共查询到20条相似文献，搜索用时 46 毫秒
1.
2.
3.
4.
浅海悬沙浓度观测方法的对比研究 总被引：4，自引：0，他引：4
在动力和沉积条件复杂的浅海海域获取水-体的悬沙浓度有多种方法,目前较先进的主要是声学和光学浊度测量方法,但均需通过现场采集水样进行浊度标定;水样的分析方法主要有抽滤法和沉淀干燥法。根据2010年3—4月在厦门九龙江口获取的光学(OBS、LISST-100X)和声学(ADCP、ADP和ADV)浊度数据,以及现场同步水样,对这两种获取悬沙浓度的方法进行了比较;2011年2—3月在长江口北支获取水样,分别使用抽滤法和沉淀干燥法获取悬沙浓度数据进行比对分析。结果表明,声学和光学方法都具有较高的精度,在同一观测层位,光学与声学仪器的相对误差均较小;由于声波在水体中传播距离较远,声学方法可获得沿水深的整个剖面的信息,因而比光学仪器具有更高的空间分辨率和测量范围。对比发现,抽滤法获得的悬沙浓度数值略低于沉淀干燥法获得的结果,可能与沉淀干燥法难以洗净盐分有关。 相似文献
5.
潮间带水沙多层位同步测量系统应用的初步研究 总被引：2，自引：0，他引：2
利用水压、光电转换原理研制成的多层位水沙同步测量系统(WCT系统)不仅可测量潮间带水位随时间的变化系列、同一层位的浊度及流速，还可以同步观测这些参数在潮间带水流剖面不同层位上的变化。野外对比试验表明，WCT系统获得的流速值与直读式流速仪的测量结果基本一致，平均相对误差为14．52％；悬沙传感器经野外现场率定获得悬沙浓度，平均相对误差为21．96％，精度比室内率定提高—倍以上。悬沙粒径是影响悬沙浓度测量精度的主要因素。此外，自然环境(如海水温盐度)的变化及仪器本身的特性也可能影响到测量结果。因此，WCT系统在潮间带的水位、流速和悬沙浓度的观测和边界层研究方面有相当潜力。 相似文献
6.
水体悬沙浓度是水利、环境、河口海岸与海洋相关研究领域最为基础的数据需求之一。随着传感器技术的发展, 悬沙浓度连续测量技术在悬沙浓度测量领域表现出高时空分辨率、长期数据采集的成本和风险均较低的突出优点。本文综述了光学、声学、音叉谐振、压差和放射性射线衰减等原理用于悬沙浓度连续测量技术的相关研究进展, 探讨了各技术方法的优、缺点, 并提出了今后的研发重点和发展方向主要在以下几个方面: 1) 光后向散射原理是低成本、小型化和高时频测量悬沙浓度的最优技术路线, 需着力于开展量程扩增和粒径敏感度削弱研究; 2) 低不确定度悬沙浓度垂向剖面观测的实现依赖于超声后向散射原理技术路线的发展; 3) 音叉谐振原理技术路线尤为契合高含沙水流和浮泥工况下的超高量程应用场景; 4) 多技术路线传感器融合以及使用人工智能算法模型替代正向反演模型。 相似文献
7.
OBS浊度标定与悬沙浓度误差分析 总被引：2，自引：0，他引：2
利用光学后向散射浊度计OBS-3A,在长江河口南槽进行大小潮周期连续观测。利用OBS室内和现场浊度标定,计算不同潮时OBS观测悬沙浓度相对误差,并对影响其观测精度因素进行分析。主要结果有:(1)现场OBS标定R值比室内标定偏低,但也在0.8以上;(2)大潮平均相对误差值变化比小潮大,在悬沙浓度低于1.5kg/m3条件下,大小潮悬沙浓度平均相对误差都在15%以下;(3)悬沙粒径大小是影响OBS观测精度的主要因素,生物、泥沙颜色、水色和水中气泡等因素也对观测结果产生一定影响。 相似文献
8.
9.
ADCP测量悬沙浓度的可行性分析与现场标定 总被引：18，自引：3，他引：18
根据现场观测数据，对ADCP测量悬浮沙浓度的进行标定实验。结果表明，在观测期间悬沙粒径变化较小的条件下，后散射强度与水样悬沙浓度之间存在较好的相关性。悬沙浓度剖面标定公式中的参数C′可用剖面实测水样浓度来确定，该参数与浓度密切相关：同一剖面不同浓度之间有一定的波动，但同一浓度不同潮时的变化很小。使用同一剖面参数C′的平均值计算出的剖面悬沙分布误差较大（29％－43％），而按不同深度段分别标定，误差可以小于20％，能够满足沉积动力学研究的需要。 相似文献
10.
近底层悬沙时空变化对于理解河口冲淤变化有着至关重要的作用。然而,长期以来河口近底层水体悬沙浓度的连续变化大都是基于单点观测数据或水样处理获取。基于此,本研究利用光学仪器边界层悬浮物剖面测量仪(Argus Surface Meter IV,ASM-IV)获得长江口南槽近底层进行连续10 d的实测数据,探讨ASM-IV仪器监测悬沙浓度精度的有效性。结果表明:(1)传统仪器布设方法所获取的数据,相对误差高于基于ASM-IV所测误差,在大、中及小潮期间的平均误差值分别为24.15%、17.31%和16.18%;越靠近底部河床,相对误差从距底52 cm向下随距底距离的减小而逐渐增大;(2)对于近底层单宽悬沙通量测量结果而言,传统测量仪器布设方法所测量数值一般偏小;(3)大潮时期近底层1 m内的水体悬沙分布均匀,分层不明显;在中、小潮时期,与近底层1 m内平均悬沙浓度相差最大的点皆位于距底20~50 cm附近。因而,近底层悬沙浓度测量时间在大潮时期或越靠近底层,利用ASM-IV监测近底层悬沙浓度值更为准确。中、小潮时期利用单点或采集水样测量时,选取0.8H层水体悬沙浓度代替近底层悬沙浓度较最底部水体悬沙浓度更为准确。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.