共查询到20条相似文献，搜索用时 78 毫秒
1.
Computational simulation of slab vibration and horizontal‐vertical coupling in a full‐scale test bed subjected to 3D shaking at E‐Defense 
下载免费PDF全文
下载免费PDF全文 This paper focuses on slab vibration and a horizontal‐vertical coupling effect observed in a full‐scale 5‐story moment frame test bed building in 2 configurations: isolated with a hybrid combination of lead‐rubber bearings and cross‐linear (rolling) bearings, and fixed at the base. Median peak slab vibrations were amplified—relative to the peak vertical shake table accelerations—by factors ranging from 2 at the second floor to 7 at the roof, and horizontal floor accelerations were significantly amplified during 3D (combined horizontal and vertical) motions compared with 2D (horizontal only) motions of comparable input intensity. The experimentally observed slab accelerations and the horizontal‐vertical coupling effect were simulated through a 3D model of the specimen using standard software and modeling assumptions. The floor system was modeled with frame elements for beams/girders and shell elements for floor slabs; the insertion point method with end joint offsets was used to represent the floor system composite behavior, and floor mass was finely distributed through element discretization. The coupling behavior was partially attributed to the asymmetry of the building that was intensified by asymmetrically configured supplemental mass at the roof. Horizontal‐vertical coupled modes were identified through modal analysis and verified with evaluation of floor spectral peaks. 相似文献
2.
Xiaodong Ji Kouichi Kajiwara Takuya Nagae Ryuta Enokida Masayoshi Nakashima 《地震工程与结构动力学》2009,38(12):1381-1399
When subjected to long‐period ground motions, high‐rise buildings' upper floors undergo large responses. Furniture and nonstructural components are susceptible to significant damage in such events. This paper proposes a full‐scale substructure shaking table test to reproduce large floor responses of high‐rise buildings. The response at the top floor of a virtual 30‐story building model subjected to a synthesized long‐period ground motion is taken as a target wave for reproduction. Since a shaking table has difficulties in directly reproducing such large responses due to various capacity limitations, a rubber‐and‐mass system is proposed to amplify the table motion. To achieve an accurate reproduction of the floor responses, a control algorithm called the open‐loop inverse dynamics compensation via simulation (IDCS) algorithm is used to generate a special input wave for the shaking table. To implement the IDCS algorithm, the model matching method and the H∞ method are adopted to construct the controller. A numerical example is presented to illustrate the open‐loop IDCS algorithm and compare the performance of different methods of controller design. A series of full‐scale substructure shaking table tests are conducted in E‐Defense to verify the effectiveness of the proposed method and examine the seismic behavior of furniture. The test results demonstrate that the rubber‐and‐mass system is capable of amplifying the table motion by a factor of about 3.5 for the maximum velocity and displacement, and the substructure shaking table test can reproduce the large floor responses for a few minutes. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
3.
4.
A new seismic energy dissipation shear wall structure is proposed in this paper. The new shear wall is one with purposely built‐in vertical slits within the wall panel, and rubber belts as seismic energy dissipation devices are installed in the vertical slits. In order to verify this concept, shaking table tests of a 10‐storey shear wall model with rubber belts filled in the vertical slits were carried out, and comparison of seismic behaviour was made between the new shear wall system and a shear wall with reinforced concrete connecting beams as energy dissipation. Furthermore, the seismic behaviour of this new shear wall is analysed by a finite element time history analysis method. The test and analysis show that the new shear wall system has a very good ability to dissipate seismic energy and is easy to use in engineering practice. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
5.
Seismic upgrading of old masonry buildings by seismic isolation and CFRP laminates: a shaking-table study of reduced scale models 总被引：2，自引：2，他引：0
The efficiency of improving the seismic resistance of old masonry buildings by means of seismic isolation and confining the
structure with CFRP laminate strips has been investigated. Five models of a simple two-story brick masonry building with wooden
floors without wall ties have been tested on the shaking table. The control model has been built directly on the foundation
slab. The second model has been separated from it by a damp-proof course in the form of a PVC sheet placed in the bed-joint
between the second and the third course, whereas the third model has been isolated by rubber isolators placed between the
foundation slab and structural walls. Models four and five have been confined with CFRP laminate strips, simulating the wall
ties placed horizontally and vertically at floor levels and corners of the building, respectively. One of the CFRP strengthened
models has been placed on seismic isolators. Tests have shown that a simple PVC sheet damp-proof course cannot be considered
as seismic isolator unless adequately designed. Tests have also shown that the isolators alone did not prevent the separation
of the walls. However, both models confined with CFRP strips exhibited significantly improved seismic behavior. The models
did not collapse even when subjected to significantly stronger shaking table motion than that resisted by the control model
without wall ties. 相似文献
6.
变阻尼半主动结构控制振动台试验 总被引：5，自引：1，他引：4
在一个１：４的五层模型刚架结构上进行了变阻尼半主动结构控制振动台试验．在结构的底层安装了一个溢流阀式变阻尼控制器,输入几种不同的地震动并采用几种不同的控制算法对结构进行了变阻尼半主动控制。振动台试验结果表明,受阻尼半主动结构控制仅需要很少的电能,就可以达到较好的控制效果,是一种很有应用前景的结构振动控制方案。结合溢流阀式变阻尼控制器的特点,分析了一些因素对控制效果的影响． 相似文献
7.
This paper describes shaking table tests of a multi-storey scale-model building structure subjected to seismic excitation and controlled by a semi-active fluid damper control system. The semi-active dampers were installed in the lateral bracing of the structure and the mechanical properties of the dampers were modified according to control algorithms which utilized the measured response of the structure. A simplified time-delay compensation method was developed to account for delays within the control system. The results of the shaking table tests are presented and interpreted and analytical predictions are shown to compare reasonably well with the experimental results. © 1997 John Wiley & Sons, Ltd. 相似文献
8.
Seismic vibration control of building structures with multiple tuned mass damper floors integrated 下载免费PDF全文
下载免费PDF全文 Floor isolation system (FIS) achieving very small floor accelerations has been used to ensure human comfortability or protect important equipments in buildings. Tuned mass damper (TMD) with large mass ratios has been demonstrated to be robust with respect to the changes in structural properties. This paper presents the concept of a TMD floor vibration control system, which takes advantages of both the FIS and TMD. Such a system is called ‘TMD floor system’ herein. The TMD floor system (TMDFS) in which building floors serve as TMDs can achieve large mass ratio without additional masses. Furthermore, multiple TMD floors installed in a building can control multimode vibrations. Then, an optimal design process, where the objective function is set as the maximum magnitude of the frequency response functions of inter‐storey drifts, is proposed to determine the TMD floor parameters. Additionally, the multimode approach is applied to determine the optimal locations of TMD floors if not all of the floors in a building can serve as TMDs. In addition to the numerical simulations, a scaled model shaking table experiment is also conducted. Both the numerical and experimental results show that the absolute accelerations of the TMD floors are smaller than those of the main structural storeys, which indicates the TMDFS maintains the merit of FIS while greatly reducing seismic responses of main structures. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
9.
Earthquake‐induced structural pounding frequently causes serious damage to buildings, particularly at the expansion joint (hereafter, EXPJ) between adjacent buildings. Because the EXPJ width in existing reinforced concrete buildings is usually very small, typically about 5 cm for school buildings in Japan, collision avoidance cannot be achieved by seismic retrofitting. This paper presents an experimental investigation into an effective method for reducing severe structural damage due to pounding at the EXPJ between narrowly separated buildings. The method involves inserting a shock‐absorbing material such as rubber into the EXPJ gap. The efficiency of the proposed method is evaluated by laboratory shaking tests using two model buildings. Furthermore, a lumped mass model is used to carry out a collision analysis in order to numerically investigate the influence of such a shock‐absorbing material. Both the numerical and experimental results confirm the effectiveness of the proposed approach. The validity of the proposed method is also demonstrated by numerical simulation of adjacent 10‐story steel buildings with an EXPJ width of 5 cm. The force, acceleration and velocity produced by earthquake‐induced structural pounding are found to be remarkably mitigated by inserting a soft shock‐absorbing material into the EXPJ gap. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
10.
11.
Longitudinal vibrations of concrete-faced rockfill dams may cause significant compressive stresses and joint openings in the slab panels. The behavior of such dams subjected to longitudinal and vertical vibrations is investigated, based on numerical simulation of the staged construction, reservoir impoundment and seismic shaking. The static analysis uses a hyperbolic model for the rockfill, whereas the seismic analysis uses a nonlinear hysteretic model which accounts for the dynamic properties. A damage plasticity model is used for the reinforced concrete and frictional contact behavior is considered at the base and vertical sides of the concrete panels. The seismic analysis takes into account the flexibility of the canyon rock and potential dynamic rockfill settlements. An existing 150 m–high dam is used to investigate the effect of longitudinal vibrations on the compressive stresses near the slab-to-slab vertical interfaces and the opening of the joints. The effect of dynamic settlements is examined and comparisons are made to the response from upstream/downstream and combined vibrations. The effectiveness of introducing 5 cm-wide cuts at selected vertical joints to reduce slab compression in existing CFRDs is demonstrated. The presented results offer useful insight into the effect of longitudinal vibrations on the seismic behavior of CFRDs. 相似文献
12.
本文采用振动台子结构试验数值仿真验证了圆柱形调谐液体阻尼器(CTLD)控制建筑结构地震响应的性能。振动台子结构试验将结构模型作为数值子结构在计算机中计算,将CTLD作为试验子结构进行物理试验。在CTLD和振动台之间安装剪切力检测装置,将测得的剪切力和地震波输入到数值子结构中,采用实时子结构中心差分法进行数值子结构运动方程的求解,计算得到了结构顶层的绝对加速度。再将加速度由振动台实时加载到试验子结构上,实现了结构和CTLD的相互作用。对一个单自由度结构有CTLD控制和无CTLD控制时的加速度响应进行了精确数值求解,结果验证了CTLD能够有效地控制结构在地震作用下的加速度响应。用振动台子结构试验对CTLD与结构耦合系统进行仿真,得到的加速度响应与精确数值求解的结果吻合较好,验证了这种方法能够准确地评估CTLD的减振性能。 相似文献
13.
Experimental and analytical study on the performance of particle tuned mass dampers under seismic excitation 下载免费PDF全文
下载免费PDF全文 A particle tuned mass damper (PTMD), which is a creative integration of a traditional tuned mass damper and an efficient particle damper in the vibration control area, is proposed. This paper presents a comprehensive study that involves experimental, analytical, and computational approaches. The vibration control effects of a PTMD that is attached to a five‐story steel frame under seismic input are investigated by a series of shaking table tests. The influence of some parameters (auxiliary mass ratio, gap clearance, mass ratio of particles to the total auxiliary mass, frequency characteristics, and amplitude level of the input) is explored, and the performance of the PTMD with/without buffered material is compared. The experimental results show that the PTMD can achieve significant damping effects under seismic excitations, and the bandwidth of the suppression frequency is expanded, showing the device's robustness and control efficiency. In addition, an approximately analytical solution that is based on the concept of an equivalent single‐particle damper is presented, and the method to determine the corresponding system parameters is introduced. A comparative study between experimental and numerical results is conducted to verify the feasibility and accuracy of this analytical model. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
14.
A series of large‐scale dynamic tests was conducted on a passively controlled five‐story steel building on the E‐Defense shaking table facility in Japan to accumulate knowledge of realistic seismic behavior of passively controlled structures. The specimen was tested by repeatedly inserting and replacing each of four damper types, that is, the buckling restrained braces, viscous dampers, oil dampers, and viscoelastic dampers. Finally, the bare steel moment frame was tested after removing all dampers. A variety of excitations was applied to the specimen, including white noise, various levels of seismic motion, and shaker excitation. System identification was implemented to extract dynamic properties of the specimen from the recorded floor acceleration data. Damping characteristics of the specimen were identified. In addition, simplified estimations of the supplemental damping ratios provided by added dampers were presented to provide insight into understanding the damping characteristics of the specimen. It is shown that damping ratios for the specimen equipped with velocity‐dependent dampers decreased obviously with the increasing order of modes, exhibiting frequency dependency. Damping ratios for the specimen equipped with oil and viscoelastic dampers remained constant regardless of vibration amplitudes, whereas those for the specimen equipped with viscous dampers increased obviously with an increase in vibration amplitudes because of the viscosity nonlinearity of the dampers. In very small‐amplitude vibrations, viscous and oil dampers provided much lower supplemental damping than the standard, whereas viscoelastic dampers could be very efficient. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
15.
滑移摩擦隔震系统在多向地面运动作用下的试验研究 总被引：7，自引：2，他引：7
基础隔震通常只考虑隔离水平地面运动，而对竖向地面运动的影响注意不够，本文进行了滑移摩擦隔震系统的振动台房屋模型试验，研究多向地面运动输入时上部结构反应和隔震系统的性能，试验中分别对模型输入了不同方向的地震动，其中包括水平单向、水平双向、水平和竖向及三向地震动输入，对试验结果进行了分析比较，结果表明竖向地震动输入对上部结构的水平地震反应有显著影响，同时在橡胶隔震支座中产生了竖向拉力。 相似文献
16.
This paper proposes the use of the nonlinear restoring force in an isolation system to improve the performance of a seismic isolator. Nonlinear magnetic springs applied to guideway sliding isolators (GSI) that protect precision machinery against seismic motion were studied. The magnetic springs use a non‐contact magnetic repulsion force to achieve a nonlinear property. A numerical simulation model of the GSI system using step‐by‐step integration in the time domain was developed. A full‐scale shaking table test was performed to verify the accuracy of the numerical model. Simulation and experimental results show that the GSI system with magnetic springs has good performance when subjected to floor vibrations during earthquakes. A parametric analysis of the magnetic springs in the GSI system under seismic motion was theoretically investigated. It was found that sufficient magnetic forces can diminish the system relative displacements. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
17.
Chin‐Hsiung Loh Jerome P. Lynch Kung‐Chun Lu Yang Wang Chia‐Ming Chang Pei‐Yang Lin Ting‐Hei Yeh 《地震工程与结构动力学》2007,36(10):1303-1328
The performance aspects of a wireless ‘active’ sensor, including the reliability of the wireless communication channel for real‐time data delivery and its application to feedback structural control, are explored in this study. First, the control of magnetorheological (MR) dampers using wireless sensors is examined. Second, the application of the MR‐damper to actively control a half‐scale three‐storey steel building excited at its base by shaking table is studied using a wireless control system assembled from wireless active sensors. With an MR damper installed on each floor (three dampers total), structural responses during seismic excitation are measured by the system's wireless active sensors and wirelessly communicated to each other; upon receipt of response data, the wireless sensor interfaced to each MR damper calculates a desired control action using an LQG controller implemented in the wireless sensor's computational core. In this system, the wireless active sensor is responsible for the reception of response data, determination of optimal control forces, and the issuing of command signals to the MR damper. Various control solutions are formulated in this study and embedded in the wireless control system including centralized and decentralized control algorithms. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
18.
A seismic shaking‐table test performed on a one‐storey steel frame with an 8 ton RC floor slab was reproduced on a similar specimen by means of the pseudo‐dynamic (PsD) method. A satisfactory agreement of the results could only be achieved after recalibration of the theoretical mass in the PsD equation and proper inclusion in the PsD test input of the horizontal and pitching accelerations measured on the table. In the shaking‐table test, the spurious pitching motion produced a significant increase in the apparent damping that could be estimated as a function of the pitching dynamic flexibility of the system. Dynamic and PsD snap‐back tests were also performed to provide an additional check of the reliability of the PsD method. The spurious pitching motion of the shaking table should always be measured during the tests and reported as a mean to increase the reliability and usefulness of the results. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
19.
A full-scale, two-story, two-by-one bay, steel braced-frame was subjected to a number of unidirectional ground motions using three shake tables at the UNR-NEES site. The test-bed frame was designed to study the seismic performance of nonstructural systems including steel-framed gypsum partition walls, suspended ceilings and fire sprinkler systems. The frame can be configured to perform as an elastic or inelastic system to generate large floor accelerations or large inter story drift, respectively. In this study, the dynamic performance of the linear and nonlinear test-beds was comprehensively studied. The seismic performance of nonstructural systems installed in the linear and nonlinear test-beds were assessed during extreme excitations. In addition, the dynamic interactions of the test-bed and installed nonstructural systems are investigated. 相似文献
20.
地震作用下隔震简支梁桥碰撞反应的振动台试验 总被引：2，自引：0，他引：2
由地震引发的碰撞是影响桥梁地震反应以及造成桥梁破坏的重要因素。本文对地震作用下隔震简支梁桥的碰撞反应进行了振动台试验。设计制作1个两跨简支的隔震梁桥模型,试验研究了梁间隙、邻梁质量比、隔震支座类型等参数对桥梁碰撞反应的影响。试验结果表明邻梁间隙、邻梁质量比、隔震支座类型等参数对桥梁的碰撞反应有着显著的影响。邻梁间隙越大,碰撞次数越少;邻梁质量比越大,撞击力越大。铅芯橡胶支座比板式橡胶支座耗能能力更强,可以有效降低邻梁之间的撞击力甚至避免碰撞发生。从而为桥梁防碰撞设计提供了可靠的试验依据。 相似文献