共查询到20条相似文献，搜索用时 46 毫秒
1.
A multi‐azimuth seismic refraction study for a horizontal transverse isotropic medium: physical modelling results 
下载免费PDF全文
下载免费PDF全文 To investigate the characteristics of the anisotropic stratum, a multi‐azimuth seismic refraction technique is proposed in this study since the travel time anomaly of the refraction wave induced by this anisotropic stratum will be large for a far offset receiver. To simplify the problem, a two‐layer (isotropy–horizontal transverse isotropy) model is considered. A new travel time equation of the refracted P‐wave propagation in this two‐layer model is derived, which is the function of the phase and group velocities of the horizontal transverse isotropic stratum. In addition, the measured refraction wave velocity in the physical model experiment is the group velocity. The isotropic intercept time equation of a refraction wave can be directly used to estimate the thickness of the top (isotropic) layer of the two‐layer model because the contrast between the phase and group velocities of the horizontal transverse isotropic medium is seldom greater than 10% in the Earth. If the contrast between the phase and group velocities of an anisotropic medium is small, the approximated travel time equation of a refraction wave is obtained. This equation is only dependent on the group velocity of the horizontal transverse isotropic stratum. The elastic constants A11, A13, and A33 and the Thomsen anisotropic parameter ε of the horizontal transverse isotropic stratum can be estimated using this multi‐azimuth seismic refraction technique. Furthermore, under a condition of weak anisotropy, the Thomsen anisotropic parameter δ of the horizontal transverse isotropic stratum can be estimated by this technique as well. 相似文献
2.
The coupling ray theory is usually applied to anisotropic common reference rays, but it is more accurate if it is applied to reference rays which are closer to the actual wave paths. If we know that a medium is close to uniaxial (transversely isotropic), it may be advantageous to trace reference rays which resemble the SH–wave and SV–wave rays. This paper is devoted to defining and tracing these SH and SV reference rays of elastic S waves in a heterogeneous generally anisotropic medium which is approximately uniaxial (approximately transversely isotropic), and to the corresponding equations of geodesic deviation (dynamic ray tracing). All presented equations are simultaneously applicable to ordinary and extraordinary reference rays of electromagnetic waves in a generally bianisotropic medium which is approximately uniaxially anisotropic. The improvement of the coupling–ray–theory seismograms calculated along the proposed SH and SV reference rays, compared to the coupling–ray–theory seismograms calculated along the anisotropic common reference rays, has already been numerically demonstrated by the authors in four approximately uniaxial velocity models. 相似文献
3.
V.B. Piip 《Geophysical Prospecting》2001,49(4):461-482
A method using simple inversion of refraction traveltimes for the determination of 2D velocity and interface structure is presented. The method is applicable to data obtained from engineering seismics and from deep seismic investigations. The advantage of simple inversion, as opposed to ray‐tracing methods, is that it enables direct calculation of a 2D velocity distribution, including information about interfaces, thus eliminating the calculation of seismic rays at every step of the iteration process. The inversion method is based on a local approximation of the real velocity cross‐section by homogeneous functions of two coordinates. Homogeneous functions are very useful for the approximation of real geological media. Homogeneous velocity functions can include straight‐line seismic boundaries. The contour lines of homogeneous functions are arbitrary curves that are similar to one another. The traveltime curves recorded at the surface of media with homogeneous velocity functions are also similar to one another. This is true for both refraction and reflection traveltime curves. For two reverse traveltime curves, non‐linear transformations exist which continuously convert the direct traveltime curve to the reverse one and vice versa. This fact has enabled us to develop an automatic procedure for the identification of waves refracted at different seismic boundaries using reverse traveltime curves. Homogeneous functions of two coordinates can describe media where the velocity depends significantly on two coordinates. However, the rays and the traveltime fields corresponding to these velocity functions can be transformed to those for media where the velocity depends on one coordinate. The 2D inverse kinematic problem, i.e. the computation of an approximate homogeneous velocity function using the data from two reverse traveltime curves of the refracted first arrival, is thus resolved. Since the solution algorithm is stable, in the case of complex shooting geometry, the common‐velocity cross‐section can be constructed by applying a local approximation. This method enables the reconstruction of practically any arbitrary velocity function of two coordinates. The computer program, known as godograf , which is based on this theory, is a universal program for the interpretation of any system of refraction traveltime curves for any refraction method for both shallow and deep seismic studies of crust and mantle. Examples using synthetic data demonstrate the accuracy of the algorithm and its sensitivity to realistic noise levels. Inversions of the refraction traveltimes from the Salair ore deposit, the Moscow region and the Kamchatka volcano seismic profiles illustrate the methodology, practical considerations and capability of seismic imaging with the inversion method. 相似文献
4.
Paraxial ray methods have found broad applications in the seismic ray method and in numerical modelling and interpretation
of high-frequency seismic wave fields propagating in inhomogeneous, isotropic or anisotropic structures. The basic procedure
in paraxial ray methods consists in dynamic ray tracing. We derive the initial conditions for dynamic ray equations in Cartesian
coordinates, for rays initiated at three types of initial manifolds given in a three-dimensional medium: 1) curved surfaces
(surface source), 2) isolated points (point source), and 3) curved, planar and non-planar lines (line source). These initial
conditions are very general, valid for homogeneous or inhomogeneous, isotropic or anisotropic media, and for both a constant
and a variable initial travel time along the initial manifold. The results presented in the paper considerably extend the
possible applications of the paraxial ray method. 相似文献
5.
Constraining the anisotropy structure of the crust by joint inversion of seismic reflection travel times and wave polarizations 总被引：2，自引：0，他引：2
In the context of wide-angle seismic profiling, the determination of the physical properties of the Earth crust, such as the
elastic layer depth and seismic velocity, is often performed by inversion of P- and/or S-phases propagation data supplying
the geometry of the medium (reflector depths) or any other structural parameter (P- or S-wave velocity, density...). Moreover,
the inversion for velocity structure and interfaces is commonly performed using only seismic reflection travel times and/or
crustal phase amplitudes in isotropic media. But it is very important to utilize more available information to constrain the
non-uniqueness of the solution. In this paper, we present a simultaneous inversion method of seismic reflection travel times
and polarizations data of transient elastic waves in stratified media to reconstruct not only layer depth and vertical P-wave
velocity but also the anisotropy feature of the crust based on the estimation of the Thomsen’s parameters. We carry out
a checking with synthetic data, comparing the inversion results obtained by anisotropic travel-time inversion to the results
derived by joint inversion of seismic reflection travel times and polarizations data. The comparison proves that the first
procedure leads to biased anisotropic models, while the second one fits nearly the real model. This makes the joint inversion
method feasible. Finally, we investigate the geometry, P-wave velocity structure and anisotropy of the crust beneath Southeastern
China by applying the proposed inversion method to previously acquired wide-angle seismic data. In this case, the anisotropy
signature provides clear evidence that the Jiangshan-Shaoxing fault is the natural boundary between the Yangtze and Cathaysia
blocks. 相似文献
6.
L. Klimeš 《Studia Geophysica et Geodaetica》2006,50(3):431-447
Whereas the ray-centred coordinates for isotropic media by Popov and Pšenčík are uniquely defined by the selection of the
basis vectors at one point along the ray, there is considerable freedom in selecting the ray-centred coordinates for anisotropic
media. We describe the properties common to all ray-centred coordinate systems for anisotropic media and general conditions,
which may be imposed on the basis vectors. We then discuss six different particular choices of ray-centred coordinates in
an anisotropic medium. This overview may be useful in choosing the ray-centred coordinates best suited for a particular application.
The equations are derived for a general homogeneous Hamiltonian of an arbitrary degree and are thus applicable both to the
anisotropic-ray-theory rays and anisotropic common S-wave rays. 相似文献
7.
A Fast Sweeping Scheme for Calculating P Wave First-Arrival Travel Times in Transversely Isotropic Media with an Irregular Surface 总被引：2，自引：0，他引：2
Seismic wave propagation shows anisotropic characteristics in many sedimentary rocks. Modern seismic exploration in mountainous areas makes it important to calculate P wave travel times in anisotropic media with irregular surfaces. The challenges in this context are mainly from two aspects. First is how to tackle the irregular surface in a Cartesian coordinate system, and the other lies in solving the anisotropic eikonal equation. Since for anisotropic media the ray (group) velocity direction is not the same as the direction of the travel-time gradient, the travel-time gradient no longer serves as an indicator of the group velocity direction in extrapolating the travel-time field. Recently, a topography-dependent eikonal equation formulated in a curvilinear coordinate system has been established, which is effective for calculating first-arrival travel times in an isotropic model with an irregular surface. Here, we extend the above equation from isotropy to transverse isotropy (TI) by formulating a topography-dependent eikonal equation in TI media in the curvilinear coordinate system, and then use a fast sweeping scheme to solve the topography-dependent anisotropic eikonal equation in the curvilinear coordinate system. Numerical experiments demonstrate the feasibility and accuracy of the scheme in calculating P wave travel times in TI models with an irregular surface. 相似文献
8.
研究与实践表明,对于长偏移距、宽方位地震数据,忽略各向异性会明显降低成像质量,影响储层预测与描述的精度.针对典型的横向各向同性(TI)介质,本文面向深度域构造成像与偏移速度分析的需要,研究基于射线理论的局部角度域叠前深度偏移成像方法.它除了像传统Kirchhoff叠前深度偏移那样输出成像剖面和炮检距域的共成像点道集,还遵循地震波在成像点处的局部方向特征、基于扩展的脉冲响应叠加原理获得入射角度域和照明角度域的成像结果.为了方便快捷地实现TI介质射线走时与局部角度信息的计算,文中讨论和对比了两种改进的射线追踪方法:一种采用从经典各向异性介质射线方程演变而来的由相速度表征的简便形式;另一种采用由对称轴垂直的TI(即VTI)介质声学近似qP波波动方程推导出来的射线方程.文中通过坐标旋转将其扩展到了对称轴倾斜的TI(即TTI)介质.国际上通用的理论模型合成数据偏移试验表明,本文方法既适用于复杂构造成像,又可为TI介质深度域偏移速度分析与模型建立提供高效的偏移引擎. 相似文献
9.
在地震波正反演研究中,考虑起伏地表和地震各向异性具有非常重要的理论意义和实际应用价值.本文在前人研究的基础上,将最短路径追踪算法引入到起伏地表各向异性介质模型的地震波走时计算中.模型剖分时,整体模型划分成正方形单元,起伏边界附近以不规则网格逼近,进而采用非规则节点布置实现非规则网格处的最短路径计算.追踪计算中采用Sena群速度近似公式,得到各向异性地震波的走时,实现了复杂地表情况下各向异性介质模型中地震波的射线追踪.理论模型计算结果显示,本文方法能够可靠地应用于复杂各向异性介质模型,具有较高的计算精度. 相似文献
10.
N. V. Petersen 《Pure and Applied Geophysics》1990,132(1-2):417-437
Scattering at random inhomogeneities in a gradient medium results in systematic deviations of the rays and travel times of refracted body waves from those corresponding to the deterministic velocity component. The character of the difference depends on the parameters of the deterministic and random velocity component. However, at great distances to the source, independently of the velocity parameters (weakly or strongly inhomogeneous medium), the most probable depth of the ray turning point is smaller than that corresponding to the deterministic velocity component, the most probable travel times also being lower. The relative uncertainty in the deterministic velocity component, derived from the mean travel times using methods developed for laterally homogeneous media (for instance, the Herglotz-Wiechert method), is systematic in character, but does not exceed the contrast of velocity inhomogeneities by magnitude. The gradient of the deterministic velocity component has a significant effect on the travel-time fluctuations. The variance at great distances to the source is mainly controlled by shallow inhomogeneities. The travel-time flucutations are studied only for weakly inhomogeneous media. 相似文献
11.
Amir Abbas Babasafari Deva Prasad Ghosh Ahmed Mohammed Ahmed Salim Masoumeh Kordi 《Geophysical Prospecting》2020,68(8):2471-2493
Analysis of amplitude variation with offset is an essential step for reservoir characterization. For an accurate reservoir characterization, the amplitude obtained with an isotropic assumption of the reservoir must be corrected for the anisotropic effects. The objective is seismic anisotropic amplitude correction in an effective medium, and, to this end, values and signs of anisotropic parameter differences (Δδ and Δε) across the reflection interfaces are needed. These parameters can be identified by seismic and well log data. A new technique for anisotropic amplitude correction was developed to modify amplitude changes in seismic data in transversely isotropic media with a vertical axis of symmetry. The results show that characteristics of pre-stack seismic data, that is, amplitude variation with offset gradient, can be potentially related to the sign of anisotropic parameter differences (Δδ and Δε) between two layers of the reflection boundary. The proposed methodology is designed to attain a proper fit between modelled and observed amplitude variation with offset responses, after anisotropic correction, for all possible lithofacies at the reservoir boundary. We first estimate anisotropic parameters, that is, δ and ε, away from the wells through Backus averaging of elastic properties resulted from the first pass of isotropic pre-stack seismic inversion, on input data with no amplitude correction. Next, we estimate the anisotropic parameter differences at reflection interfaces (values and signs of Δδ and Δε). We then generate seismic angle gather data after anisotropic amplitude correction using Rüger's equation for the P-P reflection coefficient. The second pass of isotropic pre-stack seismic inversion is then performed on the amplitude-corrected data, and elastic properties are estimated. Final outcome demonstrates how introduced methodology helps to reduce the uncertainty of elastic property prediction. Pre-stack seismic inversion on amplitude-corrected seismic data results in more accurate elastic property prediction than what can be obtained from non-corrected data. Moreover, a new anisotropy attribute (ν) is presented for improvement of lithology identification. 相似文献
12.
The horizontal transversely isotropic model, with arbitrary symmetry axis orientation, is the simplest effective representative that explains the azimuthal behaviour of seismic data. Estimating the anisotropy parameters of this model is important in reservoir characterisation, specifically in terms of fracture delineation. We propose a travel‐time‐based approach to estimate the anellipticity parameter η and the symmetry axis azimuth ? of a horizontal transversely isotropic medium, given an inhomogeneous elliptic background model (which might be obtained from velocity analysis and well velocities). This is accomplished through a Taylor's series expansion of the travel‐time solution (of the eikonal equation) as a function of parameter η and azimuth angle ?. The accuracy of the travel time expansion is enhanced by the use of Shanks transform. This results in an accurate approximation of the solution of the non‐linear eikonal equation and provides a mechanism to scan simultaneously for the best fitting effective parameters η and ?, without the need for repetitive modelling of travel times. The analysis of the travel time sensitivity to parameters η and ? reveals that travel times are more sensitive to η than to the symmetry axis azimuth ?. Thus, η is better constrained from travel times than the azimuth. Moreover, the two‐parameter scan in the homogeneous case shows that errors in the background model affect the estimation of η and ? differently. While a gradual increase in errors in the background model leads to increasing errors in η, inaccuracies in ?, on the other hand, depend on the background model errors. We also propose a layer‐stripping method valid for a stack of arbitrary oriented symmetry axis horizontal transversely isotropic layers to convert the effective parameters to the interval layer values. 相似文献
13.
The behaviour of the actual polarization of an electromagnetic wave or elastic S–wave is described by the coupling ray theory, which represents the generalization of both the zero–order isotropic and anisotropic ray theories and provides continuous transition between them. The coupling ray theory is usually applied to anisotropic common reference rays, but it is more accurate if it is applied to reference rays which are closer to the actual wave paths. In a generally anisotropic or bianisotropic medium, the actual wave paths may be approximated by the anisotropic–ray–theory rays if these rays behave reasonably. In an approximately uniaxial (approximately transversely isotropic) anisotropic medium, we can define and trace the SH (ordinary) and SV (extraordinary) reference rays, and use them as reference rays for the prevailing–frequency approximation of the coupling ray theory. In both cases, i.e. for the anisotropic–ray–theory rays or the SH and SV reference rays, we have two sets of reference rays. We thus obtain two arrivals along each reference ray of the first set and have to select the correct one. Analogously, we obtain two arrivals along each reference ray of the second set and have to select the correct one. In this paper, we suggest the way of selecting the correct arrivals. We then demonstrate the accuracy of the resulting prevailing–frequency approximation of the coupling ray theory using elastic S waves along the SH and SV reference rays in four different approximately uniaxial (approximately transversely isotropic) velocity models. 相似文献
14.
The common ray approximation considerably simplifies the numerical algorithm of the coupling ray theory for S waves, but may introduce errors in travel times due to the perturbation from the common reference ray. These travel-time errors can deteriorate the coupling-ray-theory solution at high frequencies. It is thus of principal importance for numerical applications to estimate the errors due to the common ray approximation.We derive the equations for estimating the travel-time errors due to the isotropic and anisotropic common ray approximations of the coupling ray theory. These equations represent the main result of the paper. The derivation is based on the general equations for the second-order perturbations of travel time. The accuracy of the anisotropic common ray approximation can be studied along the isotropic common rays, without tracing the anisotropic common rays.The derived equations are numerically tested in three 1-D models of differing degree of anisotropy. The first-order and second-order perturbation expansions of travel time from the isotropic common rays to anisotropic-ray-theory rays are compared with the anisotropic-ray-theory travel times. The errors due to the isotropic common ray approximation and due to the anisotropic common ray approximation are estimated. In the numerical example, the errors of the anisotropic common ray approximation are considerably smaller than the errors of the isotropic common ray approximation.The effect of the isotropic common ray approximation on the coupling-ray-theory synthetic seismograms is demonstrated graphically. For comparison, the effects of the quasi-isotropic projection of the Green tensor, of the quasi-isotropic approximation of the Christoffel matrix, and of the quasi-isotropic perturbation of travel times on the coupling-ray-theory synthetic seismograms are also shown. The projection of the travel-time errors on the relative errors of the time-harmonic Green tensor is briefly presented. 相似文献
15.
16.
THE APPLICATION OF PML BOUNDARY CODITIONS IN THE SIMULATION OF SEISMIC WAVE BY THE HIGH-ORDER STAGGERED-GRID FINITE DIFFERENCES AT THE TRANSVERSELY ISOTROPIC MEDIA 下载免费PDF全文
下载免费PDF全文 In the realm of the numerical simulation, finite difference method and finite element method are more intuitive and effective than other simulation methods. In the process of simulating seismic wave propagation, the finite differences method is widely used because of its high computational efficiency and the advantage of the algorithm is more efficient. With the demand of precision, more and more researchers have proposed more effective methods of finite differences, such as the high-order staggered-grid finite differences method, which can restore the actual process of wave propagation on the premise of ensuring accuracy and improving the efficiency of operation. In the past numerical simulation of seismic wave field, different models of isotropic medium are mostly used, but it is difficult to reflect the true layer situation. With the research demand of natural seismology and seismic exploration, the research on anisotropic media is more and more extensive. Transversely isotropic(TI)media can well simulate the seismic wave propagation in the formation medium, such as gas-bearing sandstone, mudstone, shale et al., the character of TI media is reflected by introducing the Thomsen parameters to reflect its weak anisotropy of vertical direction by using Thomson parameter. Therefore, studying the process of seismic wave propagation in TI media can restore the true information of the formation to the greatest extent, and provide a more reliable simulation basis for the numerical simulation of seismic wave propagation. In the geodynamic simulation and the numerical simulation of the seismic wave field, under the limited influence of the calculation area, if no boundary conditions are added, a strong artificial boundary reflection will be generated, which greatly reduces the validity of the simulation. In order to minimize the influence of model boundaries on the reflection of seismic waves, it is often necessary to introduce absorbing boundary conditions. At present, there are three types of absorption boundary conditions: one-way wave absorption boundary, attenuation absorption boundary, and perfectly matched layer(PML)absorption boundary. In terms of numerical simulation of seismic waves, the boundary absorption effect of PML is stronger than the first two, which is currently the most commonly used method, and it also represents the cutting-edge development direction of absorption boundary technology. The perfectly matched layer absorbing boundary is effectively applied to eliminating the reflective waves from model boundaries, but for transversely isotropic medium, the effect of the absorbing is not very well. For this reason, the elastic dynamic wave equations in transversely isotropic media are derived, and we describe a second-order accurate time, tenth-order accurate space, formulation of the Madariaga-Virieux staggered-grid finite difference methods with the perfectly matched layer(PML)are given. In addition, we have established vertical transversely isotropic(VTI)media and arbitrary inclined tilted transversely isotropic(TTI)media models, using a uniform half-space velocity model and a two-layer velocity model, respectively. By combining the actual geoscience background, we set the corresponding parameters and simulation conditions in order to make our model more research-oriented. When setting model parameters, different PML thickness, incident angle, source frequency and velocity layer models were transformed to verify the inhibition of boundary reflection effect by PML absorption boundary layer. The implementations of this simulation show that the formula is correct and for the transversely isotropic(TI)media of any angular symmetry axis, when the thickness of the PML layer reaches a certain value, the seismic wave reflection effect generated by the artificial boundary can be well suppressed, and the absorption effect of PML is not subject to changes in incident angle and wave frequency. Therefore, the results of our study indicate that our research method can be used to simulate the propagation process of seismic waves in the transversely isotropic(TI)media without being affected by the reflected waves at the model boundary to restore the actual formation information and more valuable geological research. 相似文献
17.
在克希霍夫叠前时间偏移处理中,地震波走时的计算方法是决定大偏移距地震资料成像品质的重要因素.在常规的三维转换波各向异性叠前时间偏移公式中,走时的计算是基于等效单层各向异性介质的非双曲线方法.用这种方法处理的成像道集,在偏移/深度比超过一定阈值后,成像道集中的反射同相轴将出现过偏现象,这种偏移不平的同相轴将影响偏移叠加的最佳响应,使得偏移成像波组呈低频化特征,最终降低三维转换波偏移成像质量.我们采用层状介质的走时计算方法代替常规算法,并且利用了常规方法的转换波各向异性偏移速度模型.基于层状介质的算法能够提高大偏移距转换波走时计算精度,克服中浅地层大偏移距远道成像道集中反射同相轴逐渐上翘的问题.两个地区的三维转换波资料处理结果证实,基于层状各向异性介质的转换波克希霍夫叠前时间偏移方法,明显改善了反射成像剖面的连续性和分辨率,提高成像剖面构造的可解释性. 相似文献
18.
Tariq Alkhalifah 《Geophysical Prospecting》2004,52(1):39-48
The azimuth moveout (AMO) operator in homogeneous transversely isotropic media with a vertical symmetry axis (VTI), as in isotropic media, has an overall skewed saddle shape. However, the AMO operator in anisotropic media is complicated; it includes, among other things, triplications at low angles. Even in weaker anisotropies, with the anisotropy parameter η= 0.1 (10% anisotropy), the AMO operator is considerably different from the isotropic operator, although free of triplications. The structure of the operator in VTI media (positive η) is stretched (has a wider aperture) compared with operators in isotropic media, with the amount of stretch being dependent on the strength of anisotropy. If the medium is both vertically inhomogeneous, i.e. the vertical velocity is a function of depth (v(z)), and anisotropic, which is a common combination in practical problems, the shape of the operator again differs from that for isotropic media. However, the difference in the AMO operator between the homogeneous and the v(z) cases, even for anisotropic media, is small. Stated simply, anisotropy influences the shape and aperture of the AMO operator far more than vertical inhomogeneity does. 相似文献
19.
20.
Perturbation methods are common tools for describing wave propagation in weakly anisotropic media. The anisotropic medium is replaced by an average isotropic medium where wave propagation can be treated analytically and the correction for the effect of anisotropy is computed by perturbation techniques. This works well for anisotropies of up to 10%. Some materials (e.g. shales), however, can exhibit a much stronger anisotropy. In this case a background is required which still can be treated analytically but is applicable to stronger P-wave anisotropy. We present an averaging technique to compute a best-fitting ellipsoidal medium to an arbitrary anisotropic medium. Ellipsoidal media are sufficiently simple for analytical expressions to be available for many applications and allow consideration of strong P-wave anisotropy. The averaging of the arbitrary anisotropic medium can be carried out globally (i.e. for the whole sphere) or sectorially (e.g. for seismic waves propagating predominantly in the vertical direction). We derive linear relationships for the coefficients of the ellipsoid which depend on the elastic coefficients of the anisotropic medium. We also provide specifications for best-fitting elliptical and best-fitting isotropic media. Numerical examples for different rocks demonstrate the improved approximation of the anisotropic model obtained using the formulae derived, compared with the conventionally used average isotropic medium. 相似文献