共查询到20条相似文献，搜索用时 734 毫秒
1.
发育在帕米尔弧形推覆构造带最前缘的木什活动背斜是一南缓北陡的第四纪滑脱褶皱,背斜的最小地壳缩短量为0.7km,构造隆升幅度可达1.5km.木什背斜北翼逆断层由一系列坡向北的反向断层陡坎组成,不同断坎间垂直位移分布呈现此消彼长的特征,不论是整个北翼逆断层西段还是单条断坎,其垂直位移均呈东高西低的不对称分布,位移梯度东高西... 相似文献
2.
西南天山-塔里木盆地结合带浅深构造关系 ——深地震反射剖面的初步揭露 总被引：4，自引：0，他引：4
盆山结合部的浅-深结构样式是进行陆内造山动力学研究与讨论的重要依据.2007年,在喀什东的天山与塔里木盆地之间的过渡带上,完成了一条近南北向的长度为121 km的主动源深地震反射剖面,显示出盆山结合部现今地壳尺度的构造格架.剖面南部呈现出10~12 km巨厚的沉积盖层,沉积盖层内发育滑脱断层;盆山结合部多排隆起构造以及天山山前上地壳显现出向北倾斜的断裂与地表地质观察吻合;盆山结合带展现出滑脱与逆冲推覆构造相关的断层褶皱;与塔里木盆地稳定沉积层相比,在南天山浅、中层地层受到强烈的变形改造,导致地层比较破碎,反射变弱、连续性较差;时间剖面上可以追踪到比较连续的Moho反射,从南向北有加深的趋势.深地震反射剖面揭露出的西南天山与塔里木盆地的这些浅-深构造,展现出塔里木盆地盖层向南天山滑脱与南天山向塔里木盆地逆冲推覆的特征,反映出陆内汇聚下的盆山耦合关系. 相似文献
3.
位于帕米尔前缘逆冲推覆体(Pamir Front Thrust,PFT)东端的木什滑脱背斜,是帕米尔弧形推覆构造带最前缘和最新的变形带。对地形横剖面、纵剖面和水系发育特征的分析表明,木什背斜总体上具有由西向东扩展生长的特征。在背斜核部及北翼发育数级开阔平坦的沿轴向展布的河流阶地,阶地可划分为4期。利用阶地堆积细颗粒石英光释光测年获得阶地面T2a、T3和T4的形成年龄分别为(15.8±2.40)ka、(55.1±10.3)ka、(131.4±23.9)ka。伴随背斜的生长扩展,河流阶地面发生了横向和纵向掀斜,并形成断层陡坎和褶皱陡坎。木什背斜晚第四纪的缩短和隆升主要是通过褶皱翼旋转机制进行的,估算其最小缩短速率为(1.6±0.3)mm/a,最小隆升速率为(1.9±0.3)mm/a。与此同时,沿轴向背斜发生了向东的侧向迁移和旋转。根据背斜垂直隆升与侧向扩展之间的关系,估算背斜在131～16ka期间向东的侧向迁移扩展速率较快,为 (14.6±3.6)mm/a; 自16ka至今,侧向迁移扩展速率迅速减小至(1.7±0.3)mm/a,背斜向东的迁移扩展可能已基本停止,而以侧向旋转为主。 相似文献
4.
焉耆盆地是塔里木盆地东北缘天山山间的重要坳陷区,盆地北缘发育的和静逆断裂-褶皱带是一条现今活动强烈的逆断裂-褶皱带,对其第四纪以来缩短量和隆升量的计算有利于分析该区域的构造活动情况,对缩短速率和隆升速率的估计可以与天山造山带其他区域的活动速率进行横向对比,从而反映出焉耆盆地在天山晚新生代构造变形的作用。在深部资料不足的情况下,对背斜形态完整、构造样式简单的和静逆断裂-褶皱带,利用地表可获得的地层和断层产状,通过恢复褶皱几何形态,计算褶皱的缩短量、隆升量和断层滑动量,得到逆断裂-褶皱带早更新世晚期(1.8Ma)、中更新世(780ka)和晚更新世中期(80ka)以来的缩短量分别为1.79km、0.88km和26m,初步估计的缩短速率分别为0.99mm/a、1.13mm/a和0.33mm/a。显示和静逆断裂-褶皱带自开始形成以来构造活动强度并不一致。与地壳形变观测结果对比,作为南天山东段最主要的坳陷区,焉耆盆地吸收了这一区域(86°～88°E)的大部分地壳缩短,且主要表现为盆地北缘新生逆断裂-褶皱带的强烈变形。 相似文献
5.
野外考察见到亚肯背斜区发育 3级主要地貌面 ,在第 2级和第 1级地貌面 (冲洪积扇 )之下采集了堆积物的热释光样品 ,测年结果分别为距今 3 96～ 4 36万年和 0 78万年 ,区域地貌对比研究认为 ,第 2级地貌面被废弃的时代为距今 4万年至 1 2～ 1 3万年 ,第 1级地貌面被废弃的时代为距今 0 78万年之后。横跨背斜不同部位地貌面的地形剖面表明 ,第 2级地貌面形成以来褶皱隆起高度达 6 0m ,第 1级地貌面褶皱隆起高度为 2 0m。地震反射剖面显示 ,亚肯背斜区滑脱面深度约7km ,由平衡地质剖面法得到第 2和第 1级地貌面形成以来褶皱的缩短量分别为 4 7m和 17 9m。第 2级地貌面形成以来褶皱的隆起和缩短速率分别为 1 5～ 5mm/a和 1 2～ 3 9mm/a,第 1级地貌面形成以来褶皱隆起和缩短速率分别为 2 5 6mm/a和 2 2 9mm/a 相似文献
6.
南天山及塔里木北缘构造带位于帕米尔地区东北侧,地震活动强烈。文中通过地质构造剖面、深部探测资料和地震震源机制解资料,综合研究了该区的地震构造模型。结果认为,该区的构造活动主要表现为天山地块逆冲于塔里木地块之上。天山构造系统包括迈丹断裂及其前缘推覆构造;塔里木构造系统包括深部的塔里木北缘断裂、基底共轭断层和浅部的推覆构造。塔里木北缘断裂是发育于塔里木地壳内部的高角度断裂,其形成原因在于塔里木和天山构造变形方向的差异。塔里木北缘断裂为研究区大地震的主要发震构造,天山推覆构造和塔里木基底断裂系统均具有不同性质的中强地震发震能力 相似文献
7.
天山的晚新生代构造变形及其地球动力学问题 总被引：73，自引：6，他引：73
天山是大陆内部典型的新生代复活造山带，其新生代构造变形的方式，变形量，速度及过程等对于认识大陆内部造山带的变形机理有着重要的意义。本文在对南北天山主要活动构造地质填图和综合研究的基础上，重点探讨了天山的晚新生代构造变形特征及其动力学问题。早更新世以来，特别是早，中更新世之间，天山的构造活动由内部向南北两侧扩展，使得两侧的新生代凹陷逐渐褶皱成山，形成数排新生代褶皱带，整个天山的现代构造活动是一种扇形 相似文献
8.
RESEARCH ON NEOGENE-QUATERNARY STRATIGRAPHIC STRUCTURE AND SHALLOW TECTONIC FEATURES IN THE NORTH SECTION OF DAXING FAULT ZONE BASED ON SHALLOW SEISMIC REFLECTION PROFILING 
下载免费PDF全文
下载免费PDF全文 HE Fu-bing XU Xi-wei HE Zhen-jun ZHANG Xiao-liang LIU Li-yan ZHANG Wei WEI Bo NI Jing-bo 《地震地质》1979,42(4):893-908
The Daxing Fault is an important buried fault in the Beijing sub-plain, which is also the boundary fault of the structural unit between Langgu sub-sag and Daxing sub-uplift. So far, there is a lack of data on the shallow tectonic features of the Daxing Fault, especially for the key structural part of its northern section where it joins with the Xiadian Fault. In this paper, the fine stratigraphic classifications and shallow tectonic features of the northern section in the main Daxing Fault are explored by using three NW-trending shallow seismic reflection profiles. These profiles pass through the Daxing earthquake(M6¾)area in 1057AD and the northern section of the main Daxing Fault. The results show that seven strong reflection layers(T01—T03, TQ and T11—T13)are recognized in the strata of Neogene and Quaternary beneath the investigated area. The largest depth of strong reflection layer(T13)is about 550~850ms, which is interpreted as an important surface of unconformity between Neogene and Paleogene or basement rock. The remaining reflection layers, such as T01 and TQ, are interpreted as internal interfaces in Neogene to Quaternary strata. There are different rupture surfaces and slip as well as obviously different structural features of the Daxing Fault revealed in three shallow seismic reflection profiles. The two profiles(2-7 and 2-8)show obvious rupture surfaces, which are the expression of Daxing Fault in shallow strata. Along the profile(2-6), which is located at the end of the Daxing fault structure, a triangle deformation zone or bending fracture can be identified, implying that the Daxing Fault is manifested as bending deformation instead of rupture surfaces at its end section. This unique structural feature can be explained by a shearing motion at the end of extensional normal fault. Therefore, the Daxing Fault exhibits obviously different tectonic features of deformation or displacement at different structural locations. The attitude and displacement of the fault at the shallow part are also different to some extent. From the southwest section to the northeast section of the fault, the dip angle gradually becomes gentler(80°~60°), the upper breakpoint becomes deeper(160~600m), and the fault displacement in Neogene to Quaternary strata decreases(80~0m). Three shallow seismic reflection profiles also reveal that the Daxing Fault is a normal fault during Neogene to early Quaternary, and the deformation or displacement caused by the activity of the fault reaches the reflection layer T02. This depth is equivalent to the sedimentary strata of late Early-Pleistocene. Therefore, the geometry and morphology of the Daxing Fault also reveal that the early normal fault activity has continued into the Early Pleistocene, but the evidence of activity is not obvious since the late Pleistocene. The earthquakes occurring along the Daxing Fault, such as Daxing earthquake(M6¾)in 1057AD, may not have much relation with this extensional normal fault, but with another new strike-slip fault. A series of focal mechanism solutions of modern earthquakes reveal that the seismic activity is closely related to the strike-slip fault. The Daxing Fault extends also downwards into the lower crust, and may be cut by the steeply dipping new Xiadian Fault on deep seismic reflection profile. The northern section of the Daxing Fault strikes NNE, with a length of about 23km, arranged in a right step pattern with the Xiadian Fault. Transrotational basins have been developed in the junction between the northern Daxing Fault and the southern Xiadian Fault. Such combined tectonic features of the Daxing Fault and Xiadian Fault evolute independently under the extensional structure background and control the development of the Langgu sub-sag and Dachang sub-sag, respectively. 相似文献
9.
通过对天山北麓 190 6年玛纳斯 7 7级地震区的浅层地震探测资料、石油地震反射剖面、二维电性结构剖面、深地震反射剖面的研究 ,发现玛纳斯地震区多层次活动构造系统的根带 ,它通过脆 -韧转换带与天山活动构造块体内上地壳中的低速、高导层连为一体。低速、高导层可能是天山地壳内正在活动的韧性剪切带 ,而齐古逆断裂 -褶皱带下的脆 -韧转换带是连接深部活动韧性剪切带与地壳浅部脆性破裂的枢纽 ,也是现今孕育和发生大地震的重要构造部位。 190 6年玛纳斯地震发生在脆韧转换带的底部 ,地震区的活动逆断裂和褶皱只是部分记录了深部韧性剪切带活动的信息 相似文献
10.
柯坪逆冲推覆构造带是西南天山山前晚新生代以来形成的活动逆断裂-褶皱带,由5~6排近平行的弧形褶皱带组成,出露地层为寒武系—第四系。背斜形态多为复式箱状背斜和不对称的斜歪背斜,分别与断层弯曲背斜和断层扩展背斜的几何形态一致。地震勘探资料显示,各褶皱带前缘活动逆断裂在深部归并于统一的、由寒武系中的石膏层组成的滑脱面。滑脱面深度具有南浅北深、东浅西深的特点,皮羌断裂西侧滑脱面深度约为9km,东侧滑脱面深度为5km。在柯坪逆冲推覆构造中部的皮羌断裂东西两侧各5km和8km的位置,以断层弯曲褶皱和断层扩展褶皱构造模型为指导,用线长平衡的方法完成了2条长度分别为78km和73km的平衡地质剖面,恢复到变形前的形态后计算出这2条剖面上的地壳缩短量分别为40km和45km,缩短率为33%和37%。由于对柯坪逆冲推覆构造开始形成时间的证据较少,所以要计算长期的缩短速率是比较困难的。对比天山南麓库车活动逆断裂-褶皱带的形成时代,以及柯坪逆冲推覆构造与印干断裂的关系,认为柯坪逆冲推覆构造形成于第四纪早期的西域砾岩沉积阶段,按距今2.5Ma计算,柯坪逆冲推覆构造的地壳缩短速率是15.4~17.3mm/a 相似文献
11.
12.
天山山前主要推覆构造区的地壳缩短 总被引：19，自引：11，他引：8
利用平衡地质剖面方法研究天山山前主要褶皱带的地壳缩短,其中3条平衡剖面分别横跨天山南簏的柯坪逆断裂-褶皱带和库车逆断裂-褶皱带,2条剖面横跨天山北簏的玛纳斯活动逆断裂-褶皱带,其余1条剖面横跨吐鲁番中央隆起逆断裂-褶皱带。柯坪活动逆断裂-褶皱带、库车逆断裂-褶皱带、玛纳斯逆断裂-褶皱带和吐鲁番盆地的地壳缩短量分别为40~45km、27~37km、8·5~10·5km和6~7km。天山山前活动逆断裂-褶皱带在EW向上互不重叠,它们的缩短量大致代表了该经度上新生代的最小地壳缩短量,反映出天山地壳缩短由西向东减小的趋势。假定天山山前活动逆断裂-褶皱带开始形成的时间为距今2·5Ma的西域砾岩沉积期,考虑到博阿断裂、塔拉斯-费尔干纳断裂在SN向上的缩短活动分量,上述4个地段的最小缩短速率分别为15·4~17·3mm/a、12·7~16·5mm/a、3·8~4·5mm/a和2·3~2·7mm/a。活动走滑断裂在天山内部特定位置向左偏转,走向由NW转为NWW,在断裂转折的部位走滑活动量转化为天山SN向的缩短变形 相似文献
13.
FOCAL MECHANISM SOLUTION AND TECTONIC STRESS FIELD CHARACTERISTICS OF THE MIDDLE TIANSHAN MOUNTAINS,XINJIANG 下载免费PDF全文
下载免费PDF全文 ZHANG Zhi-bin ZHAO Xiao-cheng REN Lin 《地震地质》1979,42(3):595-611
The middle part of the Tianshan Mountains in Xinjiang is located in the north-central part of the Tianshan orogenic belt, between the rigid Tarim Basin and Junggar Basin. It is one of the regions with frequent deformation and strong earthquake activities. In this paper, 492 MS>2.5 earthquake events recorded by Xinjiang seismograph network from 2009 to 2018 were collected. The MS3.5 earthquake was taken as the boundary, the focal mechanism solutions of the earthquake events in this region were calculated by CAP method and FOCEMEC method respectively. At the same time the focal mechanism solutions of GCMT recorded historical earthquake events in this region were also collected. According to the global stress map classification standard, the moderate-strong earthquakes in the region are mainly dominated by thrust with a certain slip component, which are distributed near the combined belts of the Tarim Basin, Junggar Basin, Turpan Basin and Yili Basin with Tianshan Mountains. The thrust component decreases from south to north, while the strike-slip component increases. The spatial distribution characteristics of the tectonic stress field in the middle section of the Tianshan Mountains in Xinjiang are obtained by using the damped regional-scale stress field inversion method. The maximum principal compressive stress in axis the study area rotated in a fan shape from west to east, the NW direction in the western section gradually shifted to NE direction, its elevation angle is nearly horizontal, in the state of near horizontal compression. The minimum principal compressive stress axis is nearly EW, and the elevation angle is nearly vertical. Influenced by large fault zones such as Kashi River, Bolhinur, Nalati, Fukang, the southern margin of the Junggar and the north Beiluntai, the local regional stress field presents complex diversity. Under the influence of the northward extrusion of Pamir and Tarim blocks, the whole Tianshan is shortened by compression, but its shortening rate decreases from south to north and from west to east, the stress shape factor increases gradually from west to east, the intermediate principal compressive stress axis exhibits a change in compression to extension. There are some differences in the characteristics of tectonic stress field between the north and south of Tianshan Mountains. The regional maximum principal compressive stress axis is 15° north by east on the south side, while it is nearly NS on the north side. The deformation of the Tianshan Mountains and the two basins on both sides is obviously larger than that in the inside of the mountain. Changes in the crustal shortening rate caused by the rotation of the rigid Tarim block and Junggar block to the relatively soft Tianshan block, as well as the uplifts of Borokonu and Bogda Mountains, the comprehensive influence of the material westward expansion constitute the stress field distribution characteristics of the north and south sides of the middle section of Tianshan Mountains. The recent two MS6.6 earthquakes in the region caused the regional stress field to rotate counterclockwise. The post-earthquake stress field and the main source focal mechanism solution tend to be consistent. The seismic activity in the study area is week in the south and strong in the north. The focal depth is about 20km. Most strike-slip earthquakes occur near the junction belt of the Tianshan and Junggar Basin. 相似文献
14.
THREE-DIMENSIONAL STRUCTURAL FEATURES OF THE PENGXIAN ACTIVE BLIND FAULT IN THE CENTRAL LONGMEN SHAN FRONT BELT 下载免费PDF全文
下载免费PDF全文 WANG Zhen-nan LU Ren-qi XU Xi-wei HE Deng-fa CAI Ming-gang LI Ying-qiang LUO Jia-hong 《地震地质》2019,41(4):944-959
The Pengxian blind fault is a typical active fault in the central Longmen Shan front belt. It has important reference value for understanding the growth mode and process of the eastern Tibetan plateau. Because the fault is covered by the thick Upper Cenozoic strata in the western Sichuan Basin, its three-dimensional spatial distribution, structural style and formation mechanism remain unclear. In this paper, based on several high-resolution 3-D seismic reflection profiles, together with near-surface geological data and borehole data, we investigate the structural geometry of the Pengxian blind fault and build a 3-D model based on the results. We analyze the shape and scale of underground spatial distribution of the fault through a three-dimensional fault model. According to the theory of fault-related fold and fold-accommodation fault, this paper discusses the forming mechanism of the Pengxian buried structures. The shallow tectonic deformation in front of Longmen Shan is closely related to the detachment layer of the Middle and Lower Triassic, and this detachment layer f1 horizontally propagates into the Longquanshan anticline in the western Sichuan Basin. The Pengxian buried fault is a typical fault-bend fold and the f1 horizontally propagates into the western Sichuan Basin with a fault slip of 3.5km. The Pengxian blind fault is a high angle(50°~60°)thrust fault developed in the front wing of the kink-band zone, striking NE-SW, with a total length of~50km; But the fault is not connected with the Dayi buried fault in the south section of Longmen Shan. They are two different faults, and this defines the scale of the Pengxian blind fault. This limitation makes sense for analyzing and evaluating the magnitudes of potential earthquake. All above study provides research basis for further analysis of the potential seismic risk in this area. The Pengxian blind fault is parallel to the anticlinal axis with small amount of offset as a fold-accommodation fault. We believe that the fault formation is related to the fold deformation of the fold front limb. The study reveals the geometry, kinematics and formation mechanism of the Pengxian active fault, and provides a basis for further analysis of fault activity and hazard. Therefore, there is little possibility of strong earthquakes at the Pengxian blind fault due to its formation mechanism of the fault which is generally characterized by fold deformation and shortening deformation. In this paper, we discuss the location of Pengxian blind fault in the middle of Longmen Shan and Sichuan Basin. Because the Pengxian buried structures are in the transition area, the shortening amount in Pengxian indicates that the absorption in the basin is quite limited. It reflects the blocking effect of Sichuan Basin. In the study, we find that the relationship between folds, faults and sediments is an important part of tectonic interpretation; the theory of fault-related fold and fold-accommodation fault is well used for analysis. This would have great significance for the study of structural deformation, which can help to build a three-dimensional model of fault. 相似文献
15.
THE CENOZOIC TECTONICS AND SEISMIC ACTIVITY OF XINZHENG-TAIKANG FAULT IN THE SOUTHERN EDGE OF TAIKANG AREA 下载免费PDF全文
下载免费PDF全文 On the basis of dividing and comparison of the Neogene strata and their bottoms revealed by 7 drill holes in Taikang area, we completed 101 seismic profiles with a total length of 4991km. Seismic data were compared and interpreted. The results indicate that Xinzheng-Taikang Fault, as a blind fault extending from Xinzheng to Taikang, which was considered as an EW striking fault from Xuchang to Taikang before, is the boundary of Taikang uplift and Zhoukou depression, controlling the sedimentation since Neogene Period. So we named the fault the Xinzheng-Taikang Fault, which is composed of two branches, mainly, the east and west branches. The west branch strikes northwest, dipping northeast with steep angles, and the fault plane extending more than 140km in length. As revealed on the seismic profiles, the eastern segment of the west branch is normal fault, while the west segment of the branch shows characteristics of strike-slip fault. The east branch trends NW-NEE, dipping SW-SSE with the length of about 50km. Two branches form a minus flower structure, indicating the strike slip-extension tectonic background. The bottom of Neogene strata is offset about 120m by the east branch, 20m by the west branch, and the bottom of Quaternary is probably offset too. Meanwhile, latest studies suggest that the composite strip of the two branches of Xinzheng-Taikang Fault, which is a tectonic transfer zone, is the subduction zone between the two strike-slip faults. The tectonic stress tends to be released by the east-west branch fault, and the zone should be the seismogenic structure for the recent seismicity in Taikang area. In 2010, the latest earthquake ofMS4.7 occurred in this area, causing 12 people wounded. The seismogenic structure was considered to be the Xinzheng-Taikang Fault. So locating the fault exactly is of great importance to disaster prevention. 相似文献
16.
塔里木盆地新疆喀什以西部分是西南天山和帕米尔两大对冲构造系统的会聚带,关于两者变形前缘和分界的确切位置存在不同认识.在乌恰县以南的玛依卡克盆地南缘,清晰可见属于帕米尔构造带、向N或NNE逆冲的帕米尔前缘逆冲推覆体(PFT).最近野外调查在盆地北部发现了西南天山前缘的最新变形带:向南逆冲的乌拉根背斜南翼断层.断层总体近E... 相似文献
17.
The Bolokenu-Aqikekuduk fault zone(B-A Fault)is a 1 000km long right-lateral strike-slip active fault in the Tianshan Mountains. Its late Quaternary activity characteristics are helpful to understand the role of active strike-slip faults in regional compressional strain distribution and orogenic processes in the continental compression environment, as well as seismic hazard assessment. In this paper, research on the paleoearthquakes is carried out by remote sensing image interpretation, field investigation, trench excavation and Quaternary dating in the Jinghe section of B-A Fault. In this paper, two trenches were excavated on in the pluvial fans of Fan2b in the bulge and Fan3a in the fault scarp. The markers such as different strata, cracks and colluvial wedges in the trenches are identified and the age of sedimentation is determined by means of OSL dating for different strata. Four most recent paleoearthquakes on the B-A Fault are revealed in trench TC1 and three most recent paleoearthquakes are revealed in trench TC2. Only the latest event was constrained by the OSL age among the three events revealed in the trench TC2. Therefore, when establishing the recurrence of the paleoearthquakes, we mainly rely on the paleoearthquake events in trench TC1, which are labeled E1-E4 from oldest to youngest, and their dates are constrained to the following time ranges: E1(19.4±2.5)~(19.0±2.5)ka BP, E2(18.6±1.4)~(17.3±1.4)ka BP, E3(12.2±1.2)~(6.6±0.8)ka BP, and E4 6.9~6.2ka BP, respectively. The earthquake recurrence intervals are(1.2±0.5)ka, (8.7±3.0)ka and(2.8±3)ka, respectively. According to the sedimentation rate of the stratum, it can be judged that there is a sedimentary discontinuity between the paleoearthquakes E2 and E3, and the paleoearthquake events between E2 and E3 may not be recorded by the stratum. Ignoring the sedimentary discontinuous strata and the earthquakes occurring during the sedimentary discontinuity, the earthquake recurrence interval of the Jinghe section of B-A Fault is ~1~3ka. This is consistent with the earthquake recurrence interval(~2ka)calculated from the slip rate and the minimum displacement. The elapsed time of the latest paleoearthquake recorded in the trench is ~6.9~6.2ka BP. The magnitude of the latest event defined by the single event displacement on the fault is ~MW7.4, and a longer earthquake elapsed time indicates the higher seismic risk of the B-A Fault. 相似文献
18.
位于龙门山逆冲推覆构造带东侧的龙泉山背斜,构成了四川前陆盆地的前陆隆起。通过室内航空相片对凯江跨背斜段的地貌面的解译,结合野外考察可知凯江发育3级阶地,其中T1、T2为堆积阶地,T3为基座阶地。在野外用差分GPS测量了阶地的空间坐标信息,同时采集了各级阶地堆积物的测年样本,并经实验分析约束了阶地的形成年龄。另外,对石油地震剖面解译揭示出龙泉山背斜北段地壳缩短和隆升主要是通过褶皱膝折带迁移机制进行的,滑脱层的深度约6km。利用面积守恒准则计算出龙泉山背斜晚更新世以来的地壳缩短速率约为(1.36±0.41)mm/a、隆升速率为(0.64±0.19)mm/a。通过滑脱层的推覆抬升机制形成的龙泉山背斜,给青藏高原东缘变形模式中的逆断层推覆地壳缩短造山增加了证据。 相似文献
19.
浅析北天山西段与南天山中东段地震活动关系 总被引：1，自引：0，他引：1
对比分析了北天山西段与南天山中东段的地震活动关系,发现1935年以来两区地震活动水平相近,中强以上地震具有交替活动的特征,且有一定的成组性南北迁移的规律。时空扫描分析发现,北天山西段新源—温泉附近地区的中小地震集中活动对南天山东段中强地震的发生具有一定的前兆意义,南天山东段的4级地震频度的减小与北天山西段5级以上地震有一定的对应关系。并在一定程度上对两区域地震活动存在的以上规律和对应关系进行了分析。 相似文献
20.
以中国西北地区的地震层析成像为基础,研究了天山地震带深部结构的基本特征．结果表明,天山地震带的地壳中部为低速的韧性滑脱层,南天山的断裂深度超过莫霍面,北天山的断裂深度一般只到地壳中部;天山莫霍面的深度一般大于５０ｋｍ,壳－幔边界由宽而缓的速度过渡带构成,中强地震主要位于盆山边界地壳中下部位波速变化较大的区域．帕米尔、南天山和塔里木之间存在一个北北东方向的低速带,乌恰和伽师地震分别位于该低速带东、西两侧的梯度带附近．推测帕米尔、南天山和塔里木之间的相对运动是导致低速带内部物质发生形变并在边界附近产生破裂的主要原因,地幔热物质的侵入对该地区的构造活动起到了重要的动力学作用． 相似文献