共查询到20条相似文献，搜索用时 15 毫秒
1.
Three-dimensional surface crack initiation and propagation in two kinds of heterogeneous rocks were numerically investigated via parallel finite element analysis using a supercomputer. Numerically simulated rock specimens containing a pre-existing flaw were subjected to uniaxial compression until failure. The initiation and propagation of wing cracks, anti-wing cracks, and shell-like cracks were reproduced by numerical simulations. The numerically simulated results demonstrate that the further propagation of wing cracks and shell-like cracks stop due to their wrapping (curving) behavior in three-dimensional spaces, even if the applied loads continue to increase. Furthermore, rock heterogeneity could significantly influence crack propagation patterns and the peak uniaxial compressive strengths of rock specimens. Moreover, anti-wing cracks only appeared in relatively heterogeneous rocks, and the peak uniaxial compressive strengths of the specimens were observed to depend on the inclination of the pre-existing flaw. Finally, the mechanism of surface crack propagation is discussed in the context of numerically simulated anti-plane loading tests, wherein it was identified that Mode III loading (anti-plane loading) does not lead to Mode III fracture in rocks due to their high ratio of uniaxial compressive strength to tensile strength. This finding could explain the lateral growth of an existing flaw in its own plane, which is a phenomenon that has not been observed in laboratory experiments. 相似文献
2.
岩石裂纹的扩展是一个经典的不连续问题,常规有限元方法难以实现裂纹扩展过程的仿真模拟。扩展有限元法(XFEM)实现了计算网格与不连续面相互独立,因此模拟移动的不连续面时无需对网格进行重新剖分。本文介绍了XFEM基本原理和岩石断裂力学常用判据,尝试对岩石类材料单缝Ⅰ型三点弯曲、单缝剪切和双缝平板实验进行模拟。分析结果表明:扩展有限元模拟岩石类材料断裂问题不受网格划分限制,裂纹以实际应力场分布随机扩展;直观地给出岩样的微裂纹产生、演化,直至完全破坏的全过程,并与实验结果吻合。该方法能够应用到岩石断裂力学方面的研究,模拟岩石类材料的宏细观破坏过程,为解决复杂问题提供了方便的途径。 相似文献
3.
为研究三点弯曲梁在荷载作用下的破坏模式,采用颗粒流程序PFC2D对含不同位置和高度的预置裂隙的三点弯曲
梁破坏过程进行了模拟。结果表明：预制裂隙的长度与位置共同影响梁的破坏;当预置裂隙的位置离加载点较远时,主
要是预置裂隙的高度对梁的破坏产生影响,当裂隙高度超过70 mm时,试件的破坏模式发生变化;当预置裂隙高度一定
时,预置裂隙的位置是试件发生破坏的主要影响因素,当距离支撑点的距离超过100 mm时,试件的破坏模式发生了改
变;试件的破坏过程伴随着能量的积累和释放。相比较于有限元法和有限差分法,离散元法能更好的模拟出材料裂隙产
生和发展的过程。 相似文献
4.
为研究三点弯曲梁在荷载作用下的破坏模式，采用颗粒流程序PFC2D对含不同位置和高度的预置裂隙的三点弯曲
梁破坏过程进行了模拟。结果表明：预制裂隙的长度与位置共同影响梁的破坏；当预置裂隙的位置离加载点较远时，主
要是预置裂隙的高度对梁的破坏产生影响，当裂隙高度超过70 mm时，试件的破坏模式发生变化；当预置裂隙高度一定
时，预置裂隙的位置是试件发生破坏的主要影响因素，当距离支撑点的距离超过100 mm时，试件的破坏模式发生了改
变；试件的破坏过程伴随着能量的积累和释放。相比较于有限元法和有限差分法，离散元法能更好的模拟出材料裂隙产
生和发展的过程。 相似文献
5.
A two-dimensional brittle creep model for rock provides insight into the initiation of shear fracture along weak discontinuities in rock. The model accounts for material heterogeneity and introduces the concept of a mesoscopic renormalization to capture the cooperative interaction between cracks in the transition from distributed to localized damage. A series of shear creep tests on rock with discontinuities were performed to simulate the initiation and propagation of crack along a pre-existing weakness under sustained shear stress and normal stress. The investigation showed that shear stress level and the normal stress level might have significant effect on the long-term behavior of rock with weak discontinuities. Moreover, a case study of rock slope instability was also investigated, where the numerically simulated instability failure of rock slope with discontinuities showed that both tensile and shear damage at the weakest elements are the trigger for the failure surface initiation in the rock slope. Once damage occurs, redistributed stress concentrations would then intensify fracture propagation and coalescence within these damage zones, leading to the progressive development of a failure surface. Moreover, failure surface extending is not only dominated by the properties and the position of discontinuities but also influenced remarkably by the complex interaction between existing discontinuities and fracture propagation. The results are of general interest because they can be applied to the investigation of time-dependent instability in rock masses, to the mitigation of associated rock hazards in rock engineering, and even to a better understanding of the physical phenomena governing the stability of rock slope. 相似文献
6.
危岩是三峡库区典型的地质灾害类型之一,而主控结构面受荷断裂扩展是危岩发育成灾的关键核心。将危岩主控结构面类比为宏观裂纹,利用扩展有限元法在模拟裂纹扩展方面的优势,基于考虑裂纹面水压力作用的虚功原理推导出了采用扩展有限元法分析水力劈裂问题的控制方程,给出了危岩主控结构面水力劈裂问题的扩展有限元实现方法,对重庆万州太白岩危岩主控结构面的水力劈裂进行了数值模拟分析。计算结果表明：暴雨是威胁危岩稳定性的最敏感因素,随着裂隙水压力上升,裂端拉应力会急剧升高,危岩的稳定性降低;I型裂纹扩展是危岩主要的结构面扩展形式,结构面一旦发生开裂,将处于非稳定扩展状态。 相似文献
7.
Jiao Kaituo Han Dongxu Wang Daobing Chen Yujie Li Jingfa Gong Liang Bai Bofeng Yu Bo 《Computational Geosciences》2022,26(5):1167-1187
Thermal-hydro-mechanical (THM) coupled fracture propagation is common in underground engineering. Rock damage, as an inherent property of rock, significantly affects fracture propagation, but how it influences the THM coupled fracturing remains stubbornly unclear. A pore-scale THM coupling model is developed to study this problem, which combines the lattice Boltzmann method (LBM), the discrete element method (DEM), and rock damage development theory together for the first time. This model can more accurately calculate the exchanged THM information at the fluid-solid boundary and fluid conductivity dependent on fracture and rock damage. Based on the developed model, the synergistic effect of injected temperature difference (fluid temperature below rock temperature) and rock damage (characterized by the parameter “critical fracture energy”, abbreviated as “CFE”) on fracture propagation of shale are investigated particularly. It is found that: (1) the generation of branched cracks is closely related to the temperature response frontier, and the fracture process zone of single bond failure increases in higher CFE. (2) through the analysis of micro failure events, hydraulic fracturing is more pronounced in the low CFE, while thermal fracturing displays the opposite trend. The fluid conductivity of fractured rock increases with a higher injected temperature difference due to the more penetrated cracks and wider fracture aperture. However, this enhancement weakens when rock damage is significant. (3) in the multiple-layered rock with various CFEs, branched cracks propagating to adjacent layers are more difficult to form when the injection hole stays in the layer with significant rock damage than without rock damage.
相似文献8.
Two-dimensional finite element model was created in this work to investigate the stress distribution within rock-like samples
with offset open non-persistent joints under uniaxial loading. The results of this study have explained the fracture mechanisms
observed in tests on rock-like material with open non-persistent offset joints (Mughieda and Alzo’ubi, Geotech Geol Eng J
22:545–562, 2004). Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-noded
isoperimetric plain strain element with two degrees of freedom per node, and the three-noded constant strain triangular element
with two degree of freedom per node were used in the present study. The results of the present study showed that the tensile
stress in the bridge area caused coalescence for specimens with overlapped preexisting cracks (joints) while the coalescence
of the secondary cracks, due to shear stress, caused the failure of specimens with non-overlapping cracks. 相似文献
9.
Micromechanical Model for Simulating the Fracture Process of Rock 总被引：25，自引：3，他引：25
Summary A micromechanical model is proposed to study the deformation and failure process of rock based on knowledge of heterogeneity of rock at the mesoscopic level. In this numerical model, the heterogeneity of rock at the mesoscopic level is considered by assuming the material properties in rock conform to the Weibull distribution. Elastic damage mechanics is used to describe the constitutive law of meso-level elements, the finite element method is employed as the basic stress analysis tool and the maximum tensile strain criterion as well as the Mohr-Coulomb criterion is utilized as the damage threshold. A simple method, similar to a smeared crack model, is used for tracing the crack propagation process and interaction of multiple cracks. Based on this model, a numerical simulation program named Rock Failure Process Analysis Code (RFPA) is developed. The influence of parameters that include the Weibull distribution parameters, constitutive parameters of meso-level elements and number of elements in the numerical model, are discussed in detail. It is shown that the homogeneity index is the most important factor to simulate material failure with this model. This model is able to capture the complete mechanical responses of rock, which includes the crack patterns associated with different loading stages and loading conditions, localization of deformation, stress redistribution and failure process. The numerical simulation of rock specimens under a variety of static loading conditions is presented, and the results compare well with experimental results. 相似文献
10.
A simplified computational technique based on a refined global–local method is applied to the failure analysis of concrete structures. The technique distinguishes the scale of the structure, modelled with large size finite elements, from the scale at which material non‐linearity occurs due to progressive cracking and macro‐crack propagation. The finite element solution is split into two parts: a linear elastic analysis on a coarse mesh over the entire structure and a non‐linear analysis over a small part of the structure where a dense finite element grid is employed. In the non‐linear calculation, a non‐local damage model is implemented. These two computations are coupled with the help of an iterative scheme. The size and location of the region where a non‐linear analysis is performed, is adapted to follow the development of the damage zone. Numerical examples of mode I fracture of concrete specimens with straight and curved cracks are presented. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
11.
开发一种改进损伤框架的粒子流算法,被称为核断裂的光滑粒子流法（kernel-broken smoothed particle hydrodynamics,KBSPH）,用于模拟地震条件下岩质边坡的裂纹扩展和变形破坏过程.在KBSPH中,提出一种改进的损伤框架,通过引入断裂标志来改进损伤粒子的核函数,使损伤粒子的虚拟应力键直接断裂,裂纹在断裂的应力键间生成,从而模拟岩石的裂纹扩展过程.在地震边界上采用了双层边界,将动力输入边界与黏滞边界分离.首先通过薄板振动实验验证KBSPH的动力特性.其次以单裂隙岩体单轴压缩试验验证KBSPH的断裂力学特性.最后模拟地震条件下多节理岩质边坡中裂纹扩展过程和动力响应.薄板振动实验验证了KBSPH的动力特性的准确性.单裂隙岩体单轴压缩试验,证明了KBSPH可以正确模拟预制裂隙尖端的翼型裂纹.通过对比以往数值模拟方法和现场案例,表明KBSPH正确揭示了加速度放大效应以及地震条件下岩质边坡的裂纹扩展过程.KBSPH避免了传统算法的网格畸变,损伤粒子应力分量重新分配的问题,降低了编程难度,提高了运行速率,可为SPH在地震条件下岩石力学中的应用和理解岩石断裂机理提... 相似文献
12.
Coupled hydromechanical‐fracture simulations of nonplanar three‐dimensional hydraulic fracture propagation 
下载免费PDF全文
下载免费PDF全文 This paper presents an algorithm and a fully coupled hydromechanical‐fracture formulation for the simulation of three‐dimensional nonplanar hydraulic fracture propagation. The propagation algorithm automatically estimates the magnitude of time steps such that a regularized form of Irwin's criterion is satisfied along the predicted 3‐D fracture front at every fracture propagation step. A generalized finite element method is used for the discretization of elasticity equations governing the deformation of the rock, and a finite element method is adopted for the solution of the fluid flow equation on the basis of Poiseuille's cubic law. Adaptive mesh refinement is used for discretization error control, leading to significantly fewer degrees of freedom than available nonadaptive methods. An efficient computational scheme to handle nonlinear time‐dependent problems with adaptive mesh refinement is presented. Explicit fracture surface representations are used to avoid mapping of 3‐D solutions between generalized finite element method meshes. Examples demonstrating the accuracy, robustness, and computational efficiency of the proposed formulation, regularized Irwin's criterion, and propagation algorithm are presented. 相似文献
13.
对含预制裂纹的花岗岩进行单轴压缩试验研究预制裂纹倾角α对脆性岩石渐进性破坏过程的影响。首先埘破坏过程的轴向应力-横向应变曲线进行总结和讨论,然后分析预制裂纹与加载方向夹角α埘岩石的应应力门槛值：裂纹起始应力σci、裂纹扩展应力σed、峰值强度矿σf,由应变片记录的应力-应变曲线和试样的表嘶裂纹扩展情况的影响机制。结果表明,含有预制裂纹的岩石试样进行加载试验过程中,顶制裂纹倾角α的变化成了决定脆性岩石破裂办式的主要因素。故在对含节理、裂隙的脆性岩石的工程应用上,通过对岩休的轴向应力-横向应变向应变典线进行分析,可以对地下开挖工程起到指导设计开挖方式及支护形式的作用。 相似文献
14.
Numerical Simulation of 3D Hydraulic Fracturing Based on an Improved Flow-Stress-Damage Model and a Parallel FEM Technique 总被引：4，自引：4，他引：0
L. C. Li C. A. Tang G. Li S. Y. Wang Z. Z. Liang Y. B. Zhang 《Rock Mechanics and Rock Engineering》2012,45(5):801-818
The failure mechanism of hydraulic fractures in heterogeneous geological materials is an important topic in mining and petroleum engineering. A three-dimensional (3D) finite element model that considers the coupled effects of seepage, damage, and the stress field is introduced. This model is based on a previously developed two-dimensional (2D) version of the model (RFPA2D-Rock Failure Process Analysis). The RFPA3D-Parallel model is developed using a parallel finite element method with a message-passing interface library. The constitutive law of this model considers strength and stiffness degradation, stress-dependent permeability for the pre-peak stage, and deformation-dependent permeability for the post-peak stage. Using this model, 3D modelling of progressive failure and associated fluid flow in rock are conducted and used to investigate the hydro-mechanical response of rock samples at laboratory scale. The responses investigated are the axial stress–axial strain together with permeability evolution and fracture patterns at various stages of loading. Then, the hydraulic fracturing process inside a rock specimen is numerically simulated. Three coupled processes are considered: (1) mechanical deformation of the solid medium induced by the fluid pressure acting on the fracture surfaces and the rock skeleton, (2) fluid flow within the fracture, and (3) propagation of the fracture. The numerically simulated results show that the fractures from a vertical wellbore propagate in the maximum principal stress direction without branching, turning, and twisting in the case of a large difference in the magnitude of the far-field stresses. Otherwise, the fracture initiates in a non-preferred direction and plane then turns and twists during propagation to become aligned with the preferred direction and plane. This pattern of fracturing is common when the rock formation contains multiple layers with different material properties. In addition, local heterogeneity of the rock matrix and macro-scale stress fluctuations due to the variability of material properties can cause the branching, turning, and twisting of fractures. 相似文献
15.
对预制交叉裂隙岩石试样进行裂纹扩展试验,研究了裂纹萌生、扩展、聚合过程,分析了主裂隙和轴向载荷夹角及主次裂隙夹角对裂纹起裂应力和聚合应力的影响,并用混合有限元-离散元程序,即图形处理器并行化的3D Y-HFDEM代码对试验进行了仿真计算,实现了岩石破坏从连续介质向非连续介质的过渡,对裂纹类及损伤破坏模式进行了识别,捕捉到了试验中难以发现的现象。研究表明：随主裂隙与轴向载荷夹角增加,裂纹聚合区的拉伸裂纹数量增加;裂纹起裂和聚合应力与主裂隙与轴向载荷夹角成正比;主次裂隙夹角增加,岩石的破坏模式由拉伸破坏转为剪切破坏,交叉裂隙加剧岩石破碎程度;主裂隙尖端萌生扩展的拉伸-剪切混合裂缝引起的破坏在岩石破坏中占主导地位,是导致岩体失去承载能力的主控裂纹;混合有限元-离散元仿真软件GPGPU并行化的3D Y-HFDEM IDE在岩石裂纹扩展研究中具有优势,可以捕捉实验室难以发现的损伤断裂类型,可以作为岩石裂纹扩展研究的有力工具。 相似文献
16.
岩体内裂隙等非连续结构面对岩体的强度及变形等力学特性有着显著的影响,研究岩体裂隙起裂、扩展、相互作用和贯通机制,对工程岩体力学行为的表征和工程性能的评价十分重要。本文基于连续介质力学模型的离散元方法,通过考虑裂隙分布、模型加载条件及其与裂隙产状的关系,建立了一系列裂隙力学计算模型,研究了不同模型裂隙扩展演化特征和岩体破裂机制,分析了岩体裂隙扩展规律及其对岩体破坏路径和强度的影响,研究结果表明:（1）裂隙岩体模型加载条件下的破坏起裂点、最终贯通破坏特征及损伤分布受控于裂隙的产状及其与最大主压应力取向角度大小及围压大小。（2）裂隙弱面走向与最大主压应力取向斜交时,裂隙弱面在加载条件下其端部裂隙扩展、贯通破坏表现比较明显,反之,当裂隙弱面走向与最大主压应力取向一致时,裂隙弱面被动影响裂隙模型内新生裂隙的萌生、扩展和贯通模式,自身未出现新的扩展破坏。（3）裂隙数目的增多和围压的增大会显著增加模型内部剪切裂缝的数量和模型破坏后的破碎程度,模型内部的损伤区域主要围绕破裂面呈滑移线型交叉分布,非破裂面区域损伤呈条带状X型分布。（4）裂隙弱面走向与最大主压应力取向斜交时,裂隙对岩体模型强度的弱化程度高于裂隙弱面走向与最大主压应力取向一致的情况,而裂隙模型破坏后的残余强度则正好相反。 相似文献
17.
通过改进的PFC-FLAC离散−连续耦合计算方法,提出了一种基于FLAC连续模型耦合区域节点速率双线性插值的PFC颗粒流声发射片模拟方法以及基于声发射强度的围岩破坏区深度细观角度判别方法,并将其应用于地下厂房洞室开挖面、岩锚吊车梁与岩壁接触面等局部围岩损伤细观机制与破化特性研究。研究结果表明：浅层围岩接触力链逐渐稀疏,大量微裂纹发育并汇集成宏观裂隙,最终出现浅层破裂区,呈拉裂破坏;随着距离开挖面的增大,围岩从开挖前期受力较大产生破坏、到开挖后期只有少量微裂纹产生,对应了围岩回弹卸荷区深度。在岩壁围岩劣化和吊车梁超载的情况下,吊车梁与岩壁竖直接触面和倾斜接触面分别发育大量拉裂纹和剪裂纹,宏观表现为拉裂破坏与滑移破坏。上述分析结果与三维有限元方法相一致,并弥补了后者围岩破坏显示方法单一、难以描述围岩损伤程度变化的缺点,为研究地下厂房洞室大变形与应力集中部位的宏细观特性与损伤机制提供参考。 相似文献
18.
岩体内部赋存的裂隙很多表现为折线型,为探究这类岩体的断裂机制,制备含折线型裂隙砂岩试件并对其进行单轴压缩试验。采用数字图像相关(DIC)方法计算加载过程中的变形场演化,根据新生裂纹两侧的位移差异识别裂纹类型;运用扩展有限元法(XFEM)模拟断裂过程,根据应力分布特征解释翼型裂纹起裂与扩展机制。DIC计算结果表明,新生裂纹处出现应变局部化带,裂纹两侧发生相对分离;含直线型和折线型裂隙砂岩试件的翼型裂纹分别萌生于预制裂隙端部以及折角处,这是因为裂隙几何形态会改变拉应力集中位置;含折线型裂隙砂岩试件的起裂应力小于含直线型裂隙砂岩试件,这是因为相同加载条件下前者的最大拉应力值更大;这2类试件的裂纹扩展均是由于裂纹尖端集中的拉应力引起的,裂纹依然呈张开状态;裂隙几何形态未改变试件的最终破坏模式,均表现为对角剪切破坏。 相似文献
20.
随着扩展有限元理论的深入研究,利用扩展有限元方法模拟水力压裂具有了一定的可操作性。相比于常规有限元方法,XFEM方法具有计算结果精度高和计算量小的优点。但是,如何模拟射孔孔眼、如何模拟流体与岩石相互作用以及分析水力裂缝的扩展规律仍然是难题。以研究水力压裂裂缝扩展规律为目的,建立了岩石多孔介质应力平衡方程、流体渗流连续性方程和边界条件。通过有限元离散化方法对耦合方程矩阵进行处理。通过富集函数定义初始裂缝（射孔孔眼）,选择最大主应力及损伤变量D分别作为裂缝起裂和扩展判定准则,利用水平集方法模拟水力裂缝扩展过程。数值模拟结果显示：增加射孔方位角、压裂液排量和减小水平地应力差,起裂压力上升;黏度对起裂压力无明显影响。增加射孔方位角、压裂液排量、黏度和减小水平地应力差值有助于裂缝宽度的增加。增加水平地应力差值、压裂液排量和减小射孔方位角以及压裂液黏度有助于裂缝长度增加,反之亦然。基于ABAQUS的水力裂缝扩展有限元法可对不同井型和诸多储层物性参数及压裂施工参数进行分析,且裂缝形态逼真,裂缝面凹凸程度清晰,结果准确。此研究可作为一种简便有效研究水力压裂裂缝扩展规律的方法为油田水力压裂设计与施工提供参考与依据。 相似文献