共查询到20条相似文献，搜索用时 806 毫秒
1.
海鱼AChE监测海水有机磷农药的可行性研究 总被引：10，自引：0，他引：10
有机磷农药(OPs)对乙酰胆碱酯酶(AChE EC 3.1.1.7)具有专一性抑制作用,因此AChE常作为淡水和土壤OPs污染的特异性标识物(biomarker).本文在海水背景下,通过测定两种有机磷农药(马拉硫磷和甲基对硫磷)对海洋鱼类-鲈鱼[Lateolabrax japonicus(cuvier)]脑组织AChE的抑制效应,分析了海鱼AChE监测海水OPs的可行性.结果显示,抑制时间为20min时,抑制程度达到相对稳定;在低浓度OPs抑制下,纯酶液比粗酶液表现出更好的敏感性,对马拉硫磷和甲基对硫磷的灵敏度分别达到0.28μg*L-1和0.2μg*L-1;在一定浓度范围内,AChE活力对OPs具有显著的线性响应.研究表明,利用鲈鱼AChE指示和监测海水OPs的微污染是完全可行的. 相似文献
2.
基于FIA和光学原理的酶传感器检测海水甲基对硫磷 总被引：2，自引：0，他引：2
将乙酰胆碱酯酶(acetylcholinesterase,AChE)传感器与流动注射系统(flow injection analysis system,FIA)相结合,通过光学方法测定固定化酶受农药抑制后的残余活性,对海水中微量甲基对硫磷进行定量分析。该系统的适宜工作条件为:温度30℃;固定化酶的用量0.05 U;载液流速0.45 mL/min;进样时间20 min;底物(碘化硫代乙酰胆碱)溶液浓度0.100 mol/L,注射量100μL。在0.1~100μg/L之间,农药浓度的对数值与固定化酶活性的抑制率之间具有良好的线性关系(r=0.995 3)。利用该系统检测含甲基对硫磷分别为0.8μg/L和5.0μg/L的模拟海水样品,获得了较好的准确度和精密度,平均相对误差和变异系数均小于10%。 相似文献
3.
4.
5.
6.
为实现海水中有机磷浓度现场监测,采用由单片机和工控机组成的海水有机磷农药实时数据采集系统的设计.给出了由PIC单片机构成的采集控制模块硬件设计原理和软件设计方法,工控机的程序流程和浓度的算法. 相似文献
7.
沙滩水体中溶解性石油烃的降解及吸附研究 总被引：2，自引：0，他引：2
以海水体系和海水-砂体系作为对比,研究了沙滩水体中溶解性石油烃的降解及吸附作用。实验结果表明,1d内海水中石油浓度的降低主要是由于砂的快速吸附作用,3d以后生物对石油烃的降解作用逐渐占据优势。两种体系中降烃菌数量及石油浓度的变化曲线表明,砂对油的快速吸附显著降低了海水中石油污染物的浓度,使得海水含砂体系中石油降解菌的数量远高于海水体系。海水中石油污染物的降解符合一级动力学模式,当含砂体系中砂的粒径不同时,石油污染物降解的半衰期可由海水体系的31.9d缩短到22.4d和19.5d。系统中砂的存在有利于海水中石油污染物的去除,有约20%的石油污染物被吸附到砂上,然而这种去除是物理去除。 相似文献
8.
采用化学裂解和酶解相结合的方法，进行了深海沉积物中微量DNA的提取，并采用DNA吸附树脂进行纯化。结果表明，该方法能有效地去除沉积物中的腐殖酸等抑制剂，每克湿重沉积物样品可得到DNA约16μg，回收率可达95％，所得到的DNA分子片段均在23kb左右，纯化后的DNA可直接应用于各种分子生物学操作。利用细菌16SrDNA通用引物对所提取的深海沉积物DNA进行了PCR—RRJ及系统发育分析，各主要细菌类群均能检出，证实该方法可以应用于深海等极端环境中微生物的多样性调查、系统发育分析以及特殊功能基因的筛选，同时还可应用于环境样品中生物量的半定量估计。 相似文献
9.
金枪鱼(Katsuwonus pelamis)碎肉蛋白降压肽的酶解制备及活性研究 总被引：2，自引：0，他引：2
以血管紧张素转换酶(ACE)抑制率为指标,通过正交试验L9(34)确定碱性蛋白酶(Alcalase)对金枪鱼(Katsuwonus pelamis)碎肉蛋白的最佳酶解条件,利用D101大孔树脂建立了酶解物的脱盐工艺,利用超滤、葡聚糖凝胶(G-25)色谱和反相-高效液相色谱(RP-HPLC)分离降压肽,并确定其纯度,利用氨基酸序列分析和ESI-MS鉴定纯化多肽的结构。结果表明,碱性蛋白酶酶解金枪鱼碎肉蛋白制备降压肽的最佳酶解条件是:pH 9.5,酶用量1.5%,酶解温度50°C,酶解时间5h;D101大孔吸附树脂脱盐工艺条件为:上样浓度10 mg/mL、上样流速1.5 BV/h、解吸剂为75%乙醇;酶解物经超滤和Sephadex G-25分离获得一个纯度较高的四肽,经氨基酸序列分析和ESI-MS鉴定结构为Phe-GlyGly-Val(FGGV),ESI-MS检测给出分子离子峰m/z 379.50([M+H]+)。利用碱性蛋白酶酶解并经超滤和色谱技术制备的金枪鱼碎肉蛋白降压肽具有良好的ACE抑制活性,可作为降压药物、保健食品或添加剂进行开发。 相似文献
10.
根据2009-04—2010-02隔月6个航次桑沟湾9个调查站位贝类养殖区有机氯(OCPs)、有机磷(OPPs)农药残留和麻痹性贝毒(PSP)的调查资料,分析了它们在该海域海水中、表层沉积物中和主要贝类(栉孔扇贝、太平洋牡蛎和菲律滨蛤仔)体内的含量水平,就农药残留及贝毒污染对海洋环境质量的影响进行综合评价和类别划分,并对主要食用贝类中农药残留和贝毒的暴露水平进行健康风险评估。结果表明,桑沟湾贝类养殖区海水质量、沉积物质量和养殖贝类质量水平范围为1~2级,平均分别为2级、1级和1级,养殖生态环境综合质量水平为2级;总体上,该海域海洋环境综合质量处于良好水平,贝类产区生态环境质量为1类区(清洁区)。即该海域农药残留及贝毒污染对海洋环境质量影响较小或无明显影响。另外,针对食用桑沟湾贝类水产品的消费人群进行了农药残留及贝毒污染的健康风险评估,结果表明调查人群食用贝类中OCPs中的HCHs和DDTs、OPPs中的马拉硫磷和甲基对硫磷、PSP的日摄入量分别为0.75,2.11,0.19,0.09和1.22μg/(人·d),其摄入量低于ADI的推荐限值,因此桑沟湾主要食用贝类中农药残留及贝毒污染的健康风险处于安全范围。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
20.