共查询到20条相似文献，搜索用时 62 毫秒
1.
海洋的盐度观测对于气候和海洋科学的研究有重要的意义,盐度的卫星遥感观测需要估计各种因素带来的误差影响。本文基于海面微波辐射理论和海水相对电容率等模型,采用蒙特卡洛模拟方法研究了在盐度遥感中温度误差、仪器误差以及风速误差对于后续的盐度反演的影响。通过计算温度误差产生的盐度误差,并与敏感性方法的对比发现,在低温低盐时温度误差对盐度反演误差的影响较大,2种方法的偏差较大;而在高温高盐时温度误差对盐度反演误差的影响较小,2种方法的偏差较小。辐射计仪器噪声对盐度误差的影响普遍在0.1psu以上,在低温低盐时可达0.5psu以上。风速误差对盐度反演误差的影响在水平极化状态下随入射角增大,在温度低于20℃时普遍超过1psu;在垂直极化状态下随入射角先减小后增大,在温度低于20℃以及较小的入射角下误差也会超过1psu。对误差的综合分析发现,采用垂直极化状态在高温时这2种误差的影响较小。研究发现,当入射角是45.6°和垂直极化状态下,对于3种典型海面状态(35℃和35psu,20℃和35psu,5℃和30psu),反演的盐度反演误差可达到0.162,0.153和0.444psu,达到了卫星单次扫描对盐度反演的误差要求。 相似文献
2.
3.
《中国海洋大学学报(自然科学版)》2016,(8)
海表面盐度SSS(Sea Surface Salinity)是研究大洋环流和海洋对全球气候影响的重要参量。海表面盐度卫星遥感探测可以满足大范围、连续观测的研究需要,是获取该参量的有效手段。2009年欧洲空间局发射了SMOS(Soil Moisture and Ocean Salinity)卫星,并且根据卫星观测的数据反演出海表面盐度的相关产品,但是产品的精度还有待于进一步的提高。本文利用多元线性回归的统计分析方法,针对SMOS卫星相关数据(观测亮温数据和辅助数据)建立一种全新的不依赖于物理机制的海表面盐度统计模型。本文针对太平洋中部提出的统计模型计算的盐度点对点的精度为0.165 5psu,1°×1°月平均精度为0.106 3psu,而SMOS卫星Level 2盐度产品的精度分别为0.585 5和0.181 9psu。同时将模型应用到验证数据集,得到了点对点精度为0.224 2psu,进一步说明模型具有很好的适应性和泛化能力。 相似文献
4.
微波辐射计遥感海水盐度的水池实验研究 总被引：1，自引：0，他引：1
通过水池实验研究了L波段微波辐射和盐度的关系,并进行了盐度的反演计算。实验中,先向水池内加入天然海水,然后通过向水池中添加自来水的方式调节降低池内水体的盐度,使盐度从31.67逐步降低到27.48。在此期间,利用微波辐射计观测池内水体的L波段H极化和V极化辐射值以及S波段V极化辐射值,利用CTD观测池内水体的温度和盐度。L波段微波辐射值和根据辐射理论计算出的亮温值具有很好的线性关系。利用最大和最小的2个盐度下的微波辐射值和由辐射理论计算的亮温得到定标公式,将观测的辐射值换算为亮温。最后利用半解析的反演算法反演盐度。本次实验的反演最大误差为2.1,均方差为0.3。 相似文献
5.
海南岛海区（含西沙海域）渔海况速报试验 总被引：1，自引：0，他引：1
利用航空遥感或卫星遥感技术手段，对大面积海域进行观测，采集处理有关海洋环境要素如海水温度，盐度等，然后进行对比分析，判断，为海洋渔业生产提供可靠服务。本文以１９９４年７月海南岛海区的实际飞行试验，清楚地表明，航空遥感或卫星遥感技术在渔业生产领域的广阔应用前景。 相似文献
6.
海表面盐度是研究海洋对全球气候影响以及大洋环流的重要参量之一,而卫星遥感技术是获取海表面盐度数据的最有效方法.目前,L波段的SMOS和Aquarius/SAC-D遥感卫星正在用于探测海表面盐度,并根据卫星观测数据和物理机制反演出海表面盐度的产品.但在某些近陆地区域,由于淡水流入及陆地射频(RFI)等因素影响,卫星反演盐度的产品精度较低.文中利用“东方红2号”科学考察船的实测数据、SMOS卫星数据,首次针对中国南海海域提出了用贝叶斯网络模型计算海表面盐度,并用验证数据集(实测Argo盐度)对模型进行适应性评估.经过计算,模型误差和验证误差分别为0.47 psu和0.45 psu,而相应的SMOS Level 2产品的精度分别为1.90 psu和1.82 psu.此模型为海表面盐度的计算提供了一个新方法. 相似文献
7.
8.
9.
10.
本研究利用国际在轨SSMIS、WindSat、AMSR-E、ASMR2和国产HY-2A微波辐射计多源遥感大气柱水汽含量观测数据,基于最优插值算法,生成了2003-2015年全球海洋每日0.25°高分辨率的大气柱水汽含量多源遥感融合产品,以及2012-2015年未使用HY-2A微波辐射计数据的全球海洋每日0.25°遥感融合产品。利用无线电探空仪水汽含量观测数据,对生成的全球海洋大气柱水汽含量融合产品进行精度检验。结果表明,总体上,13年间均方根误差和标准差小于3 mm,平均偏差小于0.6 mm,平均绝对偏差小于2 mm,相关系数大于0.98;使用HY-2A微波辐射计数据产品会使融合结果的精度出现微小的降低;AMSR2和HY-2A微波辐射计数据的联合使用对于替代AMSR-E数据具有积极意义。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.