共查询到20条相似文献，搜索用时 31 毫秒
1.
本文对龙门山断裂带金河磷矿浅钻岩芯中的三种断层泥开展了低速到高速摩擦滑动的实验研究,并对实验变形样品开展了BET比表面积研究.摩擦实验在干燥和孔隙水压条件下开展,速率范围涵盖20 μm·s-1~1.4 m·s-1.实验结果显示,三种断层泥在干燥条件下的摩擦性质差别不大,但在孔隙水压条件下,三者的中低速摩擦强度与层状硅酸盐矿物的种类而非总含量紧密相关,蒙脱石和伊利石相比绿泥石更能有效地弱化断层.三种断层泥在孔隙水压条件下存在中低速率域的速度强化,暗示着对断层的加速滑动存在一定的阻碍作用.孔隙水压下,黄绿色和灰绿色断层泥的初始动态弱化非常迅速并伴随断层泥层的瞬时扩容,凹凸体急剧加热导致的局部热压作用可能是造成这种力学行为的物理机制.在经历高速滑动之后,三种断层泥在干、湿条件下的BET比表面积都显著降低,暗示着可能发生了颗粒烧结.中低速域内,孔隙水的存在使得断层泥呈现分散式的剪切变形,BET比表面积的增加因此比干燥条件下更加明显.对表面能的估算表明,颗粒磨碎所消耗的能量至多不超过摩擦力做功的8%,暗示着断层作用中颗粒磨碎所占的能量比例较低. 相似文献
2.
5.12汶川地震同震地表破裂带在虹口八角-深溪沟一带主要出露于三叠系须家河组的炭质泥岩中,同震断层泥在颜色、结构上与老断层泥和围岩类似。通过开挖探槽,系统采样,采用粉晶X射线衍射定量分析方法,研究了同震地表破裂带的围岩、断层角砾岩、老断层泥和新断层泥的矿物成分特征。同震断层泥的主要成分为石英和黏土矿物,含微量长石和白云石;断层泥的显著特征为高黏土矿物含量,从同震断层泥、老断层泥、角砾岩到围岩黏土矿物含量依次降低,黏土矿物以伊利石和伊蒙混层为主,含微量绿泥石和高岭石,矿物组成明显比地表破裂带北段同震断层泥简单。不同颜色的同震断层泥成分略有不同,黑色断层泥中伊利石含量明显高于白色断层泥;老断层泥中含有方解石和白云石,而同震断层泥不含方解石,只含微量白云石。同震断层泥中伊蒙混层高含量表明,在本次地震错动中有富含K的流体参与。 相似文献
3.
High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault,located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 Wenchuan earthquake.The ultimate purpose of this study is to reproduce this earthquake by modeling based on measured frictional properties.Dry gouge of about 1 mm in thickness was deformed dry at slip rates of 0.01 to 1.3 m/s and at normal stresses of 0.61 to 3.04 MPa,using a rotary-shear high-... 相似文献
4.
Internal structures and high-velocity frictional properties of a bedding-parallel carbonate fault at Xiaojiaqiao outcrop activated by the 2008 Wenchuan earthquake 
下载免费PDF全文
下载免费PDF全文 Linfeng Hou Shengli Ma Toshihiko Shimamoto Jianye Chen Lu Yao Xiaosong Yang Yuji Okimura 《地震科学（英文版）》2012,25(3):197-217
This paper reports internal structures of a bedding-parallel fault in Permian limestone at Xiaojiaqiao outcrop that was moved by about 0.5 m during the 2008 MW7.9 Wenchuan earthquake. The fault is located about 3 km to the south from the middle part of Yingxiu-Beichuan fault, a major fault in the Longmenshan fault system that was moved during the earthquake. The outcrop is also located at Anxian transfer zone between the northern and central segments of Yingxiu-Beichuan fault where fault system is complex. Thus the fault is an example of subsidiary faults activated by Wenchuan earthquake. The fault has a strike of 243° or N63°E and a dip of 38°NW and is nearly optimally oriented for thrust motion, in contrast to high-angle coseismic faults at most places. Surface outcrop and two shallow drilling studies reveal that the fault zone is several centimeters wide at most and that the coseismic slip zone during Wenchuan earthquake is about 1 mm thick. Fault zone contains foliated cataclasite, fault breccia, black gouge and yellowish gouge. Many clasts of foliated cataclasite and black gouge contained in fault breccia indicate multiple slip events along this fault. But fossils on both sides of fault do not indicate clear age difference and overall displacement along this fault should not be large. We also report results from high-velocity friction experiments conducted on yellowish gouge from the fault zone using a rotary shear low to high-velocity frictional testing apparatus. Dry experiments at normal stresses of 0.4 to 1.8 MPa and at slip rates of 0.08 to 1.35 m/s reveal dramatic slip weakening from the peak friction coefficient of around 0.6 to very low steady-state friction coefficient of 0.1-0.2. Slip weakening parameters of this carbonate fault zone are similar to those of clayey fault gouge from Yingxiu-Beichuan fault at Hongkou outcrop and from Pingxi fault zone. Our experimental result will provide a condition for triggering movement of subsidiary faults or off-fault damage during a large earthquake. 相似文献
5.
THE GEOLOGICAL AND ROCK MECHANICAL DISTINCTION EVIDENCE BETWEEN STICK-SLIP AND CREEP IN HOST ROCK SEGMENTS OF FAULT 下载免费PDF全文
下载免费PDF全文 ZHOU Yong-sheng 《地震地质》2019,41(5):1266-1272
Paleo-seismic and fault activity are hard to distinguish in host rock areas compared with soft sedimentary segments of fault. However, fault frictional experiments could obtain the conditions of stable and unstable slide, as well as the microstructures of fault gouge, which offer some identification marks between stick-slip and creep of fault.
We summarized geological and rock mechanical distinction evidence between stick-slip and creep in host rock segments of fault, and analyzed the physical mechanisms which controlled the behavior of stick-slip and creep. The chemical composition of fault gouge is most important to control stick-slip and creep. Gouge composed by weak minerals, such as clay mineral, has velocity weakening behavior, which causes stable slide of fault. Gouge with rock-forming minerals, such as calcite, quartz, feldspar, pyroxene, has stick-slip behavior under condition of focal depth. To the gouge with same chemical composition, the deformation mechanism controls the frictional slip. It is essential condition to stick slip for brittle fracture companied by dilatation, but creep is controlled by compaction and cataclasis as well as ductile shear with foliation and small fold. However, under fluid conditions, pressure solution which healed the fractures and caused strength recovery of fault, is the original reason of unstable slide, and also resulted in locking of fault with high pore pressure in core of fault zone. Contrast with that, rock-forming minerals altered to phyllosilicates in the gouges by fluid flow through degenerative reaction and hydrolysis reaction, which produced low friction fault and transformations to creep. The creep process progressively developed several wide shear zones including of R, Y, T, P shear plane that comprise gouge zones embedded into wide damage zones, which caused small earthquake distributed along wide fault zones with focal mechanism covered by normal fault, strike-slip fault and reverse fault. However, the stick-slip produced mirror-like slide surfaces with very narrow gouges along R shear plane and Y shear plane, which caused small earthquake distributed along narrow fault zones with single kind of focal mechanism. 相似文献
6.
Internal structures and high-velocity frictional properties of Longmenshan fault zone at Shenxigou activated during the 2008 Wenchuan earthquake 下载免费PDF全文
下载免费PDF全文 Yu Wang Shengli Ma Toshihiko Shimamoto Lu Yao Jianye Chen Xiaosong Yang Honglin He Jiaxiang Dang Linfeng Hou Tetsuhiro Togo 《地震科学（英文版）》2014,27(5):499-528
This paper reports internal structures of a wide fault zone at Shenxigou, Dujiangyan, Sichuan province, China, and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2008 Wenchuan earthquake. Vertical offset and horizontal displacement at the trench site were 2.8 m (NW side up) and 4.8 m (right-lateral), respectively. The fault zone formed in Triassic sandstone, siltstone, and shale about 500 m away from the Yingxiu-Beichuan fault, a major fault in the Longmenshan fault system. A trench survey across the coseismic fault, and observations of outcrops and drill cores down to a depth of 57 m revealed that the fault zone consists of fault gouge and fault breccia of about 0.5 and 250–300 m in widths, respectively, and that the fault strikes N62°E and dips 68° to NW. Quaternary conglomerates were recovered beneath the fault in the drilling, so that the fault moved at least 55 m along the coseismic slip zone, experiencing about 18 events of similar sizes. The fault core is composed of grayish gouge (GG) and blackish gouge (BG) with very complex slip-zone structures. BG contains low-crystalline graphite of about 30 %. High-velocity friction experiments were conducted at normal stresses of 0.6–2.1 MPa and slip rates of 0.1–2.1 m/s. Both GG and BG exhibit dramatic slip weakening at constant high slip rates that can be described as an exponential decay from peak friction coefficient μ p to steady-state friction coefficient μ ss over a slip-weakening distance D c. Deformation of GG and BG is characterized by overlapped slip-zone structures and development of sharp slickenside surfaces, respectively. Comparison of our data with those reported for other outcrops indicates that the high-velocity frictional properties of the Longmenshan fault zones are quite uniform and the high-velocity weakening must have promoted dynamic rupture propagation during the Wenchuan earthquake. 相似文献
7.
在气体介质三轴高温岩石力学实验仪器上,采用意大利Scaglia Bianca石灰岩,在温度50～300℃、围压150MPa,含50MPa孔隙压、无孔隙压含饱和水和完全干燥三种条件下,开展摩擦滑动实验.实验力学数据和显微结构表明,完全干燥样品在120℃时出现慢滑移,实验样品中没有出现溶解与沉淀.无孔隙压含饱和水条件下,100℃、120℃、150℃条件下出现典型的慢滑移,实验样品中含有微弱的溶解与沉淀;300℃条件下出现黏滑,实验样品中出现沉淀.在含50MPa孔隙压条件下,50℃时的实验表现为典型的稳滑,实验样品中以溶解为主;在100～150℃时,出现慢滑移,实验样品中以溶解为主,沉淀为辅;在200～300℃时,出现典型黏滑,实验样品中以沉淀为主.实验结果表明,石灰岩断层泥摩擦滑动稳定性随温度变化,受流体中碳酸钙的溶解和沉淀作用控制,因此,流体中矿物质的饱和度这一化学性质对断层带的摩擦强度和摩擦滑动稳定性具有显著影响. 相似文献
8.
基于速率与状态依赖性摩擦本构关系理论框架,在热水条件下研究了角闪石断层泥的摩擦滑动性质并与闪长岩的另一种主要矿物斜长石的摩擦滑动性质进行了对比.摩擦实验是在三轴实验系统上完成,有效正应力200 MPa,孔隙压力30 MPa,并将加载速率在1.22 μm/s和 0.122 μm/s之间实施了切换.结果表明角闪石的摩擦系数均值为0.70±0.01,随着温度增加没有系统性的变化,整体低于斜长石的摩擦系数(0.75±0.01);计算与实验表明,角闪石和斜长石的摩擦系数的体积分数加权平均值与闪长岩的摩擦系数基本一致;角闪石在实验温度范围内(100～614 ℃)显示速率强化(a-b>0),与斜长石在整个温度范围内的速率弱化(a-b<0)正好相反;角闪石的速率依赖性在整个实验温度范围内无系统性的变化. 相似文献
9.
The frictional behavior of lizardite and antigorite serpentinites: Experiments,constitutive models,and implications for natural faults 总被引：2，自引：0，他引：2
Laboratory studies of the frictional behavior of rocks can provide important information about the strength and sliding stability of natural faults. We have conducted friction experiments on antigorite and lizardite serpentinites, rocks common to both continental and oceanic crustal faults. We conducted both velocity-step tests and timed-hold tests on bare surfaces and gouge layers of serpentinite at room temperature. We find that the coefficient of friction of lizardite serpentinite is quite low (0.15–0.35) and could explain the apparent low stresses observed on crustal transform faults, while that of antigorite serpentinite is comparable to other crustal rocks (0.50–0.85). The frictional behavior of both types of serpentinite is well described by a two-mechanism model combining state-variable-dominated behavior at high slip velocities and flow-dominated behavior at low velocities. The two-mechanism model is supported by data from velocity-step tests and timed-hold tests. The low velocity behavior of serpentinite is strongly rate strengthening and should result in stable fault creep on natural faults containing either antigorite or lizardite serpentinite. 相似文献
10.
AN EXPERIMENTAL STUDY ON THE PROCESS OF INTERGRANULAR PRESSURE SOLUTION OF PLAGIOCLASE GOUGE UNDER HIGH TEMPERATURE AND PRESSURE: METHOD AND PRELIMINARY RESULTS 下载免费PDF全文
下载免费PDF全文 To understand the mechanism of lower-crust earthquake and slow slips, it is necessary to study the frictional properties of mafic rocks and their major rock-forming minerals. Previous studies have performed a series of experimental researches on gabbro, basalt and their major constituents.
According to the results of previous experiments, frictional sliding of plagioclase under hydrothermal conditions(100~600℃)shows a property of velocity weakening, and the experimental results show that both the direct rate effect parameter(a)and the healing effect parameter(b)increase with temperature, a typical feature for thermally-activated processes. Velocity weakening means property of a shear band that has a stronger friction healing effect than the direct rate effect in the rate and state friction constitutive framework, and the healing effect(b value)in constitutive relation mainly reflects the increase in contact area with time under hydrothermal conditions, with some minor effect of structural changes. Since the microphysical mechanism of feldspar minerals at the contacts is mainly brittle cataclasis for temperatures below 600℃, the significant frictional healing effect in this case can only be explained by the mechanism of pressure solution. In order to determine if the dissolution process of plagioclase actually occurs on the laboratory time scale, we conducted hydrostatic experiments on plagioclase powder samples under hydrothermal conditions whereby frequent contact switch between particles seen in frictional sliding experiments can be avoided, making the observation on the dissolution sites possible.
Experimental temperatures were 400℃ and 500℃, with confining pressure of 90~150MPa, pore pressure of 30MPa, with 2mm initial thickness of fault gouge. The mechanical data show that a creep process occurred in the plagioclase fault gouge in the experimental temperature and pressure range; and the microstructures of the experiment show that precipitation of new grains is prevalent as the product of pressure solution process between plagioclase particles. At the same time, it is observed that the contact points have an appearance similar to fused, fuzzy structure as signatures of dissolution. The results of our experiments provide a definite experimental evidence for the healing mechanism in friction of plagioclase and for the theoretical relation between unstable slip and the pressure solution process.
The results of the experiments are summarized as follows:
(1)Drainage rate of pore water in plagioclase gouge was high in the first few hours of experiment, but gradually decreases over time for both temperature and pressure series of experiments slowing down to a steady state. This feature indicates that there is a creep process that evolves inside the plagioclase gouge.
In the temperature-series experiments, the drainage rate of the pore water in the plagioclase gouge at 400℃ is relatively low than the cases for higher temperatures. Thus, the applied temperature is positively correlated with the creep of plagioclase gouge.
(2)Scanning electron microscopy(SEM)observations of the experimentally deformed samples were performed on thin sections cut along the sample axis. Firstly, from the images of microstructure, it was found that the degree of particle fracture became more significant at a higher effective pressure, with smaller pore volume between particles. In the temperature-series experiments it was found that the degree of compaction of plagioclase gouge increased with increasing temperature. Precipitation of plagioclase grains in layered structures was generally observed in high-magnification images, indicating the presence of pressure solution processes. Contact points were also found to be in a state of ambiguity that seems to be a fused morphology, but the details of the structure remain to be determined by further observations.
The above results indicate that the pressure solution process of plagioclase particles can occur on a typical laboratory time scale, and the results of this study provide robust experimental evidences for the theory that links between pressure solution and the mechanism of frictional healing and unstable slips for plagioclase. 相似文献
11.
12.
Abstract The 1999 Chi-Chi earthquake in Taiwan ( M w = 7.6) produced a surface rupture along the north–south-striking Chelungpu thrust fault with pure dip-slip (east side up) and left lateral strike-slip displacements. Near-field strong-motion data for the northern part of the fault illustrate a distinct lack of the high-frequency seismic radiation associated with a large slip (10–15 m) and a rapid slip velocity (2–4 m/s), suggesting a smooth seismic slip associated with low dynamic frictional resistance on the fault. A drillhole was constructed at shallow depths in the possible fault zones of the northern part of the Chelungpu Fault, which may have slipped during the 1999 earthquake. One of the zones consists of a 20-cm-thick, unconsolidated fault breccia with a chaotic texture lacking both discrete slip surfaces (e.g. Riedel shears) and grain crushing. Other possible fault zones are marked by the narrow (less than a few centimeters) gouge zone in which clayey material intrudes into the damaged zone outside of the gouge zone. These characteristic fault rock textures suggest that the slip mechanisms at shallow levels during the earthquake involved either granular flow of initially unconsolidated material or slip localization under elevated pore pressure along the narrow clayey gouge zone. Because both mechanisms lead to low dynamic frictional resistance on the fault, the rapid seismic slip in the deep portions of the fault (i.e. the source region of strong-motion radiation) could have been accommodated by frictionless slip on the shallow portions of the fault. The combination of strong-motion data and fault rock analysis suggests that smooth slip associated with low dynamic friction occurred on both the deep and shallow portions of the fault, resulting in a large slip between the source region and the surface in the northern region. 相似文献
13.
蒙脱石的脱水作用对断层摩擦本构行为的影响 总被引：4，自引：3，他引：4
利用高温双轴摩擦装置，研究了含蒙脱石的断层带在不同温度下摩擦滑动的速度依赖性，以期了解脱水作用对摩擦行为的影响。结果表明，断层带摩擦强度随温度而升高，而速度依赖性较为复杂，以１．４ｕ／ｓ为界，室温和１００℃时，低滑动速率下表现为微弱的速度弱化，高滑动速率下则表现为速度强化；２００℃时均为速度强化；３００℃时高滑动速率下仍为速度强化，但低滑动速率下转变为速度弱化；４００℃以上，均为明显的速度弱化。摩擦行为的变化与脱水过程及相应的断层物质变形方式的变化密切相关 相似文献
14.
15.
16.
黑云母是自然界常见的层状硅酸盐矿物,其摩擦系数不高且化学稳定性好,对其摩擦性质的关注可能会对弱断层的研究有所帮助.本次工作选取的实验温度条件对应于典型地壳强度模型中脆塑性转化带的范围,为300 ℃和400 ℃.有效正应力为200 MPa,孔隙水压包括10 MPa和30 MPa,在此条件下对黑云母模拟断层泥进行摩擦实验研究.实验得出黑云母的摩擦系数平均在0.36左右.速度依赖性随温度升高速度弱化的程度增强,表现为300 ℃为十分微弱的速度弱化,而在400 ℃出现了黏滑行为,代表了更强的速度弱化.显微结构中同时出现了脆性剪切变形和塑性扭折变形,但决定宏观力学性质的显然是脆性剪切变形.在黑云母存在的情况下,本研究的实验结果有助于理解大陆地壳脆塑性转化带中地震的可能性和弱断层深部的变形机制、宏观力学行为以及地震活动. 相似文献
17.
Internal structure of Longmenshan fault zone at Hongkou outcrop,Sichuan, China,that caused the 2008 Wenchuan earthquake 下载免费PDF全文
下载免费PDF全文 This paper reports the internal structures of the Beichuan fault zone of Longmenshan fault system that caused the 2008 Wenchuan earthquake, at an outcrop in Hongkou, Sichuan province, China. Present work is a part of comprehensive project of Institute of Geology, China Earthquake Administration, trying to understand deformation processes in Longmenshan fault zones and eventually to reproduce Wenchuan earthquake by modeling based on measured mechanical and transport properties. Outcrop studies could be integrated with those performed on samples recovered from fault zone drilling, during the Wenchuan Earthquake Fault Scientific Drilling (WFSD) Project, to understand along-fault and depth variation of fault zone properties. The hanging wall side of the fault zone consists of weakly-foliated, clayey fault gouge of about 1 m in width and of several fault breccia zones of 30–40 m in total width. We could not find any pseudotachylite at this outcrop. Displacement during the Wenchuan earthquake is highly localized within the fault gouge layer along narrower slipping-zones of about 10 to 20 mm in width. This is an important constraint for analyzing thermal pressurization, an important dynamic weakening mechanism of faults. Overlapping patterns of striations on slickenside surface suggest that seismic slip at a given time occurred in even narrower zone of a few to several millimeters, so that localization of deformation must have occurred within a slipping zone during coseismic fault motion. Fault breccia zones are bounded by thin black gouge layers containing amorphous carbon. Fault gouge contains illite and chlorite minerals, but not smectite. Clayey fault gouge next to coseismic slipping zone also contains amorphous carbon and small amounts of graphite. The structural observations and mineralogical data obtained from outcrop exposures of the fault zone of the Wenchuan earthquake can be compared with those obtained from the WFSD-1 and WFSD-2 boreholes, which have been drilled very close to the Hongkou outcrop. The presence of carbon and graphite, observed next to the slipping-zone, may affect the mechanical properties of the fault and also provide useful information about coseismic chemical changes. 相似文献
18.
野外地质调查结果显示,断层带常富集碳质.断层带中碳的分布结构是影响断层带电导率特征的一种重要参数.本文在室温、室内湿度和2MPa正应力条件下,对不同石墨含量(3,5,6和7wt%)的石英-石墨混合断层泥模拟样品开展了滑动速率介于500μm·s-1～1m·s-1的摩擦实验及相应的电导率测量,以期研究断层运动对碳分布结构的影响以及断层带电性特征对碳含量及分布的响应情况.结果显示,摩擦滑动能够显著地改变样品的电性特征(电导率大小及其各向异性).在平行滑动面方向(径向),样品电导率随着滑动位移的增加快速增加,在滑动约数十厘米之后,其电导率基本达到稳定状态;在垂直滑动面方向(轴向),样品电导率基本不随摩擦滑动速率和滑动距离而变化.SEM显微结构观测显示,摩擦滑动所引起的电导率各向异性直接反映了石墨分布结构的变化.该研究结果深化了对地震断裂带浅部电性特征的认识,为野外断层带大地电磁测深资料的解释提供了约束,同时对于了解含碳断层的力学性质和弱矿物相在剪切变形中的分布特征及其演化过程等方面也具有重要意义. 相似文献
19.
断层泥的再生显微结构特征及其地震地质意义 总被引：3，自引：1，他引：3
三轴剪切摩擦实验后的断层泥与天然断层泥的再生显微结构特征研究表明，断层泥的显微结构特征与断层滑动方式之间有一定的关系，稳滑使断层泥变形均匀，产生低角度剪切（＜１４°）、布丁构造和颗粒碎裂流动。粘滑使断层泥局部发生强烈变形、高角度剪切（＞１４°）和碎粒出现随机裂纹等。断层泥的再生显微结构特征可用作鉴别古地震的存在 相似文献