首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 389 毫秒
1.
Abstract

An experimental study about the effects of initial conditions of soil and geotextile reinforcement on the mechanical behavior of reinforced sand is presented in this paper. A series of direct shear tests are conducted on reconstituted specimens of dry and moist natural sand prepared with different initial water content (w?=?0, 1.5, 3, and 5%) and including the two arrangements of geotextile layers (one and two layers, respectively). Both S41 and PEC55types of non-woven geotextile were used and placed at different heights of the specimens to investigate the effect of geotextile reinforcement on the behavior of sand. Test specimens were prepared at Dr =80% of relative density and were subjected to three different normal stresses of 100, 200, and 300?kPa. The experimental results showed that the deposition mode (wet and dry) and the geotextile reinforcement have significant effects on the behavior of reinforced sand. The increase in shear strength is relatively more significant for specimens prepared with dry deposition mode as compared to those prepared with wet deposition mode and it increases with the number of geotextile layers, this effect becomes less significant for wet specimens. The experimental results also demonstrated that (PEC55) non-woven geotextile shows a better performance than the (S41) of geotextile. These results can be explained by the effective tensile strength property of polyester yarns of the (PEC55) non-woven geotextile that it has led to a significant increase in the shear strength.  相似文献   

2.
Two marine calcareous deposits as crushable soils and a siliceous sand as a noncrushable soil were used in this study to compare their monotonic response. Undrained monotonic triaxial tests were conducted on samples, which were prepared in different relative densities and consolidated under various confining pressures. The location of phase transformation point in undrained response of the sands in different initial conditions was evaluated. The effect of important parameters including relative density, confining pressure, particle shape, and particle breakage on phase transformation point was assessed. The input energy applied per unit volume of the soils was used to interpret the shearing response of crushable and noncrushable soils. The results showed that calcareous sands have more tendencies in contraction. Particle shape and breakage play a key role in engineering behavior of crushable soils.  相似文献   

3.
Abstract

Construction of the reefs in the South China Sea is a significant foundation to the secure stability and economic development of China. The construction of an airport runway is necessary for this realization. The calcareous sand is the main primary material in the runway construction. A certain type of calcareous sand near a certain reef of the South China Sea was studied in this paper. To investigate this specific calcareous sand, quartz sand was used as a reference for comparison. Microscopic 3-D imaging, compression and triaxial tests were conducted to test the micro, squeezing and shear properties. The effect mechanism of gradation on the calcareous sand’s compressibility and shear characteristics are discussed from a mesoscopic viewpoint using 3-D morphology. Calcareous sand particles are multiangular and flatter in comparison with quartz sand. The larger the particle sizes are, the more different the two sands’ morphologies are. The compressibility of calcareous sand is greater, and the effect of the coarse fraction (5–1?mm) content in the gradation plays the most significant role in this feature. When the coarse particles’ content is less than 25% and the mass ratio of the middle and fine particles (M) is constant, there is the worst coarse fraction content causing the calcareous sand to be most likely compressed. The worst coarse fraction content decreases with the increase in M, and an empirical formula is proposed. When the gradation, relative density and confining pressure are the same, the peak shear stress and strain of calcareous sand are all at a high level. The effect of confining pressure is manifested in calcareous sand. The shear strength and dilation of calcareous sand are also most affected by the medium coarse fraction (5–0.25?mm) content.  相似文献   

4.
The post-cyclic behavior of biogenic carbonate sand was evaluated using cyclic triaxial testing through a stress control method under different confining pressures between 50 to 600 kPa. The testing program included a series of isotropically and anisotropically consolidated, undrained triaxial compression and extension tests on samples of remolded calcareous Bushehr sand. Grading analyses (before and after each test) were used to examine the influence of particle breakage on post-cyclic behavior of Bushehr sand. The particle breakage commonly occurred in these soils even in lower values of confining pressure, yet there was not a clear correlation between the post-cyclic responses and particle breakage. Based on the present study, a concept is suggested for post-cyclic behavior of carbonate sand. It was observed that post-cyclic strength has a good correlation with cyclic stress ratio, type of consolidation, and value of residual cyclic strain. For all specimens, it is clear that the post-cyclic strength is greater than monotonic strength, irrespective of confining pressure and relative density.  相似文献   

5.
Abstract

In this article, the dilatancy of calcareous soil is studied systematically based on triaxial consolidation drainage shear tests, and the difference in dilatancy between calcareous soil and siliceous soil is also investigated. It was found that: ① Calcareous soil experience obvious dilated deformation. Dilatancy tendency increases with increasing related density and decreases with increasing confining pressure. ② The volumetric strain rate initially increases from negative to positive. After it reaches a maximum, there is a small decrease in the volumetric strain rate, but it is still greater than zero, and the stress-strain curves are of softening type. ③ For the same condition, the dilatancy deformation of calcareous sand begins later than that of siliceous sand, and the volume compression before dilatancy is also larger for calcareous sand. ④ The critical state alone cannot accurately describe the entire deformation process of soil, and it is proposed that the phase transformation state be added to the standard method used to assess soil dilatation and contraction. ⑤ Based on the statistical analysis of experimental data, mathematical relationships were established between void ratio, relative density, and effective confining pressure of phase transformation state and critical state, respectively.
  • Highlights

  • Reports results from a well-designed experiment that includes a good amount of samples and data.

  • Effects of relative density and effective confining pressure on deformation mode and mechanical properties of calcareous sand are evaluated.

  • The difference in dilatancy between calcareous sand and siliceous sand was compared

  • The phase-transformation state and critical state were compared with the axial strain, volumetric strain and deviatoric stress.

  • Using phase-transformation void ratio and critical void ratio to describe the whole deformation process of calcareous sand is proposed.

  • The mathematical expressions of phase-transformation void ratio and critical void ration were given, respectively.

  相似文献   

6.
A testing program was initiated to determine the stress-strain and strength behavior of two very different marine sands (a calcareous sediment from South Australia and a siliceous sediment from the United Kingdom) at elevated confining pressures. The testing matrix consisted of a series of isotropically consolidated, undrained (CIU) and drained (CID), triaxial compression tests on samples of naturally deposited calcareous and siliceous sediment and remolded calcareous sediment. It was found that the calcareous samples displayed little cemented behavior during shear. For tests conducted at pressures up to 1.5 MPa, a significant amount of particle crushing occurred in the calcareous samples but not in the siliceous samples. Particle degradation and reorientation facilitates transitions from dilative to contractive behavior with increases in confining stress. The calcareous sediment exhibited contractive behavior at confining pressures above approximately 500 kPa and the siliceous sediment remained dilative at stresses up to 1 MPa during undrained loading. Comparison with data collected by the University of Sydney (CID tests with confining pressures up to 60 MPa) showed that most of the variations in strength behavior occurred within the low stress range (up to 2 MPa) tests conducted at URI. This was evident in the friction angle data and in the reloading Young's modulus data.  相似文献   

7.
ABSTRACT

The behavior of loose anisotropically consolidated calcareous sand obtained from an island in the South China Sea was investigated under undrained monotonic and cyclic loading in a hollow cylinder torsional apparatus. The tests were conducted on specimens which consolidated under various initial effective confining pressures and consolidation stress ratios. The monotonic test results show that the failure and phase transformation line are essentially independent of the consolidation conditions, while the initial contractive tendency of the specimens decreases with an increasing consolidation stress ratio. During monotonic loading of the anisotropically consolidated specimens, a same major principal stress direction is observed at the constant stress ratio lines up to the phase transformation line, irrespective of initial effective confining pressure. The cyclic strength of the sand increases with an increasing consolidation stress ratio. Moreover, a pronounced stress dependence is observed in the sand with higher consolidation stress ratio. During cyclic loading, the generated excess pore water pressure presents considerable fluctuations. The normalized terminal excess pore water pressure is described as a function of consolidation stress ratio. The tests show that the particle shape, rather than particle crushing, plays an important role in the monotonic and cyclic behaviors of the calcareous sand.  相似文献   

8.
ABSTRACT

One-way cyclic loading is more typical for traffic loading and cyclic triaxial test has been recognized as a useful method for solving many engineering problems. Under traffic loading, the influence of variable confining pressure on cyclic behavior of natural organic clay subjected to cyclic traffic loading is rarely reported in the literature. In this study, a laboratory investigation on undrained cyclic behavior of natural organic clay is presented and conducted by cyclic triaxial apparatus. Tests are conducted by both constant confining pressure and variable confining pressure, to simulate the loading conditions induced by passing vehicles in actual engineering. Different stress levels are also considered in this study. By comparing between the results of constant confining pressure tests and variable confining pressure tests, it shows that the one-way cyclic behavior of organic clay is influenced significantly by variation of confining pressure, in terms of pore water pressure, permanent axial strain and stress–strain hysteretic loops.  相似文献   

9.
Abstract

The study of the unsaturated soils is a very complex field to which several researches in laboratory and on site are directed these last years. An experimental study aims to quantify the influence of the Skempton coefficient B characterizing the degree of saturation on the behavior of the granular sand to the liquefaction resistance of sand. The study is based on undrained triaxial tests performed on natural Chlef sand carried out at an initial relative density Dr = 50% under a confining pressure of 50, 100 and 200?kPa for Skempton coefficient B?=?10 to 92%. The results of the tests show that an increase of confining pressure leads to an increase of the shear stress of the samples. For the lower value of the degree of saturation results of our findings indicate an increase of the resistance to liquefaction; our results are in good agreement with others observed in several research projects conducted with other sands. The increase of Skempton coefficient B induces an increase of pore water pressure and a decrease of the shear strength. The pore pressure (u) increases with an exponential manner with the increase of the degree of saturation; while the residual shear strength (Rs) decreases with logarithmic manner with the increase of degree of saturation (B).  相似文献   

10.
This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density Dr = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (Fc), inter-granular void ratio (eg), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (qpeak) and the logarithm of the saturated hydraulic conductivity (ksat) for all confining pressures.  相似文献   

11.
Abstract

This article presents the performance of the short-term bearing capacity on soft clay soil treated by Kenaf geotextile under vertical loading via a small-scale modelling test at unit gravity. The ground model was formulated by consolidating kaolin in a rigid testing compartment. In the loading test, the strip footing was represented by a rigid footing. For the treated case, a series of tests were performed to examine the effects of the burial depth of the Kenaf geotextile on the bearing capacity of the soft soil. The Kenaf geotextile was laid beneath the rigid footing (at the ground surface) and at 50, 75 and 100?mm depth from the soil surface. All the measured results of the Kenaf geotextile treated ground were compared with the untreated ground. The incorporation of Kenaf fibre geotextile was observed to enhance the bearing capacity of soft cohesive clay up to 281% depending upon the depth of the installed geotextile. The geotextile at the surface provided the highest bearing capacity and sustained the highest displacement at failure. The outcome of this research will promote the use of natural fibre geotextiles as sustainable earth reinforcement in temporary earthwork applications.  相似文献   

12.
Abstract

The mechanical characteristics of calcareous silt interlayers play an important role in the stability of island-reef foundations. Direct shear and consolidation tests were performed to study the relationship between the mechanical properties and the physical parameters of calcareous silt. Based on the consolidation test results and analysis of the settling examples, different calculation methods for soil settling were compared. The results show the following. (1) The relationship between the cohesion and water content of calcareous silt can be represented by an M-shaped curve. The water contents corresponding to the two peaks of the M-type curve increase with increasing dry density. (2) When the dry density is less than 1.33?g/cm3, increasing the density significantly improves the internal friction angle of calcareous silts. When the dry density of the calcareous silt is greater than 1.33?g/cm3, the internal friction angle is affected by both the dry density and the water content. (3) The shear strength decreases when the water content exceeds the optimum level. (4) The compressive modulus of calcareous silt is larger than that of terrigenous silt. Specifically, it decreases with decreasing dry density and increasing water content. (5) The stepwise loading method should be used to estimate the soil settling before fill engineering construction.  相似文献   

13.
Abstract

This article presents an experimental investigation on the dynamic consolidation (DC) drainage behavior of soft marine clays. A sinusoidal harmonic load with different frequencies was applied to simulate the DC method in which the conventional impact load was replaced by the cyclic load. Four geotextile-filter strips were used to form the side drainage channels simulating the wick drain method. A series of loading tests were conducted on soft soil specimens at different confining pressures (i.e., 20, 40, 70, and 100?kPa) and different vibration frequencies (i.e., 0, 0.5, 1, 1.5, 2, and 5?Hz). Test results showed that both confining pressure and frequency have significant influences on the drainage behavior of soft marine clay specimens. The magnitude of drainage volume consistently decreases linearly with increasing confining pressure. Compared to static loading condition, specimens under cyclic loading condition at different frequencies show a better drainage performance. Specimen at applied frequency of 1?Hz exhibits the maximum cumulative drainage volume due to the resonant effect.  相似文献   

14.
ABSTRACT

Oil and its derivatives contaminate many soils and not only affect their chemical and biological properties but also their geotechnical properties. As oil contamination may deteriorate the functioning of piles, this paper addresses the effects of oil contamination on soil–pile interactions. Axial compressive bearing capacities of two close-ended, instrumented piles were investigated in different oil-contaminated sand using frustum confining vessel. Three different oils (gasoil, crude oil, and used motor oil) at different contamination levels were considered and using some strain gauges, the toe, shaft, and the net total bearing capacity of piles, as well as load distributions along the pile length, were derived. The results show that the presence of oil between soil particles has considerable adverse effects on bearing capacities of model piles, especially the shaft bearing capacity. The oil viscosity and percentage, as well as the contaminated sand bed thickness around the piles, are the most influential parameters. The higher the oil viscosity and oil content, the lower the values of the piles’ bearing capacities in comparison to the uncontaminated sand. With some modifications on the bearing capacity parameters of CFEM method, a good agreement was observed between measured and calculated bearing capacity values.  相似文献   

15.
In Memoriam     
Abstract

The engineering properties of deep continental margin sediments were determined on a worldwide basis. Deep Sea Drilling Project (DSDP) core data and material were utilized from over 900 cores obtained from 89 sites, primarily on the continental margins. Cores were recovered from penetrations to 200 m in water depths averaging 3000 m. Supplementary laboratory testing on selected cores was directed toward determining index properties and shear strength properties of the sediments. The study included a literature review of deep‐sea soil properties, the results of which are to be used by DSDP to evaluate foundation conditions for reentry cones with long casing strings. The results will also be used for a feasibility study of an ultradeepwater marine riser and well‐control system. The marine sediments examined can be divided into three main types: clay, calcareous ooze, and siliceous ooze. Sediment distribution consisted of 48% calcareous ooze, 43% clay, 6% siliceous ooze, and 3% volcanic ash. Because of the sample disturbance inherent in the deepwater coring operation, emphasis was placed on analyzing sediment properties not significantly affected by changes in in situ stresses and structure caused by sampling. Averages and ranges in values of water content and unit weight are presented for the three main sediment types. Plasticity and strength characteristics are discussed in detail and the elastic and compression properties are outlined. The geotechnical properties of deep continental margin soils are summarized.  相似文献   

16.
Abstract

Hollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand.  相似文献   

17.
In this paper, a comprehensive study on simulating the shearing behavior of frictional materials is performed. A set of two explicit equations, describing the relationship among the shear stress ratio and the distortional strain and the volumetric strain, are formulated independently. The equations contain three stress parameters and three strain parameters and another parameter representing the nonuniformity of stress and strain during softening. All the parameters have clear physical significance and can be determined experimentally. It is demonstrated that the proposed equations have the capacity of simulating the complicated shearing behavior of many types of frictional materials including geomaterials. The proposed equations are used to simulate the stress–strain behavior for 27 frictional materials with 98 tests. These materials include soft and stiff clays in both reconstituted and structured states, silicon sands and calcareous sands, silts, compacted fill materials, volcanic soils, decomposed granite soils, cemented soils (both artificially and naturally cemented), partially saturated soils, ballast, rocks, reinforced soils, tire chips, sugar, wheat, and rapeseed. It has been demonstrated that the proposed explicit constitutive equations have the capacity to capture accurately the shearing behavior of frictional materials both qualitatively and quantitatively. A study on model parameters has been performed.  相似文献   

18.
Abstract

This paper presents the results of a laboratory investigation undertaken to study the nature of two submarine carbonate soils from Bombay High off the west coast of India, as well as to study the shear and plasticity behavior of their sand and silt‐clay fractions, respectively. Scanning electron micrographs reveal that the carbonate content in both soils is comprised primarily of nonskeletal particles of various types. X‐ray diffraction and infrared absorption analyses indicate that in one soil the carbonate fraction consists of calcite and aragonite minerals, whereas in the other soil dolomite is also present. The non‐carbonate fraction of both soils is comprised primarily of quartz and feldspar, and also some clay minerals. The nature of the carbonate fraction of the two soils indicates that they were formed by different depositional processes.

During drained triaxial shear the nonskeletal sand grains of both soils exhibit a lower degree of crushing when compared with that of the skeletal carbonate sands, and thus appear to be stronger foundation material.

Although the carbonate contents of the silt‐clay fractions of the two soils are similar, they exhibit markedly different plasticity characteristics . This is probably because of the microlevel cementation produced by carbonate material in one soil.

This study leads one to the conclusion that carbonate content alone should not be treated as a parameter which controls the engineering behavior of submarine soils; the nature and form of carbonate material must also be identified.  相似文献   

19.
Abstract

This article presents a study of liquefaction resistance behaviour of sand using a cyclic triaxial test. The site investigation was performed, and frozen undisturbed specimens were taken from the Izumio site in Osaka, Japan. According to the evidence in 1995 Kobe Earthquake, the first two sand layers are vulnerable to undergo liquefaction. The effect of deviatoric stress on liquefaction resistance was focused on in this study. The excess pore pressure ratio, hysteresis loop, and effective stress path from the cyclic triaxial tests were reported. A multispring element model was employed to simulate the soil behaviour under cyclic loading. The results showed that applied deviatoric stress could influence the liquefaction resistance of sandy soil samples. The plots of the cyclic stress ratio versus the number of cycles to generate liquefaction known as a liquefaction resistance curve can be then constructed and compared with other sands.  相似文献   

20.
The liquefaction resistance of the soils used to be estimated through the in situ tests, such as standard penetration test and cone penetration test; or by means of cyclic triaxial test in laboratory. However, both in situ tests and cyclic triaxial test are time-consuming and costly; this study introduces a quick and cost-effective method to evaluate the liquefaction resistance of soils under certain confining pressure in laboratory. A particular device modified from the conventional triaxial compression test apparatus, namely “Triaxial Cone Penetration Test”, was developed to obtain the peak values of cone resistance in soils so as to correlate the liquefaction resistance of the reclaimed soils evaluated by cyclic triaxial tests. The test result indicates a good correlation between the peak value of cone resistance and the corresponding cyclic stress ratio (CSR) at the state of initial liquefaction, in which the correlation for loose samples is better than that for dense samples. Besides, both peak values of cone resistance and corresponding CSR increase with fine content of soils reaches 10% and decreased with fine content varying between 10% and 50%. By examining the compositions of the soils with scanning electron microscopy and X-ray diffraction, it is found that the proportion and characteristics of the fines plays an important role on the liquefaction resistance of the reclaimed soils.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号