共查询到20条相似文献，搜索用时 984 毫秒
1.
Clayey soils in the vicinity of energy geostructures may be exposed to long-term periodic thermal cycles. The creep and consolidation behaviors of the clayey soils can be both rate-dependent and temperature-dependent, and the underlying physical mechanisms are merely investigated theoretically. In this study, based on the theory of thermodynamics, a fully coupled thermo-hydro-mechanical (THM) finite element (FE) program for saturated soils is developed for this purpose. The FE formulation accounts for the combined effect of rate and temperature through the novel concept of granular temperature. Simulations of THM coupled validation cases and a series of experimental observations on the soft Bangkok clay are carried out. The obtained numerical results exhibit good agreement with analytical solutions and laboratory measurements. It is found that three fundamental physical mechanisms contribute to the irreversible thermal contraction observed for normally consolidated and lightly overconsolidated clays under drained thermal cycles: (1) the thermal creep excited by mass exchange from adsorbed water to free water; (2) the mechanical creep induced by confining stresses; and (3) the increase in granular packing caused by the thermal expansion of soil particles. The thermal contraction generally stabilizes within a few thermal cycles, as a result of the noticeable reduction in the thermal creep rate. It is further demonstrated that the transient heat transfer and the heating rate can greatly influence the deformation of clays subjected to thermal cycles.
相似文献2.
通过室内试验,研究了超固结比OCR对不同温度路径下中空圆柱饱和粉质黏土热固结特性的影响。研究表明,同一升温过程、不同超固结比试样所产生的最大孔压基本相同,但在相同的降温过程中,随着OCR的增大,产生的负孔压的绝对值有增大的趋势;升温或降温过程产生的体应变随着OCR的增大而减小,呈指数形式变化,并且温度幅度越大,这种变化幅度也越大;经过升温-降温过程后的最终体应变也随着OCR的增大而减小;升温或降温到同一温度值,其过程设置的温度等级越多,固结体应变也越大,并且随着OCR的增大,不同等级之间的体应变差值减小,而OCR对不同等级升温-降温后的最终体应变间的差值影响较小。 相似文献
3.
在精准温控动三轴试验系统上开展了不同温度及不同升温路径饱和黏土剪切试验研究,探讨了不同温度对饱和软黏土不排水剪切特性的影响,分析不同升温固结方式对饱和软黏土孔压发展、体变、强度以及模量的影响规律。试验结果显示：在4～76 ℃试验研究范围内,环境温度升高导致饱和软黏土的不排水剪切强度有所减少,但温度升高对土体模量增加影响明显,温度T和模量ET关系可用ET = 2.69T 0.3表达;升温变化时正常固结黏土产生超孔隙水压力并随着温度增大而增大,升温热固结后土的剪切强度将明显提高,且排水状态下升温固结对土剪切强度增长小于升温完成后再固结情况;土体从26 ℃分别升高20、40 ℃时,升温引起的超孔压比分别为0.41、0.61,剪切峰值强度分别增加8.23%、22.37%。研究表明：升温幅值增大会使土体热固结程度越大,升温分级越多,热固结也越充分,其对应的体变、强度增长率则越大;同时最终温度及热固结路径对其剪切相转换特征存在影响,升温越高、热固结路径越多其剪胀性越明显,但温度变化范围、固结分级、热固结路径总体上对孔隙水压力的发展基本不产生影响。 相似文献
4.
Tests on specimens of reconstituted illitic clay have examined the influence of temperature on the mechanical behaviour of clay soils. The program involved consolidation to effective confining pressures up to 1.5 MPa, heating to 100°C, and tests on normally consolidated and overconsolidated specimens with OCR = 2. The tests included isotropic consolidation, undrained triaxial compression with pore water pressure measurement, drained tests along controlled stress paths to investigate yielding behaviour, and undrained tests which involved heating and measurement of the resulting induced pore water pressures. The large strain strength envelope is independent of temperature. However, peak undrained strengths increase with temperature because smaller pore water pressures are generated during shearing. An important contribution from the study is a series of results for the yielding of illitic clay at three different temperatures. For the first time, there is clear evidence of yield loci decreasing in size with increasing temperature. An associated flow rule can be assumed without serious error. The results contribute to the confirmation of a thermal elastic-plastic soil model developed by the authors from cam clay following the addition of a small number of extra assumptions. Depending on the initial stress state, heating under undrained conditions may produce shear failure. 相似文献
5.
Matthieu Dumont Said Taibi Jean‐Marie Fleureau Nabil Abou‐Bekr Abdelghani Saouab 《国际地质力学数值与分析法杂志》2011,35(12):1299-1317
A simple thermo‐hydro‐mechanical (THM) constitutive model for unsaturated soils is described. The effective stress concept is extended to unsaturated soils with the introduction of a capillary stress. This capillary stress is based on a microstructural model and calculated from attraction forces due to water menisci. The effect of desaturation and the thermal softening phenomenon are modelled with a minimal number of material parameters and based on existing models. THM process is qualitatively and quantitatively modelled by using experimental data and previous work to show the application of the model, including a drying path under mechanical stress with transition between saturated and unsaturated states, a heating path under constant suction and a deviatoric path with imposed suction and temperature. The results show that the present model can simulate the THM behaviour in unsaturated soils in a satisfactory way. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
6.
Kousik Deb 《国际地质力学数值与分析法杂志》2008,32(10):1267-1288
The present study pertains to the development of a mechanical model for predicting the behavior of granular bed‐stone column‐reinforced soft ground. The granular layer that has been placed over the stone column‐reinforced soft soil has been idealized by the Pasternak shear layer. The saturated soft soil has been idealized by the Kelvin–Voigt model to represent its time‐dependent behavior and the stone columns are idealized by stiffer Winkler springs. The nonlinear behavior of the granular fill has been incorporated in this study by assuming a hyperbolic variation of shear stress with shear strain as in one reported literature. Similarly, for soft soil it has also been assumed that load‐settlement variation is hyperbolic in nature. The effect of consolidation of the soft soil due to inclusion of the stone columns has also been included in the model. Plane‐strain conditions are considered for the loading and foundation soil system. The numerical solutions are obtained by a finite difference scheme and the results are presented in a non‐dimensional form. Parametric studies for a uniformly loaded strip footing have been carried out to show the effects of various parameters on the total as well as differential settlement and stress concentration ratio. It has been observed that the presence of granular bed on the top of the stone columns helps to transfer stress from soil to stone columns and reduces maximum as well as differential settlement. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
7.
8.
9.
针对长江口地区的重塑饱和海洋黏土,进行了一系列均等固结条件下的应力控制式轴向-扭转双向耦合循环剪切试验,着重探讨了循环荷载分量比R与超固结比OCR对孔压与动强度特性的影响。试验结果表明,随着R的减小,波动孔压幅值逐渐降低,而残余孔压先降低后升高,R = 1时残余孔压最小。在循环耦合剪切作用过程中,对应相同循环次数,随着OCR的增大,累积孔压变小,而波动孔压幅值却在增大。对应相同循环次数比N/Nf,随着OCR增大,残余孔隙水压力比ur / urmax减小。经归一化处理后ur / urmax-N/Nf关系曲线对于正常固结与超固结饱和黏土可分别用不同的表达式来表达。随着R的降低,破坏循环次数先增大后减小,R = 1时最大。随着OCR的增大,饱和黏土的强度变化减小 相似文献
10.
Matthieu Dumont Said Taibi Jean-Marie Fleureau Nabil Abou Bekr Abdelghani Saouab 《Comptes Rendus Geoscience》2010,342(12):892-900
A simple thermohydromechanical (THM) constitutive model for unsaturated soils is described. The effective stress concept is extended to unsaturated soils with the introduction of a capillary stress. This capillary stress is based on a microstructural model and calculated from attraction forces due to water menisci. The effect of desaturation and the thermal softening phenomenon are modelled with a minimal number of material parameters and based on existing models. THM process is qualitatively and quantitatively modelled by using experimental data and previous work to show the application of the model, including a drying path under mechanical stress with transition between saturated and unsaturated states, a heating path under constant suction and a deviatoric path with imposed suction and temperature. The results show that the present model can simulate the THM behaviour in unsaturated soils in a satisfactory way. 相似文献
11.
为研究主应力轴旋转复杂动应力对偏压固结粉土的性状演变影响,以空心圆柱试样为对象,开展具有不同初始固结比的密实粉土（Dr＝70%）在不排水主应力轴循环旋转下的系列试验。结果表明：①初始固结比不大于1.5时,主应力轴旋转导致试样发生中低应变崩塌,进而液化的脆性破坏模式;而固结比大于1.5时,试样变为应变持续稳定开展至高应变,孔压最终进入动态平衡的延性破坏模式,且不同固结比下试样发生崩塌液化和稳态延性破坏的孔压峰值间不存在交叉。②小偏压固结试样的液化峰值孔压和崩塌孔压均随固结比增加而有规律地下降,但受动剪应力水平影响很小,这与等压固结试样的崩塌孔压值受控于剪应力水平有很大差异。③相同初始球应力水平下,崩塌振次反映的小偏压固结试样强度高于等压固结试样,但在偏压条件下强度与固结比不存在单调变化关系,表明小偏压固结试样崩塌除受制初始围压水平外,很大程度上还取决于偏压程度。④基于上述试验结果,提出了主应力轴循环旋转下小偏压固结粉土的孔压预测模型,该模型不仅突显了崩塌状态对相变及液化破坏的重要预测作用,还反映了固结比和动剪应力对孔压开展的综合影响。 相似文献
12.
Subway tunnels and their surrounding geotechnical media are taken as an entirety, namely, tunnel-geomaterial system (TGS), and the stability and durability of the subway tunnels are subjected to the responses of the TGS to the thermal (T), hydraulic (H) and mechanical (M) loadings and their coupled effects. Modeling of the coupled THM processes that occur in the TGS are important for reliably assessing and predicting the performance of subway tunnels. Therefore, a numerical model of coupling the THM processes in the TGS is developed incorporating the equilibrium, motion, constitutive and compatibility equations. The proposed model considers full coupling between the thermal (temperature variation), hydraulic (water seepage), mechanical (subsidence) processes and changes in the material properties, such as stress-strain relation, viscosity, thermal conductivity, and hydraulic conductivity. The developed model is validated through comparisons of field tests, laboratory experiments and numerical simulations. Favorable agreement between the modeling results and the compared data verifies the capability of the developed model to well describe the THM behavior of subway tunnels in the TGS and their evolutions. 相似文献
13.
利用GDS应力路径三轴试验系统对南阳膨胀土进行3种应力速率下、4种超固结比（OCR）的被动压缩三轴试验及3种超固结比的被动挤伸三轴试验,分析了不同超固结比和应力速率下其应力（孔隙水压力）-应变关系、有效应力路径及变形模量的演化规律,对膨胀土变形模量各向异性特性进行了初步探讨。结果表明,应力速率、超固结比及卸荷路径均对膨胀土力学特性有一定影响。在被动压缩路径和被动挤伸路径下,随着应力速率和超固结比的增加,相同轴向应变时的偏应力值单调增加;不同超固结比和应力速率时膨胀土的孔隙水压力始终为负值,且其降幅总体上随超固结比的增加而增大,但其降幅随应力速率的变化规律与剪切路径有关。在被动压缩路径下,相同应变时不同应力速率下的孔压降幅基本相同;而在被动挤伸路径下,其降幅随应力速率的增加而增大。边坡开挖路径的选择对于边坡变形影响显著,被动挤伸路径下达到设定极限偏应力时的轴向应变明显大于被动压缩路径。膨胀土变形模量E100随着超固结比和应力速率的增加而增加,但各应力速率下变形模量的各向异性特性则随着超固结比的增加而变弱。 相似文献
14.
水泥加固不同地区软土的试验研究 总被引：1，自引：0，他引：1
对不同地区软土经水泥加固后的强度形成特征进行了研究。进行直接剪切试验及无侧限抗压试验测定了水泥加固土的力学指标,发现不同地区的软土经水泥加固后力学性质存在很大差异,从试样的粒度成分、有机质含量及加固后试样的微观结构特征等方面对此进行解释。结果表明,试样的粒度成分及有机质含量会对加固效果产生很大影响,黏粒含量越大,有机质含量越高,对水泥加固土强度的形成越不利。为在用水泥进行不同性质的软土加固处理时采取合理的附加措施提供了理论依据。 相似文献
15.
为了研究温度对水饱和边坡夹层力学参数的影响,将水饱和边坡夹层视为固-液两相的线弹性体,建立了水饱和边坡夹层热-孔隙水-力耦合作用的力学模型,并推导了其耦合控制方程;采用物理相似模拟的方法,建立了与边坡原型相似的试验模型,研究温度引起的边坡夹层力学参数的变化特征;通过比较分析理论计算结果与模型试验结果,验证了所建立的耦合力学模型的适用性。研究结果表明：孔隙水压力系数和热压力系数是引起水饱和边坡夹层孔隙水压力增加的关键控制因素;孔隙水压力系数取决于孔隙排水压缩特性和固相介质压缩特性,这两者差值越大,孔隙水压力系数越大;孔隙水热膨胀系数和孔隙体积热膨胀系数是影响热压力系数的主要因素,这两者差值越大,热压力系数也越大;边坡夹层孔隙水压力随温度升高呈现出先缓慢增加而后急剧增加的变化特征,而黏聚力和抗剪强度随温度升高而缓慢降低,且孔隙水压力的理论计算结果与试验测试结果吻合良好。因此,水饱和边坡夹层热-孔隙水-力耦合作用的力学模型能较好地反映孔隙水压力在加热升温过程中的变化特征,为科学地预测和控制类似边坡工程的稳定性提供了参考。 相似文献
16.
17.
针对塑料排水板(PVD)安装热源能提升PVD性能、加速竖井地基固结这一工程现象,基于热-水-应力 (T-H-M) 三场全耦合的有限元方法来模拟利用热源进行地基处理新技术(PVTD)。首先,以微分形式与等效弱形式分别给出T-H-M耦合控制方程,并推导出其有限元方程组。然后在多场耦合有限元软件中建立饱和土的T-H-M全耦合模型,并通过与已有解析解比较,验证了模型正确性。最后,对一个经典有涂抹区的竖井地基算例,分不耦合温度(UT)、耦合温度但不考虑其对饱和土物性影响(CT)、耦合温度考虑温度对饱和土渗透性影响(CTP) 3种情况进行固结计算分析。研究结果表明,相对于无热源竖井地基,CT情况下由于热源产生的附加孔隙水压力,固结速度略有下降;CTP情况下,由于热源有效改善涂抹区的渗透性能,竖井地基固结速率明显加快。上述研究结论从理论上较好地阐明了PVTD的作用机制。 相似文献
18.
Utilizing basic balance laws of saturated granular media, a theoretical model for describing the phenomena of dilatation and densification of dry sand, as well as the increase of pore water pressure of saturated sand during shear loading, is developed. An expression for the free-energy function of loose sands is postulated, and the problem of static shearing of a sand sample is analyzed. Predictions of the model for pore water pressure are compared with those obtained experimentally for dry pluviated and moist vibrated samples of fine Ottawa sand and solid-glass beads and discussed. 相似文献
19.
软土在不同应力路径下的力学特性分析 总被引：7，自引：0，他引：7
通过固结不排水剪应力路径试验对广州南沙典型软土在不同固结条件的力学特性进行了系统研究。分析了初始固结状态对软黏土应力路径依赖性的影响,比较了不同应力路径下土的应力-应变关系特征和孔隙水压力变化规律,探讨了孔压分布与土体变形特征的关系,认为侧向卸荷会造成剪应力增加、体应力减小,从而使土体产生剪胀趋势。研究结果还表明,不排水条件下的有效应力路径主要与土样初始固结状态有关,因而同一固结状态下的有效应力路径具有唯一性。另外,试验中的剪切控制方式对有效应力路径有明显影响,但对土体抗剪强度的影响可以忽略。 相似文献
