共查询到20条相似文献，搜索用时 296 毫秒
1.
The cured‐in‐place‐pipe (CIPP) liner technology involves installation of flexible polymeric composite liners coated with thermosetting resin to the inner surfaces of existing buried pipelines. This innovative technology provides an efficient, economic, and environmentally friendly alternative for rehabilitation of structurally compromised underground pipelines without expensive and disruptive excavation. However, the lack of analytical/numerical procedures to quantify the seismic performance of CIPP liner reinforced pipelines remains a barrier to the seismic design and rehabilitation of underground pipelines. This paper first develops an experimentally validated hysteretic model of ductile iron push‐on joints, reinforced with one particular type of CIPP liner under repeated axial loading. A numerical procedure is then proposed to systematically assess the seismic performance and fragility of straight buried pipelines incorporating push‐on joints and subjected to transient ground deformations. The numerical results indicate that CIPP liner‐reinforced pipelines exhibit favorable robust seismic performance with limited joint damage under high‐intensity transient ground deformations. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
2.
基于ABAQUS软件平台,建立穿越断层的管道、有压液体及周围土体的三维有限元模型,分别在静力荷载作用和地震作用下,对不同运动形式断层（走滑断层、正断层、逆断层）中的管道进行模拟,并对管道内有无有压液体进行对比分析。分别得到管道在静力荷载作用下和地震作用下空管道与有压管道的变形特征,将其进行对比分析,得到管道内液体的质量和压力在静力荷载作用及地震荷载作用下对管道的不同影响。结果表明：在静力荷载作用下管道内液体的质量和压力提高了管道的抗变形能力,使管道更安全;而在地震作用下管道内液体的质量和压力削弱了管道的抗变形能力,使管道更容易被破坏。 相似文献
3.
The seismic response analysis of buried pipelines at fault crossings is a complex problem requiring nonlinear 3D soil-structure and large deformation analyses. Such analyses are computationally expensive and the results are hard to evaluate. Therefore, a simple numerical model is needed for engineering and design offices to determine the seismic demand of steel pipes at fault crossings. This paper presents a simplified numerical model for buried steel pipes crossing strike-slip faults and oriented perpendicular to the fault. Two pipes with different diameter to thickness ( D/ t) ratios and steel grades are used in the study. The proposed model permits plastic hinge formations in the pipe due to incrementally applied fault movements, allows determination of the critical length of the pipeline and measure strains developed on the tension and compression sides in the pipe. The model also considers the effect of bending as well as axial strains due to stretching. 相似文献
4.
架空管道由于地震波传递、地震动衰减以及场地不均匀产生各支撑点地震动差异,为了研究这种差异对架空管道地震响应的影响,通过有限元软件ADINA建立架空管道有限元模型,利用MATLAB软件编写具有相干效应的人工地震波,计算分析了多点地震动相干函数法输入、行波输入与一致输入下地震响应。结果表明:①随着视波速的增加管道轴向应变变小,有接近一致激励情况的趋势;②同一相干函数模型,考虑和忽略场地效应,管道轴向应变最大值存在差异;不同相干函数模型,管道轴向应变最大值也存在差异。结论认为,如果场地比较均匀且管段较短,可采用行波法进行地震输入;长柔管道应采用相干法进行地震响应分析,场地不均匀的长柔管道,应同时考虑场地效应。 相似文献
5.
Seismic capacity, including the ultimate load-carrying capacity and ultimate deformation capacity of precast segmental concrete double-column(PSCDC) piers with steel sleeve(SS) connection or grouted corrugated-metal duct(GCMD) connection, has been verified to be similar to those of cast-in-place(CIP) piers by quasi-static tests. However, the lack of knowledge of seismic response characteristics and damage process of PSCDC piers has limited their application in high-intensity seismic areas. Therefore, shake table tests, using variable types and intensities of seismic ground motions, were performed to investigate the seismic behavior of connection joints and to evaluate the seismic performance of PSCDC piers with SS and GCMD connections. Also, a finite element analysis(FEA) model was developed to study the influence of design parameters on the seismic behavior of the piers. The results showed that the main damage in PSCDC piers was caused by the cyclic opening and closing of connection joints. Under high-intensity ground motions, the PSCDC piers had a lower seismic performance than the CIP piers due to a significant decrease of their integrity and stiffness. The seismic performance of PSCDC piers is comparable to CIP piers when using an appropriate initial stress of the prestressing tendons. 相似文献
6.
This paper deals with seismic wave propagation effects on buried segmented pipelines. A finite element model is developed for estimating the axial pipe strain and relative joint displacement of segmented pipelines. The model accounts for the effects of peak ground strain, shear transfer between soil and pipeline, axial stiffness of the pipeline, joint characteristics of the pipeline, and variability of the joint capacity and stiffness. For engineering applications, simplified analytical equations are developed for estimating the maximum pipe strain and relative joint displacement. The finite element and analytical solutions show that the segmented pipeline is relatively flexible with respect to ground deformation induced by seismic waves and deforms together with the ground. The ground strain within each pipe segmental length is shared by the joint displacement and pipe barrel strain. When the maximum ground strain is higher than 0.001, the pipe barrel strain is relatively small and can be ignored. The relative joint displacement of the segmented pipeline is mainly affected by the variability of the joint pullout capacity and accumulates at locally weak joints. 相似文献
7.
Ground-motion Intensity Measures (IMs) are used to quantify the strength of ground motions and evaluate the response of structures. IMs act as a link between seismic demand and seismic hazard analysis and therefore, have a key role in performance-based earthquake engineering. Many studies have been carried out on the determination of suitable IMs in terms of efficiency, sufficiency and scaling robustness. The majority of these investigations focused on ordinary structures such as buildings and bridges, and only a few were about buried pipelines. In the current study, the optimal IMs for predicting the seismic demand of continuous buried steel pipelines under near-field pulse-like ground motion records is investigated. Incremental dynamic analysis is performed using twenty ground motion records. Using the results of the regression analysis, the optimality of 23 potential IMs are studied. It is concluded that specific energy density (SED) followed by \(\sqrt {VSI[{\omega _1}(PGD + RM{S_d})]} \) are the optimal IMs based on efficiency, sufficiency and scaling robustness for seismic response evaluation of buried pipelines under near-field ground motions. 相似文献
8.
地震作用下,活动断层附近的埋地管道易发生强度屈服、局部屈曲或整体失稳等形式的破坏,建立准确、高效的埋地管道在断层作用下的计算模型,对管道的抗震设计和震后安全状态评估具有重要的实用价值。本文采用非线性弹簧模拟远离断层处埋地管道的反应,基于管土之间小变形段管道处于强化阶段,提出一种改进的管土等效分析模型,进一步减小了管土之间大变形段的分析长度,从而提高了有限元分析效率。该模型采用ALA推荐的方法计算管土间的滑动摩擦力,可以考虑土体种类的影响;用Kennedy方法确定管道的计算长度。通过与精确模型比较,验证了管土等效模型的合理性和有效性。 相似文献
9.
This paper aims to provide a guideline for numerical modeling of reinforced concrete (RC) frame elements for the seismic performance assessment of a structure. Several types of numerical models of RC frame elements are available in nonlinear structural analysis packages. Because the numerical models are formulated based on different assumptions and theories, the models' accuracy, computing time, and applicability vary, which poses a great difficulty to practicing engineers and limits their confidence in the analysis results. In this study, the applicability of five representative numerical models of RC frame elements is evaluated through comparison with 320 experimental results available from the Pacific Earthquake Engineering Research column database. The accuracy of a numerical model is evaluated according to its initial stiffness, peak strength, and energy dissipation capacity of the global responses. In addition, a parametric study of a cantilever RC column subjected to earthquake excitation is carried out to systematically evaluate the consequence of the adopted numerical models on the maximum inelastic structural responses. It is found from this study that the accuracy of the numerical models is sensitive to shear force demand–capacity ratio. If a structural period is short and the structure is shear critical, the use of numerical models that can explicitly capture the shear deformation and failure is suggested. If the structural period is long, the selection of a numerical model does not greatly influence the global response of the structure. The paper also presents statistical parameters of each numerical model, which can be used for probabilistic seismic performance assessment. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
10.
The energy dissipation capacity of a structure is a very important index that indicates the structural performance in energy‐based seismic design. This index depends greatly on the structural components that form the whole system. Owing to the wide use of the strong‐column weak‐beam strength hierarchy where steel beams dissipate the majority of earthquake input energy to the structures, it is necessary to evaluate the energy dissipation capacity of the beams. Under cyclic loadings such as seismic effects, the damage of the beams accumulates. Therefore, loading history is known to be the most pivotal factor influencing the deformation capacity and energy dissipation capacity of the beams. Seismic loadings with significantly different characteristics are applied to structural beams during different types of earthquakes and there is no unique appropriate loading protocol that can represent all types of seismic loadings. This paper focuses on the effects of various loading histories on the deformation capacity and energy dissipation capacity of the beams. Cyclic loading tests of steel beams were performed. In addition, some experimental results from published tests were also collected to form a database. This database was used to evaluate the energy dissipation capacity of steel beams suffering from ductile fracture under various loading histories. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
11.
为研究埋地管道在地震激励时管-土相互作用的动力响应问题,研发双向层状剪切连续体模型土箱,建立管G土相互作用有限元分析模型,对横向非一致地震激励下埋地管道地震响应进行数值模拟分析,并与试验结果进行对比.结果表明:数值模拟和振动台试验结果中的管道应变峰值均呈现出沿管道中间大两端小的现象,管道中间应变峰值最小达到两端的1．6倍左右;管道加速度、 土体加速度峰值均随着加载等级的提高而增大,涨幅愈加明显,多峰频率由0~10Hz逐渐向10~ 20Hz频域扩散,管道运动更为自由;土体位移随着加载等级的提高呈现逐级增大的现象,在加载等级增加到0．4g 时位移曲线斜率减小,土体非线性表现明显.数值模拟和振动台试验对比分析的结论表明数值模拟分析的合理性和试验结果的可靠性,为研究横向非一致激励对埋地管道地震响应的影响提供了依据. 相似文献
12.
Earthquake response of underground lifeline engineering is investigated by the method of ultrasonic model experiments in this
paper. From general field conditions, two models of underground lifeline engineering, one for non-uniform field and the other
for uniform field, are designed based on the similarity principle. Besides analysis of seismic phases, a series of analyses
especially on particle vibration are carried out. The results show that:
The shorter the epicentral distance, the greater are the intensity variation and the change rate of intensity variation of
earthquake ground motion, so the more disadvantageous to underground pipelines. In soft covering layer, compressional waves
mainly cause radial flexures deformation, but shear wave result in axial dilation deformation of the pipelines; when the thickness
of the covering layer is smaller (less than seismic wave length), the rhythmic variation of the intensity of earthquake ground
motion is controlled mainly by the wave length of seismic waves in the bedrock. The property of the covering layer has considerable
effect on earthquake ground motion. For different covering layers, their effect on each component of earthquake ground motion
is not the same.
Owing to the effect of wave propagation, the ground is in different states of particle vibration at different times, and there
is considerable difference in phase and intensity of particle vibration between two different covering layers near their junction
line or surface. Because underground lifelines tend to vibrate with the particles of the earth around it, this results in
different deformation of underground pipelines under different conditions. So, it is necessary to take corresponding anti-seismic
countermeasures for pipelines according to their practical situations.
The Chinese version of this paper appeared in the Chinese edition of Acta Seismologica Sinica, 14, 104–110, 1992.
This paper is part of the research supported by Funds of Doctoral Faculty of National Education Committee. 相似文献
13.
Nuclear fuel fabrication and reprocessing facilities have glove boxes that are extensively used as a primary containment for radiological material. These equipment are maintained under negative pressure using ventilation system and possess high degree of leak tightness. Sometimes, they are used as a standalone structure and many a times, interconnected to each other. Normally, they are not anchored to the floor, which raises serious concerns about their seismic performance. To check seismic stability of the glove boxes and evaluate safety margins in design, tri directional fullscale shake table experiments of two interconnected glove boxes had been carried out. Two configurations were compared; in first, both the boxes were connected through flexible linkage (material transfer tunnel) and in second both were rigidly connected via structural members. Objective of experiments was to observe effects of seismic excitation on leak tightness, structural integrity and overall stability of two interconnected glove boxes. Subsequently, nonlinear finite element analysis was carried out to establish and develop analysis methodology. Experimental results were utilized for model benchmarking. Furthermore, a numerical method was developed to determine safe upper bounds on sliding displacements. This paper highlighted critical findings emanated from experimental results and examined their effect on seismic stability. Enhanced seismic stability in case of rigidly connected boxes was observed. Rigid body motions (mainly sliding and low magnitude rocking) dominated the response with very limited effect of elastic motions. Methodology used for modelling and analyzing glove boxes under seismic loading using finite element methods was also presented. 相似文献
14.
A new remediation technique is proposed to mitigate large deformations imposed on buried pipeline systems subject to permanent ground deformation. With this technique, low-density gravel (LDG) with high porosity, such as pumice, is used as backfill in the trench containing the pipe near an area susceptible to PGD. This countermeasure decreases soil resistance, soil-pipe interaction forces and strain on the pipe as the pipeline deformation mechanism changes to a more desirable shape. Expanded polystyrene geofoam has been introduced to decrease the density of the pipeline backfill; however, LDG is more efficient regarding workability during construction, environmental effects, durability, fire safety, and cost-effectiveness. A series of centrifuge model experiments in which the pipelines were subjected to reverse faulting was conducted to evaluate the proposed method. During faulting, the axial and bending strain and pipe deflection were measured. A comparison of the responses of the remediated pipeline and the pipeline without remediation indicates that the proposed technique substantially mitigates the effects of large deformation. 相似文献
15.
Typical all-steel buckling-restrained braces (BRBs) usually exhibit obvious local buckling, which is attributed to the lack of longitudinal restraint to the rectangle core plate. To address this issue, all-steel BRBs are proposed, in which two T-shaped steel plates are adopted as the minor restraint elements to restrain the core plate instead of infilled concrete or mortar. In order to investigate the factors that characterize the hysterical responses of this device, different finite element (FE) models are developed for the specific context. The FE models are developed based on nonlinear finite element software, which incorporate continuum (shell or brick) elements, large displacement, and deformation formulations. In these FE models, two different steel constitutive models are adopted to precisely reproduce the cyclic response of the BRB component. Meanwhile, comparisons between the numerical and experimental results are conducted to validate the effectiveness and accuracy of the robust FE model. The agreements between experimental observations and numerical predictions demonstrate that the FE method could be utilized for in depth parametric analysis. Furthermore, BRBs with detailed configurations can provide excellent hysteretic behavior and seismic performance through the optimal design process. 相似文献
16.
Underground utility tunnels are the most fundamental and reliable lifeline network in urban cities,and are widely constructed throughout the world.In urban areas,most utility tunnels usually encounter the non-homogeneity of subsoil condition due to various construction effects.Studies have shown that the damage mechanism of shallow underground structures mainly depends on the inhomogeneity of the subsoil conditions.This would become a considerable factor for the stability of the underground utility tunnel structures.However,this type of research still needs to establish the vulnerable seismic design.In this study,a series of shaking table tests were conducted on non-homogenous soils to investigate the performance of seismic interaction between utility tunnels,surrounding soils and interior pipelines.The dynamic responses measured from the test account for the boundary condition of non-homogeneous soils,the internal forces,displacement of tunnel joints,the dynamic characteristics on interior pipelines and the reasonable spring stiffness with damping in the seismically isolated gas pipeline model inside the tunnel.The vulnerability of underground utility tunnel in non-homogeneous soil zone and the mechanism of the stability of interior facilities are the main topics discussed in this paper. 相似文献
17.
In order to further improve the seismic performance of RC shear walls, a new composite shear wall with concrete filled steel
tube (CFT) columns and concealed steel trusses is proposed. This new shear wall is a double composite shear wall; the first
composite being the use of three different force systems, CFT, steel truss and shear wall, and the second the use of two different
materials, steel and concrete. Three 1/5 scaled experimental specimens: a traditional RC shear wall, a shear wall with CFT
columns, and a shear wall with CFT columns and concealed steel trusses, were tested under cyclic loading and the seismic performance
indices of the shear walls were comparatively analyzed. Based on the data from these experiments, a thorough elastic-plastic
finite element analysis and parametric analysis of the new shear walls were carried out using ABAQUS software. The finite
element results of deformation, stress distribution, and the evolution of cracks in each phase were compared with the experimental
results and showed good agreement. A mechanical model was also established for calculating the load-carrying capacity of the
new composite shear walls. The results show that this new type of shear wall has improved seismic performance over the other
two types of shear walls tested. 相似文献
18.
The maximum seismic displacements of a structure can be used for the assessment of its post-earthquake performance. In this paper, a simple and efficient procedure is proposed for determining maximum seismic displacements of planar steel frames from their residual deformation. More specifically, the inelastic behaviour of 36 moment resisting steel frames and 36 concentrically X-braced steel frames under one hundred strong ground motions is investigated. Thus, on the basis of extensive parametric studies for these structures and seismic records, empirical equations are constructed for simple and effective prediction of maximum seismic displacements from residual deformation, which can be measured in-situ after strong seismic events. It is found that the usage of residual deformation can be effectively utilized to evaluate the post-earthquake performance level of steel structures. 相似文献
19.
In addition to the normal service loadings, engineering structures may be subjected to occasional loadings such as earthquakes, which may cause severe destruction. When the steel rebar is corroded, the damage could be more serious. To investigate the seismic performance of corroded RC columns, a three-dimensional mesoscale finite element model was established. In this approach, concrete was considered as a three-phase composite composed of aggregate, mortar matrix and interfacial transition zone (ITZ). The nonlinear spring were used to describe the bond slip between steel and concrete. The degradation of the material properties of the steel rebar and cover concrete as well as the bonding performance due to corrosion were taken into account. The rationality of the developed numerical analysis model was verified by the good agreement between the numerical results and the available experimental observation. On this basis, the effect of corrosion level, axial force ratio and shear-span ratio on the seismic performance of corroded RC columns, including lateral bearing capacity, ductility, and energy consumption, were explored and discussed. The simulation results indicate that the mesoscopic method can consider the heterogeneity of concrete, to more realistically and reasonably reflect the destruction process of structures. 相似文献
20.
A series of shaking table tests on a 1:12‐scale model using scaled TaftN21E earthquake records were conducted to investigate the seismic performance of a 17‐storey high‐rise reinforced concrete structure with a high degree of torsional eccentricity and soft‐storey irregularities in the bottom two storeys. Based on the analysis of test results, the following conclusions were drawn: (1) the model responded mainly in the coupled mode of translation and torsion or in the torsional mode. Under severe table shaking, the flexible side underwent large inelastic deformation, and the predominant mode of the model changed from the coupled mode to the torsional mode, resulting in greatly increased torsional stiffness, thereby limiting damage in the flexible frame; (2) the shear force and deformation of the flexible side were governed by the torsional behaviour, whereas those of the stiff side were affected mainly by the overturning deformation. The lateral stiffness of the shear wall in the torsional mode was about four times that in the coupled mode because the warping deformation due to torsion counteracted the flexural deformation due to overturning moment in the torsional mode; and (3) the reversed cyclic overturning moments predicted by linear elastic dynamic analysis in the direction transverse to the table excitations contradicted unilateral overturning moments of the serviceability‐level test results, which showed a bias towards tension or compression in the columns. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
|
下载免费PDF全文