导纳函数的中国南海海底地形模型   总被引：1，自引：0，他引：1  

范雕  李姗姗  孟书宇  邢志斌  李新星  冯进凯 《测绘科学》2018,(7):44-49

针对目前大面积海域依然存在海深测量数据空白的问题,该文选取中国南海4°×4°(12~16°N,115~119°E)海域范围为研究区域,通过频率域上的相关性分析,得到重力异常在30~130km波长范围与研究海域海底地形的相关程度较高。以ETOPO1海深模型作为先验模型,应用导纳函数实现了在无船测数据情况下对海深的反演,最终得到1′×1′的海深模型。将反演结果与检核点进行比较发现,模型1在2 500m以上海域相对误差较小,反演精度较高;2 500m以下海域相对误差变化大,反演精度较低。无船测数据环境下,适当加入一定数量船测海深值作为控制点得到的海深模型2,相较于未加控制点的模型1,在1 000m以下水深处的标准差明显优于模型1,与检核点的差值精度最大提高了45%左右。  相似文献   

联合多源重力数据反演菲律宾海域海底地形   总被引：2，自引：2，他引：0  

范雕  李姗姗  孟书宇  邢志斌  冯进凯  张驰 《测绘学报》2018,47(10):1307-1315

对比分析重力-海深的“理论导纳”和实际数据的“观测导纳”,获得研究海域有效弹性厚度理论值为10 km。联合重力异常和重力异常垂直梯度数据,应用自适应赋权技术,采用导纳函数方法构建菲律宾海域1'×1'海底地形模型。试验发现,当重力异常垂直梯度反演海深结果与重力异常反演海深结果的权比为2∶3时,所构建的海深模型检核精度最高。同时,联合多源重力数据反演海深能够综合重力异常和重力异常垂直梯度在对待不同海底地形上的反演优势,生成精度优于单独使用重力异常数据和重力异常垂直梯度数据反演的海底地形模型。以船测数据作为外部检核条件,反演模型检核精度略低于V18.1海深模型,而相较于ETOPO1海深模型和DTU10海深模型检核精度分别提高了27.17%和39.02%左右;反演模型相对误差的绝对值在5%范围内的检核点大约占检核点总数的94.25%。  相似文献   

鄂尔多斯盆地东胜富氦气田成藏特征及其大地构造背景^*          下载免费PDF全文

何发岐  王杰  赵永强  安川  王付斌  陶成  倪春华  贾会冲 《古地理学报》2022,24(5):937-950

近年来,在鄂尔多斯盆地北缘东胜气田上古生界天然气中发现伴生的氦气,含量分布在0.045%~0.487%范围内,具有工业价值,其三级储量约为8.3亿立方米,为一特大型含氦—富氦天然气田。东胜气田氦气属于典型的壳源氦,来源于基底的太古界—元古界变质岩—花岗岩系,富集与燕山期以来的岩浆侵入、断裂活动有关。东胜气田具备有利的氦气成藏地质条件,伴生氦气与烃类气具有异源同储成藏特征,剖析其成藏主控因素为: 基底富U、Th岩石发育是基础,断裂活动是核心,储盖圈保条件是必备,时空配置是关键,其中早白垩世是最重要的一期构造—岩浆热事件,深源岩浆活动导致的深部物质和热能的大规模上涌是中生代流体成藏(矿)的有利地球动力学背景,控制了鄂尔多斯盆地石炭系—二叠系煤系烃源岩大规模生气。断裂活动和圈闭形成与上古生界天然气、氦气聚集成藏具有良好的时空配置关系,与华北克拉通破坏过程耦合。鄂尔多斯地块在早白垩世至中新世深部热流体对盆地发生的多期岩浆活动、基底断裂活化及浅部断裂活动具有明显的控制作用,同时也对石炭系—二叠系煤系烃源岩成烃成藏具有重要的控制作用。  相似文献   

确定区域大地水准面的K-means-RBF神经网络方法     

黄子炎  王庆宾  冯进凯  谭勖立  范雕  黄炎 《测绘科学技术学报》2021,38(3):246-252

确定区域大地水准面的几何水准方法在拟合大地水面时未顾及重力场信息,仅是一种单纯的数学拟合,忽略了重力场数据自身的物理性和不同数据间的相关性.近年来,深度学习方法得到广泛重视与研究.本文提出了一种有监督学习的RBF神经网络精化大地水准面的方法,使用包含重力异常和大地水准面高的重力场数据进行神经网络训练,并采用K-means聚类算法为RBF神经网络的径向基函数进行初始化,提高神经网络的收敛速度和精度.实验结果表明,该方法确定的平原、丘陵和山地复杂实验区域大地水准面高标准差分别为0.044、0.159和1.075 cm,优于使用几何水准直接拟合大地水准面高的精度,且在重力异常中加入蒙特卡罗随机噪声模拟的观测误差后,3类实验区域标准差总体仍在cm级,误差增幅不显著,表明该方法在确定大地水准面时,能够抑制观测误差的影响.  相似文献   

Effects of different spatial distributions of physical soil crusts on runoff and erosion on the Loess Plateau in China   总被引：1，自引：0，他引：1       下载免费PDF全文

Pei Lu  Xinli Xie  Linhua Wang  Faqi Wu 《地球表面变化过程与地形》2017,42(13):2082-2089

The response of runoff and erosion to soil crusts has been extensively investigated in recent decades. However, there have been few attempts to look at the effects of spatial configuration of different soil crusts on erosion processes. Here we investigated the effects of different spatial distributions of physical soil crusts on runoff and erosion in the semi‐arid Loess Plateau region. Soil boxes (1.5 m long × 0.2 m wide) were set to a slope of 17.6% (10°) and simulated rainfall of 120 mm h^?1 (60 minutes). The runoff generation and erosion rates were determined for three crust area ratios (depositional crust for 20%, 33%, and 50% of the total slope) and five spatial distribution patterns (depositional crust on the lower, lower‐middle, middle, mid‐upper, and upper slope) of soil crusts. The reduction in sediment loss (‘sediment reduction’) was calculated to evaluate the effects of different spatial distributions of soil crusts on erosion. Sediment yield was influenced by the area ratio and spatial position of different soil crusts. The runoff rate reached a steady state after an initial trend of unsteadily increasing with increasing rainfall duration. Sediment yield was controlled by detachment limitation and then transport limitation under rainfall. The shifting time of erosion from a transport to detachment‐limiting regime decreased with increasing area of depositional crust. No significant differences were observed in the total runoff among treatments, while the total sediment yield varied under different spatial distributions. At the same area ratio, total sediment yield was the largest when the depositional crust was on the upper slope, and it was smallest when the crust was deposited on the lower slope. The sediment reduction of structural crust (42.5–66.5%) was greater than that of depositional crust (16.7–34.3%). These results provide a mechanistic understanding of how different spatial distributions of soil crusts affect runoff and sediment production. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

Exploring the interaction of surface roughness and slope gradient in controlling rates of soil loss from sloping farmland on the Loess Plateau of China     

Taotao Li  Longshan Zhao  Hongteng Duan  Yifan Yang  Yu Wang  Faqi Wu 《水文研究》2020,34(2):339-354

Surface roughness and slope gradient are two important factors influencing soil erosion. The objective of this study was to investigate the interaction of surface roughness and slope gradient in controlling soil loss from sloping farmland due to water erosion on the Loess Plateau, China. Following the surface features of sloping farmland in the plateau region, we manually prepared rough surfaces using four tillage practices (contour drilling, artificial digging, manual hoeing, and contour plowing), with a smooth surface as the control measure. Five slope gradients (3°, 5°, 10°, 15°, and 20°) and two rainfall intensities (60 and 90 mm/hr) were considered in the artificial rainfall simulation experiment. The results showed that the runoff volume and sediment yield increased with increasing slope gradient under the same tillage treatment. At gentle slope gradients (e.g., 3° and 5°), the increase in surface roughness prevented the runoff and sediment production, that is, the surface roughness reduced the positive effect of slope gradient on the runoff volume and sediment yield to a certain extent. At steep slope gradients, however, the enhancing effect of slope gradient on soil erosion gradually increased and surpassed the reduction effect of surface roughness. This study reveals the existence of a critical slope gradient that influences the interaction of surface roughness and slope gradient in controlling soil erosion on sloping farmland. If the slope gradient is equal to or less than the critical value, an increase in surface roughness would decrease soil erosion. Otherwise, the increase in surface roughness would be ineffective for preventing soil erosion. The critical slope gradient would be smaller under higher rainfall intensity. These findings are helpful for us to understand the process of soil erosion and relevant for supporting soil and water conservation in the Loess Plateau region of China.  相似文献   

利用多元回归分析反演西南印度洋区域海底地形     

范雕  李姗姗  杨军军  孟书宇  邢志斌  张驰  冯进凯 《测绘学报》2020,49(2):147-161

针对海底地形与重力异常和重力异常垂直梯度在相应频段呈现强线性相关的特点,引入多元回归分析技术,提出并详细推导了联合多元重力数据的海底地形建模方法。然后,在西南印度洋SWIR(Southwest India Ridge)所在部分海域开展了海底地形反演试验及地形地貌分析研究。试验结果表明:6种海深模型中,基于多元回归分析技术构建的海深模型(BDVG模型)检核精度最高,相较于S&S V18.1模型和ETOPO1模型精度分别提高了11.51%和57.81%左右;2000 m以上水深海域,各个海深模型的检核精度较高,相对误差波动较小,反映了深海海域具有良好的反演效果;地形起伏剧烈海域或者浅海海域,BDVG海深模型,相较于以重力异常和重力异常垂直梯度作为单一输入源建立的BDG模型和BVGG模型相对误差及相对误差波动变化较小,反映了BDVG模型拥有更好的稳定性,从而体现了联合反演的必要性和优势。Indomed FZ—Gallieni FZ上唯一轴部缺失裂谷洋脊段(27洋脊段)目前属于岩浆供应充足阶段,构造作用的海底扩张对其影响较小;同时由于对称裂离方式影响,27洋脊段沿轴南北对称分布有地形隆起。  相似文献   

大地水准面高的计算及其在海底地形反演中的应用     

范雕  李姗姗  苏明晓  孟书宇  邢志斌  张驰  冯进凯 《海洋技术学报》2019,38(5)

为充分挖掘海洋重力数据在反演海底地形中的应用潜力,尝试探索利用大地水准面高反演海底地形的技术途径,并以夏威夷—皇帝海山链拐点所在海区作为反演试验区进行验证。首先采用Belikov列推法计算伴随(缔和)勒让德函数,利用EIGEN-6C4地球重力场模型解算获取了分辨率为1'的大地水准面高格网数值模型;然后通过综合分析反演比例函数和转换函数特点、研究海区大地水准面高与海底地形的相干特性以及大地水准面高本身尺度特征,获得了利用大地水准面高反演海底地形的频段范围;最终以试验海区大地水准面高为数据输入,构建了相应的海底地形模型(BNT模型),并与ETOPO1等海深模型进行比对分析。试验结果表明:BNT模型检核差值在一倍均方差范围检核点数量占比70.60%,相比正态分布更加集中;BNT模型检核精度低于ETOPO1等海深模型;海深模型检核精度随着水深增加不断提升,水深小于1 000 m时,海深模型相对误差出现较大发散现象;计算海域ETOPO1模型精度最高,GEBCO模型和DTU10模型检核精度相当。  相似文献   

Experimental Investigation About Influence of Pre-existing Fracture on Hydraulic Fracture Propagation Under Tri-axial Stresses     

Wan Cheng  Yan Jin  Qing Lin  Mian Chen  Yakun Zhang  Ce Diao  Bing Hou 《Geotechnical and Geological Engineering》2015,33(3):467-473

  相似文献   

Rupture model of the 2013 M_W 6.6 Lushan (China) earthquake constrained by a new GPS data set and its effects on potential seismic hazard          下载免费PDF全文

Rumeng Guo  Yong Zheng  Faqi Diao  Xiong Xiong  Jiao Xu 《地震科学（英文版）》2018,31(3):117-125

Vertical records are critically important when determining the rupture model of an earthquake, especially a thrust earthquake. Due to the relatively low fitness level of near-field vertical displacements, the precision of previous rupture models is relatively low, and the seismic hazard evaluated thereafter should be further updated. In this study, we applied three-component displacement records from GPS stations in and around the source region of the 2013 MW6.6 Lushan earthquake to re-investigate the rupture model.To improve the resolution of the rupture model, records from both continuous and campaign GPS stations were gathered, and secular deformations of the GPS movements were removed from the records of the campaign stations to ensure their reliability. The rupture model was derived by the steepest descent method(SDM), which is based on a layered velocity structure. The peak slip value was about 0.75 m, with a seismic moment release of 9.89 × 10~(18) N·m, which was equivalent to an M_W6.6 event. The inferred fault geometry coincided well with the aftershock distribution of the Lushan earthquake. Unlike previous rupture models, a secondary slip asperity existed at a shallow depth and even touched the ground surface. Based on the distribution of the co-seismic ruptures of the Lushan and Wenchuan earthquakes, post-seismic relaxation of the Wenchuan earthquake, and tectonic loading process, we proposed that the seismic hazard is quite high and still needs special attention in the seismic gap between the two earthquakes.  相似文献