共查询到20条相似文献,搜索用时 187 毫秒
1.
2.
3.
为研究复合外套型电气设备的抗震性能与安装减震装置后的减震效果,对其进行特高压交流CVT地震模拟振动台试验研究,分析设备的动力特性与地震响应。白噪声试验结果表明试验设备安装减震器后其结构第一阶频率由1.07Hz略降低至1.04Hz,即减震装置对结构的整体刚度影响较小;人工波试验中原结构在地震动峰值加速度0.2g(PAG=0.2g)抗震试验中设备最大应力与位移响应为46.33 MPa与349.12mm,减震结构在PAG=0.5g抗震试验中,设备最大应力与位移响应为27.64 MPa与330.06mm,设备安装减震装置后抗震性能得到显著提升。试验研究结果可为复合材料电气设备抗震性能研究与减震装置应用提供参数数据。 相似文献
4.
基于随机反应谱理论的支柱类电气设备抗震性能评估方法研究 总被引:1,自引:0,他引:1
主要开展了支柱类电气设备结构的抗震性能评估问题研究。建立了针对电气设施结构支架动力放大系数选取安全性的一种评估算法。首先采用随机反应谱法考虑地震荷载的随机性,建立了地震影响系数的极值I型概率分布;然后通过蒙特卡洛一般抽样方法进行地震反应谱荷载样本的随机投放,并采用有限元法计算样本荷载下支柱类电气设备结构的地震响应;最终依据地震响应量及设计阈值表达的功能函数实现结构设计方案可靠度指标的评估计算。工程算例表明,通过本文方法可以实现支架类电气设备结构抗震设计方案的可靠性评估。 相似文献
5.
在核电站中:核电设备通过不同的固定条件与结构相连,地震作用时设备与结构动力相互作用复杂,为分析核电设备多维地震响应并鉴定其抗震性能,进行了考虑不同固定条件的核电设备多维地震响应振动台试验研究。振动台试验进行了5次运行基准地震和1次安全停堆地震的动力时程激振,以及试验首末2次动力特性测试。试验结果表明:不同固定条件会影响核电设备多维地震响应的加速度峰值、反应谱特性和动力放大系数,与设备直接固定于振动台相比,将核电设备悬挂固定于剪力墙再与振动台连接的固定条件,改变了设备反应谱特性,且放大了响应的加速度峰值,具有显著的动力放大效应,使核电设备多维地震响应更为强烈。因此,对此类固定条件的核电设备,在产品设计及安装固定时要充分考虑动力放大效应,以提高设备的抗震韧性。抗震试验前后,核电设备功能运行正常,结构完整性好,抗震性能满足要求。 相似文献
6.
7.
8.
9.
为研究复合材料电气设备抗震性能与减震技术应用效果,对特高压复合支柱材料绝缘子进行了抗震与减震地震模拟振动台试验,研究了设备动力特性和地震响应。白噪声试验结果表明:该复合材料支柱绝缘子在安装减震器后第1阶频率由1.11 Hz降低到1.04 Hz,表明减震器对设备结构的整体刚度影响较小。3种地震波试验结果表明:设备地震响应与地震动峰值加速度在抗震试验中呈线性变化关系,但在减震试验的应力响应中呈非线性变化关系;设备安装减震器后,试验地震动峰值加速度越大,减震效率越高,最高达到了66.32%;而位移减震率与地震动峰值加速度无明显规律,最大位移减震率为49.36%。试验研究结果表明:试验设备安装减震器后抗震性能得到显著提升,为复合材料电气设备抗震性能研究与减震技术应用提供了参考依据。 相似文献
10.
附建式变电站通常会对电气设备采取隔振措施以减小设备振动及噪声通过结构传播扰民。然而,目前常用的隔振装置系统的自振频率通常位于2~10 Hz之间,与地震动卓越频率相近。因此,这类隔振装置在地震发生时,往往无法发挥隔震效果,反而可能会放大地震的作用,导致采用了隔振措施的电气设备更容易受到损坏。通过有限元模拟的方法,旨在研究不同周期类型的地震动激励下,采用常规隔振方案的电气设备的动力响应。结果表明,采用普通隔振装置后,电气设备所受的竖向地震作用响应相较楼板处有不同程度的放大。这一发现对电气设备的抗震设计提出了重要的警示,需要更加谨慎地考虑隔振装置的选用,以确保设备在地震发生时能够有效地减小振动,降低损坏风险。 相似文献
11.
针对核电厂CAP1400核岛结构地震反应问题,构建了核岛屏蔽厂房和辅助厂房整体结构的3个分析模型:原型和1/16、1/40缩尺模型,并在AP000谱和RG1.60谱地震动输入下进行了有限元模拟对比分析,探讨了振动台试验模型缩尺处理的合理性和精确性。研究表明,基于缩尺模型得到的结构自振频率相对于原型结构模型有所降低,降低幅度在8.5%以内;结构模型的缩尺对结构反应峰值加速度和高频(大于3Hz)加速度反应谱的影响较为显著,但对较低频(小于3Hz)的加速度反应谱影响较小;模型缩尺对结构不同方向反应的影响中,刚度越大的方向其影响越大。进一步将结构模型数值模拟结果与1/16缩尺模型的振动台试验结果进行了比较分析,试验给出的结构自振频率远低于模型数值模拟结果,但原型和1/16缩尺模型数值模拟得到的结构反应均与试验结果较为接近。基于模型数值模拟和振动台试验研究,认为对于缩尺比1/16或更大的模型可以忽略模型的缩尺效应。 相似文献
12.
瀑布沟水电站水库天然地震本底特征 总被引:1,自引:0,他引:1
瀑布沟水电站处于相对稳定的瓦山断块上,水库的库尾位于龙门山断裂带、鲜水河断裂带、安宁河断裂带的交汇部位,地震活动相对强烈。了解和掌握水库蓄水前库坝区及其周围天然地震活动背景水平,可对水库诱发地震的危险性进行前期评价,为蓄水后的诱发地震活动监测预测提供可靠的鉴别依据。在水库蓄水前瀑布沟水库地震台网一期运行逾3年,二期运行逾1年,本文用这批资料提供库区及附近蓄水前天然地震活动水平确切实用的各项指标。用全国和四川台网地震资料,给出含库区的较大区域地震活动背景和对库区的影响,同时给出库区及附近ML≥2.5地震的活动特征。 相似文献
13.
14.
为评估某型号1 100kV特高压(UHV)气体绝缘开关设备(GIS)瓷套管的抗震性能,将其连同支撑筒体与支架一起安装在振动台上,开展特高压气体绝缘开关设备瓷套管振动台试验。试验采用符合特高压标准反应谱的人工波激励该瓷套管,得到瓷套管关键部位的加速度、位移和应变响应。运用数值仿真软件ABAQUS对该振动台试验进行数值仿真研究,分析试验模型的自振频率、套管根部应力和套管顶端相对位移,得到与试验结果吻合较好的结果,证明该数值仿真模型的有效性。通过数值仿真的手段研究套管固有频率和本体(支撑筒体和支架)刚度的变化对套管抗震性能的影响,结果表明:该套管固有频率在一定范围内变化时,其地震响应相对较小;随着本体刚度的增大,套管根部最大应力与套管顶端最大相对位移均呈下降的趋势,因此适当增大本体的刚度可以降低套管的地震响应。 相似文献
15.
为研究近断层地震动特性对火灾后多层RC框架抗震性能的影响,以火灾后某多层RC框架结构为研究对象,结合火灾后现场材料的检测与鉴定报告,开展了结构火灾前后在近场有脉冲和无脉冲地震作用下的结构动力弹塑性时程分析,对比分析了近场有脉冲和无脉冲地震动特性对火灾前后RC框架结构整体的抗震性能的影响.研究结果表明:火灾后,整体结构地... 相似文献
16.
为了研究多层空心砌块房屋混凝土结构抗震性测试,按照1∶5缩尺比例建造空心砌块房屋混凝土结构模型进行抗震性测试实验。根据实际原型参数遵从相似理论的要求选择模型参数,通过电液伺服加载装置和液压千斤顶加载水平、垂直方向荷载,对所建造模型进行动力特性测试、地震反应分析、结构最大地震反应以及位移响应进行了实例分析。结果表明,随着破坏程度加大,模型结构自振频率随之减小,阻尼比随之增大;有芯柱多层空心砌块房屋模型的抗震效果较强;强震状态下,结构动力特性变化较大,破坏层聚集了房屋结构的最大反应;当加速度为125 cm/s时,结构最大位移为2.73 mm,低于规范值,模型结构具备一定延性。 相似文献
17.
Because a conventional isolation system with constant isolation frequency is usually a long‐period dynamic system, its seismic response is likely to be amplified in earthquakes with strong long‐period wave components, such as near‐fault ground motions. Seismic isolators with variable mechanical properties may provide a promising solution to alleviate this problem. To this end, in this work sliding isolators with variable curvature (SIVC) were studied experimentally. An SIVC isolator is similar to a friction pendulum system (FPS) isolator, except that its sliding surface has variable curvature rather being spherical. As a result, the SIVC's isolation stiffness that is proportional to the curvature becomes a function of the isolator displacement. By appropriately designing the geometry of the sliding surface, the SIVC is able to possess favorable hysteretic behavior. In order to prove the applicability of the SIVC concept, several prototype SIVC isolators, whose sliding surfaces are defined by a sixth‐order polynomial function, were fabricated and tested in this study. A cyclic element test on the prototype SIVC isolators and a shaking table test on an SIVC isolated steel frame were all conducted. The results of both tests have verified that the prototype SIVC isolators do indeed have the hysteretic property of variable stiffness as prescribed by the derived formulas in this study. Moreover, it is also demonstrated that the proposed SIVC is able to effectively reduce the isolator drift in a near‐fault earthquake with strong long‐period components, as compared with that of an FPS system with the same friction coefficient. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
18.
Earthquake simulator tests of a 1/6-scale nine-story reinforced concrete frame-wall model are described in the paper. The test results and associated numerical simulation are summarized and discussed. Based on the test data, a relationship between maximum inter-story drift and damage state is established. Equations of variation of structural characteristics (natural frequency and equivalent stiffness) with overall drifts are derived by data fitting, which can be used to estimate structural damage state if structural characteristics can be measured. A comparison of the analytical and experimental results show that both the commonly used equivalent beam and fiber element models can simulate the nonlinear seismic response of structures very well. Finally, conclusions associated with seismic design and damage evaluation of RC structures are presented. 相似文献
19.
IntroductionEarthquake prediction is still one of most difficult problems in the world although the researches on it in China have been done for more than 30 years. A lot of experience, however, has been accumulated and some theoretical study on earthquake prediction conducted so that some prediction could be issued prior to earthquakes to obtain real effectiveness of mitigating disasters from these earthquakes to some extent, in China. The annual national consulting convention of earthquake … 相似文献
20.
The purpose of this study is to investigate the effect of retrofitting dynamic characteristics of a damaged laboratory arch dam model, subsequently repaired with high-strength structural mortar and strengthened with composite carbon fiber reinforced polymer. This study constructed in laboratory conditions is a prototype arch dam–reservoir–foundation model. Five test cases of ambient vibration on the arch dam model illustrate the changes in dynamic characteristics: natural frequency, mode shape, and damping ratio, before and after retrofitting. The ambient vibration tests collected data from the dam body during vibrations by natural excitations which provided small impacts and response signals from sensitivity accelerometers placed at crest points. Enhanced Frequency Domain Decomposition Method in the frequency domain extracts the experimental dynamic characteristics. At the end of the study, experimentally identified dynamic characteristics obtained from all test cases have been compared with each other. Apparently, after the retrofitting, the natural frequencies of the dam body increased considerably, demonstrating that the retrofitting, including repairing and strengthening is very effective on the flashback of initial dynamic characteristics. 相似文献