共查询到20条相似文献，搜索用时 15 毫秒
1.
A series of flume experiments were done to investigate the effect of grain composition on the critical gradient and discharge of debris flows initiated in seasonal gullies. The results indicated that the critical gradient and discharge for debris flow initiation decrease initially, and then increase as the mass content of fine particles (<2 mm) increases. As the mass content of fine particles increases, the angle of repose, permeability of widely graded gravel soils, and the incipient motion conditions of the coarse grains in non-uniform sediments decrease at first, and then increase. The mass content of fine particles of all inflection points is the same. The theoretical model based on the combination of hydrodynamic force and shear stress is more applicable to the prediction of the critical gradient for debris flow initiation. The critical discharge model considering the effect of non-homogeneity of the soil and the size of coarse and fine grains provides a more accurate prediction of debris flow initiation than other models based on the mean diameter. 相似文献
2.
Hyunwook Choo Qian Zhao Susan E. Burns Terry W. Sturm Seung Ho Hong 《地球表面变化过程与地形》2020,45(7):1499-1509
Sedimentation – including erosion, transport, and deposition of coarse-grained particles – is a primary and growing environmental, engineering, and agricultural issue around the world. Soil erosion occurs when the hydrodynamic force induced by flowing water exceeds the geotechnical resistance of soils, as measured by critical shear stress for initiation of soil-particle motion. Even though various quantitative methods have been suggested with respect to different types of soil, the most widely accepted formula to estimate critical shear stress for coarse-grained soil is a direct function of the median grain size of the soil particles; however, the erosion resistance of soils also varies with other geotechnical properties, such as packing density, particle shape, and uniformity coefficient. Thus, in this study, a combined rolling–lift model for particle detachment was derived based on theoretical analysis. A series of experimental flume tests were conducted with specimens prepared with standard soil types, as well as laboratory-prepared mixtures of coarse-grained soil to validate the theoretical model and determine the effect of other geotechnical properties on the erosion characteristics of coarse grains, coupled with the effect of median particle size. The results indicated that the median grain size is the primary variable determining the resistance of coarse grains, but the critical shear stress also varies with the packing density of the soil matrix. In addition, angular particles show more erosion resistance than rounded particles, and the erosion potential of a soil decreased when the grain is well graded (higher value of uniformity coefficient). Additionally, regression analysis was performed to quantify the effect of each parameter on the critical shear stress of coarse grains. © 2020 John Wiley & Sons, Ltd. 相似文献
3.
A two‐dimensional simulation model of travel distances of individual particles in a gravel‐bed river is presented. The model is based on a number of rules, which include particle size, entrainment, trajectory, distance of movement and entrapment. Particle interactions are controlled by resistance fields defined about each obstacle and critical elevation defined in the model. Resistance fields, particle dropping and critical elevation rules control particle interactions. The interaction rules cause the particles to develop pebble clusters, stone cells and transverse structures (transverse ribs). The simulated travel distances of individual particles are consistent with reported field results. Individual particle travel distances were simulated using two different models; one without interactions between the individual particles and the stationary bed and one with interactions. The case without interactions demonstrates the random nature of sediment transport, and narrow ranges of travel distances. Wider ranges of travel distances, similar to those for natural situations, were obtained for the cases with interactions. The more intense the interaction between the mobile stones and the stationary ones, the wider the range of distances of travel for a given particle size. Modelling the mean travel distance yielded a result similar to that published previously, which was based on empirical data. Well developed bed‐surface structures were obtained for relatively poorly sorted sediment with intense interactions between particles. Transverse structures developed when relatively large particles were allowed to move. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
4.
Bed scour by debris flows: experimental investigation of effects of debris‐flow composition 
下载免费PDF全文
下载免费PDF全文 Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
5.
Sediment grains in a bedrock‐alluvial river will be deposited within or adjacent to a sediment patch, or as isolated grains on the bedrock surface. Previous analysis of grain geometry has demonstrated that these arrangements produce significant differences in grain entrainment shear stress. However, this analysis neglected potential interactions between the sediment patches, local hydraulics and grain entrainment. We present a series of flume experiments that measure the influence of sediment patches on grain entrainment. The flume had a planar bed with roughness that was much smaller than the diameters of the mobile grains. In each experiment sediment was added either as individual grains or as a single sediment pulse. Flow was then increased until the sediment was entrained. Analysis of the experiments demonstrates that: (1) for individual grains, coarse grains are entrained at a higher discharge than fine grains; (2) once sediment patches are present, the different in entrainment discharge between coarse and fine grains is greatly reduced; (3) the sheltering effect of patches also increases the entrainment discharge of isolated grains; (4) entire sediment patches break‐up and are eroded quickly, rather than through progressive grain‐by‐grain erosion; (5) as discharge increases there is some tendency for patches to become more elongate and flow‐aligned, and more randomly distributed across the bed. One implication of this research is that the critical shear stress in bedrock‐alluvial channels will be a function of the extent of the sediment cover. Another is that the influence of sediment patches equalizes critical shear stresses between different grain sizes and grain locations, meaning that these factors may not need to be accounted for. Further research is needed to quantify interactions between sediment patches, grain entrainment and local hydraulics on rougher bedrock surfaces, and under different types of sediment supply. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
6.
Peter R. Wilcock 《地球表面变化过程与地形》1992,17(3):289-298
The largest grains found in samples of transported sediment are commonly used to estimate flow competence. With samples from a range of flows, a relationship between the flow and the largest mobile grain can be derived and used to estimate the critical shear stress for incipient motion of the different grain sizes in the bed sediment or, inversely, to estimate the magnitude of the flow from the largest grain found in a transport sample. Because these estimates are based on an extreme value of the transport grain-size distribution, however, they are subject to large errors and are sensitive to the effect of sample size, which tends to vary widely in sediment transport samples from natural flows. Furthermore, estimates of the critical shear stress based on the largest sampled moving grain cannot be scaled in a manner that permits reasonable comparison between fractions. The degree to which sample size and scaling problems make largest-grain estimates of fractional critical shear stress deviate from a true relationship cannot be predicted exactly, although the direction of such a deviation can be demonstrated. The large errors and unknown bias suggest that the largest sampled mobile grain is not a reliable predictor of either critical shear stress or flow magnitude. It is possible to define a single flow competence for the entire mixture, based on a central value of the transport grain-size distribution. Such a measure is relatively stable, does not require between-fraction scaling, and appears to be well supported by observation. 相似文献
7.
In order to contribute to a reliable, easy-to-handle and economically viable erosion risk assessment of contaminated riverine sites, the present study aims to implement master-variables best characterising the sediment stability. Thus, a wide range of sediment properties was related to the critical shear stress for mass erosion, determined in the SETEG (Stroemungskanal zur Ermittlung der tiefenabhaengigen Erosionsstabilitaet von Gewaessersedimenten) pressurised channel, with special emphasis on vertical and temporal gradients in the Lauffen reservoir on the River Neckar. Over the course of 1 year, positive impacts of some macrofauna species and benthic diatoms on the sediment stability were detected for the sediment surface (0.5 cm). However, a high seasonal variability of biological parameters caused varying relations with erosion resistance in the upper sediment layers as shown for the colloidal carbohydrates. Considering only deeper sediment layers (5–35 cm), a more general pattern could be revealed with correlations between the critical shear stress and single sediment properties such as depth, grain size, total organic carbon (TOC), cation exchange coefficient (CEC), carbohydrates and proteins. Firstly, the influence of physico-chemical and biological properties on erosion resistance became evident, even over depths at 0–35 cm. Secondly, inter-particle forces are most important for erosion resistance. These are enhanced in fine-grained sediment layers, offering high binding capacities but also strengthened by polymeric substances permeating the void space and coating particles. These covariance patterns of sedimentological and biological parameters are addressed by multivariate statistical tests (principal component analysis), resulting in a higher magnitude of the correlation coefficient between critical shear stress and the master-variables in main component II (polymeric substances, grain size, TOC, CEC; R=0.77) compared to single correlations. 相似文献
8.
Sediment transport and channel morphology in mountainous hillslope-coupled streams reflect a mixture of hillslope and channel processes. However, the influence of lithology on channel form and adjustment and sediment transport remains poorly understood. Patterns of channel form, grain size, and transport capacity were investigated in two gravel-bed streams with contrasting lithology (basalt and sandstone) in the Oregon Coast Range, USA, in a region in which widespread landslides and debris flows occurred in 1996. This information was used to evaluate threshold channel conditions and channel bed adjustment since 1996. Channel geometry, slope, and valley width were measured or extracted from LiDAR and sediment textures were measured in the surface and subsurface. Similar coarsening patterns in the first few kilometres of both streams indicated strong hillslope influences, but subsequent downstream fining was lithology-dependent. Despite these differences, surface grain size was strongly related to shear stress, such that the ratio of available to critical shear stress for motion of the median surface grain size at bankfull stage was around one over most of the surveyed lengths. This indicated hydraulic sorting of supplied sediment, independent of lithology. We infer a cycle of adjustment to sediment delivered during the 1996 flooding, from threshold conditions, to non-alluvial characteristics, to threshold conditions in both basins. The sandstone basin can also experience complete depletion of the gravel-size alluvium to sand size, leading to bedrock exposure because of high diminution rates. Although debris flows being more frequent in a basalt basin, this system will likely display threshold-like characteristics over a longer period, indicating that the lithologic control on channel adjustment is driven by differences in rock competence that control grain size and available gravel for bed load transport. © 2020 John Wiley & Sons, Ltd. 相似文献
9.
The microstructural state and evolution of fault gouge has important implications for the mechanical behaviour, and hence
the seismic slip potential of faults. We use 3D discrete element (DEM) simulations to investigate the fragmentation processes
operating in fault gouge during shear. Our granular fault gouge models consist of aggregate grains, each composed of several
thousand spherical particles stuck together with breakable elastic bonds. The aggregate grains are confined between two blocks
of solid material and sheared under a given normal stress. During shear, the grains can fragment in a somewhat realistic way
leading to an evolution of grain size, grain shape and overall texture. The ‘breaking up’ of the fault gouge is driven by
two distinct comminution mechanisms: grain abrasion and grain splitting. The relative importance of the two mechanisms depends
on applied normal stress, boundary wall roughness and accumulated shear strain. If normal stress is sufficiently high, grain
splitting contributes significantly to comminution, particularly in the initial stages of the simulations. In contrast, grain
abrasion is the dominant mechanism operating in simulations carried out at lower normal stress and is also the main fragmentation
mechanism during the later stages of all simulations. Rough boundaries promote relatively more grain splitting whereas smooth
boundaries favor grain abrasion. Grain splitting (plus accompanying abrasion) appears to be an efficient mechanism for reducing
the mean grain size of the gouge debris and leads rapidly to a power law size distribution with an exponent that increases
with strain. Grain abrasion (acting alone) is an effective way to generate excess fine grains and leads to a bimodal distribution
of grain sizes. We suggest that these two distinct mechanisms would operate at different stages of a fault’s history. The
resulting distributions in grain size and grain shape may significantly affect frictional strength and stability. Our results
therefore have implications for the earthquake potential of seismically active faults with accumulations of gouge. They may
also be relevant to the susceptibility of rockslides since non-cohesive basal shear zones will evolve in a similar way and
potentially control the dynamics of the slide. 相似文献
10.
筑坝拦截对黑河河道沉积物粒度空间分布的影响 总被引：2，自引：1，他引：1
河流沉积物对流域环境变化具有敏感响应,其粒度参数能反映沉积环境中物质来源和水动力环境.本文以黑河流域上中游为研究区域,探究河流沉积物粒度对流域环境变化的响应.从黑河上中游干流22个主要控制断面采集河床沉积物样品,采用筛分法和吸管法对沉积物样品粒度参数进行测定,并分析其空间分布规律对筑坝拦截为主的环境改变响应.研究结果表明：受梯级水库建设影响,黑河上中游泥沙粒径大小差异显著.干流库区泥沙粒径较自然河段明显减小,分选很好,呈正偏或极正偏尖锐分布,而且在库区不同沉积高度上表现出分层沉积特征;坝下游河段因遭受强烈冲刷,较自然河段泥沙粒径粗化显著,分选变差,偏态趋向极正偏,峰态尖锐化;水库回水区受水库壅水及下泄清水的双重制约,泥沙粒度参数介于自然河段和坝下游河段之间,整体分选中等,呈极正偏尖锐分布;沉积环境分析表明,上游支流河段沉积物粒度特征受泥沙供给和物源特征的影响较水动力条件显著,干流河段沉积物粒度特征主要受水动力条件控制.研究结果既符合河流上中游沉积物粒度分布规律,也反映了河流环境变化对沉积物粒度组成的影响. 相似文献
11.
Most gravel‐bed streams exhibit a surface armour in which the median grain size of the surface particles is coarser than that of the subsurface particles. This armour has been interpreted to result when the supply of sediment is less than the ability of the stream to move sediment. While there may be certain sizes in the bed for which the supply is less than the ability of the stream to transport these sizes, for other sizes of particles the supply may match or even exceed the ability of the channel to transport these particles. These sizes of particles are called ‘supply‐limited’ and ‘hydraulically limited’ in their transport, respectively, and can be differentiated in dimensionless sediment transport rating curves by size fractions. The supply‐ and hydraulically limited sizes can be distinguished also by comparing the size of particles of the surface and subsurface. Those sizes that are supply‐limited are winnowed from the bed and are under‐represented in the surface layer. Progressive truncation of the surface and subsurface size distributions from the ?ne end and recalculation until the size distributions are similar (collapse), establishes the break between supply‐ and hydraulically limited sizes. At sites along 12 streams in Idaho ranging in drainage area from about 100 to 4900 km2, sediment transport rating curves by size class and surface and subsurface size distributions were examined. The break between sizes that were supply‐ and hydraulically limited as determined by examination of the transport rate and surface and subsurface size distributions was similar. The collapse size as described by its percentile in the cumulative size distribution averaged D36 of the surface and D73 of the subsurface. The discharge at which the collapse size began to move averaged 88 per cent of bankfull discharge. The collapse size decreased as bed load yield increased and increased with the degree of selective transport. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
12.
Vito Bacchi Alain Recking Nicolas Eckert Philippe Frey Guillaume Piton Mohamed Naaim 《地球表面变化过程与地形》2014,39(8):1075-1086
In poorly mobile static armour, sorting is usually considered the result of hiding/exposure effects. We called this effect ‘static sorting’ in opposition to very efficient grain‐to‐grain mechanisms produced by a mobile mixture, called ‘kinetic sorting’. We hypothesized that kinetic sorting can be an important contributor to the morphodynamics of mountain streams and attempted to demonstrate this with new flume experiments. Two long runs were produced with natural poorly sorted sediments, and with transport stages of the coarse fraction (defined by the ratio between the shear stress and the critical shear stress for transport), smaller and higher than 1, respectively. Both runs produced an efficient transfer downstream of the injected material, but with a major difference: the first run (no kinetic sorting) produced permanent armour figuring clusters, akin to what has already been observed in similar experiments; the second run (with kinetic sorting) also produced bed armouring, but this armour was periodically totally destroyed, leading to substantial bed erosion. This phenomenon was explained by kinetic sorting, the effects of which are to produce an efficient downward migration of fine materials and bed surface armouring. The consequence is that fine materials are hidden to the flow during aggradation, allowing the slope to attain values much steeper than would have been expected at equilibrium for the mixture. However, whereas the surface armouring tends to stabilize the bed, construction of a layer of fine sediments at the subsurface also contributes to making it very unstable. These two contradictory effects explain the complex bed behaviours and the existence of very large bedload and slope fluctuations. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
13.
Jasna Muskatirovic 《地球表面变化过程与地形》2008,33(11):1757-1768
Field data are essential in evaluating the adequacy of predictive equations for sediment transport. Each dataset based on the sediment transport rates and other relevant information gives an increased understanding and improved quantification of different factors influencing the sediment transport regime in the specific environment. Data collected for 33 sites on 31 mountain streams and rivers in Central Idaho have enabled the analysis of sediment transport characteristics in streams and rivers with different geological, topographic, morphological, hydrological, hydraulic, and sedimentological characteristics. All of these streams and rivers have armored, poorly sorted bed material with the median particle size of surface layer coarser than the subsurface layer. The fact that the largest particles in the bedload samples did not exceed the median particle size of the bed surface material indicates that the armor layer is stable for the observed flow discharges (generally bankfull or less, and in some cases two times higher than bankfull discharge). The bedload transport is size‐selective. The transport rates are generally low, since sediment supply is less than the ability of flow to move the sediment for one range of flow discharges, or, the hydraulic ability of the stream is insufficient for entrainment of the coarse bed material. Detailed analyses of bedload transport rates, bedload and bed material characteristics were performed for each site. The obtained results and conclusions are used to identify different influences on bedload transport rates in analyzed gravel‐bed rivers. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
14.
Modelling soil erosion requires an equation for predicting the sediment transport capacity by interrill overland flow on rough surfaces. The conventional practice of partitioning total shear stress into grain and form shear stress and predicting transport capacity using grain shear stress lacks rigour and is prone to underestimation. This study therefore explores the possibility that inasmuch as surface roughness affects flow hydraulic variables which, in turn, determine transport capacity, there may be one or more hydraulic variables which capture the effect of surface roughness on transport capacity suffciently well for good predictions of transport capacity to be achieved from data on these variables alone. To investigate this possibility, regression analyses were performed on data from 1506 flume experiments in which discharge, slope, water temperature, rainfall intensity, and roughness size, shape and concentration were varied. The analyses reveal that 89·8 per cent of the variance in transport capacity can be accounted for by excess flow power and flow depth. Including roughness size and concentration in the regression improves that explained variance by only 3·5 per cent. Evidently, flow depth, when used in combination with excess flow power, largely captures the effect of surface roughness on transport capacity. This finding promises to simplify greatly the task of developing a general sediment equation for interrill overland flow on rough surfaces. Copyright © 1998 John Wiley & Sons, Ltd. 相似文献
15.
《国际泥沙研究》2020,35(2):203-216
Accurate evaluation and prediction of bedload transport are crucial in studies of fluvial hydrodynamic characteristics and river morphology.This paper presents a one-dimensional numerical model based on the one-dimensional lateral distribution method(1 D-LDM) and six classic bedload transport formulae that can be used to simulate hydrodynamic characteristics and bedload transport discharge in cross sections.Two gravel-bed rivers,i.e.the Danube River located approximately 70 km downstream from Bratislava in Slovakia and the Tolten River in south of Chile are used as examples.In the 1 D-LDM,gravity,bed shear stress,turbulent diffusion,and secondary flow are included to allow for accurate predictions of flow velocity and consequently bed shear stress in the cross sections.Six classic formulae were applied to evaluate the non-dimensional bedload transport rate,and the bedload transport discharge through a river cross section is obtained by integrating the bedload transport rate over the width of the cross section.The results show that the root mean square error(RMSE) and mean absolute error(MAE) of velocity and water discharge were less than 8% of the observed magnitude,while the correlation coefficient between model predictions and observations was close to unity.The formulae proposed by Ashida and Michiue(1972),in which particle collision with the bed is taken into account,and by Camenen and Larson(2005),which allows for yielding a non-zero bedload transport rate even when the bed shear stress is smaller than the critical bed shear stress value,appeared to be more appropriate for predicting the observed bedload transport rate in the studied cross sections of two gravel-bed rivers.If non-uniform sediment mixtures were considered,the bedload transport discharge through a cross-section could change considerably by up to 22.5% of the observed magnitude.The relations proposed by Ashida and Michiue(1972) and Egiazaroff(1965) for parameterizing the hiding factor yielded more realistic model predictions in comparison with observations for the measured data set collected for the Tolten River,while the one proposed by Wilcock and Crowe(2003) performs the best for the data set measured for the Danube River. 相似文献
16.
The paper presents the results of field measurements of critical conditions for bedload motion conducted in the Rio Cordon, a steep boulder‐bed stream in the Italian Alps, under conditions of high Reynolds numbers and low relative submergence poorly explored before. Two methods have been used to determine threshold of motion: the displacement of marked clasts and the flow competence approach, which uses the largest grain size diameter transported by each flood event. The high values of confirm the great relevance of non‐bedload effective shear stresses in step–pool streams given by the additional form drag associated with this morphology. Relative submergence effects on the dimensionless critical shear stress have been quantified by considering the relative submergence ratio Rh/D84, and the major effect of relative size on the mobility of each particle in steep, widely graded bed mixtures has been evaluated. Finally, the dimensionless critical unit discharge has also been adopted in the regression equations as the critical hydraulic parameter, because it may represent an easier parameter to use than the critical shear stress for steep, rough mountain rivers. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
17.
John Pitlick Erich R. Mueller Catalina Segura Robert Cress Margaret Torizzo 《地球表面变化过程与地形》2008,33(8):1192-1209
This study investigates trends in bed surface and substrate grain sizes in relation to reach‐scale hydraulics using data from more than 100 gravel‐bed stream reaches in Colorado and Utah. Collocated measurements of surface and substrate sediment, bankfull channel geometry and channel slope are used to examine relations between reach‐average shear stress and bed sediment grain size. Slopes at the study sites range from 0·0003 to 0·07; bankfull depths range from 0·2 to 5 m and bankfull widths range from 2 to 200 m. The data show that there is much less variation in the median grain size of the substrate, D50s, than there is in the median grain size of the surface, D50; the ratio of D50 to D50s thus decreases from about four in headwater reaches with high shear stress to less than two in downstream reaches with low shear stress. Similar trends are observed in an independent data set obtained from measurements in gravel‐bed streams in Idaho. A conceptual quantitative model is developed on the basis of these observations to track differences in bed load transport through an idealized stream system. The results of the transport model suggest that downstream trends in total bed load flux may vary appreciably, depending on the assumed relation between surface and substrate grain sizes. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
18.
Tsunami Sediment Characteristics at the Thai Andaman Coast 总被引：1，自引：0，他引：1
This paper describes and summarizes the 2004 Indian Ocean tsunami sediment characteristics at the Thai Andaman coast. Field investigations have been made approximately 3 years after the 2004 Indian Ocean tsunami event. Seven transects have been examined at five locations. Sediment samples have been collected for grain-size analyses by wet-sieve method. Tsunami sediments are compared to three deposits from coastal sub-environments. The mean grain-size and standard deviation of deposits show that shoreface deposits are fine to very fine sand, poorly to moderately well sorted; swash zone deposits are coarse to fine sand, poorly to well sorted; berm/dune deposits are medium to fine sand, poorly to well sorted; and tsunami deposits are coarse to very fine sand, poorly to moderately well sorted. A plot of deposit mean grain-size versus sorting indicates that tsunami deposits are composed of shoreface deposits, swash zone deposits and berm/dune deposits as well. The tsunami sediment is a gray sand layer deposited with an erosional base on a pre-existing soil (rooted soil). The thickness of the tsunami sediment layer is variable. The best location for observation of the recent tsunami sediment is at about 50–200 m inland from the coastline. In most cases, the sediment layer is normally graded. In some cases, the sediment contains rip-up clasts of muddy soils and/or organic matter. The vertical variation of tsunami sediment texture shows that the mean grain-size is fining upward and landward. Break points of slope in a plot of standard deviation versus depth mark a break in turbulence associated with a transition to a lower or higher Reynolds number runup. This can be used to evaluate tsunami sediment main layer and tsunami sediment sub layers. The skewness of tsunami sediment indicates a grain size distribution with prominent finer-grain or coarse-grain particles. The kurtosis of tsunami sediment indicates grain-size distributions which are flat to peak distribution (or multi-modal to uni-modal distribution) upward. Generally, the major origins of tsunami sediment are swash zone and berm/dune zone sands where coarse to medium sands are the significant material at these locations. The minor origin of tsunami sediment is the shoreface where the significant materials are fine to very fine sands. However, for a coastal area where the shoreface slope is mild, the major origin of tsunami sediment is the shoreface. The interpretation of runup number from tsunami sediment characteristics gets three runups for the 2004 Indian Ocean tsunami at the Thai Andaman coast. It corresponds to field observations from local eyewitnesses. The 1st runup transported and deposited more coarse particles than the following runups. Overall, the pattern of onshore tsunami sediment transportation indicates erosion at swash zone and berm/dune zone, followed by dynamic equilibrium at an area behind the berm/dune zone and after that deposition at inland zone until the limit of sediment inundation. The total deposition is a major pattern in onshore tsunami sediment transportation at the deposition zone which the sediment must find in the direction of transport. 相似文献
19.
John S. Bridge 《地球表面变化过程与地形》1977,2(4):401-416
Bed topography and grain size are predicted for steady, uniform flow in circular bends by consideration of the balance of fluid, gravity and frictional forces acting on bed load particles. Uniform flow pattern is adequately described by conventional hydraulic equations, with bed shear defined as that effectively acting on bed load grains. This analysis is used as a basis to predict bed topography and grain size for steady, non-uniform flow in non-circular bends (represented by a ‘sine-generated’ curve). The non-uniform flow pattern is calculated using the method of Engelund (1974a). Equilibrium bed form, hence sedimentary structure, is found by comparison of existing flow conditions with one of the schemes describing the hydraulic stability limits of the various bed forms. The model was compared with bankfull flow observations from a channel bend on the River South Esk, Scotland. Theoretical bed topography and velocity distribution were very close to the observed data. However, bed shear stress showed only a broad agreement, probably because of the use a constant friction coefficient value. Mean grain size distribution showed good agreement, but theory did not account adequately for gravel sizes in the talweg region and on the upstream, inner part of the bar, possibly due to theoretical underestimation of effective bed shear. Bed form and sedimentary structure are predicted well using the familiar stream power-grain size scheme. The behaviour of the model under unsteady uniform flow conditions in circular bends was analyzed, and suggests that any variation of grain size and bed topography with stage is likely to be limited to deeper parts of the channel. 相似文献
20.
Hennie Henriët van der Veen Suzanne Jacqueline Marie Hélène Hulscher Michiel Adrianus Frederik Knaapen 《Ocean Dynamics》2006,56(3-4):228-234
Sandy shallow seas, like the North Sea, are very dynamic. Several morphological features are present on the bed, from small ripples to sand waves and large tidal sandbanks. The larger patterns induce significant depth variations that have an impact on human activities taking place in this area. Therefore, it is important to know where these large-scale features occur, what their natural behaviour is and how they interact with human activities. Here, we extend earlier research that compares the results of an idealized model of large-scale seabed patterns with data of seabed patterns in the North Sea. The idealized model is extended with a grain size dependency. The adaptations lead to more accurate predictions of the occurrence of large-scale bed forms in the North Sea. Therefore, grain size dependency and, in particular, critical shear stress are important to explain the occurrence of sand waves and sandbanks in the North Sea.
Responsible Editor: Alejandro Souza 相似文献