共查询到20条相似文献，搜索用时 15 毫秒
1.
从板式橡胶支座及混凝土挡块抗震设计角度,以一座典型的3跨预应力混凝土连续梁桥为例,结合概率地震需求分析及桥墩、支座等抗震关键构件极限破坏状态,建立不同支座及挡块分析模型的中小跨径梁桥地震易损性曲线,研究考虑支座滑移效应及挡块破坏的中小跨径梁桥的易损性特征。研究结果表明:不考虑橡胶支座的滑移效应及混凝土挡块破坏,桥墩地震破坏概率明显增大,且会低估支座破坏概率;桥梁系统易损性受支座破坏状态的影响显著,需设置合理的限位装置;在中小跨径梁桥地震易损性分析中,考虑支座的滑移效应及混凝土挡块的破坏十分必要。 相似文献
2.
3.
Damage investigation of small to medium-span highway bridges in Wenchuan earthquake revealed that typical damage of these bridges included: sliding between laminated-rubber bearings and bridge girders, concrete shear keys failure, excessive girder displacements and even span collapse. However, the bearing sliding could actually act as a seismic isolation for piers, and hence, damage to piers for these bridges was minor during the earthquake. Based on this concept, an innovative solation system for highway bridges with laminated-rubber bearings is developed. The system is comprised of typical laminated-rubber bearings and steel dampers. Bearing sliding is allowed during an earthquake to limit the seismic forces transmitting to piers, and steel dampers are applied to restrict the bearing displacements through hysteretic energy dissipation. As a major part of this research, a quarter-scale, two-span bridge model was constructed and tested on the shake tables to evaluate the performance of this isolation system. The bridge model was subjected to a Northridge and an artificial ground motion in transverse direction. Moreover, numerical analyses were conducted to investigate the seismic performance of the bridge model. Besides the test bridge model, a benchmark model with the superstructure fixed to the substructure in transverse direction was also included in the numerical analyses. Both the experimental and the numerical results showed high effectiveness of this proposed isolation system in the bridge model. The system was found to effectively control the pier-girder relative displacements, and simultaneously, protect the piers from severe damage. Numerical analyses also validated that the existing finite element methods are adequate to estimate the seismic response of bridges with this isolation system. 相似文献
4.
为研究不同设计参数对曲线梁桥地震响应的影响以指导结构抗震设计,对不同支承约束曲线梁桥地震响应及地震需求敏感性进行分析。采用增量动力分析（IDA）方法对比分析了不同支承约束曲线梁桥的结构地震响应变化趋势;采用Tornado图形法对不同结构参数影响程度进行了排序,找出了对结构地震需求影响显著的参数。结果表明:采用板式橡胶支座桥梁因支座易发生滑移而导致上部结构位移较大,但降低了下部结构响应,设置固定墩后,下部结构损伤显著增加;对于采用板式橡胶支座和铅芯橡胶支座的曲线梁桥,墩高及跨径对墩底曲率需求影响较大,而对于固定墩为墩梁固结形式和采用盆式橡胶支座的曲线梁桥,跨径及跨数对墩底曲率需求影响较大;对于采用不同支承约束的曲线梁桥,墩高和曲率半径对桥台位移需求影响较大,仅次于地震动参数PGA。 相似文献
5.
为了提高中小跨径简支梁桥的抗震能力,促进多级抗震设计思想的完善,以汶川地震中的寿江大桥为背景,构建了支座-挡块-桥墩相互作用分析模型,采用增量动力分析（IDA）方法,以挡块强度和墩高作为变化参数,研究了支座滑移、挡块限位和桥墩塑性三者之间抗震性能状态的耦合关系。研究表明:提高挡块强度可有效地控制支座的滑移,但会增大桥墩的曲率延性系数,且桥墩越矮,曲率延性系数增长越快;随着挡块强度的变化,支座滑移比的变化幅度明显大于桥墩曲率延性系数;随着墩高的增大,挡块的相对限位能力会提高;对于中小跨径简支梁桥而言,理想的抗震状态为:允许挡块破坏,使得支座出现小幅滑移,桥墩出现可修复的塑性损伤。因此,在挡块设计中,可优先考虑支座的限位效果,再综合考虑桥墩的地震响应,当桥墩为矮墩时,挡块的设计强度不可过大。 相似文献
6.
Evgueni T. Filipov Jessica R. Revell Larry A. Fahnestock James M. LaFave Jerome F. Hajjar Douglas A. Foutch Joshua S. Steelman 《地震工程与结构动力学》2013,42(9):1375-1394
Modern highway bridges in Illinois are often installed with economical elastomeric bearings that allow for thermal movement of the superstructure, and steel fixed bearings and transverse retainers that prevent excessive movement from service‐level loadings. In the event of an earthquake, the bearing system has the potential to provide a quasi‐isolated response where failure of sacrificial elements and sliding of the bearings can cause a period elongation and reduce or cap the force demands on the substructure. A computational model that has been calibrated for the expected nonlinear behaviors is used to carry out a parametric study to evaluate quasi‐isolated bridge behavior. The study investigates different superstructure types, substructure types, substructure heights, foundation types, and elastomeric bearing types. Overall, only a few bridge variants were noted to unseat for design‐level seismic input in the New Madrid Seismic Zone, indicating that most structures in Illinois would not experience severe damage during their typical design life. However, Type II bearing systems, which consist of an elastomeric bearing and a flat PTFE slider, would in some cases result in critical damage from unseating at moderate and high seismic input. The sequence of damage for many bridge cases indicates yielding of piers at low‐level seismic input. This is caused by the high strength of the fixed bearing element, which justifies further calibration of the quasi‐isolation design approach. Finally, the type of ground motion, pier height, and bearing type were noted to have significant influence on the global bridge response. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
7.
Seismic pounding between adjacent frames in multiple-frame bridges and girder ends in multi-span simply supported bridges has been commonly observed in several recent earthquakes. The consequences of pounding include damage to piers, abutments, shear keys, bearings and restrainers, and possible collapse of deck spans. This paper investigates pounding in bridges from an analytical perspective. A simplified nonlinear model of a multiple-frame bridge is developed including the effects of inelastic frame action and nonlinear hinge behavior, to study the seismic response to longitudinal ground motion. Pounding is implemented using the contact force-based Kelvin model, as well as the momentum-based stereomechanical approach, Parameter studies are conducted to determine the effects of frame period ratio, column hysteretic behavior, energy dissipation during impact and near source ground motions on the pounding response of the bridge. The results indicate that pounding is most critical for highly out-of-phase frames and is not significant for frame period ratios greater than 0.7. Impact models without energy dissipation overestimate the displacement and acceleration amplifications due to impact, especially for elastic behavior of the frames. Representation of stiffness degradation in bridge columns is essential in capturing the accurate response of pounding frames subjected to far field ground motion. Finally, it is shown that strength degradation and pounding can result in significant damage to the stiffer frames of the bridge when subjected to large acceleration pulses from near field ground motion records. 相似文献
8.
不同约束方式对匝道桥动力特性的影响研究 总被引：1，自引：0，他引：1
近年来,地震作用下的匝道桥表现出较高的地震易损性。为建立匝道桥的有效约束方式,以减小其地震损伤,本文基于汶川地震中连续梁桥约束方式的调研结果,建立了4种不同匝道桥支座约束方式,并以石家庄石环线某匝道桥为例,对比分析了不同约束方式下匝道桥的自振特性及地震响应。结果表明:板式橡胶支座具有一定的剪切变形能力,可降低桥墩与支座组成的体系刚度,有效分散了上部结构的地震惯性力,保护了下部结构,但应注意其引起的较大主梁位移;固定支座或墩梁固结形式会放大桥墩受力,增加下部结构的损坏,不宜设置在高度较矮、刚度较大的桥墩上;双层挡块和垫石凹槽分级限位支座具有较好的限位能力,并可耗散部分地震能量。 相似文献
9.
Implications of seismic pounding on the longitudinal response of multi-span bridges - an analytical perspective 总被引：2，自引：0，他引：2
ReginaldDesRoches SusendarMuthukumar 《地震工程与工程振动(英文版)》2004,3(1):57-65
Seismic pounding between adjacent frames in multiple-frame bridges and girder ends in multi-span simply supported bridges has been commonly observed in several recent earthquakes. The consequences of pounding include damage to piers, abutments, shear keys, bearings and restrainers, and possible collapse of deck spans. This paper investigates pounding in bridges from an analytical perspective. A simplified nonlinear model of a multiple-frame bridge is developed including the effects of inelastic frame action and nonlinear hinge behavior, to study the seismic response to longitudinal ground motion. Pounding is implemented using the contact force-based Kelvin model, as well as the momentum-based stereomechanical approach. Parameter studies are conducted to determine the effects of frame period ratio, column hysteretic behavior, energy dissipation during impact and near source ground motions on the pounding response of the bridge. The results indicate that pounding is most critical for highly out-of-phase frames and is not significant for frame period ratios greater than 0.7. Impact models without energy dissipation overestimate the displacement and acceleration amplifications due to impact, especially for elastic behavior of the frames. Representation of stiffness degradation in bridge columns is cssential in capturing the accurate response of pounding frames subjected to far field ground motion. Finally, it is shown that strength degradation and pounding can result in significant damage to the stiffer frames of the bridge when subjected to large acceleration pulses from near field ground motion records. 相似文献
10.
为了提高采用板式橡胶支座的斜梁桥横向抗震能力,揭示其在不同设计参数下的横向抗震行为,考虑板式橡胶支座的滑移、钢筋混凝土挡块的滞回力学性能、桥台-背土效应等非线性因素,采用OpenSEES建立某连续斜梁桥的三维分析模型,提出支座位移评价指标、主梁平面转角指标、墩柱曲率延性指标和抗剪指标,研究不同挡块强度和间隙组合下桥梁的横向抗震性能。研究表明:同时增大挡块强度和间隙,总体上会降低支座的横向变形,但会增加其纵向变形;挡块强度越高,主梁的横向位移有所下降,但平面转角越大,对两侧桥台处的支座抗剪越不利;挡块强度越高,间隙越小,墩柱越有可能进入弹塑性状态。在本文桥例中,当挡块强度取40%支反力,间隙取0.08m时,所有抗震指标都可满足规范要求。 相似文献
11.
E. Tubaldi S. A. Mitoulis H. Ahmadi A. Muhr 《Bulletin of Earthquake Engineering》2016,14(4):1285-1310
This paper investigates the potential tensile loads and buckling effects on rubber-steel laminated bearings on bridges. These isolation bearings are typically used to support the deck on the piers and the abutments and reduce the effects of seismic loads and thermal effects on bridges. When positive means of fixing of the bearings to the deck and substructures are provided using bolts, the isolators are exposed to the possibility of tensile loads that may not meet the code limits. The uplift potential is increased when the bearings are placed eccentrically with respect to the pier axis such as in multi-span simply supported bridge decks. This particular isolator configuration may also result in excessive compressive loads, leading to bearing buckling or in the attainment of other unfavourable limit states for the bearings. In this paper, an extended computer-aided study is conducted on typical isolated bridge systems with multi-span simply-supported deck spans, showing that elastomeric bearings might undergo tensile stresses or exhibit buckling effects under certain design situations. It is shown that these unfavourable conditions can be avoided with the rational design of the bearing properties and in particular of the shape factor, which is the geometrical parameter controlling the axial bearing stiffness and capacity for a given shear stiffness. Alternatively, the unfavourable conditions could be reduced by reducing the flexural stiffness of the continuity slab. 相似文献
12.
Design formulas for supplemental viscous dampers to building structures are readily available in FEMA provisions and MCEER research reports. However, for the design of supplemental viscous dampers corresponding to a desired system damping ratio of highway bridges, there exist, if any, few design guidelines. This is particularly true if the bridge components such as elastomeric bearings, piers and abutment possess different damping ratios, stiffnesses, and lumped masses. In this paper, the design formulas for supplemental viscous dampers to highway bridges have been derived based on the concept of ‘composite damping ratio’. The design formulas can be used to determine the damping coefficients of the dampers corresponding to a desired system damping ratio of the bridge in which different component damping ratios may be assumed for the elastomeric bearings, piers and abutments. The proposed design formulas are numerically validated by comparing the seismic responses of a three‐span bridge equipped with viscous dampers with those of the same bridge without viscous dampers but with an assigned inherent system damping ratio equal to the target system damping ratio. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
13.
Shear keys are used in the bridge abutments and piers to provide transverse restraints for bridge superstructures. Owing to the relatively small dimensions compared to the main bridge components (girders, piers, abutments, piles), shear keys are normally regarded as secondary component of a bridge structure, and their influences on bridge seismic responses are normally neglected. In reality, shear keys are designed to restrain the lateral displacements of bridge girders, which will affect the transverse response of the bridge deck, thus influence the overall structural responses. To study the influences of shear keys on bridge responses to seismic ground excitations, this paper performs numerical simulations of the seismic responses of a two-span simply-supported bridge model without or with shear keys in the abutments and the central pier. A detailed 3D finite element (FE) model is developed by using the explicit FE code LS-DYNA. The bridge components including bridge girders, piers, abutments, bearings, shear keys and reinforcement bars are included in the model. The non-linear material behaviour including the strain rate effects of concrete and steel rebar are considered. The seismic responses of bridge structures without and with shear keys subjected to bi-axial spatially varying horizontal ground motions are calculated and compared. The failure mode and damage mechanism of shear keys are discussed in detail. Numerical results show that shear keys restrain transverse movements of bridge decks, which influence the torsional–lateral responses of the decks under bi-axial spatially varying ground excitations; neglecting shear keys in bridge response analysis may lead to inaccurate predictions of seismic responses of bridge structures. 相似文献
14.
Many highway bridges were severely damaged or completely collapsed during the 2008 Wenchuan earthquake.A field investigation was carried out in the strongly affected areas and over 320 bridges were examined. Damage to some representative highway bridges is briefly described and a preliminary analysis of the probable causes of the damage is presented in this paper. The most common damage included shear-flexural failure of the pier columns, expansion joint failure, shear key failure, and girder sliding in the transversal or longitudinal directions due to weak connections between girder and bearings. Lessons learned from this earthquake are described and recommendations related to the design of curved and skewed bridges, design of bearings and devices to prevent girder collapse, and ductility of bridge piers are presented.Suggestions for future seismic design and retrofitting techniques for bridges in moderate to severe earthquake areas are also proposed. 相似文献
15.
在地震作用下中小跨径梁桥横向易出现落梁以及桥墩破坏。为了防止桥梁出现上述震害,提出以楔形挡块作为限位装置来提升桥梁的横向抗震性能。以一座3×20 m连续混凝土梁桥为例,通过OpenSees软件来建立有限元模型,在考虑板式橡胶支座的摩擦滑移效应、钢筋混凝土桥墩的非线性等力学效应的情况下,对其进行动力时程分析。引入主梁位移响应、桥墩顶部最大位移响应等作为指标,用柔性挡块、刚性挡块两种工况来与楔形挡块进行对比分析,并且分析楔形挡块不同角度对位移响应的影响。结果表明:楔形挡块角度设置合适时能够有效约束梁体位移响应,并且不显著提高桥墩顶部的位移响应。 相似文献
16.
The nuclear accident at Fukushima Daiichi in March 2011 has led the nuclear community to consider seismic isolation for new large light water and small modular reactors to withstand the effects of beyond design basis loadings, including extreme earthquakes. The United States Nuclear Regulatory Commission is sponsoring a research project that will quantify the response of low damping rubber (LDR) and lead rubber (LR) bearings under loadings associated with extreme earthquakes. Under design basis loadings, the response of an elastomeric bearing is not expected to deviate from well‐established numerical models, and bearings are not expected to experience net tension. However, under extended or beyond design basis shaking, elastomer shear strains may exceed 300% in regions of high seismic hazard, bearings may experience net tension, the compression and tension stiffness will be affected by isolator lateral displacement, and the properties of the lead core in LR bearings will degrade in the short‐term because of substantial energy dissipation. New mathematical models of LDR and LR bearings are presented for the analysis of base isolated structures under design and beyond design basis shaking, explicitly considering both the effects of lateral displacement and cyclic vertical and horizontal loading. These mathematical models extend the available formulations in shear and compression. Phenomenological models are presented to describe the behavior of elastomeric isolation bearings in tension, including the cavitation and post‐cavitation behavior. The elastic mechanical properties make use of the two‐spring model. Strength degradation of LR bearing under cyclic shear loading due to heating of lead core is incorporated. The bilinear area reduction method is used to include variation of critical buckling load capacity with lateral displacement. The numerical models are coded in OpenSees, and the results of numerical analysis are compared with test data. The effect of different parameters on the response is investigated through a series of analyses. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
17.
For the purpose of accurately predicting the seismic response of base-isolated structures, an analytical hysteresis model for elastomeric seismic isolation bearings is proposed. An extensive series of experimental tests of four types of seismic isolation bearings—two types of high-damping rubber bearings, one type of lead-rubber bearing and one type of silicon rubber bearing—was carried out with the objective of fully identifying their mechanical characteristics. The proposed model is capable of well-predicting the mechanical properties of each type of elastomeric bearing into the large strain range. Earthquake simulator tests were also conducted after the loading tests of the individual bearings. In order to show the validity of the proposed model, non-linear dynamic analyses were conducted to simulate the earthquake simulator test results. Good agreement between the experimental and analytical results shows that the model can be an effective numerical tool to predict not only the peak response value but also the force–displacement relationship of the isolators and floor response spectra for isolated structures. © 1997 by John Wiley & Sons, Ltd. 相似文献
18.
José M. Jara Dorian Villanueva Manuel Jara Bertha A. Olmos 《Bulletin of Earthquake Engineering》2013,11(2):663-686
Bridge structures are usually built on irregular topographical surfaces which create substructures with different pier heights and non uniform stiffness distribution. Three irregularity types of typical reinforced concrete (RC) medium length bridges located in a high seismicity zone of Mexico, were analyzed aimed at determining the best strength and stiffness parameters of an isolation system. The isolation system is composed by lead rubber bearings (LRB) located on each pile and abutment. The variation of the bridge characteristics and the isolation parameters produced 169 models that were subjected to ten seismic records representative of the subduction zone in the Pacific Coast of Mexico. A total of 1690 nonlinear time history analyses (NLTHA) were carried out in longitudinal and transverse directions of the structures. The maximum pier drifts, bending moments and shear forces demands were analyzed to identify the best isolation properties for reducing the concentration of damage in one or two elements and for improving the structural behavior of irregular bridges. Additionally, the analysis of the seismic response of the bridges supported on traditional neoprene bearings was carried out. 相似文献
19.
Abdoul R. Ghotbi 《地震工程与工程振动(英文版)》2014,13(3):357-373
The seismic behavior of skewed bridges has not been well studied compared to straight bridges. Skewed bridges have shown extensive damage, especially due to deck rotation, shear keys failure, abutment unseating and columnbent drift. This research, therefore, aims to study the behavior of skewed and straight highway overpass bridges both with and without taking into account the effects of Soil-Structure Interaction(SSI) due to near-fault ground motions. Due to several sources of uncertainty associated with the ground motions, soil and structure, a probabilistic approach is needed. Thus, a probabilistic methodology similar to the one developed by the Pacific Earthquake Engineering Research Center(PEER) has been utilized to assess the probability of damage due to various levels of shaking using appropriate intensity measures with minimum dispersions. The probabilistic analyses were performed for various bridge confi gurations and site conditions, including sand ranging from loose to dense and clay ranging from soft to stiff, in order to evaluate the effects. The results proved a considerable susceptibility of skewed bridges to deck rotation and shear keys displacement. It was also found that SSI had a decreasing effect on the damage probability for various demands compared to the fixed-base model without including SSI. However, deck rotation for all types of the soil and also abutment unseating for very loose sand and soft clay showed an increase in damage probability compared to the fixed-base model. The damage probability for various demands has also been found to decrease with an increase of soil strength for both sandy and clayey sites. With respect to the variations in the skew angle, an increase in skew angle has had an increasing effect on the amplitude of the seismic response for various demands. Deck rotation has been very sensitive to the increase in the skew angle; therefore, as the skew angle increased, the deck rotation responded accordingly. Furthermore, abutment unseating showed an increasing trend due to an increase in skew angle for both fixed-base and SSI models. 相似文献