Results from microseismic monitoring,conventional instrumentation,and tomography surveys in the creation and thinning of a burst-prone sill pillar |
| |
| Authors: | Richard McCreary John McGaughey Yves Potvin Dave Ecobichon Marty Hudyma Harald Kanduth Alain Coulombe |
| |
| Institution: | (1) Noranda Technology Centre, Pointe-Claire, Québec, Canada;(2) Present address: Geco Division, Noranda Minerals Inc, Manitouwadge, Ontario, Canada;(3) Present address: Mining Division, Brunswick Mining & Smelting Corp. Ltd., Bathurst, New Brunswick, Canada;(4) Minnova Inc, Chapais, Québec, Canada |
| |
| Abstract: | Located in northern Québec, the Lac Shortt Mine was a small gold mine consisting of a thin subvertical orebody which was mined in three main phases. High stress and rockbursting conditions were experienced when ore was extracted in the upper zone between the surface and a depth of 500 metres during the first two phases of mining. Severe rockbursts were experienced in late 1989 near the shaft and in the footwall development following a deepening of the mine shaft to a depth of 830 m and partial development of footwall drift access for the third phase of mining (the mining of the lower zone starting at a depth of 830 m moving upward toward a depth of 500 m). A 16-channel Electrolab MP250 microseismic system, with a Queen's University Full-Waveform  piggy-back system, was installed underground at the site due to these problems.It was expected that the thinning sill would be subjected to an ever-increasing load as the thickness of the 500 m sill pillar decreased in the face of the mining excavation from below. A monitoring program consisting of the microseismic monitoring system, a range of conventional geomechanics monitoring tools as well as the undertaking of periodic seismic tomography surveys to assess the ongoing state of stress and rock mass condition within the sill was therefore warranted.The anomalously high-magnitude stress field and the brittle rockmass created a situation in which rockmass failure was common and violent. In the creation and thinning of the sill pillar, the location of banded microseismic activity was crucial in tracing rockmass failure and the associated ground control problems. Reliable source-location determination enabled the identification of areas of stress increase. The movement of the rockmass failure front could be followed, and was responsible for stope dilution, footwall and orebody development deterioration, and caving.Source-mechanism analyses gave accurate double-couple solutions for approximately forty percent of these events having at least ten recognizable polarities. Results suggested movement along vertical north-south striking or vertical east-west striking features. Underground observation of damaged access points showed that vertical north-south striking joints were experiencing failure.The microseismic activity, which was consistently concentrated close to the southwest and northeast corners of current production stopes, could be explained by a stress field oriented obliquely to the strike of the orebody, as measured prior to shrinkage of the sill pillar byin situ stress measurements and observed borehole overbreaks. The orientations of theP andT axes for the microseismic activity further confirmed that the stress field oriented obliquely to strike.While an increase in compressional-wave velocity of 2.3 percent, corresponding to a measured stress increase of approximately 10 MPa could be measured by repeated tomographic surveys, it was relatively small and only a factor of two or so above the velocity measured uncertainty. The relative insensitivity of thein situ rock mass modulus to the applied stress is believed to be largely due to the rockmass discontinuities being relatively closed prior to stress increase, as substantiated by the small deformations seen by the extensometer and borehole camera. This situation existed because of the very high pre-mining stress level.The experimental demonstration that the rock could not absorb substantially increased load through the mechanism of discontinuity closure or tightening (which would be reflected in the modulus) may be evidence in itself of potentially burst-prone ground, such as encountered at Lac Shortt. |
| |
| Keywords: | Rockburst microseismic geomechanics tomography stress cell borehole slotter extensometer seismicity anisotropy crosshole full-waveform sill pillar source mechanism double-couple dilution |
| 本文献已被 SpringerLink 等数据库收录！ |
|
