共查询到20条相似文献，搜索用时 46 毫秒
1.
考虑桩土作用独桩海洋平台横向振动特性研究 总被引：5，自引：0，他引：5
采用动Winkler弹性地基梁模型模拟桩土问动力相互作用，并考虑了流体与桩问相互作用，通过组合成层土中、水中桩单元的刚度阵，推得了独桩海洋平台连续系统横向振动的动刚度阵及在波浪力作用下平台甲板处的频率响应函数，进而求得了在确定性波浪力及随机波浪力作用下桩身任意点的位移响应。最后，通过算例研究和分析了在随机波浪力作用下成层土参数、甲板上重量及冲刷淘深等因素对平台振动响应的影响。 相似文献
2.
3.
本文主要对流体-重力式单腿平台结构-土相互作用体系在地震荷载作用下的动力响应问题进行了研究。分析了考虑土-结构相互作用及不考虑相互作用效应对体系动力响应的影响,同时研究了沉箱基础半径和海水深度变化对体系动力响应的影响,并结合一个简单实例进行了数值分析。 相似文献
4.
采用修正的p-y曲线方法，分析了桩基础振动过程中桩土之间由于土体塑性变形导致的桩土脱开现象，给出了计算桩土脱开现象的数值模拟方法，并据此分析计算了中国渤海湾JZ20－2MUQ平台的桩基础动力特性，得到了桩基础振动过程中桩土脱开的区域，分析了桩土之间的脱开对桩基础动力响应的影响等问题。 相似文献
5.
为考虑桩土相互作用的高桩码头体系等效阻尼比,将地震作用下高桩码头的滞回耗能定义为各桩塑性铰耗能和桩-土相互作用耗能之和,桩-土相互作用耗能根据p-y曲线和Masing准则定义的滞回环确定,码头结构的塑性铰总耗能为各桩塑性铰耗能的总和,按照正弦激励下一个振动循环内高桩码头体系与相应单自由度体系粘滞耗能相等的原则,推导得到了高桩码头体系等效阻尼比计算公式,并对两个高桩码头进行了Pushover分析。分析表明,土体耗能对高桩码头体系阻尼贡献较大,根据码头各桩塑性铰出现顺序和转动情况计算码头的等效阻尼比更符合实际情况。 相似文献
6.
考虑群桩效应的海洋平台桩—土—结构共同工作研究 总被引：1，自引：0，他引：1
考虑群桩效应的近海导管架平台的桩、土结构共同工作研究是一个很复杂的课题，要考虑很多因素。在平台结构的概念设计或初步设计中则可采用一些近似方法。本文根据目前国内外对群桩研究的成果，依据文克尔相互作用模型，提出了一个较方便实用的群桩效应计算方法，并建立了考虑群桩效应的桩—土—结构共同工作的计算模型，通过编制计算机程序得到实现，最后根据算例分析得到有关结论 相似文献
7.
8.
9.
极端荷载作用下海洋导管架平台体系可靠度分析 总被引：4，自引：1，他引：4
采用非线性倒塌分析方法，考虑桩－土－结构的非线性相互作用，研究了导管架平台在极端荷载作用下承载能力的计算模型，分析了平台结构体系在极端荷载作用下的全倒塌全过程，在此基础上，结合蒙特卡洛法，提出了海洋导管架平台结构的体系可靠度计算方法。最后对工程实例－涠11－4C海洋平台的结构进行了体系可靠性分析，并对比分析了不同的荷载效应计算公式对计算经的影响，研究表明计算经满足工程设计要求，便于工程应用。 相似文献
10.
本文应用地震随机响应分析理论,研究了海洋桩基平台地震随机响应分析方法。该分析方法将强地面运动视为三向平稳白噪声随机过程,同时考虑了桩土相互作用和水与结构的耦联作用。应用该方法对一典型平台进行了计算,并与现行的响应谱法进行了比较,从而验证了本文所述方法的适用性。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
20.