首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
针对利用侧扫声纳检测海底管道时因其检测声影图像模糊而导致管道悬空高度检测误差过大的问题,提出了侧扫声纳声波掠射角优化设计的思路及方法。阐述了利用侧扫声纳对海底管道进行检测的工作原理,并利用海底管道和海底底质反向散射强度的计算公式探讨了声波在海底的反向散射强度、侧扫声纳声影图像的质量以及声波掠射角的取值这三者之间的关系对海底管道悬空高度h计算精度的影响,从理论上确定声波掠射角最佳取值范围的存在。通过工程实例的现场检测与比对试验,获得了在本试验所处海域环境中利用侧扫声纳检测海底管道时声波掠射角的最佳取值范围,对于类似的海底管道检测工程具有一定的指导意义。  相似文献   

2.
侧扫声纳图像变形现象与实例分析   总被引:4,自引:0,他引:4  
王闰成 《海洋测绘》2002,22(5):42-45
依据侧扫声纳成像原理,研究了由于声速变化、声波束倾斜和海底坡度改变等因素所致的声图像变形现象。结合飞机残骸、港池地形等典型声图像,分析了变形原因与判释方法。  相似文献   

3.
一、相干声纳系统的特点 人们对回声测深仪、侧扫声纳、多波束测深仪都比较熟悉了,近年来又出现一种可对海底地貌高密度、高精度测量的相干声纳系统。什么是相干声纳(interferometric seabed inspectric sonar)呢?它是一种利用多声板接收回波的振幅、时间和相位差来对海底各点准确定位,并快速采集和处理大量的数据的系统。相干声纳(缩写ISIS)集水深探测技术和成像技术于一体,不仅可以测量水深,而且可以同时给出海底三维立体图、等深图、侧扫声图。  相似文献   

4.
针对侧扫声纳图像目标边缘检测困难的问题,利用二维离散小波变换对侧扫声纳(SSS)声图进行多分辨率分析,对大尺度分解的小波系数进行非极大值抑制,并重构小尺度上的低频分量。联合各尺度上的低频分量,构建SSS声图像素点处特征向量,构成其特征空间,对特征空间进行主成分分析,压缩其维数,并对压缩后的特征向量进行K-均值聚类分析,提取类间边缘线。利用含有沉船的SSS声图,并在其均质区域内加入目标与声影进行验证实验。该方法在实验中边缘检测准确率为0.90,表明该方法的有效性。  相似文献   

5.
基于粒子群优化算法的PSO-BP海底声学底质分类方法   总被引:2,自引:2,他引:0  
利用粒子群优化算法(PSO)较强的鲁棒性和全局搜索能力等优点,将PSO算法与BP神经网络相结合,优化了BP神经网络分类时的初始权值和阈值。基于珠江河口三角洲的侧扫声呐图像数据,提取了海底声呐图像中砂、礁石、泥3类典型底质的6种主要特征向量,利用PSO-BP方法对海底底质进行分类识别。实验表明,3类底质分类精度均大于90%,高于BP神经网络70%左右的分类精度,表明PSO-BP方法可有效应用于海底底质的分类识别。  相似文献   

6.
侧扫声纳是海洋测绘领域的常用设备,为解决侧扫声纳波束模式带来的声纳图像中央区域质量较差的问题,提出了侧扫声纳图像中央区的自动确定和重建方法。首先根据侧扫声纳测量原理,基于波束模式,自动确定侧扫声纳图像的中央区域;然后根据图像强度梯度和像素可靠信息,计算图像重建区域的优先级;最后根据优先级顺序,采用基于样例的方法对中央区进行重建,提高侧扫声纳图像质量。研究表明,重建后的侧扫声纳图像无论是在主观视觉还是客观评价指标方面,都取得了满意的结果。采用本文所提方法得到的重建图像,能够清晰地反映海底特征,具有很好的应用价值。  相似文献   

7.
为研究西沙宣德环礁海底地貌特征及珊瑚分布情况,采用舷挂侧扫拖鱼的方式对环礁区域海底进行地貌扫测,从采集的侧扫声呐图像上可以识别出环礁区域珊瑚分布情况及珊瑚礁区地貌特征,利用侧扫声呐图像识别方法结合实物样品比对可以圈定出珊瑚分布范围、暗礁区域及环礁区域底质类型分布,采用基本的数学处理方法定量分析了水下珊瑚礁体的海底高度及疑似沉船的大小,分析了侧扫声呐图像显示的调查船转向效应。  相似文献   

8.
针对侧扫声呐数据采集的特点,提出了一种基于图像边缘检测技术中LOG算子的海底线检测新方法,用于准确检测海底线从而对侧扫声呐资料进行斜距改正。通过实验数据处理,表明该方法较传统方法具有明显的优势。  相似文献   

9.
侧扫声纳和多波束测深系统在海洋调查中的综合应用   总被引:12,自引:2,他引:12  
罗深荣 《海洋测绘》2003,23(1):22-24
介绍了利用多波束进行全覆盖水深测量和利用侧扫声纳进行海底、水体目标的探测技术。综合利用多波束水深数据和侧扫声纳声图,可有效增强不同观测数据的互补性和提高工程质量。  相似文献   

10.
文章简要介绍侧扫声呐和单道地震系统的工作原理,并以海南岛南部近海海域为例,分析通过侧扫声呐图像和单道地震剖面提取沙波、沙脊、海底礁石和陡坎等海底微地貌的可行性及其过程。研究表明:沙波和海底礁石可通过对侧扫声呐图像的判读和识别,对比单道地震剖面图,直接在侧扫声呐图像上圈定;陡坎和沙脊可通过对单道地震剖面图的判读和识别,提取海底水深剖面数据制作平面剖面图,并结合潮流动力方向圈定;综合利用侧扫声呐和单道地震数据,可有效提高海底微地貌的解译精度。  相似文献   

11.
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.  相似文献   

12.
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.  相似文献   

13.
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.  相似文献   

14.
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.  相似文献   

15.
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.  相似文献   

16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明:土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。  相似文献   

17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.  相似文献   

18.
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.  相似文献   

19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.  相似文献   

20.
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号