共查询到18条相似文献，搜索用时 187 毫秒
1.
桩-筒组合基础是将单桩基础与筒型基础组合的一种新型海上风电基础形式,其受力模式不同于传统桩基基础,优点是可通过合理减小桩长、桩壁厚等途径提高承载性能。基于极限地基反力法,提出单层黏土中桩-筒组合基础受力模式及水平承载力的计算方法。利用力加载和位移加载两种控制方法进行数值分析,研究水平承载性能的影响因素。结果表明,在一定范围内,桩-筒组合基础水平承载性能随桩入土深度、桩壁厚、筒外径的增大而提高。基于实际工程,对等用钢量的单桩基础与组合基础进行比较计算,结果表明,桩-筒组合基础可有效降低基础倾斜度和位移,提高承载性能。 相似文献
2.
p-y 曲线法在水平受荷桩的设计中得到了广泛应用,然而近年来在海上风机超大直径单桩基础设计中受到了学术界和工程界的质疑,当前研究表明,桩基尺寸是产生这一问题的主要原因。本文通过三维数值仿真技术,研究了砂土地基中水平受荷桩-土作用特征的演变规律,探讨了当前超大直径单桩设计方法存在的主要问题及产生的原因。计算结果显示：超大直径单桩基础因其桩径大、长径比（入土长度与直径的比） 小的尺寸特征,在水平荷载作用下桩土作用具有明显的三维空间效应,即除受水平向土反力外,还受到桩端水平向的摩擦力、沿桩身不均匀摩阻力产生的抵抗力矩及桩底不均匀土反力提供的抵抗力矩;进一步研究表明,后三类抗力对桩基水平承载力的贡献占比与桩基尺寸有关,即桩基直径越大、长径比越小,这些抗力的贡献越大。因此,在水平受荷超大直径单桩承载特性计算与分析的过程中,除当前水平向p-y 弹簧提供的抗力外,还应考虑桩底的水平剪力、桩身摩擦力和桩底反力不平衡产生的抵抗力矩。 相似文献
3.
为改善海上风电大直径钢管桩的水平承载性能,基于ABAQUS有限元软件对单桩改进形式的加翼桩结构进行了系统研究,计算分析了软黏土地基中加翼桩在水平荷载作用下桩身弯矩、应力、位移、桩身泥面处倾斜率和极限承载力,研究了加翼桩面积、形状、埋深和刚度等翼板参数对加翼桩水平承载性能的影响规律,根据加翼桩的桩-土作用机理,参考现行规范模式提出适用于软黏土地基大直径钢管桩的P-Y曲线。研究结果表明,加翼桩通过在泥面处设置翼板可降低桩基泥面处倾斜率50%、提高桩基极限承载力60%以上,加翼桩水平承载性能明显优于单桩。 相似文献
4.
5.
离岸深水全直桩码头承载性能有限元分析 总被引：1，自引：0，他引：1
全直桩码头是适于软土地基上离岸深水海域的新型高桩码头结构型式,其承载机理与传统高桩码头存在较大差异,且软土地基循环软化效应显著。建立全直桩码头结构与地基相互作用三维弹塑性有限元模型,基于二次开发采用拟静力法对土体循环软化效应进行模拟。通过有限元模型研究全直桩码头的承载特性与破坏模式,并探讨水平极限承载力的影响因素。研究表明水平荷载作用下,基桩的塑性破坏是结构失稳的控制因素,地基土体的承载力对结构水平极限承载力不起决定性作用;竖向荷载作用下,结构竖向极限承载力由地基土体强度决定。研究范围内入土深度对结构水平极限承载力影响不大,但桩壁厚度减小或考虑土体软化后,结构水平极限承载力明显降低。设计中,增加入土深度可有效减小土体软化引起的水平极限承载力降低程度,且应考虑结构腐蚀和土体软化对水平极限承载力的双重降低效应,为钢管桩预留足够的腐蚀富裕量。 相似文献
6.
7.
在海上风电单桩基础水平承载力的设计中,风荷载和波浪荷载是两个最主要的常规水平荷载,需要考虑在波浪荷载和风荷载的不同荷载组合下的桩土相互作用。利用有限元软件ABAQUS构建桩土相互作用模型,对桩基施加不同组合的环境荷载,研究桩土的相互作用。在固定环境荷载的情况下,将土体分层,研究不同土质条件下桩基水平承载力的差异。分析可得极端海况下桩身泥面位移约是正常海况下的5倍,且桩身水平位移主要由风荷载引起。桩周土体所受水平应力与桩体的摆动幅度相关,且桩基摆动对桩周土体水平变形的影响范围有限,以桩基为中心1.7倍桩径范围内土体所受影响显著。海床上层土体的强度对桩基水平承载力起关键性作用,上软下硬海床与纯软土海床相比水平承载力大约提高25%,而上硬下软海床与纯软土海床相比水平承载力约提高3倍。 相似文献
8.
9.
针对海相软土地区螺旋钢管桩承载力低与腐蚀问题,提出一种新型压力注浆螺旋钢管桩,并设计5根足尺试验桩,进行现场抗拔承载性能试验,研究螺旋叶片直径与排布方式对成桩直径与桩基抗拔承载性能的影响.结果表明,成桩直径与螺旋叶片直径呈正相关,在每节延长段钢管末端设置螺旋叶片利于提高水泥土柱完整性,使成桩直径更为饱满,提高桩基的抗拔承载性能.将试验结果和现行规范抗拔极限承载力计算结果进行对比,计算结果约为实测平均值的94％,在此基础上提出压力注浆螺旋钢管桩抗拔承载力计算参数修正建议,为后续的设计提供参考. 相似文献
10.
初始几何缺陷被认为是影响管道极限承载力和稳定性的重要因素,但是大部分的管道力学特性研究都没有考虑初始缺陷的影响。基于管道几何尺寸测量机,获得管道的壁厚和直径沿轴向以及环向的分布规律。据此建立了四个三维实体有限元模型,分别为完好管道模型、只考虑直径缺陷的管道模型、只考虑壁厚缺陷的管道模型以及考虑所有缺陷的管道模型。分析了初始缺陷对管道的极限内压承载力、极限轴力承载力和极限弯矩承载力的影响。结果表明,直径缺陷对管道的极限内压承载力影响较大;壁厚缺陷对管道在复杂荷载作用下的极限弯矩承载力影响较大。 相似文献
11.
螺旋桩芯劲性复合桩（helix stiffened cement mixing pile,简称HSCM桩）是一种新型复合桩,其成桩工艺会对桩身及其承载性能有较大影响。为验证HSCM桩在软黏土中同步旋进注浆工艺的可行性,并研究其成桩参数对抗压承载性能的影响,设计了2组缩尺模型试验,包括不同叶片数量与钻进速度的HSCM桩与对比螺旋桩。通过在高岭土制备的软黏土中成桩,并进行抗压承载性能及桩身几何尺寸测试,分析HSCM桩的成桩参数与水泥土桩身间的关系。试验结果表明：同步旋进注浆工艺能够在螺旋桩周围形成倒圆台状的水泥土桩身,水泥土桩身的平均黏结直径约为叶片直径的1.17～1.35倍;适当增加叶片数量能够使水泥与土体充分拌和,提高水泥土桩身的完整性与连续性,以改善HSCM桩的成桩质量;钻进速度大幅提高会导致注浆量不足,减小水泥土桩身的黏结直径与刚度;试验条件下HSCM桩的抗压极限承载力是螺旋桩的3.83～3.93倍,桩径扩大提高了侧摩阻力,注浆工艺加固并提高了土体强度,弥补了叶片在旋进过程中扰动土体造成强度降低的问题。 相似文献
12.
利用室内半模试验和颗粒流数值模拟,揭示多层砂土地基扩底桩单桩抗压承载特性及变形特征。结果表明,通过对比分析极限承载力与H_h/D(持力层厚度与扩大头直径之比)的关系可以看出,单桩的抗压极限承载力随H_h/D逐渐增加,当H_h/D超过2.0时,极限承载力基本不再增加,此时的单桩抗压极限承载力稳定在300.01~303.25 N,是H_h/D=0.5时极限承载力(183.83 N)的1.65倍。扩大头下部土体发生局部压缩-剪切破坏,破坏面从扩大头底面边缘向斜下方扩展,在水平方向影响范围达到最大后逐渐向桩内侧收缩;荷载作用越大,地基破坏区域越大,相应的极限抗压承载力也越大;持力层厚度增加,扩大头分担的荷载比例增大,分担的荷载达到稳定需要的桩顶位移也越大,H_h=0.5 D试验扩大头分担的荷载比例稳定时为60%,对应的桩顶位移约为29 mm;桩顶位移达到33 mm后,H_h=1.0~3.0 D试验稳定在63%~65%之间;通过细观颗粒流理论对砂土移动特性的研究发现,持力层厚度从0.5 D增大至2.0 D,破坏面的起始扩展角度从31°增大至42°。数值模拟研究结果与模型试验数据吻合效果良好,证明该方法分析多层砂土地基扩底桩单桩抗压荷载传递机理是可行的。 相似文献
13.
The shaft resistance of rock-socketed piles depends not only on the properties of its surrounding rock, but also on the radial force induced by the load imposed on the top of the pile. This paper deduced a plastic zone of rock around a single pile and obtained the shaft resistance of a rock-socketed pile based on the theories of cavity expansion and shear strength. The research results showed that the magnitude of the radial force in the socketed portion of a rock-socketed pile was related to the pile diameter, Poisson’s ratio, and properties of the surrounding rock. The influence area of rock decreased with increasing pile diameter. The radial force and lateral friction decreased with the increasing relative stiffnesses of the pile and rock. The radial stress on the elastic–plastic interface can be analytically determined based on the rock properties and depth. A field test was used to validate the proposed method, and a good agreement was obtained between the field data and predicted results of the proposed method. The research results in this paper are beneficial to guide actual practice. 相似文献
14.
Javad Khazaei 《Marine Georesources & Geotechnology》2017,35(4):528-537
Piling procedure may disturb the surrounding soil, due to the installation particularly for cast-in-place piles. It causes a reduction in the soil strength parameters and, consequently, pile capacity. To overcome shortcomings and also for improving piles’ capacity, postgrouting as a compensation method is recognized and more developed in recent years. Helical piles, those are used widely in marine and land projects, although, are driven by torque implementation, but soil disturbance is noticed, where number of the helices become up to 3 and more. In this paper, an experimental study program is performed by frustum-confined vessel (FCV) to investigate bearing capacity of model helical piles and also postgrouted cases’ performance. FCV has been used because of its linear distribution of vertical and horizontal stresses from zero at top to maximum at bottom which simulates real field stress conditions. Through experimental study, small-scale helical model piles were made of 4-mm-thick steel plate and have been used with a length of 750?mm. The shaft and helix diameters of model piles have been 32 and 89?mm, respectively. So, the helix-to-shaft ratio (wing ratio) was about 2.8. The helical model piles installed in fine-grained sand as a surrounding soil and then axial loading tests before and after grouting were performed to achieve ultimate pile capacity. Results indicated postgrouting can improve both ratios of toe and frictional soil–pile interactions including upgrading β and Nt factors. In addition, the post grouting phenomena can change the pile geometry due to treated soil bond, resulting better functioning. Therefore, it is a proper method to improve helical piles performance and compensate installation effects in capacity mobilization. 相似文献
15.
近年来,潮流能能量转换技术发展迅速,但大型潮流发电机组基础结构方面的研究和应用还并不多见。针对潮流能电站基础结构在抗弯抗剪强度、桩径尺寸方面的特殊要求,结合我国潮流能富集区海底多为浅覆盖层或裸露基岩、且地形复杂的情况,提出了一种新型模块式嵌岩灌注桩基础结构。该基础结构的嵌岩灌注桩通过在桩内布置环形钢板箍和钢筋束来增强抗剪抗弯能力,使其在常规桩径即可满足潮流能电站的支撑要求,减少了对发电水流断面的阻挡;各主体灌注桩可通过横撑、纵撑和斜撑连接构成模块式基础,以适应不同地形条件、不同机组数量和安装方式的要求。新型模块式嵌岩灌注桩基础结构在LHD联合动能公司3.4 MV潮流发电项目中进行了首次应用,获得了良好的使用反馈。 相似文献
16.
Yogendra Tandel Mohsin Jamal Chandresh Solanki Atul Desai Jignesh Patel 《Marine Georesources & Geotechnology》2017,35(4):504-511
Granular piles are frequently used as a method of improving soft grounds as they provide increased bearing capacity and reduce foundation settlements. However, in very soft clayey soils, they may not derive their load-carrying capacity by low confining pressure provided by the surrounding soil. In such circumstances, granular piles may be reinforced with suitable geosynthetic to increase its load-carrying capacity and to reduce excessive bulging. In this study, the performance of small group of geosynthetic-reinforced granular piles (GRGPs) is examined in terms of load-carrying capacity, settlement, and modulus by laboratory model tests. The parameters investigated include modulus of reinforcement material, area replacement ratio (ARR) based on the column diameter and reinforcement length. The results indicated that increasing the modulus of the reinforcement and the ARR based on the column diameter enhances the overall performance of the GRGP group. It was also observed that reinforcement on top portion of the granular pile is sufficient to substantially increase the load-carrying capacity of granular pile group. 相似文献
17.
为了研究桩长对海底防沉板—桩复合基础在水平、弯矩和扭转荷载作用下承载特性的影响,以我国南海水深200 m的某工程实例为研究对象,利用Flac3D有限差分仿真软件建立了计算模型。研究了桩长为4 m、6 m和8 m的防沉板—桩复合基础在水平、弯矩和扭转荷载作用下的极限承载力和荷载传递机理。结果表明,桩长超过6 m时复合基础的水平承载力显著增长,在水平加载过程中,防沉板总是先达到极限状态而破坏,桩基础的贡献在加载后期体现,且桩长为4 m、8 m时,桩基础与防沉板的连接处弯矩最大;随着桩长的增加,复合基础的抗弯承载力大幅提高,桩基础对复合基础的抗弯承载力贡献增大,当桩长超过8 m,桩长的增加对提高复合基础的抗弯承载力意义不大;在弯矩加载过程中,桩长对于防沉板、桩基础的荷载分配有显著影响,桩长为4 m时,外荷载主要由防沉板承担,当桩长超过4 m时,外荷载主要由桩基础承担;当扭转荷载不超过2 100 k N·m时,防沉板承担主要荷载,直至防沉板达到极限状态而发生旋转,随后桩基础的承载力逐渐发挥;对于桩长为6 m、8 m的复合基础,其极限状态根据防沉板适用性准则确定。 相似文献
18.
Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results. 相似文献