共查询到17条相似文献，搜索用时 125 毫秒
1.
《中国海洋大学学报(自然科学版)》2017,(3)
采用三维非线性动态有限元方法对抛锚撞击海底管道进行模拟。建立霍尔锚模型,考虑管土相互作用,研究不同撞击能量下抛锚撞击管道的机械损伤(最大凹陷)变化规律。对不同防护措施的防护效果进行探讨,包括埋深、混凝土配重层、加大径厚比等措施。数值模拟结果与试验结果进行对比,两者结果吻合较好。结果表明:当锚与管道接触面积越小时,锚对管道的撞击凹陷越大;加大埋深对抛锚撞击管道有很好防护的作用;管道内压对抛锚撞击管道有一定的抵抗作用;混凝土配重层对防护抛锚撞击管道的防护作用不明显;增加管道壁厚是防护抛锚撞击管道的有效措施之一,也应考虑经济性。本文研究结果为实际工程中降低抛锚撞击管道机械损伤后果提供参考。 相似文献
2.
《中国海洋大学学报(自然科学版)》2020,(Z1)
基于ANSYS/LS-DYNA有限元软件显示动力分析,采用非线性动态有限元法,对海底管道受坠物碰撞的动态过程进行数值模拟,对比分析坠物质量、坠物形状、轴向预加荷载因素对海底管道在撞击作用下凹陷及损伤区域的影响。结果表明:海底管道受撞击部位的凹陷及损伤区域随着坠物能量的增加而增大;坠物形状因素由于碰撞发生时接触面不同对管道凹陷及损伤区域造成不同的影响;海底管道内压的存在一定程度上抵抗了碰撞造成的局部塑性损伤变形;轴向受拉对海底管道损伤方面的影响很小可忽略不计;适当增加轴向压力可提升海底管道抗碰撞冲击能力而过大的轴向压力会加剧管道破坏。 相似文献
3.
基于ANSYS/LS-DYNA动力学分析软件,采用非线性动力有限元法,对坠物撞击海底管道的过程进行数值仿真。通过大量的数值模拟得出:相同坠落物能量的情况下,悬空管道的凹陷损伤深度与裸露管道的相比偏小,且随着坠落物能量的增加,其差值增大;随着坠落物速度、坠落物质量的增大,管道撞击部位凹陷变形加剧,海底管道悬空段的最大振动幅值增大;相同坠落物能量的情况下,坠落物与悬空管道的接触面积越小,悬空管道的损伤深度越大;海床土体参数(剪切弹性模量、内摩擦角、密度)的变化对悬空管道的凹陷损伤深度及悬空段的最大振动幅值的影响较小。 相似文献
4.
《海洋通报(英文版)》2015,(2)
基于ANSYS/LS-DYNA动力学分析软件,采用非线性动力有限元法,对坠物撞击海底管道的过程进行数值仿真。通过大量的数值模拟得出:相同坠落物能量的情况下,悬空管道的凹陷损伤深度与裸露管道的相比偏小,且随着坠落物能量的增加,其差值增大;随着坠落物速度、坠落物质量的增大,管道撞击部位凹陷变形加剧,海底管道悬空段的最大振动幅值增大;相同坠落物能量的情况下,坠落物与悬空管道的接触面积越小,悬空管道的损伤深度越大;海床土体参数(剪切弹性模量、内摩擦角、密度)的变化对悬空管道的凹陷损伤深度及悬空段的最大振动幅值的影响较小。 相似文献
5.
基于非线性有限元分析软件ANSYS/LS-DYNA建立海底悬空管道受坠物撞击的三维模型,考虑接触、摩擦和管土耦合作用,模拟海底悬空管道受坠物撞击的动态响应过程。通过大量的数值模拟,对比分析撞击能量、撞击角度以及坠物与管道间的摩擦对海底悬空管道受撞击部位凹陷损伤的影响。结果表明:管道受撞击部位的凹陷损伤随撞击能量的增大而变大;坠物撞击角度越大,管道受撞击部位的凹陷损伤越大;坠物与管道之间的摩擦使管道受撞击部位凹陷损伤略微增大,但影响很小。 相似文献
6.
采用当地海床的天然粉沙进行试验床面的设计,对海底管道在实际海床受到的极限波浪和最大水流作用进行试验,在管道上方铺设混凝土联锁排,对联锁排块体稳定性和其对管道防护的有效性进行研究。通过物理模型试验,研究了在极限波浪和最大水流作用下,管道在粉沙床面最大冲刷深度。通过不同水深中波流条件下研究了混凝土联锁排防护效果及其周围床面的冲刷变化,观测了联锁排的稳定性。试验结果表明:按半经验半理论简化公式得出的联锁排厚度能满足稳定性的要求,比水利部规范计算的联锁排厚度偏大的公式更加适合应用,试验期间混凝土联锁排的排面稳定,能有效保护管道,在该防护下管道没有冲刷,只在联锁排上下游与床面接触的来流段和尾端有冲刷,但该冲刷深度不影响联锁排整体的稳定性。 相似文献
7.
8.
为探索海底管道在锚击作用下的损伤规律,通过海底管道损伤试验和数值模拟,研究了坠物质量、坠落高度和坠物形状对海底管道机械损伤的影响,并结合试验结果修正了Ellinas-Wallker公式。研究结果表明:管道的凹陷损伤随坠物质量和坠落高度的增大而变大;在相同质量的立方体、球体和模型锚三种形状坠物作用下,球体坠物对管道的损伤最严重;EllinasWallker公式计算结果偏于保守,修正后计算结果与试验和数值模拟结果吻合良好。研究结果可以为海底管道的工程设计及应用提供一定的参考。 相似文献
9.
10.
11.
海底电缆穿越底质坚硬海床时,覆盖混凝土联锁排可以有效保护海缆。根据国网舟山500 kV海底输电电缆所在海域实测水文数据,采用力学平衡公式和数值模拟两种计算方法,研究混凝土块在极端水流作用下的在位稳定性。基于推导出的力学平衡公式,对其进行函数分析后发现,当混凝土块底边固定时,存在一个极值高度,此时铺设在海床的混凝土块最为稳定,可以抵挡的水流流速最大。通过数值模拟,研究了混凝土联锁排在水流作用下的三维流态特征,对不同形状混凝土块的受力情况进行比较后发现,当混凝土块边缘为圆角时,可以改变边缘周边的水流结构,总体上加强混凝土块的稳定性。经计算,尽管国网舟山500 kV海底输电电缆所在的灰鳖洋海域潮流流速较大,但常规长、宽、高为0.4 m×0.4 m×0.3 m的块体组成的混凝土联锁排可以抵抗水流的冲击,保护海底电缆。 相似文献
12.
由于海床起伏不平,斜坡的存在必然改变波浪对管线及海床的作用特性,进而影响管线三维冲刷。基于波浪港池实验,考虑规则波的作用,采用中值粒径为0.22mm的原型沙铺设与波浪传播方向成45°夹角的斜坡,研究斜向波作用下斜坡上海底管线的三维冲刷特性。通过测量管线下方冲刷坑宽度和深度的差异,分析管线三维冲刷的不均衡性。实验表明:管线的存在使斜坡上的波高有所降低;斜向波作用下管线三维冲刷的不均衡性表现为深度不均衡性和宽度不均衡性,宽度不均衡性主要是管后淤积泥沙的后移引起的,周期对三维冲刷不均衡性的影响比波高对其的影响程度大;管线自深海向近岸延展时,随水深的减小,冲刷深度分为缓慢发展阶段和快速发展阶段。 相似文献
13.
Submarine pipelines that transport crude oil and natural gas are often in a complex marine geological environment and may become unstable and fail upon impact by submarine landslides. Previous research has mostly focused on the impact forces exerted by submarine landslides on suspended pipelines, but the impact of submarine landslides on pipelines laid on the seafloor at various impact angles, θ, have been relatively infrequently discussed, and the effects of suspended height, H, on the impact forces exerted by submarine landslides on pipelines have not been thoroughly investigated. In this study, based on the Herschel–Bulkley model, the impact forces exerted by a submarine landslide on laid-on or suspended pipelines at various impact angles θ were simulated using the computational fluid dynamics (CFD) approach. Equations for calculating the axial and normal drag coefficients of a submarine pipeline were proposed. The CFD numerical simulation results were rearranged based on the soil mechanics approach. By comparing the parameters, an essentially corresponding relationship was found between the soil mechanics and CFD approaches when the equations were used to calculate the impact forces exerted by a submarine landslide on a pipeline. In addition, a semi-analytical expression for the failure envelope was provided. Furthermore, the effects of H on the forces on a pipeline were discussed, and an equation for calculating the acting forces on a pipeline along the flow direction of a submarine landslide that comprehensively accounts for the effects of θ and H was proposed. The lift force was discussed preliminarily and the results provide a basis for further investigation. The achievement of this study is applicable for selecting locations of submarine pipeline routes and for designing submarine pipelines. 相似文献
14.
Breakwaters with a berm can significantly reduce overtopping and reduce the required rock size compared to straight slopes without a berm. Here, the stability of rock slopes with a horizontal berm has been studied by means of physical model tests to provide information on the required rock size. The tests and analysis are focussed on the slope above the berm as well as the slope below the berm. Also the stability of the rock at the berm is addressed. The influence of the slope angle (1:2 and 1:4), the width of the berm, the level of the berm, and the wave steepness has been investigated. Based on the test results prediction formulae have been derived to quantify the required rock size for rubble mound breakwaters with a berm. Especially for the slope above the berm, the rock size can be reduced significantly compared to straight slopes. 相似文献
15.
16.
为解决不埋深海管道在温压荷载循环作用下，轴向移动量不断累积的问题，采用数值模拟方法，在论证了钢悬链线立管（steel catenary riser，SCR）张力相比于其他因素对管道轴向移动影响更为显著的基础上，针对一端受到SCR张力作用的短管，分析了不同轴向移动消减方案的作用特点。研究表明，对管道进行锚固能有效约束其轴向移动，且在中部锚固需要的锚固力及管道内产生的有效轴向力均较小；滑动基础可通过释放一定的管道位移量来减少管中的应力累积。因此将中部锚固与端部滑动相结合可优化锚固系统，使锚固力进一步下降54%，管中最大有效轴向压力减小33%，从而最有效地消减轴向移动。 相似文献
17.
Study on Interaction Relationship for Submarine Pipeline with Axial Corrosion Defects 总被引：2，自引：0，他引：2
Corrosion is one of the main reasons to cause the operation accident of submarine oil and gas transmission pipelines. As the major corrosion pattern in submarine pipelines, the effects of corrosion clusters consisting of the adjacent corrosion defects on failure pressure are investigated through non-linear large-deformation finite element method. Typically, the failure behavior and limit strength of submarine pipeline with axial groove-groove corrosion defect pair exposed to internal pressure are analyzed. The effects of corrosion depth and axial spacing between a pair of corrosion defects on failure pressure are concluded. An interaction relationship for corrosion defects in pipelines, as well as prediction formulations for assessing the remaining strength of corroded pipelines are proposed. The expressions based on the proposed interaction relationship give more accurate results than the methods used in the existing design guidelines. 相似文献