似文献   

Gradation affects basic mechanical characteristics of Chinese calcareous sand as airport subgrade of reefs     

Shen Yang  Xue Shen  Hanlong Liu  Huayang Ge  Xiaoxi Rui 《Marine Georesources & Geotechnology》2020,38(6):706-715

Abstract

Construction of the reefs in the South China Sea is a significant foundation to the secure stability and economic development of China. The construction of an airport runway is necessary for this realization. The calcareous sand is the main primary material in the runway construction. A certain type of calcareous sand near a certain reef of the South China Sea was studied in this paper. To investigate this specific calcareous sand, quartz sand was used as a reference for comparison. Microscopic 3-D imaging, compression and triaxial tests were conducted to test the micro, squeezing and shear properties. The effect mechanism of gradation on the calcareous sand’s compressibility and shear characteristics are discussed from a mesoscopic viewpoint using 3-D morphology. Calcareous sand particles are multiangular and flatter in comparison with quartz sand. The larger the particle sizes are, the more different the two sands’ morphologies are. The compressibility of calcareous sand is greater, and the effect of the coarse fraction (5–1?mm) content in the gradation plays the most significant role in this feature. When the coarse particles’ content is less than 25% and the mass ratio of the middle and fine particles (M) is constant, there is the worst coarse fraction content causing the calcareous sand to be most likely compressed. The worst coarse fraction content decreases with the increase in M, and an empirical formula is proposed. When the gradation, relative density and confining pressure are the same, the peak shear stress and strain of calcareous sand are all at a high level. The effect of confining pressure is manifested in calcareous sand. The shear strength and dilation of calcareous sand are also most affected by the medium coarse fraction (5–0.25?mm) content.  相似文献   

The Mid-atlantic Ridge (31°S–34°30′S): Temporal and spatial variations of accretionary processes     

P. J. Fox  N. R. Grindlay  K. C. MacDonald 《Marine Geophysical Researches》1991,13(1):1-20

The ridge located between 31° S and 34°30′S is spreading at a rate of 35 mm yr⁻¹, a transitional velocity between the very slow (≤20 mm yr⁻¹) opening rates of the North Atlantic and Southwest Indian Oceans, and the intermediate rates (60 mm yr⁻¹) of the northern limb of the East Pacific Rise, and the Galapagos and Juan de Fuca Ridges. A synthesis of multi-narrow beam, magnetics and gravity data document that in this area the ridge represents a dynamically evolving system. Here the ridge is partitioned into an ensemble of six distinct segments of variable lengths (12 to 100 km) by two transform faults (first-order discontinuities) and three small offset (< 30 km) discontinuities (second-order discontinuities) that behave non-rigidly creating complex and heterogeneous morphotectonic patterns that are not parallel to flow lines. The offset magnitudes of both the first and second-order discontinuities change in response to differential asymmetric spreading. In addition, along the fossil trace of second-order discontinuities, the lengths of abyssal hills located to either side of a discordant zone are observed to lengthen and shorten creating a saw-toothed pattern. Although the spreading rate remains the same along the length of the ridge studied, the morphology of the spreading segments varies from a deep median valley with characteristics analogous to the rift segments of the North Atlantic to a gently rifted axial bulge that is indistinguishable from the shape and relief of the intermediate rate spreading centers of the East Pacific Rise (i.e., 21°N). Like other carefully surveyed ridge segments at slow and fast rates of accretion, the along-axis profiles of each ridge segment are distinctly convex upwards, and exhibit along-strike changes in relief of 500m to 1500 between the shallowest portion of the segment (approximate center) and the segment ends. Such spatial variations create marked along-axis changes in the morphology and relief of each segment. A relatively low mantle Bouguer anomaly is known to be associated with the ridge segment characterized by a gently rifted axial bulge and is interpreted to indicate the presence of focused mantle upwelling (Kuo and Forsyth, 1988). Moreover, the terrain at the ends of each segment are known to be highly magnetized compared to the centers of each segment (Carbotte et al, 1990). Taken together, these data clearly establish that these profound spatial variations in ridge segment properties between adjoining segments, and along and across each segment, indicate that the upper mantle processes responsible for the formation of this contrasting architecture are not solely related to passive upwelling of the asthenosphere beneath the ridge axis. Rather, there must be differences in the thermal and mechanical structure of the crust and upper mantle between and along the ridge segments to explain these spatial variations in axial topography, crustal structure and magnetization. These results are consistent with the results of investigations from other parts of the ridge and suggest that the emplacement of magma is highly focused along segments and positioned beneath the depth minimum of a given segment. The profound differences between segments indicate that the processes governing the behavior of upwelling mantle are decoupled and the variations in the patterns of axis flanking morphology and rate of accretion indicate that processes controlling upwelling and melt production vary markedly in time as well. At this spreading rate and in this area, the accretionary processes are clearly three-dimensional. In addition, the morphology of a ridge segment is not governed so much by opening rate as by the thermal structure of the mantle which underlies the segment.  相似文献   

A Preliminary Study of Shear Wave in Seafloor Surface Sediments   总被引：1，自引：0，他引：1  

Bo Lu  Ganxian Li  Shaojian Huang 《Marine Georesources & Geotechnology》2006,24(1):17-28

This article preliminarily reports and analyses the transmission characteristics and behaviors of shear wave in the offshore seafloor surface sediments in China, discusses the relationships between the physical and mechanical features of the shear wave and the compression wave, and compares the testing results with that of Hamilton and Chen et al. The result shows that the shear wave can be tested if the seafloor surface sediment has tangent modulus. The shear wave velocity ranges from 50-600 m/s and the measuring frequency from 50-200 kHz. The sound velocity rate of shear wave and compression wave can be used to appraise the stress-strain feature of seafloor surface sediments. This study provides a basis for further describing and appraising the seafloor sedimentary acoustic-mechanical feature and building a geological-acoustic model on China's offshore sea area.  相似文献