共查询到20条相似文献，搜索用时 31 毫秒
1.
Tension-Only Concentrically Braced Frames (TOCBF) exhibit deteriorating pinched hysteretic behaviour during strong earthquakes. Slender braces transit between an elastic buckling state, a restraightening state, in which they carry almost no load, an elastic tensile loading state as they are suddenly taut and, finally, a tensile yielding state. It has long been suspected that the sudden increase in tensile forces in the braces of TOCBSF creates detrimental impact loading on the connections and other structural elements. No experimental evidence, however, has been provided so far to confirm, or to quantify, this impact phenomenon. This paper addresses this issue through shake table tests of half scale, two-storey, TOCBF models. By normalizing the hysteresis loops of braces obtained from shake table tests to the yield strength of steel obtained from quasi-static tests, the increase in tensile forces in the braces was obtained. Results of dynamic tensile tests on steel coupons under similar strain rates as observed during the shake table tests showed that this increase in tensile forces is not the result of impact, but is rather caused by a yield strength increase of the steel under high strain rate. A procedure is proposed to estimate and account for this increase in tensile forces in the braces at the design stage. 相似文献
2.
3.
Hossein Mohammadi Vahab Toufigh Ali Akbar Golafshani Ali Arzeytoon 《Bulletin of Earthquake Engineering》2018,16(2):731-752
In this paper, an innovative seismic lateral force resisting system for tall buildings is introduced. In this system, a novel supplemental part, ribbed bracing system (RBSyst), is attached to Braced Tube System, creating a modified BTS. RBSyst is a supplemental part which is attached to the conventional bracing members to eliminate buckling problem. The behavior of RBSyst under tensile force is similar to that of the conventional braces. However, in compression, it prevents the braces from buckling by length reduction. In order to evaluate the efficiency of this new BTS system by performance-based assessment, two typical 40-story tall buildings with different story modules equipped with this proposed bracing system are modeled numerically. Then, the seismic behavior of these 3-dimensional models are evaluated by nonlinear time history analysis under maximum considered earthquakes and service-level earthquakes. The results of the analysis demonstrate that the performance of the tall buildings equipped with this new BTS system is within the acceptable limits under both service-level and maximum considered earthquake ground motions. Additionally, it is shown that RBSyst part can effectively enhance the seismic behavior of BTS systems. 相似文献
4.
An analytical and experimental study has been conducted to evaluate the seismic performance of a three‐story suspended zipper steel frame. The frame was concentrically braced and had zipper struts to transfer the unbalanced forces induced on the beams due to the buckling of the lower‐story braces. The experimental study was conducted with the hybrid test technique, in which only the bottom‐story braces of the three‐story frame were physically tested, while the behavior of the rest of the frame was modeled using a general structural analysis software. The paper discusses issues pertinent to the calibration of the computer model for the analytical substructure as well as for the entire frame, including the selection of an appropriate damping matrix, and the modeling of the buckling behavior of the braces and bracing connections. The analytical model of the entire frame was validated with the hybrid tests and was able to accurately capture the material and geometric nonlinearities that developed when the braces yielded and buckled. This study has demonstrated the usefulness of hybrid testing in improving analytical models and modeling assumptions and providing information that cannot be obtained from an analytical study alone. The results have shown that the suspended zipper frame can distribute the brace nonlinearity over the first two stories as intended in the design and will not have catastrophic failure under the design‐level earthquakes considered in this study, despite the significant inelastic deformations. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
5.
The concentrically braced frame (CBF) structure is one of the most efficient steel structural systems to resist earthquakes. This system can dissipate energy during earthquakes through braces, which are expected to yield in tension and buckle in compression, while all other elements such as columns, beams and connections are expected to behave elastically. In this paper, the performance of single‐storey CBFs is assessed with nonlinear time‐history analysis, where a robust numerical model that simulates the behaviour of shake table tests is developed. The numerical model of the brace element used in the analysis was calibrated using data measured in physical tests on brace members subjected to cyclic loading. The model is then validated by comparing predictions from nonlinear time‐history analysis to measured performance of brace members in full scale shake table tests. Furthermore, the sensitivity of the performance of the CBF to different earthquake ground motions is investigated by subjecting the CBF to eight ground motions that have been scaled to have similar displacement response spectra. The comparative assessments presented in this work indicate that these developed numerical models can accurately capture the salient features related to the seismic behaviour of CBFs. A good agreement is found between the performance of the numerical and physical models in terms of maximum displacement, base shear force, energy dissipated and the equivalent viscous damping. The energy dissipated and, more particular, the equivalent viscous damping, are important parameters required when developing an accurate displacement‐based design methodology for CBFs subjected to earthquake loading. In this study, a relatively good prediction of the equivalent viscous damping is obtained from the numerical model when compared with data measured during the shake table tests. However, it was found that already established equations to determine the equivalent viscous damping of CBFs may give closer values to those obtained from the physical tests. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
6.
Seismic performance improvement of Special Truss Moment Frames using damage and energy concepts 
下载免费PDF全文
下载免费PDF全文 Nowadays, one of the most important methodologies to reduce the destructive effects of severe earthquakes on structures is the use of energy dissipation devices (EDDs). In this paper, a new configuration of special truss moment frame (STMF) systems including EDDs is theoretically proposed to improve their seismic performance. Such an improvement is achieved by provision of bending performance in these frames. For this purpose, the devices called buckling resistant braces (BRBs) are located at the side of beam‐column connections as the top and bottom members of truss‐girders. In this context, a five‐bay nine‐story STMF is designed using the damage and energy concepts recently proposed in the literature. To show the effectiveness of the proposed system with respect to the similar recently presented STMFs, this frame is then subjected to non‐linear static and non‐linear time‐history analyses under several ground motion records in order to survey on its seismic performance. Subsequently, such engineering demand parameters as lateral displacement, inter‐story drift ratio, overturning moment and shearing forces of stories, residual deformations and maximum time‐history displacement at roof level, as well as the process of plastic hinges formation are investigated. The results show the effectiveness of proposed configuration of EDDs used to improve the seismic safety of STMFs. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
7.
防屈曲支撑的工作机理及稳定性设计方法 总被引：4，自引：0，他引：4
防屈曲支撑(BRBs)是一种兼具普通支撑和金属耗能阻尼器双重功能的新型支撑形式。虽然其概念简单明确,但是工作机理却较为复杂,而目前人们对此类支撑的本质工作机理还没有得到充分的认识,因此很难提出较为全面合理的构件稳定性设计方法。本文对防屈曲支撑的工作机理进行了剖析,比较了目前已有的构件整体稳定性设计方法并指出了其中存在的问题,进一步提出应重点考虑间隙、边界条件以及摩擦力等因素的"强度-刚度"整体稳定设计方法的观点;从理论上推导了支撑内芯屈服段与约束构件之间的局部挤压力计算公式,揭示了支撑构件局部失稳破坏的机理,并进一步提出应重点考虑内芯板件宽厚比、间隙以及局部约束条件三者相关关系的支撑构件局部稳定设计方法的观点。 相似文献
8.
Given their excellent self‐centering and energy‐dissipating capabilities, superelastic shape memory alloys (SMAs) become an emerging structural material in the field of earthquake engineering. This paper presents experimental and numerical studies on a scaled self‐centering steel frame with novel SMA braces (SMAB), which utilize superelastic Ni–Ti wires. The braces were fabricated and cyclically characterized before their installation in a two‐story one‐bay steel frame. The equivalent viscous damping ratio and ‘post‐yield’ stiffness ratio of the tested braces are around 5% and 0.15, respectively. In particular, the frame was seismically designed with nearly all pin connections, including the pinned column bases. To assess the seismic performance of the SMA braced frame (SMABF), a series of shake table tests were conducted, in which the SMABF was subjected to ground motions with incremental seismic intensity levels. No repair or replacement of structural members was performed during the entire series of tests. Experimental results showed that the SMAB could withstand several strong earthquakes with very limited capacity degradation. Thanks to the self‐centering capacity and pin‐connection design, the steel frame was subjected to limited damage and zero residual deformation even if the peak interstory drift ratio exceeded 2%. Good agreement was found between the experimental results and numerical simulations. The current study validates the prospect of using SMAB as a standalone seismic‐resisting component in critical building structures when high seismic performance or earthquake resilience is desirable under moderate and strong earthquakes. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
9.
The test results described in Part 1 of this paper (Lee and Bruneau, 2008) on twelve steel built-up laced members(BLMs) subjected to quasi-static loading are analyzed to provide better knowledge on their seismic behavior. Strengthcapacity of the BLM specimens is correlated with the strength predicted by the AISC LRFD Specifications. Assessmentsof hysteretic properties such as ductility capacity, energy dissipation capacity, and strength degradation after buckling of thespecimen are performed. The compressive strength of BLMs is found to be relatively well predicted by the AISC LRFDSpecifications. BLMs with smaller kl/r were ductile but failed to reach the target ductility of 3.0 before starting to fracture,while those with larger kl/r could meet the ductility demand in most cases. The normalized energy dissipation ratio, ECETand the normalized compressive strength degradation, Cr"/Cr of BLMs typically decrease as normalized displacements δ/δbexpincrease, and the ratios for specimens with larger kl/r dropped more rapidly than for specimens with smaller kl/r; similartrends were observed for the monolithic braces. The BLMs with a smaller slenderness ratio, kl/r, and width-to-thickness ratio,b/t, experienced a larger number of inelastic cycles than those with larger ratios. 相似文献
10.
Conceptual study of X-braced frames with different steel grades using cyclic half-scale tests 总被引：1，自引：0，他引：1
In this paper,an experimental and analytical study of two half-scale steel X-braced frames with equal nominal shear strength under cyclic loading is described.In these tests,all members except the braces are similar.The braces are made of various steel grades to monitor the effects of seismic excitation.Internal stiffeners are employed to limit the local buckling and increase the fracture life of the steel bracing.A heavy central core is introduced at the intersection of the braces to decrease their effective length.Recent seismic specifications are considered in the design of the X-braced frame members to verify their efficiency.The failure modes of the X-braced frames are also illustrated.It is observed that the energy dissipation capacity,ultimate load capacity and ductility of the system increase considerably by using lower grade steel and proposed detailing.Analytical modeling of the specimens using nonlinear finite element software supports the experimental findings. 相似文献
11.
Christoph Mahrenholtz Pao‐Chun Lin An‐Chien Wu Keh‐Chyuan Tsai Shyh‐Jiann Hwang Ruei‐Yan Lin Muhammad Y. Bhayusukma 《地震工程与结构动力学》2015,44(1):59-78
Damage to buildings observed in recent earthquakes suggests that many old reinforced concrete structures may be vulnerable to the effects of severe earthquakes. One suitable seismic retrofit solution is the installation of steel braces to increase the strength and ductility of a building. Steel bracings have some compelling advantages such as their comparatively low weight, their suitability for prefabrication, and the possibility of openings for utilities, access, and light. The braces are typically connected to steel frames that are fixed to the concrete structure using post‐installed concrete anchors along the perimeter. However, these framed steel braces are not without some disadvantages such as heavier steel usage and greater difficulties during the installation. Therefore, braces without steel frames appear to be an attractive alternative. In this study, braces were connected to gussets furnished with anchor brackets, which were fixed by means of a few post‐installed concrete anchors. The clear structural system and the increased utilization of the anchors allowed the anchorage to be designed precisely and economically. The use of buckling‐restrained braces (BRBs) provides additional benefits in comparison with conventional braces. BRBs improve the energy dissipation efficiency and allow the limitation of the brace force to be taken up by the highly stressed anchorage. Cyclic loading tests were conducted to investigate the seismic performance of BRBs connected with post‐installed anchors used to retrofit reinforced concrete frames. The tests showed that the proposed design method is feasible and increases strength as well as ductility to an adequate seismic performance level. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
12.
Hiroshi Tagawa Yuki Tanaka Shohei Moriwake 《Bulletin of Earthquake Engineering》2018,16(11):5489-5502
Steel hollow section members are often applied as bracing in steel structures. Field-bolted connections of the slotted-in single splice plate and the gusset plate are popular because of their ease of construction. However, eccentricity between the splice and gusset plate axes reduces the compressive strength of the brace. This study proposes compressive strength improvement of rectangular hollow section braces using eccentrically installed splice plates such that the gusset plate axis coincides with the brace axis. To demonstrate the efficacy of the proposed concept, four compressive loading test results are examined in this study. Test results reveal the influences of splice plate eccentric installation on the brace compressive strength, the out-of-plane displacement, and the strain distribution. The proposed concept is effective for the brace with stiffened splice plates for inducing overall buckling with plastic hinges in the gusset plates. Variation of compressive strength is finally discussed based on the discrepancy between the brace axis and the axis of the plates in which the plastic hinges form at the overall buckling mode ends. 相似文献
13.
Cyclic loading tests and finite element analyses on six novel all‐steel buckling‐restrained braces (BRBs) are conducted using different loading patterns to investigate the core plate high‐mode buckling phenomenon. The proposed BRB is composed of a core member and a pair of identical restraining members, which restrains the core member by using bolted shim spacers. The design of the proposed BRB allows the core plate to be visually inspected immediately following a major earthquake. If necessary, the pair of restraining members can be conveniently disassembled, and the damaged core plate can be replaced. Test results indicate that the proposed BRBs can sustain large cyclic strain reversals and cumulative plastic deformations in excess of 400 times the yield strain. Experimental and analytical results confirm that the high‐mode buckling wavelength is related to the core plate thickness and the applied loading patterns. The larger the axial compressive strain is applied, the shorter the high‐mode buckling wavelength would be developed. The buckling wavelength is about 12 times the core plate thickness when the high‐mode buckling shape is fully developed. However, it reduces to about 10 times the core plate thickness when a compressive core strain reaches greater than 0.03. The high‐mode bucking wavelength can be satisfactorily predicted using the proposed method or from the finite element analysis. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
14.
A thin‐profile buckling‐restrained brace (thin‐BRB) consists of a rectangular steel casing and a flat steel core that is parallel to a gusset plate. A thin configuration reduces the width of the restraining member and thus saves usable space in buildings. However, deformable debonding layers, which cover the steel core plate in order to mitigate the difference between the peak tensile and compressive axial forces, provide a space for the steel core to form high mode buckling waves when the thin‐BRB is under compression. The wave crests squeeze the debonding layers and produce outward forces on the inner surface of the restraining member. If the restraining member is too weak in sustaining the outward forces, local bulging failure occurs and the thin‐BRB loses its compression capacity immediately. In order to investigate local bulging behavior, a total of 22 thin‐BRB specimens with a ratio of steel core plate to restraining steel tube depth ranging from 0.3 to 0.7 and axial yield force capacities ranging from 421 kN to 3036 kN were tested by applying either cyclically increasing, decreasing, or constant axial strains. The restraining steel tube widths of all the specimens were smaller than 200 mm and were infilled with mortar with a compressive strength of 97 MPa or 55 MPa. Thirteen of the 22 thin‐BRB specimens' restraining members bulged out when the compressive core strains exceeded 0.03. A seismic design method of the thin‐BRB in preventing local bulging failure is proposed in this study. Test and finite element model (FEM) analysis results suggest that the outward forces can be estimated according to the BRB compressive strength, steel core high mode buckling wavelength, and the debonding layer thickness. In addition, the capacity of the restraining member in resisting the outward forces can be estimated by using the upper bound theory in plastic analysis. Both the FEM analysis and test results indicate that the proposed method is effective in predicting the possibility of local bulging failure. Test results indicate that the proposed design method is conservative for thin‐BRB specimens with a large steel core plate to restraining steel tube depth ratio. This paper concludes with design recommendations for thin‐BRBs for severe seismic services. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
15.
This study is aimed at comparing the seismic performance of steel chevron braced frames (CBFs) with and without fluid viscous dampers (FVDs) as a function of the characteristics of the near‐fault (NF) ground motion and FVD parameters. For this purpose, comparative nonlinear time history (NLTH) analyses of single and multiple storey CBFs with and without FVDs are conducted using NF ground motions with various velocity pulse periods scaled to have small, moderate and large intensities. Additionally, NLTH analyses of single‐ and four‐storey CBFs with FVDs are conducted to study the effect of the damping ratio and velocity exponent of the FVD on the seismic performance of the frames. The analyses results revealed that the seismic performance of the CBFs without FVDs is very poor and sensitive to the velocity pulse period and the intensity of the NF ground motion due to brace‐buckling effects. Installing FVDs into the CBFs significantly improved their seismic performance by maintaining their elastic behaviour. Furthermore, FVDs with smaller velocity exponents and larger damping ratio are observed to be more effective in improving the seismic performance of the CBFs subjected to NF earthquakes. However, FVDs with damping ratios larger than 50% do not produce significant additional improvement in the seismic performance of the CBFs. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
16.
传统通过p-y曲线法分析强震状态下黄土中桩基动力性状时未进行桩基结构模拟,获取的强震状态下黄土中桩基动力的相关动力参数不准确。本文提出新的强震状态下黄土中桩基动力性状分析方法,依据HS硬化模型设计HSS本构模型,通过模型获取强震状态下黄土中桩基动力的相关参数,以此为基础采用PLAXIS软件构建黄土中桩基有限元模型;通过两种模型从耦合荷载作用下的桩基桩身水平位移响应、桩身内力响应两方面对强震状态下黄土桩基动力性状展开实验分析。实验结果表明,所提方法可对强震状态下黄土中桩基动力性状进行准确分析。 相似文献
17.
ABAQUS混凝土损伤塑性模型的动力性能分析 总被引：3，自引：0，他引：3
地震作用在混凝土结构上会在其材料中产生较高的应变率,混凝土材料具有一定的率敏感性,准确模拟混凝土结构在地震作用下的反应需采用混凝土动态本构模型。为评估ABAQUS有限元软件中的混凝土损伤塑性模型模拟混凝土动力性能的能力,采用该模型对混凝土材料和构件在不同加载速度下的动态反应进行了有限元数值分析。结果表明,随着加载速度的提高,混凝土的抗压强度提高,下降段坡度增大,混凝土梁的承载能力提高,模拟结果与相关试验结果吻合较好;该混凝土损伤塑性模型可以模拟混凝土材料和构件的主要动力特性,但也存在不足之处。 相似文献
18.
19.
Hayato Asada Andrew D. Sen Tao Li Jeffrey W. Berman Dawn E. Lehman Charles W. Roeder 《地震工程与结构动力学》2020,49(15):1619-1639
Current seismic design requirements for special concentrically braced frames (SCBFs) in chevron configurations require that the beams supporting the braces be designed to resist the demands resulting from the simultaneous yielding of the tension brace and degraded, post-buckling strength of the compression brace. Recent research, including large-scale experiments and detailed finite-element analyses, has demonstrated that limited beam yielding is not detrimental to chevron braced frame behavior and actually increases the story drift at which the braces fracture. These findings have resulted in new expressions for computing beam demands in chevron SCBFs that reduce the demand in the tension brace to be equal to the expected compressive capacity at buckling of the compression brace. In turn, the resultant force on the beam is reduced as is the required size of the beam. Further study was undertaken to investigate the seismic performance of buildings with SCBFs, including chevron SCBFs with and without yielding beams and X-braced frames. Prototype three- and nine-story braced frames were designed using all three framing systems, that is, chevron, chevron with yielding beams, and X SCBFs, resulting in six building frames. The nonlinear dynamic response was studied for ground motions simulating two different seismic hazard levels. The results were used to characterize the seismic performance in terms of the probability of salient damage states including brace fracture, beam vertical deformation, and collapse. The results demonstrate that the seismic performance of chevron SCBFs with limited beam yielding performs as well as or better than the conventionally designed chevron and X SCBFs. 相似文献
20.
Jeffrey Erochko Constantin Christopoulos Robert Tremblay Hyung‐Joon Kim 《地震工程与结构动力学》2013,42(11):1617-1635
The self‐centering energy dissipative (SCED) brace is a new steel bracing member that provides both damping to the structure and a re‐centering capability. The goal of this study was to confirm the behavior of SCED braces within complete structural systems and to confirm the ability to model these systems with both a state‐of‐the‐art computer model as well as a simplified model that would be useful to practicing engineers. To these ends, a three‐story SCED‐braced frame was designed and constructed for testing on a shake table. Two concurrent computer models of the entire frame were constructed: one using the opensees nonlinear dynamic modeling software, and a simplified model using the commercial structural analysis software sap2000 . The frame specimen was subjected to 12 significant earthquakes without any adjustment or modification between the tests. The SCED braces prevented residual drifts in the frame, as designed, and did not show any significant degradation due to wear. Both numerical models were able to predict the drifts, story shears, and column forces well. Peak story accelerations were overestimated in the models; this effect was found to be caused by the absence of transitions at stiffness changes in the hysteretic model of the braces. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献