共查询到20条相似文献，搜索用时 171 毫秒
1.
A finite element model is constructed for a sliding friction bearing in a seismically isolated bridge under vertical excitation with contact/friction elements. The effects of vertical excitation on the seismic performance of a seismically isolated bridge with sliding friction bearings and different bearing friction coefficients and different stiffness levels (pier diameter) are discussed using example calculations, and the effects of excitation direction for vertical excitation on the analysis results are explored. The analysis results shows that vertical excitation has a relatively large impact on seismic performance for a seismically isolated bridge with sliding friction bearings, which should be considered when designing a seismically isolated bridge with sliding friction bearings where vertical excitation dominates. 相似文献
2.
Laminated elastomeric bearings have been widely used for small-to-medium-span highway bridges in China, in which concrete shear keys are set transversely to prohibit large girder displacement. To evaluate bridge seismic responses more accurately, proper analytical models of bearings and shear keys should be developed. Based on a series of cyclic loading experiments and analyses, rational analytical models of laminated elastomeric bearings and shear keys, which can consider mechanical degradation, were developed. The effect of the mechanical degradation was investigated by examining the seismic response of a small-to-medium-span bridge in the transverse direction under a wide range of peak ground accelerations (PGA). The damage mechanism for small-to-medium-span highway bridges was determined, which can explain the seismic damage investigation during earthquakes in recent years. The experimental results show that the mechanical properties of laminated elastomeric bearings will degrade due to friction sliding, but the degree of decrease is dependent upon the influencing parameters. It can be concluded that the mechanical degradation of laminated elastomeric bearings and shear keys play an important role in the seismic response of bridges. The degradation of mechanical properties of laminated elastomeric bearings and shear keys should be included to evaluate more precise bridge seismic performance. 相似文献
3.
为评估隔震和非隔震支座对桥梁地震易损性的影响,以一座3跨连续混凝土箱梁桥为分析对象,首先建立采用铅芯橡胶隔震支座与非隔震型盆式橡胶支座下桥梁的数值模型,求得不同程度地震作用下墩顶与支座的最大位移响应;再定义转角延性比损伤指标,结合支座剪应变,分析桥墩和支座的地震易损性情况;最后通过宽界限法建立全桥地震易损性曲线。研究结果表明,支座是较容易发生损坏的构件,而桥梁系统比桥墩或支座更易发生破坏,同时铅芯橡胶支座的破坏概率明显低于非隔震型盆式支座,可见采用隔震支座能有效减小桥墩墩顶在地震作用下的最大位移,此时桥墩地震易损性优于采用非隔震支座的情况。 相似文献
4.
Giuseppe Abbiati Oreste S. Bursi Philippe Caperan Luigi Di Sarno Francisco Javier Molina Fabrizio Paolacci Pierre Pegon 《地震工程与结构动力学》2015,44(13):2221-2240
This paper deals with the seismic response assessment of an old reinforced concrete viaduct and the effectiveness of friction‐based retrofitting systems. Emphasis was laid on an old bridge, not properly designed to resist seismic action, consisting of 12 portal piers that support a 13‐span bay deck for each independent roadway. On the basis of an OpenSEES finite element frame pier model, calibrated in a previous experimental campaign with cyclic displacement on three 1:4 scale frame piers, a more complex experimental activity using hybrid simulation has been devised. The aim of the simulation was twofold: (i) to increase knowledge of non‐linear behavior of reinforced concrete frame piers with plain steel rebars and detailing dating from the late 1950s; and (ii) to study the effectiveness of sliding bearings for seismic response mitigation. Hence, to explore the performance of the as built bridge layout and also of the viaduct retrofitted with friction‐based devices, at both serviceability and ultimate limit state conditions, hybrid simulation tests were carried out. In particular, two frame piers were experimentally controlled with eight‐actuator channels in the as built case while two frame piers and eight sliding bearings were controlled with 18‐actuator channels in the isolated case. The remaining frame piers were part of numerical substructures and were updated offline to accurately track damage evolution. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
5.
The convex model approach is applied to derive the robust seismic fragility curves of a five-span isolated continuous girder bridge with lead rubber bearings (LRB) in China. The uncertainty of structure parameters (the yield force and the post-yield stiffness of LRB, the yield strength of steel bars, etc.) are considered in the convex model, and the uncertainty of earthquake ground motions is also taken into account by selecting 40 earthquake excitations of peak ground acceleration magnitudes ranging from 0.125 to 1.126 g. A 3-D finite element model is employed using the software package OpenSees by considering the nonlinearity in the bridge piers and the isolation bearings. Section ductility of piers and shearing strain isolation bearings are treated as damage indices. The cloud method and convex model approach are used to construct the seismic fragility curves of the bridge components (LRB and bridge piers) and the bridge system, respectively. The numerical results indicate that seismic fragility of the bridge system and bridge components will be underestimated without considering the uncertainty of structural parameters. Therefore, the failure probability P f,max had better be served as the seismic fragility, especially, the fragility of the bridge system is largely dictated by the fragility of LRB. Finally, the probabilistic seismic performance evaluation of the bridge is carried out according to the structural seismic risk estimate method. 相似文献
6.
为完善大跨长联连续梁桥的减震和隔震技术,提出将负刚度装置引入某带有摩擦摆支座隔震的大跨长联连续梁桥中组成新型减震和隔震系统。基于CSIBridge软件建立全桥有限元模型,负刚度装置采用弹性多段线模拟,摩擦摆支座采用双线性恢复力模型,输入7条地震波进行了非线性时程分析,考查了新型减震和隔震系统下桥梁结构的地震反应,探究了负刚度系统对大跨长联隔震连续梁桥地震反应的影响。研究结果表明：在大跨长联隔震连续梁桥上布置负刚度装置后,梁体加速度及支座位移可被有效降低,近场地震动下的墩底内力也有明显减小。负刚度装置可有效提高大跨长联摩擦摆支座连续梁桥的抗震性能,负刚度装置也适用于大跨长联隔震连续梁桥。 相似文献
7.
For the purpose of accurately predicting the seismic response of base-isolated structures, an analytical hysteresis model for elastomeric seismic isolation bearings is proposed. An extensive series of experimental tests of four types of seismic isolation bearings—two types of high-damping rubber bearings, one type of lead-rubber bearing and one type of silicon rubber bearing—was carried out with the objective of fully identifying their mechanical characteristics. The proposed model is capable of well-predicting the mechanical properties of each type of elastomeric bearing into the large strain range. Earthquake simulator tests were also conducted after the loading tests of the individual bearings. In order to show the validity of the proposed model, non-linear dynamic analyses were conducted to simulate the earthquake simulator test results. Good agreement between the experimental and analytical results shows that the model can be an effective numerical tool to predict not only the peak response value but also the force–displacement relationship of the isolators and floor response spectra for isolated structures. © 1997 by John Wiley & Sons, Ltd. 相似文献
8.
为进一步评估隔震曲线梁桥在地震激励下的抗震性能,从地震易损性角度出发并兼顾考虑地震激励方向对其易损性的影响。利用APDL建立采用板式橡胶支座的隔震曲线梁桥有限元模型,从PEER中选取同一地震事件中的近断层地震动,按规范规定比例输入水平双向地震动进行非线性动力时程分析,结合地震响应与损伤指标计算得到各构件地震易损性曲线;考虑地震激励方向的变化,通过MATLAB编程绘制得到桥梁结构构件(桥墩与支座)以及整体系统的地震易损性曲面,分析探讨地震激励方向对隔震曲线梁桥易损性的影响。结果表明：不同极限状态下各桥墩切向损伤条件概率明显大于其径向,各支座的切向与径向易损性相差不大,但仍是各支座的切向易损性略大于径向易损性;桥梁各构件(桥墩与支座)切向易损性对地震激励方向均表现出很强依赖性,而径向易损性对其的依赖性相对较弱,且伴随损伤等级的提高,构件易损性对地震激励方向更加敏感;桥梁整体系统易损性对地震激励方向的变化不太敏感,且因各构件响应之间的相关性较高,其系统易损性更接近于易损性最大的构件——易损性下限;当进行隔震曲线梁桥抗震性能评估时,应考虑不同地震激励方向对其地震易损性的影响,从而使得易损性分析... 相似文献
9.
E. Tubaldi S. A. Mitoulis H. Ahmadi A. Muhr 《Bulletin of Earthquake Engineering》2016,14(4):1285-1310
This paper investigates the potential tensile loads and buckling effects on rubber-steel laminated bearings on bridges. These isolation bearings are typically used to support the deck on the piers and the abutments and reduce the effects of seismic loads and thermal effects on bridges. When positive means of fixing of the bearings to the deck and substructures are provided using bolts, the isolators are exposed to the possibility of tensile loads that may not meet the code limits. The uplift potential is increased when the bearings are placed eccentrically with respect to the pier axis such as in multi-span simply supported bridge decks. This particular isolator configuration may also result in excessive compressive loads, leading to bearing buckling or in the attainment of other unfavourable limit states for the bearings. In this paper, an extended computer-aided study is conducted on typical isolated bridge systems with multi-span simply-supported deck spans, showing that elastomeric bearings might undergo tensile stresses or exhibit buckling effects under certain design situations. It is shown that these unfavourable conditions can be avoided with the rational design of the bearing properties and in particular of the shape factor, which is the geometrical parameter controlling the axial bearing stiffness and capacity for a given shear stiffness. Alternatively, the unfavourable conditions could be reduced by reducing the flexural stiffness of the continuity slab. 相似文献
10.
11.
为了提高采用板式橡胶支座的斜梁桥横向抗震能力,揭示其在不同设计参数下的横向抗震行为,考虑板式橡胶支座的滑移、钢筋混凝土挡块的滞回力学性能、桥台-背土效应等非线性因素,采用OpenSEES建立某连续斜梁桥的三维分析模型,提出支座位移评价指标、主梁平面转角指标、墩柱曲率延性指标和抗剪指标,研究不同挡块强度和间隙组合下桥梁的横向抗震性能。研究表明:同时增大挡块强度和间隙,总体上会降低支座的横向变形,但会增加其纵向变形;挡块强度越高,主梁的横向位移有所下降,但平面转角越大,对两侧桥台处的支座抗剪越不利;挡块强度越高,间隙越小,墩柱越有可能进入弹塑性状态。在本文桥例中,当挡块强度取40%支反力,间隙取0.08m时,所有抗震指标都可满足规范要求。 相似文献
12.
Different levels of model sophistication have recently emerged to support seismic risk assessment of bridges, but mostly at the expense of neglecting the influence of vertical ground motions (VGMs). In this paper, the influence of VGMs on bridge seismic response is presented and the results are compared with the case of horizontal‐only excitations. An advanced finite element model that accounts for VGMs is first developed. Then, to investigate the effect of soil–structure interaction (SSI) including liquefaction potential, the same bridge with soil‐foundation and fixed boundary conditions is also analyzed. Results show that the inclusion of the VGMs has a significant influence on the seismic response, especially for the axial force in columns, normal force of bearings, and the vertical deck bending moments. However, VGMs do not have as much influence on the seismic demand of the pile cap displacements or pile maximum axial forces. Also, the significant fluctuation of the column axial force can reduce its shear and flexural capacity, and a heightened reversal of flexural effects may induce damage in the deck. In addition, relative to the fixed base case, SSI effects tend to reduce response quantities for certain ground motions while increasing demands for others. This phenomenon is explained as a function of the frequency content of the ground motions, the shift in natural vertical periods, and the VGM spectral accelerations at higher modes. Moreover, the mechanisms of liquefaction are isolated relative to SSI effects in nonliquefiable soils, revealing the influence of liquefaction on bridge response under VGMs. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
13.
不同约束方式对匝道桥动力特性的影响研究 总被引：1，自引：0，他引：1
近年来,地震作用下的匝道桥表现出较高的地震易损性。为建立匝道桥的有效约束方式,以减小其地震损伤,本文基于汶川地震中连续梁桥约束方式的调研结果,建立了4种不同匝道桥支座约束方式,并以石家庄石环线某匝道桥为例,对比分析了不同约束方式下匝道桥的自振特性及地震响应。结果表明:板式橡胶支座具有一定的剪切变形能力,可降低桥墩与支座组成的体系刚度,有效分散了上部结构的地震惯性力,保护了下部结构,但应注意其引起的较大主梁位移;固定支座或墩梁固结形式会放大桥墩受力,增加下部结构的损坏,不宜设置在高度较矮、刚度较大的桥墩上;双层挡块和垫石凹槽分级限位支座具有较好的限位能力,并可耗散部分地震能量。 相似文献
14.
从板式橡胶支座及混凝土挡块抗震设计角度,以一座典型的3跨预应力混凝土连续梁桥为例,结合概率地震需求分析及桥墩、支座等抗震关键构件极限破坏状态,建立不同支座及挡块分析模型的中小跨径梁桥地震易损性曲线,研究考虑支座滑移效应及挡块破坏的中小跨径梁桥的易损性特征。研究结果表明:不考虑橡胶支座的滑移效应及混凝土挡块破坏,桥墩地震破坏概率明显增大,且会低估支座破坏概率;桥梁系统易损性受支座破坏状态的影响显著,需设置合理的限位装置;在中小跨径梁桥地震易损性分析中,考虑支座的滑移效应及混凝土挡块的破坏十分必要。 相似文献
15.
结合长联大跨连续梁桥的特点,以1座(65+123+156+123+10×90+55)m长联大跨摩擦摆支座隔震连续梁桥为背景,建立了全桥三维有限元模型,运用非线性时程分析法,分析了地震动输入模式、地震动强度、摩擦摆支座参数对该桥内力、位移和能量响应的影响。研究结果表明:(1)长联大跨连续梁桥布置摩擦摆支座,可有效延滞固定墩顶有效主梁质量效应,实现全桥协同抗震。大部分地震能量可通过支座滞回耗能散耗,大幅降低了该桥固定墩地震能量耗散需求。(2)长联大跨连续梁桥减隔震设计中,建议采用水平单向+竖向地震组合进行内力设计,采用三向地震组合进行位移设计。(3)强震作用下,支座摩擦因数取0.029~0.034时该桥隔震性能最优。 相似文献
16.
17.
以一座典型山区非规则梁桥为研究对象,建立了该桥梁多维多点激励下的多自由度动力计算模型,研究了该桥梁在多维多点激励下考虑支座摩擦滑移及结构碰撞等非线性因素时的抗震性能。研究结果表明:相比一维地震输入,多维地震可使结构的动力响应增加,桥墩底部弯矩需求增大;相比一致激励,多点激励可使得支座的位移需求增大,且地震波最后到达的桥墩上方支座位移最大;同时考虑多点激励和碰撞效应可使桥墩的弯矩需求增加;水平地震作用下,矮墩上部的支座容易滑动,且双向地震较单向地震更明显,三向地震输入较双向有所增强。因此,对山区非规则梁桥进行抗震设计时应有针对性地进行多维多点地震输入计算,找出结构的最大地震需求,以期指导设计。 相似文献
18.
Damage investigation of small to medium-span highway bridges in Wenchuan earthquake revealed that typical damage of these bridges included: sliding between laminated-rubber bearings and bridge girders, concrete shear keys failure, excessive girder displacements and even span collapse. However, the bearing sliding could actually act as a seismic isolation for piers, and hence, damage to piers for these bridges was minor during the earthquake. Based on this concept, an innovative solation system for highway bridges with laminated-rubber bearings is developed. The system is comprised of typical laminated-rubber bearings and steel dampers. Bearing sliding is allowed during an earthquake to limit the seismic forces transmitting to piers, and steel dampers are applied to restrict the bearing displacements through hysteretic energy dissipation. As a major part of this research, a quarter-scale, two-span bridge model was constructed and tested on the shake tables to evaluate the performance of this isolation system. The bridge model was subjected to a Northridge and an artificial ground motion in transverse direction. Moreover, numerical analyses were conducted to investigate the seismic performance of the bridge model. Besides the test bridge model, a benchmark model with the superstructure fixed to the substructure in transverse direction was also included in the numerical analyses. Both the experimental and the numerical results showed high effectiveness of this proposed isolation system in the bridge model. The system was found to effectively control the pier-girder relative displacements, and simultaneously, protect the piers from severe damage. Numerical analyses also validated that the existing finite element methods are adequate to estimate the seismic response of bridges with this isolation system. 相似文献
19.
The widespread use of sliding bearings for the seismic isolation of structures
requires detailed knowledge of their behavior and improved modeling capability under seismic conditions. The paper summarizes the results of a large experimental investigation on steel–PTFE interfaces, aimed at evaluating the effects of sliding velocity, contact pressure, air temperature and state of lubrication on the mechanical behavior of steel-PTFE sliding bearings. Based on the experimental outcomes, two different mathematical models have been calibrated, which are capable of accounting for the investigated parameters in the evaluation of the sliding friction coefficient. The first model is basically an extension of the model proposed by Constantinou et al. (1990)Journal of Earthquake Engineering, 116(2), 455–472, while the second model is derived from the one proposed by Changet al. (1990)Journal of Engineering Mechanics, 116, 2749–2763. Expressions of the model parameters as a function of bearing pressure and air temperature are presented for lubricated and non-lubricated sliding surfaces. Predicted and experimental results are finally compared. 相似文献
20.
活动支座摩擦力对简支梁桥地震反应的影响 总被引：3，自引：0，他引：3
本文介绍在地震作用下活动支座摩擦力简支梁桥桥墩内力和活动支座外墩,梁相对位 影响,以及水平地震系数,摩擦系数变化对固定支座水平地震荷载的影响。文中建议了考察活动以座摩擦力的简支梁桥整体分析模型。 相似文献