共查询到20条相似文献，搜索用时 53 毫秒
1.
姜伏伟 《水文地质工程地质》2017,(2):90-95
本文分析了武宣土洞发育的地质背景、水动力诱发土洞的过程,在理想条件下,建立了土体渗透破坏形成土洞的管道流机理模型,根据管道流理论,分析得出土洞发育水动力条件表达式。通过自行设计的管道流测试仪装置,进行管道流模拟试验,计算得出研究区土洞发育的临界切应力为21.20 Pa。运用电子扫描电镜技术,测试研究区孔隙等效直径为31.6 nm,计算得出研究区土洞发育的临界水流为0.530 cm/min。对比临界水流和现场监测的实际地下水流,评价土洞发育的可能性。结果表明,目前情况下,地下水流未达到临界值,不具备引起黏土流失形成土洞的水动力条件。 相似文献
2.
3.
Collapse hazard zonation of qanats in greater Tehran area 总被引：2，自引：0，他引：2
Mohammad H. T. Rayhani M. Hesham El Naggar 《Geotechnical and Geological Engineering》2007,25(3):327-338
Abstarct Several cases of subsidence occurred in greater Tehran resulting from collapse of walls of underground water channel system
known locally as qanat. Many mechanisms contribute to the qanat collapse, which add to the complexity of the problem. The
present research focuses on identifying the main factors that influence qanat collapse and the parameters that should be considered
in modeling their behavior. Some of the important factors that influence the stability and performance of qanats and considered
in the analysis presented here include: qanat geometrical characteristics; loading due to surface structures; underground
water level and geotechnical properties of the soil. A suitable model was chosen and deformational behavior of qanat walls
was simulated. The stability of qanats was evaluated considering both elastic and elasto-plastic soil models. It was found
that qanats in north and northeastern parts of Tehran have high strength and qanats in south and southwestern parts have low
strength. A GIS-based qanat collapse hazard zonation map was prepared. It was found that the hazard of collapse increases
for shallow qanats with any structural loads imposed at the ground surface. As expected, this hazard is much higher for qanats
situated in weak soils. Furthermore, the hazard of collapse is much higher for qanats with larger diameter. 相似文献
4.
Geotechnical engineering practice for collapsible soils 总被引：3，自引：0，他引：3
Sandra L. Houston William N. Houston Claudia E. Zapata Chris Lawrence 《Geotechnical and Geological Engineering》2001,19(3-4):333-355
Conditions in arid and semi-arid climates favor the formation of the most problematic collapsible soils. The mechanisms that account for almost all naturally occurring collapsible soil deposits are debris flows, rapid alluvial depositions, and wind-blown deposits (loess). Collapsible soils are moisture sensitive in that increase in moisture content is the primary triggering mechanism for the volume reduction of these soils. One result of urbanization in arid regions is an increase in soil moisture content. Therefore, the impact of development-induced changes in surface and groundwater regimes on the engineering performance of moisture sensitive arid soils, including collapsible soils, becomes a critical issue for continued sustainable population expansion into arid regions.In practicing collapsible soils engineering, geotechnical engineers are faced with (1) identification and characterization of collapsible soil sites, (2) estimation of the extent and degree of wetting, (3) estimation of collapse strains and collapse settlements, and (4) selection of design/mitigation alternatives. Estimation of the extent and degree of wetting is the most difficult of these tasks, followed by selection of the best mitigation alternative. 相似文献
5.
The climatic zones where residual soils occur are often characterized by alternate wet and dry seasons. Laboratory studies
of earlier workers have established that the alternate wetting and drying process affects the swell-shrink potentials, water
content, void ratio and particle cementation of expansive soils. The influence of cyclic wetting and drying on the collapse
behaviour of residual soils has not been examined. This paper examines the influence of alternate wetting and drying on the
collapse behaviour of compacted residual soil specimens from Bangalore District. Results of such a study are useful in anticipating
changes in collapse behaviour of compacted residual soil fills. Experimental results indicated that the cyclic wetting and
drying process increased the degree of expansiveness of the residual soils and reduced their collapse tendency. Changes in
the swell/collapse behaviour of compacted residual soil specimens from wetting drying effects are attributed to reduction
in water content, void ratio and possible growth of cementation bonds. 相似文献
6.
Deformation and strength characteristics of the soil of Sana'a, the Yemen Arab Republic, were investigated. Undisturbed soil samples were collected fro used in consolidation, collapse and strength tests. The classical and critical state compressibility parameters were determined using a one-dimensional collapsing potential of the investigated soil was determined by using both qualitative and quantitative analysis. Consolidated undrained triaxial tests different types of samples: saturated samples and samples at natural moisture content. The stress history of the fine soils are in the range of normal except for the stiff fissured lean clay which exhibited a relatively high overconsolidated stress history. The loess formations exhibited a moderate to under wetting and loading. The investigated soils are characterized by having high shear strength when they have low moisture content and a drastic dec content increases. 相似文献
7.
Arid saline soils are well-distributed over the globe, with a variety of nomenclature. Along the seaboard of the Arabian Gulf, these soils exist widely and are known as “sabkhas”. Despite the cemented and saline characteristics of the sabkha matrix, a recent investigation indicated that flooding the saline sabkha with distilled water in the conventional oedometer apparatus was incapable of producing a sudden reduction in volume and/or a significant collapse. This study proposes a modification to the conventional oedometer on undisturbed sabkha specimens to consolidating specimens under a constant head. Tests were, therefore, conducted on undisturbed sabkha specimens to assess their compressibility and collapse potential whereby percolation of water was commenced under two pressures to evaluate the role of sustained pressure on the collapse mechanisms.
Despite the low compressibility of sabkhas, results of these tests indicated that these arid, saline soils possess a high collapse potential attributable primarily to dissolution of sodium chlorides, leaching of calcium ions and soil grain adjustment. The collapse potential increases with an increase in the acting pressure at which percolation of water takes place. In contrast to other typical soils, the collapse of arid, saline soils is not instantaneous but requires sufficient volume of water to percolate in order to enhance the dissolution of the cementing agents. 相似文献
8.
Probabilistic analysis of landslide potential of an inclined uniform soil layer of infinite length: application 总被引：1，自引：0，他引：1
An extended probabilistic model that is a modification of the Chen et al. (2007,) model for evaluating the failure probability
of an inclined soil layer with an infinite length was developed in the present paper, and then applied to evaluate the occurrence
probability of landslide-related debris flow in Tungmen gully located in the eastern Taiwan, which occurred a devastating
debris flow in 1990. The statistical properties of hydrogeological parameters were collected and summarized, and then used
to evaluate the landslide-related debris-flow probabilities at various relative water depths for Tungmen gully by using the
probabilistic model. Under the assumption that the soil is saturated, the soil’s cohesion is negligible and the specific gravity
of the solid particles of soils is a constant, a simplified probabilistic critical slope equation for the stability of an
infinite slope of soils was also developed, and used to estimate the occurrence probability of debris flow. The result shows
that probabilistic landslide analysis for an infinite slope could provide a suitable approximation for the risk analysis of
debris flow mobilization at a given gully. 相似文献
9.
结构性土颗粒间的胶结使试样剪切破坏最终应力比高于相应重塑土,也限制了试样剪切时体积应变的自由发挥。在考虑结构垮塌为主的结构性土统一硬化(UH)模型基础上,将应力空间中静止的临界状态线扩展为动态的移动临界状态线。据此,通过建立新的屈服面方程并修正剪胀方程,将结构性土统一硬化(UH)模型扩展为胶结结构性土统一硬化(UH)模型。相对于原模型,新模型增加了1个模型参数,即初始胶结应力,反映土颗粒之间的初始胶结作用。通过4种结构性土试验数据与模型预测对照表明：所提模型能够较合理地描述结构性土等向压缩、常规三轴排水与不排水剪切等特性。 相似文献
10.
土体应力-应变关系转型问题分析 总被引：14，自引：2，他引：12
通过对土体应力应变试验结果的分析,明确指出了土体普遍存在的应力-应变关系转型现象。提出了按后破坏模量和临界围压两个参数判别土体应力-应变关系转型的方法,对影响土体应力-应变关系转型的因素包括土的类型、围压、初始密度或含水率、排水条件及应力路径等进行了简要分析。最后,对砂土初步提出了一个能反映转型现象的组合应力-应变关系模型的理论框架。 相似文献
11.
Cracks are common in clayey or expansive soils and provide preferential pathways for water infiltration into soils. A field study was conducted to investigate the mechanisms of initiation and development of desiccation cracks on two soils. Based on results of the field study and measurements of soil-water retention curves and soil shrinkage properties in the laboratory, the conditions of crack initiation and the development of crack geometric parameters (i.e., crack porosity, crack aperture, and crack density) with water content or drying time were quantified. The results show that desiccation cracks developed in three stages: initial stage, primary stage, and steady state stage. In the initial stage, few cracks developed with gradually decreasing water content. When the water content reached a critical value for crack initiation, cracks developed quickly and this was the start of the primary stage. The critical suction at crack initiation was calculated using a stress criterion, which is in the range of 5.3–21.3 times the preconsolidation pressure of the soil. As the water content approached the shrinkage limit of the soil, cracks developed slowly and approached a steady state. The cracks were found to be repeatable during three drying–wetting cycles. 相似文献
12.
《Geomechanics and Geoengineering》2013,8(1):28-35
Establishing the soil water retention curve, SWRC or the soil water characteristic curve, SWCC, is very useful for determination of unsaturated properties of soils. However, it has been observed that SWRC of a soil is not unique and depends on various factors such as the initial moisture content, density of soil, method of compaction, soil fabric and the path (drying or wetting) adopted for establishing it. In this context, many techniques and instruments have been employed by earlier researchers for determination of the SWRC of soils. However, these techniques entail weighing of the samples during prolonged testing, manually, and hence yield discrete data points. In this situation, AquaSorp® Isotherm Generator (manufactured by Decagon Devices Inc., USA) has been found to be quite useful for continuous determination of the drying-path SWRC of fine-grained soils. This device has been primarily employed for food products, powders and amorphous materials. Hence, demonstration of the utility and limitations of this device for SWRC determination of fine-grained soils becomes essential. With this in mind, extensive studies were conducted on commercially available soils (Kaolinite and Bentonite) by employing this device. In order to understand the influence of specimen specific parameters on the obtained SWRCs, the molding water content and thickness of the specimens were varied and the results have been evaluated critically. Details of the methodology adopted for these investigations, and the findings of the study are presented in this technical note. Based on a critical comparison of the results obtained from this device with those obtained from the dewpoint potentiameter, WP4®, the utility of this device for continuous determination of drying-path SWRC of the soils has also been demonstrated. 相似文献
13.
Vertical soil arching, commonly known as the “trapdoor mechanism,” is a pervasive phenomenon in various geotechnical applications that can be evaluated through a variety of analytical and numerical approaches, most of which exist due to a variety of proposed arching mechanisms, many of which are focused on either purely frictional or cohesive soils. This study investigates the realized arching mechanisms and associated loads for trapdoors under both active and passive arching conditions in c′-ϕ′ soils through a series of dimensionless charts using both upper and lower bound limit analyses. An associated sensitivity analysis demonstrates that arching loads are highly dependent on collapse mechanism, a function of not only geometry, but soil shear strength, with cohesion affecting the realized mechanism and arching loads. 相似文献
14.
A critical relation for mobilization (failure) of an inclined, uniform soil layer is developed, based on the requirement for
balancing the driving stress and the resistance stress acting on the soil layer. Taking into consideration of the uncertainties
of parameters of the considered soil layer, the equation of the failure probability (Eq. 18) and the equation of the critical slope at various probabilities of failure (Eq. 22) for the soil layer by applying the first-order second-moment method (FOSM) were developed. The failure probabilities at
various mean relative water depths subject to the upper and lower values of the coefficients of variations of parameters and
two inclined angles of the soil layers are also estimated by using the Monte Carlo simulation method (MCSM) as well as by
using FOSM for comparisons. The results obtained by FOSM are in good agreement with that obtained by MCSM, but the former
is more efficient. Given the mean values and the coefficients of variation of related parameters of the soil layer, one can
easily estimate the failure probability and the critical failure slope of the soil layer by applying the equations or graphs
developed in the present study. 相似文献
15.
Discarding known data from cored samples in the reliability analysis of a slope in spatially variable soils is a waste of site investigation effort. The traditional unconditional random field simulation, which neglects these known data, may overestimate the simulation variance of the underlying random fields of the soil properties. This paper attempts to evaluate the reliability of a slope in spatially variable soils while considering the known data at particular locations. Conditional random fields are simulated based on the Kriging method and the Cholesky decomposition technique to match the known data at measured locations. Subset simulation (SS) is then performed to calculate the probability of slope failure. A hypothetical homogeneous cohesion-frictional slope is taken as an example to investigate its reliability conditioned on several virtual samples. Various parametric studies are performed to explore the effect of different layouts of the virtual samples on the factor of safety (FS), the spatial variation of the critical slip surface and the probability of slope failure. The results suggest that whether the conditional random fields can be accurately simulated depends highly on the ratio of the sample distance and the autocorrelation distance. Better simulation results are obtained with smaller ratios. Additionally, compared with unconditional random field simulations, conditional random field simulations can significantly reduce the simulation variance, which leads to a narrower variation range of the FS and its location and a much lower probability of failure. The results also highlight the great significance of the conditional random field simulation at relatively large autocorrelation distances. 相似文献
16.
为了研究干密度、含水率和NaCl含量对遗址土热劣化的影响,采用Hot Disk热常数分析仪对良渚遗址、交河故城遗址和通古斯巴西古城遗址的遗址土重塑样进行了热物理参数的测试,分别确定了遗址土的导热系数、热扩散系数和体积比热随干密度和含水率的变化关系。对通古斯巴西古城遗址重塑样掺入了不同含量的NaCl,研究了含盐量对遗址土重塑样导热系数的影响。结果表明,当含水率与干密度增加时,3种遗址土的导热系数均呈线性增长,热扩散系数和体积比热也随着含水率与干密度的增加而增大;相同条件下3种遗址土的热物理参数存在差异,良渚遗址的较大,交河遗址的较小,通古斯巴西古城的居中总体上与土中SiO2含量成正相关关系。当干密度与含水率一定时, 掺入NaCl增加了遗址土的导热系数。 相似文献
17.
It is well known that soil is inherently anisotropic and its mechanical behavior is significantly influenced by its fabric anisotropy. Hypoplasticity is increasingly being accepted in the constitutive modeling for soils, in which many salient features, such as nonlinear stress-strain relations, dilatancy, and critical state failure, can be described by a single tensorial equation. However, within the framework of hypoplasticity, modeling fabric anisotropy remains challenging, as the fabric and its evolution are often vaguely assumed without a sound basis. This paper presents a hypoplastic constitutive model for granular soils based on the newly developed anisotropic critical state theory, in which the conditions of fabric anisotropy are concurrently satisfied along with the traditional conditions at the critical state. A deviatoric fabric tensor is introduced into the Gudehus-Bauer hypoplastic model, and a scalar-valued anisotropic state variable signifying the interplay between the fabric and the stress state is used to characterize its impact on the dilatancy and strength of the soils. In addition, fabric evolution during shearing can explicitly be addressed. Modifications have also been undertaken to improve the performance of the undrained response of the model. The anisotropic hypoplastic model can simulate experimental tests for sand under various combinations of principle stress direction, intermediate principal stress (or mode of shearing), soil densities, and confining pressures, and the associated drastic effect of different principal stress orientations in reference to the material axes of anisotropy can be well captured. 相似文献
18.
19.
Collapsible soils are problematic by nature. They undergo collapse or sudden settlement or subsidence under a given stress when their water content is increased. Collapse is characterised by collapse potential expressed as ΔH/H x 100, where ΔH is collapse compression. The amount of stress applied and the water content at the time of collapse govern the amount of collapse. In other words, collapse potential depends upon the amount of stress and the water content. Loess and other wind-blown silts are examples of collapsible soils. This paper presents a parametric study on the collapse behaviour of a lateritic soil. Remoulded specimens of a lateritic soil passing through a 425 µm sieve were compacted in 1-D consolidometer or oedometer at a density of 13 kN/m3 for studying collapse under varied initial moisture contents and initial surcharge pressures. Collapse compression of the samples was induced by saturating the specimens with water contents corresponding to 100% degree of saturation. After collapse occurred, the 1-D consolidation tests were continued up to an applied stress of 160 kPa. Collapse behaviour was studied for the applied initial pressures (σi) of 10, 20 and 40 kPa and for the initial water contents (wi) of 5%, 10%, 15% and 20%. Collapse compression and collapse potential decreased with increasing wi for all σi. 相似文献
20.
岩溶塌陷发育机理模式研究 总被引：6，自引：5，他引：1
岩溶塌陷是我国岩溶区常见的地质灾害。目前,关于岩溶塌陷发育机理模式主要以力学分析为主。文章以岩溶塌陷过程为基础,探讨分析岩溶塌陷发育机理模式。依据地下水埋藏条件,土体分为包气带非饱和土体、潜水层饱和土体及承压水层承压性土体。根据“水-+土”相互作用,在包气带、潜水层和承压水层分别建立崩解作用、潜蚀作用和水力裂隙作用三种岩溶塌陷发育机理模式。 相似文献