共查询到18条相似文献，搜索用时 312 毫秒
1.
2.
水饱和孔隙介质中平面震电波电磁特性的定量模拟 总被引：1，自引：0，他引：1
震电效应在地球物理测井和勘探领域拥有十分广阔的前景.为了研究孔隙介质中的震电效应,本文基于毛管模型中渗流场和电流场耦合理论,利用Pride震电理论对震电耦合波传播特性进行了定量模拟;对震电横波、震电快纵波、震电慢纵波的传播速度、衰减常数、电场强度、电流密度以及电荷密度进行了比较,定量分析了其随孔隙度、离子浓度、阳离子交换量的变化规律.分析结果表明:随着频率增大,三种震电耦合波波速、衰减常数以及电流密度与固相速度比值的模值增大,震电横波电场强度与固相速度比值的模值减小,震电快纵波、慢纵波电场模值增大.当频率相同时,震电快纵波波速最大、衰减常数最小,震电慢纵波波速最慢、衰减常数最大,震电横波的波速和衰减常数大小居于快、慢纵波之间;频率不变时,震电慢纵波电场强度与固相速度比值的模值最大,快纵波次之,横波最小;中低频时,震电横波电流密度与固相速度比值的模值略大于慢纵波;高频时,震电慢纵波略大于横波,快纵波一直最小.溶液浓度和阳离子交换量对三种震电波的波速和衰减常数影响很小;溶液浓度越大或阳离子交换量越小,三种震电波电场强度、电流密度与固相速度比值的模值越小,震电快纵波和慢纵波电荷密度与固相速度比值的模值也越小,但是相位几乎都不变. 相似文献
3.
为了研究气枪激发信号的波场,本文利用谱元法对双相介质中波的传播做了数值模拟,分析了波的传播特征.本文主要做了以下工作:(1)研究了使用谱无法(SEM)模拟孔隙弹性介质中波的传播,模拟结果表明,采用谱元法能有效解决双相介质的波场传播模拟问题.(2)验证了Biot理论中慢纵波的存在.双相介质中存在明显的慢纵波,流相波场的慢... 相似文献
4.
本文基于Biot理论,推导出Zoeppritz形式的双相介质分界面上弹性波的反射与透射公式,对单相Zoeppritz公式与双相反射系数公式进行了比较,对双相介质含油、水、气不同流体时的反射规律以及孔隙度、渗透率、饱和度等储层参数对纵波反射的影响进行了研究.数值模拟分析表明,双相与单相反射公式的主要差异在于双相介质反射公式中考虑了液相、固液耦合相弹性模量的影响;油砂、水砂、气砂岩的慢P波反射差异明显;快P波反射对孔隙度的变化敏感,饱和度次之,对渗透率和频率的变化不敏感. 相似文献
5.
复电阻率测井在识别油水层的能力上优于常规电阻率测井,然而储层岩石复电阻率特性的微观机理还没有统一完整的解释和数学模拟方法,致使复电阻率测井技术的开发缺乏足够的理论基础.本文基于孔隙介质Pride电震耦合理论,结合谐变信号激励下渗流场与电流场的耦合理论,推导出一级近似条件下的Pride电震耦合理论.采用格林函数方法建立了一维电震波场的波动方程及其解.构造了双电极法测量储层岩石复电阻率的物理模型和数学模型,从理论上阐明了岩石复电阻率频散特性的微观机制与电震效应的关系,定量分析了储层岩石复电阻率频散特性的影响因素.数学模拟结果表明:储层岩石复电阻率的频散现象是在电震快纵波和电震慢纵波的共同作用下,由孔隙介质中的电渗流机制形成的;储层岩石的复电阻率随孔隙度的增大而减小,随渗透率的增大而增大,地层水矿化度的增加或阳离子交换量的增大使得同频率的复电阻率减小.慢纵波界面极化频率受孔隙度、渗透率和地层弹性模量的影响较大,而快纵波界面极化频率受地层弹性模量的影响较大. 相似文献
6.
人造砂岩具有参数可控特点,可广泛的应用于物理模拟及实验研究领域,文章介绍了压制法制作人造砂岩的基本流程.对人造砂岩物理参数及声学性质进行实验研究.测量了密度、孔隙度等参数,给出压制压力与密度、纵波速度关系图.利用超声波透射法测量人造砂岩纵横波速度,对人工砂岩在饱含气与饱含水状态下速度变化进行定量分析,给出纵横波速度随孔隙度变化曲线.饱含气状态变化到饱含水状态后,纵波速度上升,横波速度下降.利用Gassmann方程对流体替换后速度进行预测,实际测试数据的纵波速度与预测计算数据比较吻合.纵横波速度变化规律与天然砂岩基本一致. 相似文献
7.
当地下介质存在各向异性时,在观测坐标系下的弹性参数与自然坐标系下的弹性参数不一定相同．首先,根据势能密度和耗散能密度与坐标轴无关的原理,推导出了双相各向异性介质中观测坐标系下弹性参数与自然坐标系下弹性参数之间的关系;然后,从任意双相各向异性中弹性波波动方程出发,得出了该方程的伪谱法数值解法;最后,通过数值模拟,观测到了存在于双相各向异性介质中的４类波,即快纵波、慢纵波、快横波和慢横波．在双相各向异性介质中,ＳＶ波传播的波前面上仍然存在波面尖角,这些尖角在界面上要发生反射和透射．另外,数值模拟结果中可见转换慢纵波和慢纵波的转换波． 相似文献
8.
波场在含流体的孔隙介质中传播时会产生频散和衰减现象.波场的频散和衰减与孔隙介质的岩石物理属性有关,包括孔隙度、渗透率、流体属性等.现有的三维裂缝/软孔隙网络模型利用椭圆截面纵横比的变化模拟从扁裂缝、软孔隙到硬孔隙的多种情况,而未考虑同时包含孔隙和裂缝的全局性网络空间.为了更好地描述裂缝-孔隙空间,本文提出同时包含裂缝和孔隙的三维裂缝-孔隙网络模型,并给出渗透率的计算方法.通过体积平均法推导了三维裂缝/软孔隙网络模型和三维裂缝-孔隙网络模型的波动方程,利用平面波分析方法得到纵波频散/衰减曲线的表达式,同时应用数值模拟研究了总孔隙度、裂缝孔隙度、裂缝纵横比、裂缝数密度、孔隙流体黏度对纵波衰减和速度频散特征的影响.结果表明,在三维裂缝-孔隙网络模型下,总孔隙度、裂缝参数等对纵波频散衰减特征的影响与三维裂缝/软孔隙网络模型相似.具体表现为:纵波在高频段内出现频散和衰减现象.孔隙度的变化主要影响逆品质因子曲线峰值的大小;裂缝数密度主要控制速度显著变化的范围;裂缝纵横比对纵波速度和特征频率有显著影响. 相似文献
9.
10.
深层-超深层油气地震勘探涉及高温介质地震波传播问题,热弹介质参数对地震波传播有重要影响.含弛豫时间修正项的Lord-Shulman双曲型耦合热弹波动方程从理论上预测了热弹性介质中存在快纵波、慢纵波(一种准静态慢纵波,简称热波)和横波的传播,两个纵波为热耗散衰减波而横波不受介质热特性的影响.本文结合平面波频散分析和格林函数法数值模拟,详细研究两个热耗散衰减波的频散和衰减特征,着重分析热导率、热膨胀系数及比热的变化对波速和衰减的影响.研究表明热导率作为主要参数决定了波速与衰减的临界变化,热膨胀系数对波速和衰减的幅度有明显影响,比热则兼顾了前两个热弹系数的影响特征.最后,利用热弹性动力学频率域的二阶格林函数进行波场快照数值模拟,展示热弹性介质中纵波、横波和热波的传播行为. 相似文献
11.
裂缝诱导HTI双孔隙介质模型是将一组垂直排列的裂缝系统嵌入到统计各向同性的孔隙岩石基质系统中而建立的.为了研究裂缝参数对地震波在该模型中传播规律的影响,本文分别对裂缝弱度、裂缝孔隙度和裂缝渗透率这三个主要的裂缝参数进行了分析研究.数值结果表明,裂缝诱导HTI双孔隙介质中,裂缝弱度越大,介质的各向异性强度越强;与基质孔隙系统相比,裂缝系统孔隙度对介质等效孔隙度的影响很小,而裂缝系统渗透率的增大则将显著提高介质在裂缝发育方向上的等效渗透率,这符合对裂缝系统"低孔"、"高渗"特性的认识.此外,裂缝系统渗透率的增大也使慢纵波的振幅显著增强. 相似文献
12.
对华北地区韧性剪切带几种代表上、中、下地壳深度的糜棱岩及其围岩在高温高压条件下进行纵波速度测定及各向异性研究．对实验样品的纵波速度测定得到以下结果：１．沿糜棱岩面理方向的纵波速度大于与面理垂直方向的纵波速度，差值为０．１５-０．３０ｋｍ／ｓ，各向异性为３％-５％；２．糜棱岩的纵波速度低于其围岩的纵波速度，差值为０．１０-０．４５ｋｍ／ｓ；３．中地壳角闪岩相糜棱岩的纵波速度各向异性高于上地壳绿片岩相糜棱岩和下地壳麻粒岩相糜棱岩的各向异性；４．地震波速各向异性与糜棱岩矿物优选定向有关． 相似文献
13.
The 3D shear experiment over the Natih field in Oman: the effect of fracture-filling fluids on shear propagation 总被引：1，自引：0，他引：1
This is the final paper in a series on the 3D multicomponent seismic experiment in Oman. In this experiment a 3D data set was acquired using three-component geophones and with three source orientations. The data set will subsequently be referred to as the Natih 9C3D data set. We present, for the first time, evidence demonstrating that shear waves are sensitive to fluid type in fractured media. Two observations are examined from the Natih 9C3D data where regions of gas are characterized by slow shear-wave velocities. One is that the shear-wave splitting map of the Natih reservoir exhibits much larger splitting values over the gas cap on the reservoir. This increase in splitting results from a decrease in the slow shear-wave velocity which senses both the fractures and the fracture-filling fluid. Using a new effective-medium model, it was possible to generate a splitting map for the reservoir that is corrected for this fluid effect. Secondly, an anomaly was encountered on the shear-wave data directly above the reservoir. The thick Fiqa shale overburden exhibits a low shear-wave velocity anomaly that is accompanied by higher shear reflectivity and lower frequency content. No such effects are evident in the conventional P-wave data. This feature is interpreted as a gas chimney above the reservoir, a conclusion supported by both effective-medium modelling and the geology.
With this new effective-medium model, we show that introduction of gas into vertically fractured rock appears to decrease the velocity of shear waves (S2), polarized perpendicular to the fracture orientation, whilst leaving the vertical compressional-wave velocity largely unaffected. This conclusion has direct implications for seismic methods in exploration, appraisal and development of fractured reservoirs and suggests that here we should be utilizing S-wave data, as well as the conventional P-wave data, as a direct hydrocarbon indicator. 相似文献
With this new effective-medium model, we show that introduction of gas into vertically fractured rock appears to decrease the velocity of shear waves (S2), polarized perpendicular to the fracture orientation, whilst leaving the vertical compressional-wave velocity largely unaffected. This conclusion has direct implications for seismic methods in exploration, appraisal and development of fractured reservoirs and suggests that here we should be utilizing S-wave data, as well as the conventional P-wave data, as a direct hydrocarbon indicator. 相似文献
14.
Viscoelastic modelling reveals that the interaction of compressional-wave velocity Cp, compressional-wave quality factor Qp, shear-wave velocity Cs, shear-wave quality factor Qs and Poisson's ratio as a function of time intercept τ and ray parameter p, is complicated; however, distinct, potentially diagnostic behaviours are seen for different combinations of viscoelastic parameters. Synthetic seismograms for three viscoelastic reservoir models show that variations in the Poisson's ratio produce visible differences when compared to the corresponding elastic synthetic seismograms; these differences are attributable to interaction of the elastic parameters with Qp and Qs. When the P-wave acoustic impedance contrast is small, viscoelastic effects become more apparent and more useful for interpretation purposes. The corresponding amplitude and net phase spectra reveal significant differences between the elastic and the viscoelastic responses. When P-wave reflectivities are large, they tend to dominate the total response and to mask the Q reflectivity effects. The attenuation effects are manifested as an amplitude decay that increases with both time and ray parameter. The sensitivity of the computed seismic responses for various combinations of viscoelastic parameters suggests the opportunity for diagnostic interpretation of τ-p seismic data. The interpretation of the viscoelastic parameters can permit a better understanding of the rock types and pore fluid distribution existing in the subsurface. 相似文献
15.
地震波本征衰减反映了地层及其所含流体的一些特性,对油气勘探开发有重要意义.已有的理论研究与实验发现,地震频带内的衰减主要与中观尺度(波长与颗粒尺度之间)的斑状部分饱和、完全饱和岩石弹性非均匀性情况下波诱导的局部流体流有关.这种衰减与岩石骨架、孔隙度及充填流体的性质密切相关.本文着重讨论均匀流体分布、斑状或非均匀流体分布两种情况下部分饱和岩石的纵波模量差异.以经典岩石物理理论和衰减机制认识为基础,通过分析低频松弛状态、高频非松弛状态岩石的弹性模量,讨论储层参数(如孔隙度、泥质含量以及含水饱和度等)与纵波衰减之间的确定性关系.上述方法与模型在陆相砂泥岩地层与海相碳酸盐岩地层中的适用性通过常规测井资料得到了初步验证. 相似文献
16.
17.
The clay-sand mixture model of Xu and White is shown to simulate observed relationships between S-wave velocity (or transit time), porosity and clay content. In general, neither S-wave velocity nor S-wave transit time is a linear function of porosity and clay content. For practical purposes, clay content is approximated by shale volume in well-log applications. In principle, the model can predict S-wave velocity from lithology and any pair of P-wave velocity, porosity and shale volume. Although the predictions should be the same if all measurements are error free, comparison of predictions with laboratory and logging measurements show that predictions using P-wave velocity are the most reliable. The robust relationship between S- and P-wave velocities is due to the fact that both are similarly affected by porosity, clay content and lithology. Moreover, errors in the measured P-wave velocity are normally smaller than those in porosity and shale volume, both of which are subject to errors introduced by imperfect models and imperfect parameters when estimated from logs. Because the model evaluates the bulk and shear moduli of the dry rock frame by a combination of Kuster and Toksöz’ theory and differential effective medium theory, using pore aspect ratios to characterize the compliances of the sand and clay components, the relationship between P- and S-wave velocities is explicit and consistent. Consequently the model sidesteps problems and assumptions that arise from the lack of knowledge of these moduli when applying Gassmann's theory to this relationship, making it a very flexible tool for investigating how the vP-vs relationship is affected by lithology, porosity, clay content and water saturation. Numerical results from the model are confirmed by laboratory and logging data and demonstrate, for example, how the presence of gas has a more pronounced effect on P-wave velocity in shaly sands than in less compliant cleaner sandstones. 相似文献
18.
Shear-wave velocity logs are useful for various seismic interpretation applications, including bright spot analyses, amplitude-versus-offset analyses and multicomponent seismic interpretations. Measured shear-wave velocity logs are, however, often unavailable. We developed a general method to predict shear-wave velocity in porous rocks. If reliable compressional-wave velocity, lithology, porosity and water saturation data are available, the precision and accuracy of shear-wave velocity prediction are 9% and 3%, respectively. The success of our method depends on: (1) robust relationships between compressional- and shear-wave velocities for water-saturated, pure, porous lithologies; (2) nearly linear mixing laws for solid rock constituents; (3) first-order applicability of the Biot–Gassmann theory to real rocks. We verified these concepts with laboratory measurements and full waveform sonic logs. Shear-wave velocities estimated by our method can improve formation evaluation. Our method has been successfully tested with data from several locations. 相似文献