共查询到20条相似文献，搜索用时 15 毫秒
1.
伪距多路径误差是影响GNSS导航定位精度的主要误差源之一。多路径误差与接收机周围环境有关,在实际应用中难以建立有效的多路径误差模型进行改正。对于多频GNSS接收机可以通过多频观测值组合估计伪距多路径,但该方法不适用于价格低廉的单频接收机,而导航中使用的大多数为单频接收机。因此,开展单频GNSS伪距多路径误差提取研究具有重要的工程应用价值。本文基于小波分析对单频GNSS接收机伪距多路径误差估计开展研究,首先验证了小波分析用于单频GNSS伪距多路径误差估计的可行性;其次,研究了采用不同的小波基和分解层次对多路径误差估计的影响;最后,研究了改正多路径误差对GNSS定位的影响。实验结果表明不同的小波基和分解层次对多路径误差提取效果没有明显的差别,但小波分解层次较低时定位误差分布相对更加集中,同时,经过多路径误差改正后在NEU3个方向RMS平均改善率达到20.4%、25.1%、16.4%。 相似文献
2.
Multipath remains one of the major challenges in Global Navigation Satellite System (GNSS) positioning because it is considered the dominant source of ranging errors, which can be classified into specular and diffuse types. We present a new method using wavelets to extract the pseudorange multipath in the time domain and breaking it down into the two components. The main idea is an analysis-reconstruction approach based on application of both continuous wavelet transform (CWT) and discrete wavelet transform (DWT). The proposed procedure involves the use of L1 code-minus-carrier (CMC) observable where higher-frequency terms are isolated as residuals. CMC residuals are analyzed by applying the CWT, and we propose the scalogram as a technique for discerning time–frequency variations of the multipath signal. Unlike Fourier transform, the potential of the CWT scalogram for examining the non-stationary and multifrequency nature of the multipath is confirmed as it simultaneously allows fine detection and time localization of the most representative frequencies of the signal. This interpretation of the CWT scalogram is relevant when choosing the levels of reconstruction with DWT, allowing accurate time domain extraction of both the specular and diffuse multipath. The performance and robustness of the method and its boundary applicability are assessed. The experiment was carried out using a receiver of Campania GNSS Network. The results are given in which specular multipath error is achieved using DWT level 7 approximation component and diffuse multipath error is achieved using DWT level 6 denoised detail component. 相似文献
3.
通过载噪比(CNR)、数据完整率、伪距与载波相位观测值噪声和伪距多路径效应四个指标对北斗三号卫星导航系统(BDS-3)新频点B1C/B2a车载动态数据的特性进行了分析,测试了BDS-3新频点动态精密单点定位(PPP)的性能,并与其它全球卫星导航系统(GNSS)进行了对比.试验结果表明,BDS-3新频点B2a平均CNR优于北斗卫星导航系统(BDS)其它频率,但略差于GPS L5;相较于其它GNSS,BDS数据完整率相对较高,其中BDS-3 B2a新频点数据完整率最高;BDS-3 B2b伪距观测值噪声最小,B1C和B2a伪距观测值噪声约为B2b信号的3倍,但不同频率相位观测值噪声处于同一量级;对于伪距多路径而言,BDS-3 B1C/B2a信号略小于B2b信号.总体而言,GPS L5信号抑制多路径效应的能力最强.在动态PPP性能方面,BDS-3 B1C/B2a双频组合动态PPP定位精度最优,其三维(3D)均方根(RMS)误差为0.439 m,相比BDS B1I/B3I、GPS L1/L2、 GLONASS G1/G2和Galileo E1/E5a双频组合PPP,其精度改善率分别为49%、 5... 相似文献
4.
Though state-of-the-art dual-frequency receivers are employed in the continuous Global Positioning System (CGPS) arrays, the
CGPS coordinate time series are typically very noisy due to the effects of atmospheric biases, multipath, receiver noise,
and so on, with multipath generally being considered the major noise contributor. An adaptive finite-duration impulse response
filter, based on a least-mean-square algorithm, has been developed to derive a relatively noise-free time series from the
CGPS results. Furthermore, this algorithm is suitable for real-time applications.
Numerical simulation studies indicate that the adaptive filters is a powerful signal decomposer, which can significantly mitigate
multipath effects. By applying the filter to both pseudorange and carrier phase multipath sequences derived from some experimental
GPS data, multipath models have been reliably derived. It is found that the best multipath mitigation strategy is forward
filtering using data on two adjacent days, which reduces the standard deviations of the pseudorange multipath time series
to about one fourth its magnitude before correction and to about half in the case of carrier phase. The filter has been successfully
applied to the pseudorange multipath sequences derived from CGPS data. The benefit of this techniques is that the affected
observable sequences can be corrected, and then these corrected observables can be used to improve the quality of the GPS
coordinate results. ? 2000 John Wiley & Sons, Inc. 相似文献
5.
Wavelet packets based denoising method for measurement domain repeat-time multipath filtering in GPS static high-precision positioning 总被引：1，自引：1，他引：0
Lawrence Lau 《GPS Solutions》2017,21(2):461-474
Repeatable satellite orbits can be used for multipath mitigation in GPS-based deformation monitoring and other high-precision GPS applications that involve continuous observation with static antennas. Multipath signals at a static station repeat when the GPS constellation repeats given the same site environment. Repeat-time multipath filtering techniques need noise reduction methods to remove the white noise in carrier phase measurement residuals in order to retrieve the carrier phase multipath corrections for the next day. We propose a generic and robust three-level wavelet packets based denoising method for repeat-time-based carrier phase multipath filtering in relative positioning; the method does not need tuning to work with different data sets. The proposed denoising method is tested rigorously and compared with two other denoising methods. Three rooftop data sets collected at the University of Nottingham Ningbo China and two data sets collected at three Southern California Integrated GPS Network high-rate stations are used in the performance assessment. Test results of the wavelet packets denoising method are compared with the results of the resistor–capacitor (RC) low-pass filter and the single-level discrete wavelet transform (DWT) denoising method. Multipath mitigation efficiency in carrier phase measurement domain is shown by spectrum analysis of two selected satellites in two data sets. The positioning performance of the repeat-time-based multipath filtering techniques is assessed. The results show that the performance of the three noise reduction techniques is about 1–46 % improvement on positioning accuracy when compared with no multipath filtering. The statistical results show that the wavelet packets based denoising method is always better than the RC filter by 2–4 %, and better than the DWT method by 6–15 %. These results suggest that the proposed wavelet packets based denoising method is better than both the DWT method and the relatively simple RC low-pass filter for noise reduction in multipath filtering. However, the wavelet packets based denoising method is not significantly better than the RC filter. 相似文献
6.
Multipath mitigation via component analysis methods for GPS dynamic deformation monitoring 总被引：1，自引：0，他引：1
Multipath is one of the main error sources in high-precision global positioning system (GPS) dynamic deformation monitoring, as it is difficult to be mitigated by differencing between observations. In addition, since a specific frequency threshold value between multipath and deformation signals may not exist, multipath is usually inseparable from the low-frequency vibration signal using conventional frequency-domain filter methods. However, the multipath repeats in two sidereal days when the surroundings of a GPS antenna remain unchanged. This characteristic can be exploited to model and thus mitigate multipath effectively in dynamic deformation monitoring. Unfortunately, a major issue is that the degree of repeatability decreases as the interval between first day and subsequent days increases. To overcome this problem, we develop a new sidereal filtering referred to as reference EMD-ICA (EMD-ICA-R), where empirical mode decomposition (EMD) and independent component analysis (ICA) are jointly used to model multipath and renew the reference multipath. For the successful implementation of the EMD-ICA-R, an a priori denoised multipath signal is needed as a reference. We further propose to use the principal component analysis (PCA) method to extract more accurate reference multipath signal and form a combined PCA-EMD-ICA-R approach. Simulation experiments with a motion simulation platform were conducted, and the testing results indicate that the proposed methods can mitigate the multipath by around 67 % when a reliable reference multipath signal is extracted from a static situation. Furthermore, simulation experiments with different deformation signals added into the coordinate time series of three consecutive days show that the two proposed methods are also effective in a dynamic situation. Since wavelet filtering is used to denoise the reference multipath signals in the new approaches, simulation experiments with several wavelet filters are tested, and the results indicate that the PCA-EMD-ICA-R approach can work well with various wavelet filters. 相似文献
7.
8.
广域差分参考站两种伪距平滑算法的再评估 总被引：4，自引：0，他引：4
广域差分GPS系统（WADGPS）参考站上，需要利用载波相位平滑伪距算法来减小多路径效应的影响。伪距平滑算法有Hatch滤波和加权Hatch滤波两种。文中基于我国WADGPS参考站的实际数据，对这两种平滑算法进行重新评估。实际数据显示，如果不能获得可靠的伪距观测值的方差，在抑制伪距中噪声的影响方面，Hatch滤波明显优于加权Hatch滤波。 相似文献
9.
陆基增强系统(GBAS)是利用载波相位平滑伪距差分修正实现对导航辅助定位的. 其中,平滑时间常数是影响载波相位平滑伪距精度的关键参数. 本文分析研究了不同平滑时间下电离层时间梯度和空间梯度对Hatch滤波的影响. 在结合电离层时空梯度和多径效应引起的滤波总误差方差的基础上,推导出自适应的最优平滑时间常数. 分别对GBAS静态和动态两种环境下的定位误差进行实验,实验结果表明,采用本文推导出的自适应平滑时间常数降低了GBAS伪距测量误差,从而使定位精度得到增强. 相似文献
10.
A new method to mitigate multipath error in single-frequency GPS receiver with wavelet transform 总被引：2，自引：1，他引：1
One of the major errors in high-precision GPS positioning is multipath. Multipath effect modeling and reduction have been a challenging issue in high-accuracy GPS positioning applications due to its special properties. Different methods have been employed to mitigate this error including hardware and software approaches. We reduce C/A code multipath error by adopting an efficient software method which uses wavelet transform as a basic data processing trend. The key idea of the proposed method is using stationary wavelet transform (SWT) in GPS signal data processing. Since we have used SWT, there is complete access to high-frequency and low-frequency terms in both time and frequency domains, and we can apply appropriated procedures to mitigate this error. The multipath error mostly is a low-frequency term. In our proposed method, the double difference (DD) residuals are applied to the SWT to identify the multipath disturbance. The extracted multipath is then used to correct DD observations. Our experiments include three data sets to investigate the proposed method and compare it with existing algorithms. We used simulations for two of these data sets. The results indicate the efficiency of the proposed method over existing algorithms. 相似文献
11.
目前,北斗全球卫星导航系统有5颗试验卫星发射试验信号。试验卫星数据质量分析是北斗全球系统信号体制验证的重要内容。基于单测站北斗试验卫星观测数据,采用伪距相位差组合和伪距多径组合方法,初步分析了试验卫星民用信号以及Bs频点信号伪距测量噪声和多径误差。结果表明,倾斜同步轨道卫星伪距测量精度优于中轨道卫星;在各导航信号中,B2a+b信号伪距测量精度最高,具有最优的抗多径性能;B1C信号伪距测量精度最低,抗多径性能最差;Bs信号伪距测量精度较差,但优于B1C信号,且其伪距多径存在一个与高度角相关的系统误差,在高度角最大时可达0.5 m。 相似文献
12.
13.
Much of the research into multipath detection and mitigation has not considered the carrier phase delay between the line of
sight (LOS) and reflected signals. A new variable referred to as early late phase (ELP) has recently been proposed to exploit
this phase difference. It has been found that in a receiver tracking the L1 GPS signal, the probability of detecting multipath
is lower when the carrier phase difference between the LOS and a reflected signal is an integer multiple of π. Since the pseudorange
error caused by the multipath’s presence is the highest in this case, we propose to exploit the coexistence of another GPS
civilian signal, the L2C. We present an analysis of ELP for the L1 and L2C signals, and a combination of both, for detecting
multipath. The multipath detection performance has been compared using probabilities of false alarm and detection. An ideal
algorithm should have lower probability of false alarm and higher probability of detection. However, it has been found that
using dual-frequency ELP increases both probabilities. Thus, receiver operator characteristics (ROC) curves, and the area
under the ROC curves, have been used for effective comparison. It has been found that the L2C signal individually gives worse
performance than L1 because of its weaker signal strength. However, the combination of L1 and L2C gives the best overall performance,
and thus it can be claimed that ELP using dual-frequency receivers is a more effective approach for detecting multipath. 相似文献
14.
A preliminary study was conducted to evaluate the amount of pseudorange multipath at 390+ sites in the National Continuously Operating Reference Station (CORS) Network. The National CORS Network is a cooperative effort involving over 110 different agencies, universities, and private companies who seek to make GPS data from dual-frequency receivers located throughout the United States and its territories available to the general public. For CORS users, pseudorange multipath can seriously degrade the accuracy of any application that relies on precise measurements of the pseudorange observable over a short period of time, including differential pseudorange navigation, kinematic and rapid-static surveying, and ionospheric monitoring. The main objectives of this study were to identify the most affected and least affected sites in the network, to closely investigate problematic sites, and to compare various receiver/antenna combinations. Dual-frequency carrier phase and pseudorange measurements were used to estimate the amount of L1 and L2 pseudorange multipath at each site over a one-year period. Some of the most severely affected sites were maritime Differential GPS and Nationwide Differential GPS (DGPS/NDGPS) sites. Photographs obtained for these sites verified the presence of transmission towers and other reflectors in close proximity to the GPS antennas. Plotting the variations of the L1 and L2 pseudorange multipath with respect to azimuth and elevation further verified that even above a 60° elevation angle there was still as much as five meters of pseudorange multipath at some sites. The least affected sites were the state networks installed in Ohio and Michigan; these sites used excellent antenna mounts, choke ring antennas, and new receiver technology. A comparison of the 12 most commonly used receiver/antenna combinations in the CORS Network indicated that newer receivers such as the Ashtech UZ-12, Leica RS-500, and Trimble 5700 help to significantly mitigate pseudorange multipath, while the receivers/antennas at some DGPS/NDGPS sites, and the antennas formerly used at the Wide Area Augmentation System (WAAS) sites, are among those most affected by pseudorange multipath. The receiver/antenna comparison did not take into account the potential presence of reflectors at the sites (i.e., it is possible that a well-performing receiver/antenna combination could have been consistently placed at very poor site locations, and vice-versa).Product Disclaimer: Mention of a commercial company or product does not constitute an endorsement by the National Oceanic and Atmospheric Administration. Use for publicity or advertisement purposes of information from this paper concerning proprietary products or the comparison of such products is not authorized. 相似文献
15.
16.
本文针对智能手机内部天线构造、GNSS接收芯片等因素限制,手机原始观测值易受外部环境影响,观测噪声大,导致定位精度较差的问题,面向大众导航定位需求,以提高手机伪距单点定位精度为目标,在对手机载波观测值周跳探测的基础上,研究对比分析了基于载波、多普勒平滑下的伪距单点定位的性能。试验表明：载波平滑伪距和多普勒平滑伪距都可以有效提高定位精度,但多普勒平滑伪距具有更好的稳定性且定位精度更好,统计显示在东（E）、北（N）、高（U）3个方向的均方根值（RMS）分别提高了52%、62%、60%,平面精度优于1.5 m。 相似文献
17.
针对Android手机GNSS伪距定位精度较低的问题,利用手机端观测信息,通过载波相位/多普勒平滑伪距改善手机端伪距观测值的质量,从而达到提高定位精度的效果。首先给出了Android手机GNSS原始观测量的获取方法,然后推导了载波相位平滑伪距和多普勒平滑伪距算法模型,并设计合理有效的试验对算法的精度进行评定。试验结果表明：在手机端静态定位中载波相位和多普勒平滑算法均可提高原始伪距的定位精度,且多普勒平滑算法表现更优;在手机端动态定位中多普勒平滑算法可获得比原始伪距更优的定位精度,但是载波相位平滑算法较原始伪距更差;由于硬件的制约手机端周跳和信号失锁严重,占比超过50%,载波相位在手机端的可用性较低;多普勒平滑算法的最优平滑时间常数小于等于10 s,具有实时动态定位的巨大潜力。 相似文献
18.
利用各频率观测值间物理上的相关性,采用数学变换得到一个含有双频原始载波观测信息的虚拟观测值,与双频数据按长波长特性进行多频组合来放大周跳。对探测出的周跳候选值利用Melbourne-Wubbena组合及多项式拟合作为两个判别条件来进行甄选,达到了实时修复双频原始载波相位观测值周跳的目的。 相似文献
19.
20.
基于IGS的L2C信号跟踪站数据验证了具有L2C码的卫星的L2载波的信噪比高于没有L2C码的卫星的L2载波的信噪比,L2载波恢复的数据质量更好.针对不同的接收机,对比分析了C/A码和L2C码多路径效应及观测噪声水平,发现对TRIMBLE NETRS接收机,L2C码误差水平明显高于C/A码,与期望结果相反. 相似文献