共查询到20条相似文献，搜索用时 15 毫秒
1.
Nearly 40 years ago, Neuman (1968) developed an analytical solution for drawdown in a system of three aquifers separated by two aquitards when one of the aquifers is pumped at a constant rate. Whereas the simpler case of two aquifers separated by one aquitard has been presented by Neuman and Witherspoon (1969a), the full five-layer solution has not been previously evaluated. We do so here using numerical inversion of its Laplace-transformed version and present selected results graphically in dimensionless form. The solution demonstrates that the effect of pumping propagates across all five layers, adding emphasis to a question previously raised by Neuman and Witherspoon about the validity of leaky aquifer theories that disregard drawdowns in unpumped aquifers. A large-scale, long-term pumping test spanning three aquifers separated by two aquitards near Oxnard, California, has been conducted and analyzed by Neuman and Witherspoon (1972). They evaluated the vertical hydraulic diffusivities of the aquitards using the Neuman-Witherspoon ratio method and their specific storage values on the basis of laboratory consolidation tests. We reinterpret the Oxnard pumping test by coupling the five-layer analytical solution of Neuman (1968) with the parameter estimation code PEST (Doherty 2002) and validate our results against drawdowns from a subsequent pumping test at the site. Our parameter estimates compare favorably with those of Neuman and Witherspoon (1972). 相似文献
2.
The Kuwait Group consists mainly of clastic sediments overlying unconformably the Dammam Formation of Tertiary age. The Kuwait Group is generally divided into three main hydrostratigraphic units: the upper and lower aquifers separated by an aquitard. The upper aquifer is further divided into the water table aquifer, an aquitard and a semiconfined aquifer. This semiconfined unit was pumped and the drawdowns were observed in piezometers screened in various subunits of the Kuwait Group. Some pumping tests of short duration were carried out in the top water table aquifer as well. These tests showed that the subunits of the Kuwait Group are hydraulically interconnected to a varying degree.
The pumping test data were analysed using conventional analytical solutions. The semiconfined pumping test was also simulated by a quasi-three-dimensional model using a leaky multiaquifer modelling technique. The initial hydraulic parameters were improved manually in the model till best fit drawdowns were obtained.
The final parameters obtained by simulation of the pumping tests were used in designing a pilot drainage system for the control of a rising groundwater table in parts of Kuwait City. 相似文献
3.
We present the first demonstration of hydraulic tomography (HT) to estimate the three-dimensional (3D) hydraulic conductivity (K) distribution of a fractured aquifer at high-resolution field scale (HRFS), including the fracture network and connectivity through it. We invert drawdown data collected from packer-isolated borehole intervals during 42 pumping tests in a wellfield at the former Naval Air Warfare Center, West Trenton, New Jersey, in the Newark Basin. Five additional tests were reserved for a quality check of HT results. We used an equivalent porous medium forward model and geostatistical inversion to estimate 3D K at high resolution (K blocks <1 m3), using no strict assumptions about K variability or fracture statistics. The resulting 3D K estimate ranges from approximately 0.1 (highest-K fractures) to approximately 10−13 m/s (unfractured mudstone). Important estimated features include: (1) a highly fractured zone (HFZ) consisting of a sequence of high-K bedding-plane fractures; (2) a low-K zone that disrupts the HFZ; (3) several secondary fractures of limited extent; and (4) regions of very low-K rock matrix. The 3D K estimate explains complex drawdown behavior observed in the field. Drawdown tracing and particle tracking simulations reveal a 3D fracture network within the estimated K distribution, and connectivity routes through the network. Model fit is best in the shallower part of the wellfield, with high density of observations and tests. The capabilities of HT demonstrated for 3D fractured aquifer characterization at HRFS may support improved in situ remediation for contaminant source zones, and applications in mining, repository assessment, or geotechnical engineering. 相似文献
4.
Shabbir A. S. Sayed 《Ground water》1984,22(2):148-153
In order to understand the flow pattern around a pumping well partially penetrating a vertically extensive aquifer, a specially designed pumping test was carried out in Pakistan. In this paper salient features of the test have been described. The spatial distributions of drawdown have been shown graphically. Some of the preliminary conclusions made from the drawdown pattern include:
- • The distance beyond which the flow is likely to be horizontal increases with decrease in the degree of aquifer penetration.
- • In equidistant observation wells open at different depths, (1) the drawdowns tend to merge at larger times, provided the observation point is located within the screened section of the aquifer; (2) the less the depth of penetration is, the earlier the drawdowns start merging; and (3) the initial rate of drawdown near the aquifer top is slow but catches up with time to exceed those at deeper points.
5.
Collection of water-level recovery data is a common practice for pumping tests. The resulting data can provide some of the most useful information from the tests, but are rarely used to their full value. van der Kamp (1989) proposed a general method that uses recovery data to extend the effective duration of pumping. The method is straightforward to implement and applicable for simple or complex hydrogeologic settings. The only assumption invoked is that the response remains linear such that the principle of superposition can be applied. No other assumptions about the properties of the aquifer are required. The method can greatly increase the value of pumping tests by extending the effective duration of the tests for as long as significant residual drawdowns are observed. 相似文献
6.
Detecting and quantifying small drawdown at observation wells distant from the pumping well greatly expands the characterized aquifer volume. However, this detection is often obscured by water level fluctuations such as barometric and tidal effects. A reliable analytical approach for distinguishing drawdown from nonpumping water‐level fluctuations is presented and tested here. Drawdown is distinguished by analytically simulating all pumping and nonpumping water‐level stresses simultaneously during the period of record. Pumping signals are generated with Theis models, where the pumping schedule is translated into water‐level change with the Theis solution. This approach closely matched drawdowns simulated with a complex three‐dimensional, hypothetical model and reasonably estimated drawdowns from an aquifer test conducted in a complex hydrogeologic system. Pumping‐induced changes generated with a numerical model and analytical Theis model agreed (RMS as low as 0.007 m) in cases where pumping signals traveled more than 1 km across confining units and fault structures. Maximum drawdowns of about 0.05 m were analytically estimated from field investigations where environmental fluctuations approached 0.2 m during the analysis period. 相似文献
7.
Nikolaos Nagkoulis 《Ground water》2021,59(3):410-416
This paper deals with water pumping cost minimization, in a confined infinite aquifer, proposing an alternate pulsed pumping schedule. The transient flow analysis is conducted for two wells with equal pumping rates. Specifically, two pumping schedules are analytically compared. In the first case, well users pump simultaneously, and in the second one they cooperate so that they pump alternately. This paper proves that the proposed alternate pumping schedule works as a stabilizer, reducing the high hydraulic drawdowns values, regardless of the aquifer characteristics. Moreover, pumping alternately is better in terms of pumping cost, compared to simultaneous pumping, though benefit become negligible as distance between wells becomes large. Two simplified equations are proposed, one to find the difference of the hydraulic drawdowns between the two pumping schedules and the other one to find the economic benefit of each well from cooperation. The equations are finally applied to a number of cases and their results are compared to the results obtained from an algorithm created to calculate the hydraulic drawdowns and the pumping cost, using the Theis equation. The results can be very useful in irrigation scheduling, as they can be applied to systems of well users/farmers, to reduce pumping cost. 相似文献
8.
One of the challenges in characterizing fractured-rock aquifers is determining whether the equivalent porous medium approximation is valid at the problem scale. Detailed hydrogeologic characterization completed at a small study site in a densely fractured dolomite has yielded an extensive data set that was used to evaluate the utility of the continuum and discrete-fracture approaches to aquifer characterization. There are two near-vertical sets of fractures at the site; near-horizontal bedding-plane partings constitute a third fracture set. Eighteen boreholes, including five coreholes, were drilled to a depth of approximately 10.6 m. Borehole geophysical logs revealed several laterally extensive horizontal fractures and dissolution zones. Flowmeter and short-interval packer testing identified which of these features were hydraulically important. A monitoring system, consisting of short-interval piezometers and multilevel samplers, was designed to monitor four horizontal fractures and two dissolution zones. The resulting network consisted of >70 sampling points and allowed detailed monitoring of head distributions in three dimensions. Comparison of distributions of hydraulic head and hydraulic conductivity determined by these two approaches suggests that even in a densely fractured-carbonate aquifer, a characterization approach using traditional long-interval monitoring wells is inadequate to characterize ground water movement for the purposes of regulatory monitoring or site remediation. In addition, traditional multiwell pumping tests yield an average or bulk hydraulic conductivity that is not adequate for predicting rapid ground water travel times through the fracture network, and the pumping test response does not appear to be an adequate tool for assessing whether the porous medium approximation is valid. 相似文献
9.
Abstract A pumping test was conducted along the Mullica River in the Wharton Tract, New Jersey as part of a water-resources investigation. Impermeable bog iron caps parts of the flood plain and channel so that ground-water recharge moves directly into the river. Observation wells on both sides of the river tapped water-bearing zones at 25 (shallow), 50 (medium), and 100 (deep) feet. A pumping well, screened in the medium zone, caused abrupt drawdowns which leveled off after a few minutes. Shape of the drawdown cone established early and changed little throughout the test. Piezometric surfaces were steepest on the southwest, indicating that most water came from there. Uninterrupted contour trends beneath the river show that here relatively little water entered the aquifer. Head differentials between the zones were greatest at the pumping well. Movement from the deep to medium zones was confined largely to the pumping-well vicinity. Pumping produced extensive reductions in the original areas of upward gradient between the medium and shallow zones; thus, areas of downward leakage became connected across the river. Piezometric head beneath the river was progressively lowered and caused the flood plain to dry; it became wet again when pumping stopped. The well field recovered to natural conditions in about 24 hours. Lack of hydraulic continuity between the river and aquifer results from bog iron deposits. Their removal will improve the continuity, and it appears feasible to induce river recharge to nearby pumping wells. 相似文献
10.
The buried-valley aquifers that are common in the glacial deposits of the northern hemisphere are a typical case of the strip aquifers that occur in many parts of the world. Pumping from a narrow strip aquifer leads to much greater drawdown and much more distant drawdown effects then would occur in a sheet aquifer with a similar transmissivity and storage coefficient. Widely used theories for radial flow to wells, such as the Theis equation, are not appropriate for narrow strip aquifers. Previously published theory for flow to wells in semiconfined strip aquifers is reviewed and a practical format of the type curves for pumping-test analysis is described. The drawdown response of strip aquifers to pumping tests is distinctive, especially for observation wells near the pumped well. A case study is presented, based on extensive pumping test experience for the Estevan Valley Aquifer in southern Saskatchewan, Canada. Evaluation of groundwater resources in such buried-valley aquifers needs to take into account the unusually large drawdowns in response to pumping. 相似文献
11.
Traditional analysis methods used to determine hydraulic properties from pumping tests work well in many porous media aquifers, but they often do not work in heterogeneous and fractured‐rock aquifers, producing non‐plausible and erroneous results. The generalized radial flow model developed by Barker (1988) can reveal information about heterogeneity characteristics and aquifer geometry from pumping test data by way of a flow dimension parameter. The physical meaning of non‐integer flow dimensions has long been a subject of debate and research. We focus on understanding and interpreting non‐radial flow through high permeability conduits within fractured aquifers. We develop and simulate flow within idealized non‐radial flow conduits and expand on this concept by simulating pumping in non‐fractal random fields with specific properties that mimic persistent sub‐radial flow responses. Our results demonstrate that non‐integer flow dimensions can arise from non‐fractal geometries within aquifers. We expand on these geometric concepts and successfully simulate pumping in random fields that mimic well‐test responses seen in the Culebra Dolomite above the Waste Isolation Pilot Plant. 相似文献
12.
S. Puri 《Ground water》1984,22(5):538-543
Flow simulations supplemented resource evaluation studies of the Lower Greensand aquifer. The annual recharge has hitherto been considered to be the resource available for development although a large confined storage exists. Pumping is principally in urban areas but recent monitoring suggests that the aquifer may have suffered excessive drawdowns. Therefore, simulation studies were carried out to refine the annual recharge estimate, to define the past effects of pumping and to obtain an indication of future trends. Catchment water balance indicates average annual recharge of 28 × 106 m3. One-dimensional (ID) ground-water flow simulation suggests that regional abstractions affect outcrop-water levels. The study showed that the aquifer reached a new equilibrium with the current pumping regime. An improved insight to the aquifer has permitted the formulation of strategies for future resource development. 相似文献
13.
We present a novel method to estimate the hydraulic and storage properties of a heterogeneous aquifer system using pilot-point-based hydraulic tomography (HT) inversion in conjunction with a geophysical a priori model. The a priori model involved a soil stratification obtained by combining electrical resistivity tomography inversion and field data from hydrogeological experiments. Pilot-point densities were assigned according to the stratification, which also constrained aquifer parameters during HT inversion. The forward groundwater flow model, HydroGeoSphere, was supplied to the parameter-estimation tool, PEST, to perform HT inversion. The performance of our method was evaluated on a hypothetical, two-dimensional, multi-layered, granitic aquifer system representative of those commonly occurring in the Kandi region in Telangana. Inversion results were compared using two commonly adopted methods of modeling parameter-heterogeneity: (1) using piece-wise zones of property values obtained from geostatistical interpolation of local-scale estimates; and (2) HT inversion starting from a homogeneous parameter field with a uniform distribution of pilot-points. Performances of the inverted models were evaluated by conducting independent pumping tests and statistical analyses (using a Taylor diagram) of the model-to-measurement discrepancies in drawdowns. Our results showed that using the aforementioned geophysical a priori model could improve the parameter-estimation process. 相似文献
14.
We have investigated non‐Darcian flow to a vertical fracture represented as an extended well using a linearization procedure and a finite difference method in this study. Approximate analytical solutions have been obtained with and without the consideration of fracture storage based on the linearization procedure. A numerical solution for such a non‐Darcian flow case has also been obtained with a finite difference method. We have compared the numerical solution with the approximate analytical solutions obtained by the linearization method and the Boltzmann transform. The results indicate that the linearized solution agrees generally well with the numerical solution at late times, and underestimates the dimensionless drawdown at early times, no matter if the fracture storage is considered or not. When the fracture storage is excluded, the Boltzmann transform solution overestimates the dimensionless drawdown during the entire pumping period. The dimensionless drawdowns in the fracture with fracture storage for different values of dimensionless non‐Darcian hydraulic conductivity β approach the same asymptotic value at early times. A larger β value results in a smaller dimensionless drawdown in both the fracture and the aquifer when the fracture storage is included. The dimensionless drawdown is approximately proportional to the square root of the dimensionless time at late times. 相似文献
15.
We jointly invert field data of flowmeter and multiple pumping tests in fully screened wells to estimate hydraulic conductivity using a geostatistical method. We use the steady-state drawdowns of pumping tests and the discharge profiles of flowmeter tests as our data in the inference. The discharge profiles need not be converted to absolute hydraulic conductivities. Consequently, we do not need measurements of depth-averaged hydraulic conductivity at well locations. The flowmeter profiles contain information about relative vertical distributions of hydraulic conductivity, while drawdown measurements of pumping tests provide information about horizontal fluctuation of the depth-averaged hydraulic conductivity. We apply the method to data obtained at the Krauthausen test site of the Forschungszentrum Jülich, Germany. The resulting estimate of our joint three-dimensional (3D) geostatistical inversion shows an improved 3D structure in comparison to the inversion of pumping test data only. 相似文献
16.
Identifying connections in a fractured rock aquifer using ADFTs 总被引：1，自引：0，他引：1
Fractured rock aquifers are difficult to characterize because of their extremely heterogeneous nature. Developing an understanding of fracture network hydraulic properties in these aquifers is difficult and time consuming, and field testing techniques for determining the location and connectivity of fractures in these aquifers are limited. In the Clare Valley, South Australia, well interference is an important issue for a major viticultural area that uses a fractured aquifer. Five fracture sets exist in the aquifer, all dipping > 25 degrees . In this setting, we evaluate the ability of steady-state asymmetric dipole-flow tests (ADFTs) to determine the connections between a test well and a set of piezometers. The procedure involves dividing a test well into two chambers using a single packer and pumping fluid from the upper chamber to the lower chamber. By conducting a series of tests at different packer elevations, an "input" signal is generated in fracture zones connected to the test well. By monitoring the "output" response of the hydraulic dipole field at piezometers, the connectivity of the fractures between the test well and piezometers can be determined. Results indicate the test well used in this study is connected in a complex three-dimensional geometry, with drawdown occurring above and below areas of potentiometric buildup. The ADFT method demonstrates that the aquifer evaluated in this study cannot be modeled effectively on the well scale using continuum flow models. 相似文献
17.
We have developed a method for analytically solving the porous medium flow equation in many different geometries for horizontal (two‐dimensional), homogeneous and isotropic aquifers containing impermeable boundaries and any number of pumping or injection wells located at arbitrary positions within the system. Solutions and results are presented for rectangular and circular aquifers but the method presented here is easily extendible to many geometries. Results are also presented for systems where constant head boundary conditions can be emulated internal to the aquifer boundary. Recommendations for extensions of the present work are briefly discussed. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
18.
A new method was developed for conducting aquifer tests in fractured-rock flow systems that have a pump-and-treat (P&T) operation for containing and removing groundwater contaminants. The method involves temporary shutdown of individual pumps in wells of the P&T system. Conducting aquifer tests in this manner has several advantages, including (1) no additional contaminated water is withdrawn, and (2) hydraulic containment of contaminants remains largely intact because pumping continues at most wells. The well-shutdown test method was applied at the former Naval Air Warfare Center (NAWC), West Trenton, New Jersey, where a P&T operation is designed to contain and remove trichloroethene and its daughter products in the dipping fractured sedimentary rocks underlying the site. The detailed site-scale subsurface geologic stratigraphy, a three-dimensional MODFLOW model, and inverse methods in UCODE_2005 were used to analyze the shutdown tests. In the model, a deterministic method was used for representing the highly heterogeneous hydraulic conductivity distribution and simulations were conducted using an equivalent porous media method. This approach was very successful for simulating the shutdown tests, contrary to a common perception that flow in fractured rocks must be simulated using a stochastic or discrete fracture representation of heterogeneity. Use of inverse methods to simultaneously calibrate the model to the multiple shutdown tests was integral to the effectiveness of the approach. 相似文献
19.
A mathematical model that describes the drawdown due to constant pumpage from a finite radius well in a two‐zone leaky confined aquifer system is presented. The aquifer system is overlain by an aquitard and underlain by an impermeable formation. A skin zone of constant thickness exists around the wellbore. A general solution to a two‐zone leaky confined aquifer system in Laplace domain is developed and inverted numerically to the time‐domain solution using the modified Crump (1976) algorithm. The results show that the drawdown distribution is significantly influenced by the properties and thickness of the skin zone and aquitard. The sensitivity analyses of parameters of the aquifer and aquitard are performed to illustrate their effects on drawdowns in a two‐zone leaky confined aquifer system. For the negative‐skin case, the drawdown is very sensitive to the relative change in the formation transmissivity. For the positive‐skin case, the drawdown is also sensitive to the relative changes in the skin thickness, and both the skin and formation transmissivities over the entire pumping period and the well radius and formation storage coefficient at early pumping time. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
20.
The interaction between a gaining stream and a water-table aquifer is studied at an outwash plain. The aquifer is hydraulically well connected to the stream. Pumping tests were carried out in 1997 and 1998 in two wells 60 m from the stream, screening different depths of the aquifer. Drawdown was measured on both sides of the stream. Hydraulic head, drawdown, and stream depletion data were analyzed using numerical flow models. Similar models were fitted to each of two different data sets: Model A was fitted to steady-state hydraulic head and streamflow gain data not influenced by pumping; and model B was fitted to drawdown data measured during the 1998 pumping test. Each calibrated model closely fits its calibration data; however, predictions were biased if model A was used to predict the calibration data of model B, and vice versa. To further test the models, they were used to predict streamflow depletion during the two pumping tests as well as the drawdown during the 1997 test. Neither of these data were used for calibration. Model A predicted the measured depletions fairly accurately during both tests, whereas the predicted drawdowns in 1997 were significantly larger than actually measured. Contrary to this, the 1997 drawdowns predicted by model B were nearly unbiased; the predicted depletions deviate significantly from the measured depletions in 1997, but they compare well with the observations in 1998. Thus, although field work and analyses were extensive and done carefully to develop a ground water flow model that could predict both drawdown and streamflow depletion, the model predictions are biased. Analyses indicate that the deviations between model and data may be because of error in the models' representations of either the release of water from storage or of the hydrology in the riparian zone. 相似文献