共查询到18条相似文献,搜索用时 156 毫秒
1.
光纤陀螺寻北方案的比较 总被引:2,自引:0,他引:2
本文介绍了光纤陀螺寻北的基本原理和几种主要的寻北方案,并对几种寻北方案进行了比较分析,认为二位置寻北方案利用转位消除了陀螺的常值漂移,可降低对陀螺精度的要求,是一种易于实现的方案。二位置寻北方案利用陀螺敏感在相差1800的两个方向上的地球自转角速率水平分量,精确地解算出真北方向与陀螺轴向的夹角。 相似文献
2.
3.
为了实现单自由度陀螺寻北仪自动寻北,通过分析寻北仅运动规律,本文建立了其寻北数学用到,分别为:模型Ⅰ——时间作为观测值,模型Ⅱ——角位置作为观测值,模型Ⅲ——时间及角位正同时作为观测值,楼四Ⅳ——最小二乘谱分析模型.通过模拟实验,认为自国对具有较强的抗干扰能力,适合单自由反陀螺寻北仪的数据采集和处理. 相似文献
4.
5.
6.
光纤陀螺寻北仪利用光纤陀螺测量地球自转角速率的水平分量来获得被测点的北向信息,利用加速度计测量固定陀螺的基座的倾斜角度,经过解算得到载体的参考轴与真北方向的夹角。转位控制方案设计是寻北仪系统设计中一个极其重要的环节,转位机构的转位精度必须满足陀螺寻北的精度要求。文中详细介绍了光纤陀螺寻北仪的组成、转位控制方案设计及其实现途径。实验证实采用光电编码器作为直流电机位置控制的反馈元件的转位机构达到了系统寻北的精度要求。 相似文献
7.
基于双位置的磁悬浮陀螺异常数据检测 总被引:1,自引:0,他引:1
针对磁悬浮陀螺全站仪在极端工作环境下受异常数据干扰的问题,该文提出了一种利用磁悬浮陀螺双位置采样数据特征进行异常数据检测、剔除的数据处理方法。采用回归分析的方法对理想工作状态下的磁悬浮陀螺双位置采样数据与陀螺寻北方位间的函数关系进行拟合分析;通过区间预测的方法明确了陀螺寻北信息中异常数据的检验标准,并依据该标准实现了对寻北观测值中粗差等异常数据信息的有效识别。工程实测数据的验证结果表明:该检验法可以有效地对磁悬浮陀螺寻北数据中的异常值信息进行分离,提高陀螺寻北定向精度。 相似文献
8.
9.
10.
11.
为消除基座扰动对非陀螺寻北系统测量精度的影响,采用小波消噪技术对系统的输出信号进行处理。提出了利用信号在多尺度下小波变换系数中,其有用信号为平稳信号,而干扰噪声的模极大值并不随小波分解尺度增加而减少的特性,来确定基座扰动在时域上的作用点,消除影响后再进行小波变换消噪的方法。通过实验证明,该方法能有效提高系统的寻北精度,并增强系统在大幅度基座扰动下快速寻北的鲁棒性。 相似文献
12.
为了削弱光纤陀螺信号中异常噪声对寻北精度的影响,在滤除高频周期噪声的基础上,提出了一种处理陀螺信号的新算法。推导了陀螺信号的抗差解公式及其误差影响函数,取观测值的中位数作为抗差初值,利用一次抗差估计求得的观测残差再用中位数法求得均方差因子,并给出了高崩溃污染率的初值辅以IGGⅢ方案迭代解算的混合算法。计算结果表明,基于可靠初值和均方差因子估值的抗差估计可以有效削弱异常干扰对陀螺的影响。 相似文献
13.
14.
在脉冲星导航中,角位置误差是主要的误差源之一。因此本文基于X射线脉冲星导航,提出了一种修正扩维无迹卡尔曼滤波(MASUKF)算法进行角位置误差的改进。MASUKF算法在原扩维无迹卡尔曼滤波(ASUKF)算法的基础上加入了Roamer延迟的高阶项,并将其作为误差项,将修改后的误差项代入状态方程与量测方程中,即可进行仿真分析。在仿真中,首先将ASUKF算法与UKF算法进行对比仿真模拟试验,结果显示ASUKF算法能显著地提高约45 m的定位精度,在X、Y、Z 3方向的速度误差估计精度约提高了20%;然后比较ASUKF与MASUKF算法,结果显示MASUKF算法较ASUKF算法的速度误差与位置误差的估计精度均提高2%以上。 相似文献
15.
16.
LIN Xueyuan LI Tingjun QIU Libo LIN Yu 《地球空间信息科学学报》2006,9(2):89-93
IntroductionDouble-Star is to use two stationary orbit satellitesto locate the target which is located in the overlayarea of the the satellites’wave-beam. The two sat-ellites can only supply two equations. In order toget the three-dimensional position of… 相似文献
17.
ZHANGXiaohong LIUJingnan 《地球空间信息科学学报》2004,7(3):218-224
The error sources related to the laser rangefinder, GPS and INS are analyzed in details. Several coordinates systems used in airborne laser scanning are set up, and then the basic formula of system is given.This paper emphasizes on discussing the kinematic offset correction between GPS antenna phase center and laser fired point. And kinematic time delay influence on laser footprint position, the ranging errors, positioning errors, attitude errors and integration errors of the system are also explored. Finally, the result shows that thekinematic time delay can be neglected as compared with other error sources. The accuracy of the coordinates is not only influenced by the amplitude of the error, but also controlled by the operation parameters such as flight height, scanning angle amplitude and attitude magnitude of the platform. 相似文献
18.
The error sources related to the laser rangefinder, GPS and INS are analyzed in details. Several coordinates systems used in airborne laser scanning are set up, and then the basic formula of system is given. This paper emphasizes on discussing the kinematic offset correction between GPS antenna phase center and laser fired point. And kinematic time delay influence on laser footprint position, the ranging errors, positioning errors, attitude errors and integration errors of the system are also explored. Finally, the result shows that the kinematic time delay can be neglected as compared with other error sources. The accuracy of the coordinates is not only influenced by the amplitude of the error, but also controlled by the operation parameters such as flight height, scanning angle amplitude and attitude magnitude of the platform. 相似文献