排序方式： 共有51条查询结果，搜索用时 15 毫秒
1.
2.
3.
A. Torabian A. H. Hassani S. Moshirvaziri 《International Journal of Environmental Science and Technology》2004,1(2):103-107
In this research, physical, chemical and biological treatability of Tehran solid waste leachate was studied. Results indicate that the amount of COD for the fresh raw leachate of Tehran is equal to 66,608 mg/l. The leachate is transferred to an equalization tank for storage and pH control process. After neutralization, leachate is introduced to an up flow and down flow anaerobic reactor. The effluent of anaerobic reactor is conducted to a sequencing batch reactor. Sequence batch reactor (SBR) effluent was pumped in to sand and activated carbon filters, after chemical coagulation and clarification. Results showed that anaerobic reactor with detention time of 3 days had a 35% COD removal and increasing the detention time to 4.5 days would improve the COD removal to 45%. Nutrient adjustment with phosphorus and nitrogen increased the initial 23% efficiency of sequence batch reactor to 44%. The effluent COD of SBR reactor was 21,309 mg/l. Recycling of aerobic reactor effluent with incoming feed to anaerobic reactor reduced the anaerobic reactor influent COD to 20,000 mg/l and this caused 53% and 57% COD removal in the anaerobic and aerobic effluent, respectively. The total systems COD performance increased to 80% and SBR effluent COD eventually reduced to 4,000 mg/l. Coagulation, flocculation and sedimentation processes were practiced to make the 4,000 mg/l effluent COD comply with environmental standards of Iran. The optimum coagulant found to be ferric chloride with the dosage of 50 mg/l at pH of 12, which reduced 10% of COD to an amount of 3,676 mg/l. The effluent was stored in a tank and then pumped in to pressure sand filter and afterwards to activated carbon filter. The COD removal was three and 90% for sand and activated carbon filters, respectively. The total process reduced the remaining COD to 36 mg/l, which is in compliance with environmental standards of Iran. 相似文献
4.
Summary This investigation concerns 3 longwall faces having variable strata and mining conditions, but supported by 202 tonnes hydraulic 6-leg chocks. Bearing capacity tests along the faces were conducted to evaluate the factors influencing floor deformation and failure. The effect of size, shape and perimeter of the base plates, thickness of the floor layer, time and moisture on the ultimate bearing capacity of the floor was measured and discussed. Application of this work is the prediction of stability and support performance of face ends, as well as the design of support systems and ground control on production faces. 相似文献
5.
Hydro-mechanical evaluation of stabilized mine tailings 总被引：3，自引：0，他引：3
6.
M. M. Taghizadeh M.Sc. A. Torabian M. Borghei A. H. Hassani 《International Journal of Environmental Science and Technology》2007,4(4):505-512
Cheapest and simplest techniques of filtration systems are required for rural water treatment in developing countries. Using a filter made of blocks for the water treatment enables us to make porous concrete filter and use it vertically. It is expected that the required area would decrease by more than 70 % if porous concrete filters were used vertically. The operation and backwash mode would be simpler than using horizontal sand filters as filters made of blocks would be used instead. The feasibility study focused on finding adequate materials, compositions and methods of making a block with enough resistance to water pressure, sufficient porosity for water transformation and using inexpensive and available materials. A pilot study was performed to determine an appropriate thickness of filter. Testing the porous filter in another pilot study using the low overflow rate of river water showed biological growth in that media and an adequate efficiency of about 90–100 % was obtained for decreasing the coliform bacteria. The required backwash water was 2.9 % of total treated water. 相似文献
7.
Faiza Menjour Toufik Remmal Mustapha Hakdaoui Fouad El Kamel Kawtar Lakroud Fouad Amraoui Iz-Eddine El Amrani El Hassani Benjamin Van wyk de vries Pierre Boivin 《Journal of the Indian Society of Remote Sensing》2017,45(6):1015-1030
Karst formation geometry can be controlled by fractures and faults, and by other lithologies. Here we show the organization of kastic collapse features related to structures and to extensive basaltic lava flows in the Middle Atlas of Morocco. A lineament map of major faults and fractures has been created for the Middle Atlas using Landsat 7 ETM+ satellite images. This shows a dominant NE–SW regional direction and less prominent NNW–SSE and ENE–WSE directions. All these directions coincide with the alignments of karstic depressions that have formed in the Liassic limestones. The basaltic flows covering these formations on the Middle Atlas limestone plateau, have allowed the generation of cryptokarst, geometrically organized a long these major lineament directions. Karst landforms probabaly existed before the eruption of the lavas, but there were partly invaded by intrusions and volcanism. The extensive basaltic flows allowed for increased infiltration, and subsurface water flow, increasing the rate of kast formation after eruptions. Some basins show evidence of increased subsidence after lava emplacement (Aguelmam Sidi Ali Lake) and some maar-like craters also have subsided after eruption, by karts formation. We lay out the structural and lithological controls on Karstic formation in an intraplate volcanic field based on limestones and evaporites. 相似文献
8.
Abouzar Jafari Mohammad Reza Ghasemi Habib Akbarzadeh Bengar Behrooz Hassani 《Bulletin of Earthquake Engineering》2018,16(2):831-858
Self-centering rocking walls offer the possibility of minimizing repair costs and downtimes, and also nullify the residual drift after seismic events, thanks to their self-centering properties. In this paper, the effect of axial stress ratio on the behavior of monolithic self-centering rocking walls is investigated by utilizing a developed finite element model. To verify the validity of the finite element model, results and observed damage in the model are compared with those of a full-scale wall test. The axial stress ratio is varied from 0.024 to 0.30 while keeping the other structural parameters constant. For qualitative damage evaluation, the observed damage in the model compared with expected damage states of desired performance levels. In order to evaluate the incurred damage quantitatively, the amount of crushing and damage in the wall is calculated by utilizing several ratios (crushing ratio and damage ratio). Furthermore, seismic response factors (i.e., μ, R and Cd) are calculated for different axial stress ratio values. The obtained results showed that, in order to satisfy the requirements of desired performance levels, the maximum axial stress ratio should be approximately within the range of 0.10–0.15. In addition, the maximum overall damage ratio and crushing ratio are suggested to be less than 5%. For axial stress ratio higher than 0.15, the flag-shaped pattern of hysteresis curves completely disappeared and the variation of displacement ductility is less sensitive to axial stress ratio. Considering the maximum axial stress ratio limited to 0.150, values of 4 and 3.5 are conservatively proposed as a period-independent response modification factor and displacement modification factor of the investigated structural wall, respectively. 相似文献
9.
Djouher Saadoud Mohamed Saïd Guettouche Mohamed Hassani Francisco José Martin Peinado 《Arabian Journal of Geosciences》2017,10(16):363
Wind-erosion risk is a challenge that threatens land development in dry-land regions. Soil analysis, remote sensing, climatic, vegetal cover and topographic data were used in a geographic information system (GIS), using multi-criteria analysis (MCA) to map wind-erosion risk (Rwe) in Laghouat, Algeria. The approach was based on modelling the risk and incorporating topographic and climatic effects. The maps were coded according to their sensitivity to wind erosion and to their socio-economic potential, from low to very high. By overlapping the effects of these layers, qualitative maps were drawn to reflect the potential sensitivity to wind erosion per unit area. The results indicated that severe wind erosion affects mainly all the southern parts and some parts in the north of Laghouat, where wind-erosion hazard (Hwe) is very high in 43% of the total area, and which was affected mainly by natural parameters such as soil, topography and wind. The results also identified features vulnerable to Rwe. The product of the hazard and the stake maps indicated the potential risk areas that need preventive measures; this was more than half of the study area, making it essential to undertake environmental management and land-use planning. 相似文献
10.
A geomechanical model can reveal the mechanical behavior of rocks and be used to manage the reservoir programs in a better mode. Fluid pressure will be reduced during hydrocarbon production from a reservoir. This reduction of pressure will increase the effective stress due to overburden sediments and will cause porous media compaction and surface subsidence. In some oil fields, the compacting reservoir can support oil and gas production. However, the phenomena can also cause the loss of wells and reduced production and also cause irreparable damage to the surface structures and affect the surrounding environment. For a detailed study of the geomechanical behavior of a hydrocarbon field, a 3D numerical model to describe the reservoir geomechanical characteristics is essential. During this study, using available data and information, a coupled fluid flow-geomechanic model of Fahlian reservoir formation in X-field in SW of Iran was constructed to estimate the amount of land subsidence. According to the prepared model, in this field, the maximum amount of the vertical stress is 110 MPa and the maximum amount of the horizontal stress is 94 MPa. At last, this model is used for the prediction of reservoir compaction and subsidence of the surface. The maximum value of estimated ground subsidence in the study equals to 29 mm. It is considered that according to the obtained values of horizontal and vertical movement in the wall of different wells, those movements are not problematic for casing and well production and also the surrounding environment. 相似文献