共查询到20条相似文献，搜索用时 31 毫秒
1.
Tide-driven bed load transport is an important portion of the net annual sediment transport rate in many shoreface and shelf environments. However, bed load transport under waves cannot be measured in the field and bed load transport by currents without waves is barely measurable, even in spring tidal conditions. There is, consequently, a strong lack of field data and validated models. The present field site was on the shoreface and inner shelf at 2 to 8.5 km offshore the central Dutch coast (far outside the surfzone), where tidal currents flow parallel to the coast. Bed load transports were carefully measured with a calibrated sampler in spring tidal conditions without waves at a water depth of 13–18 m with fine and medium sands. The near-bed flow was measured over nearly a year and used for integration to annual transport rates. An empirical bed load model was derived, which predicts bed load transports that are a factor of > 5 smaller than predicted by existing models. However, they agree with laboratory data of sand and gravel transport in currents near incipient motion. The damped transport rates may have been caused by cohesion of sediment or turbulence damping due to mud or biological activity. The annual bed load transport rate was calculated using a probability density function (pdf) derived from the near-bed current and orbital velocity data which represented the current and wave climate well when compared to 30 years of data from a nearby wave station. The effect of wave stirring was included in the transport calculations. The net bed load transport rate is a few m2/year. This is much less than predicted in an earlier model study, which is partly due to different bed load models but also due to the difference in velocity pdf. The annual transport rate is very sensitive to the probability of the largest current velocities. 相似文献
2.
This work concerns the wave plus current flow over a sand bed covered by vortex ripples, with the current and the waves coming from different angles. Experiments were performed in a basin, where current and waves were perpendicular, in order to determine the conditions (current strength) leading to a regular ripple pattern formation. Numerical simulations were conducted changing the direction between the waves and the current from 0° to 90° and the ratio between the current strength and the wave orbital velocity from 0.2 to 1.5. Close to the bed, the current aligns parallel to the ripple crests, leading to a veering current profile with the vertical coordinate. The current-related friction coefficient was calculated. It was found that it decreases as the angle approaches 90°, while it increases for decreasing values of the current with a trend that can be described by a power law. 相似文献
3.
Jebbe J. van der Werf Jolanthe J.L.M. Schretlen Jan S. Ribberink Tom O'Donoghue 《Coastal Engineering》2009
A new database of laboratory experiments involving sand transport processes over horizontal, mobile sand beds under full-scale non-breaking wave and non-breaking wave-plus-current conditions is described. The database contains details of the flow and bed conditions, information on which quantities were measured and the value of the measured net sand transport rate for 298 experiments conducted in 7 large-scale laboratory facilities. Analysis of the coverage of the experiments and the measured net sand transport rates identified the following gaps in the range of test conditions and/or the type of measurements: (i) graded sand experiments, (ii) wave-plus-current experiments and (iii) intra-wave velocity and concentration measurements in the ripple regime. Furthermore, it highlights two areas requiring further research: (i) the differences in sand transport processes and sand transport rates between real waves and tunnel flows with nominally similar near-bed oscillatory flow conditions and (ii) the effects of acceleration skewness on transport rates. The database is a useful resource for the development and validation of sand transport models for coastal applications. 相似文献
4.
Variability of wave-induced ripple migration in wave-flume experiments and its implications for sediment transport 总被引：1，自引：0，他引：1
A thorough discussion of results from laboratory experiments with regular waves sheds light on the gap that lies between the sediment transport associated with ripple migration and the performance of a standard bedload transport formula in terms of bed shear concept. It is found that the extent of deviations of the bedload transport formula by Ribberink (1998) from the measured rate of sediment transport associated with ripple migration becomes systematically apparent under conditions of increasing settling time factor Ωs (= η/(w0T); η is the ripple height, w0 the settling velocity and T the wave period). Re-examination of previous two field studies demonstrates a further reinforcement for phase-lag argument addressed in this paper. 相似文献
5.
Predictability of wave-induced net sediment transport using the conventional 1DV RANS diffusion model 总被引：1，自引：0，他引：1
Based on a large database of laboratory experiments, the predictability of the conventional one-dimensional vertical Reynolds-averaged Navier–Stokes (RANS) diffusion model is systematically investigated with respect to wave-induced net sediment transport. The predicted net sediment transport rates are compared with the measured data of 176 physical experiments in wave flumes and oscillating water tunnels, covering a wide range of wave conditions (surface, skewed, and asymmetric waves with and without currents), sediment conditions (fine, medium, and coarse sands with median grain diameters ranging from 0.13 to 0.97 mm) and bed forms (flat beds and rippled beds), corresponding to various sediment dynamic regions in the near-shore area. Comparisons show that the majority (73 %) of predictions on a flat bed are within a factor 2 of the measurements. The model behaves much better for medium/coarse sand than for fine sand. The model generally underpredicts the transport rates beneath asymmetric waves and overpredicts the fine sand transport beneath skewed waves. Nevertheless, the model behaves well in reproducing the transport rates under surface waves. A detailed discussion and a quantitative measure of the overall model performance are made. The poor model predictability for fine sand cases is mainly due to the underestimation of unsteady phase-lag effect. It is revealed that the model predictability can be significantly improved by implementing alternative bedload formulas and incorporating more physical processes (mobile-bed roughness, hindered settling, and turbulence damping). 相似文献
6.
《Coastal Engineering》2006,53(8):657-673
A new series of laboratory experiments was performed in the Aberdeen Oscillatory Flow Tunnel (AOFT) and the Large Oscillating Water Tunnel (LOWT) to investigate time-averaged suspended sand concentrations and transport rates over rippled beds in regular and irregular oscillatory flow. The wave-induced oscillatory near-bed flows were simulated at full-scale. Five series of experiments were carried out. During the two AOFT experimental series, ripple dimensions, ripple migration rates and net sand transport rates were measured under regular and irregular asymmetric flow for two different sand types. The three LOWT experimental series focussed on measurements of the ripple dimensions, ripple migration rates, time-averaged suspended sand concentrations and net sand transport rates under regular asymmetric and irregular weakly asymmetric flow for two different sand types. From analysis of new and other full-scale data, it is concluded that the lower part of the time- and bed-averaged concentration profile (up to two times the ripple height above the ripple crest level) has an exponential profile. A new reference concentration formula is proposed based on the formula of Bosman and Steetzel [Bosman, J.J., Steetzel, H.J., 1986. Time- and bed-averaged concentration under waves. Proc. 20th ICCE Taipei, ASCE, pp. 986–1000], which includes the grain-size influence. Furthermore, it is shown that the concentration decay length is strongly related to the ripple height and that the simple formula Rc = 1.27η gives good agreement with the data. A new transport model is proposed for the wave-related net transport over full-scale ripples based on a modified half wave cycle concept of Dibajnia and Watanabe [Dibajnia, M., Watanabe, A., 1992. Sheet flow under nonlinear waves and currents. Proc. 23rd ICCE Venice, ASCE, pp. 2015–2028; Dibajnia, M., Watanabe, A., 1996. A transport rate formula for mixed sands. Proc. 25th ICCE Orlando, ASCE, pp. 3791–3804]. The magnitudes of the half wave cycle transport contributions are related to the grain-related Shields parameter, the degree of wave asymmetry and a newly defined vortex suspension parameter P, which is the ratio between the ripple height and the median grain-size. The new model has been calibrated using transport data from the new regular flow experiments and has subsequently been validated using other data, including measurements from irregular flow experiments. The new model is seen to perform better overall than existing practical models for ripple regime net sand transport. 相似文献
7.
8.
Many existing practical sand transport formulae for the coastal marine environment are restricted to a limited range of hydrodynamic and sand conditions. This paper presents a new practical formula for net sand transport induced by non-breaking waves and currents. The formula is especially developed for cross-shore sand transport under wave-dominated conditions and is based on the semi-unsteady, half wave-cycle concept, with bed shear stress as the main forcing parameter. Unsteady phase-lag effects between velocities and concentrations, which are especially important for rippled bed and fine sand sheet-flow conditions, are accounted for through parameterisations. Recently-recognised effects on the net transport rate related to flow acceleration skewness and progressive surface waves are also included. To account for the latter, the formula includes the effects of boundary layer streaming and advection effects which occur under real waves, but not in oscillatory tunnel flows. The formula is developed using a database of 226 net transport rate measurements from large-scale oscillatory flow tunnels and a large wave flume, covering a wide range of full-scale flow conditions and uniform and graded sands with median diameter ranging from 0.13 mm to 0.54 mm. Good overall agreement is obtained between observed and predicted net transport rates with 78% of the predictions falling within a factor 2 of the measurements. For several distinctly different conditions, the behaviour of the net transport with increasing flow strength agrees well with observations, indicating that the most important transport processes in both the rippled bed and sheet flow regime are well captured by the formula. However, for some flow conditions good quantitative agreement could only be obtained by introducing separate calibration parameters. The new formula has been validated against independent net transport rate data for oscillatory flow conditions and steady flow conditions. 相似文献
9.
An artificial sand wave on the Dutch shoreface of the North Sea has been studied in conditions with relatively strong tidal currents in the range of 0.5 to 1 m/s and sediments in the medium sand size range of 0.2 to 0.5 mm. The sand wave is perpendicular to the tidal current and has a maximum height and length of the order of 5 m and 1 km, respectively. The sand wave is dynamically active and shows migration rates of the order of a few metres per year. A numerical morphodynamic model (DELFT3D model) has been used to simulate the morphological behaviour of the sand wave in the North Sea. This model approach is based on the numerical solution of the three-dimensional shallow water equations in combination with a surface wave propagation model (wind waves) and the advection–diffusion equation for the sediment particles with online bed updating after each time step. The model results show that the sand wave grows in the case of dominant bed-load transport (weak tidal currents; relatively coarse sediment; small roughness height; low waves) and that the sand wave decays in the case of dominant suspended transport (strong currents, relatively fine sediment, large roughness height; storm waves). 相似文献
10.
1 IntroductionIn coastal areas a ubiquitous phenomenon is theformation of ripples in the seabed. It is now widelyaccepted that the flow and sediment transport overseabed are vital in relation to erosion, surface wavedissipation and pollution dispersion et… 相似文献
11.
《Coastal Engineering》2006,53(11):897-913
For the general purposes of morphodynamic computations in coastal zones, simple formula-based models are usually employed to evaluate sediment transport. Sediment transport rates are computed as a function of the bottom shear stress or the near bed flow velocity and it is generally assumed that the sediment particles react immediately to changes in flow conditions. It has been recognized, through recent laboratory experiments in both rippled and plane bed sheet flow conditions that sediment reacts to the flow in a complex manner, involving non-steady processes resulting from memory and settling/entrainment delay effects. These processes may be important in the cross-shore direction, where sediment transport is mainly caused by the oscillatory motions induced by surface short gravity waves.The aim of the present work is to develop a semi-unsteady, practical model, to predict the total (bed load and suspended load) sediment transport rates in wave or combined wave-current flow conditions that are characteristic of the coastal zone. The unsteady effects are reproduced indirectly by taking into account the delayed settling of sediment particles. The net sediment transport rates are computed from the total bottom shear stress and the model takes into account the velocity and acceleration asymmetries of the waves as they propagate towards the shore.A comparison has been carried out between the computed net sediment transport rates with a large data set of experimental results for different flow conditions (wave-current flows, purely oscillatory flow, skewed waves and steady currents) in different regimes (plane bed and rippled bed) with fine, medium and coarse uniform sand. The numerical results obtained are reasonably accurate within a factor of 2. Based on this analysis, the limits and validity of the present formulation are discussed. 相似文献
12.
《Coastal Engineering》1999,36(3):171-195
A morphological stability analysis is carried out for a long straight coast with a longshore bar. The situation with oblique wave incidence and a wave-driven longshore current is considered. The flow and sediment transport are described by a numerical modelling system. The models comprise: (i) a wave model with depth refraction, shoaling and wave breaking, (ii) a depth integrated model for wave driven currents and (iii) a sediment transport model for the bed load transport and the suspended load transport in combined waves and current. The direction of the sediment transport is taken to be parallel to the depth integrated mean current velocity, neglecting the effects of a bed slope and secondary currents. An instability is found to develop around the bar crest. The instability is periodic in the alongshore direction, and tends to form rip channels and to steepen the offshore face of the bar between the rip channels. The alongshore wave length of the most unstable perturbation is determined for different combinations of the wave conditions and the geometry of the profile. 相似文献
13.
I~crIOWIn the coastal area, especially at the sandy seashore, wave and nearshore current are the major factors which affect sediment transPOrt and the motyhChdynamics.The numerical models of predicting the beach evolution can be classified intO the medi~term and long-term models according to their space and time scales (De Briend et al., 1993;Watanabe, 1990; Watanabe et al., 1986; Tao, 1996). In the medium-term model the effects ofwave, nearshore current and sediment transport are conside… 相似文献
14.
The present paper proposes a numerical model to determine horizontal and vertical components of the hydrodynamic forces on a slender submarine pipeline lying at the sea bed and exposed to non-linear waves plus a current. The new model is an extension of the Wake II type model, originally proposed for sinusoidal waves (Soedigdo et al., 1999) and for combined sinusoidal waves and currents (Sabag et al., 2000), to the case of periodic or random waves, even with a superimposed current. The Wake II type model takes into account the wake effects on the kinematic field and the time variation of drag and lift hydrodynamic coefficients. The proposed extension is based on an evolutional analysis carried out for each half period of the free stream horizontal velocity at the pipeline. An analytical expression of the wake velocity is developed starting from the Navier–Stokes and the boundary layer equations. The time variation of the drag and lift hydrodynamic coefficients is obtained using a Gaussian integration of the start-up function. A reduced scale laboratory investigation in a large wave flume has been conducted in order to calibrate the empirical parameters involved in the proposed model. Different wave and current conditions have been considered and measurements of free stream horizontal velocities and dynamic pressures on a bottom-mounted pipeline have been conducted. The comparison between experimental and numerical hydrodynamic forces shows the accuracy of the new model in evaluating the time variation of peaks and phase shifts of the horizontal and vertical wave and current induced forces. 相似文献
15.
This paper provides an approach by which the scour depth below pipelines in shoaling conditions beneath non-breaking and breaking random waves can be derived. Here the scour depth formula in shoaling conditions for regular non-breaking and breaking waves with normal incidence to the pipeline presented by Cevik and Yüksel [Cevik, E. and Yüksel, Y., (1999). Scour under submarine pipelines in waves in shoaling conditions. ASCE J. Waterw., Port, Coast. Ocean Eng., 125 (1), 9–19.] combined with the wave height distribution including shoaling and breaking waves presented by Mendez et al. [Mendez, F.J., Losada, I.J. and Medina, R., (2004). Transformation model of wave height distribution on planar beaches. Coast. Eng. 50 (3), 97–115.] are used. Moreover, the approach is based on describing the wave motion as a stationary Gaussian narrow-band random process. An example of calculation is also presented. 相似文献
16.
The newly developed nearshore circulation model, SHORECIRC, using a hybrid finite-difference finite-volume TVD-type scheme, is coupled with the wave model SWAN in the Nearshore Community Model (NearCoM) system. The new modeling system is named NearCoM-TVD and the purpose of this study is to report the capability and limitation of NearCoM-TVD for several coastal applications. For tidal inlet applications, the model is verified with the semi-analytical solution of Keulegan (1967) for an idealized inlet-bay system. To further evaluate the model performance in predicting nearshore circulation under intense wave–current interaction over complex bathymetry, modeled circulation patterns are validated with measured data during RCEX field experiment (MacMahan et al., 2010). For sediment transport applications, two sediment transport models are applied to predict three sandbar migration events at Duck, NC, during August to October 1994 (Gallagher et al., 1998). The model of Kobayashi et al. (2008) incorporates wave-induced onshore sediment transport rate as a function of the standard deviation of wave-induced horizontal velocities. The modeled beach profile evolution for two offshore events and one onshore event agrees well with the measured data. The second model investigated here combines two published sediment transport models, namely, the total load model driven by currents under the effect of wave stirring (Soulsby, 1997) and the wave-driven sediment transport model due to wave asymmetry/skewness (van Rijn et al., 2011). The model study with limited field data suggests that the parameterization of wave stirring is appropriate during energetic wave conditions. However, during low energy wave conditions, the effect of wave stirring needs to be re-calibrated. 相似文献
17.
Shear stresses on a rough seabed under irregular waves plus current are calculated. Parameterized models valid for regular waves plus current have been used in Monte Carlo simulations, assuming the wave amplitudes to be Rayleigh-distributed. Numerical estimates of the probability distribution functions are presented. For waves only, the shear stress maxima follow a Weibull distribution, while for waves plus current, both the maximum and time-averaged shear stresses are well represented by a three-parameter Weibull distribution. The behaviour of the maximum shear stresses under a wide range of wave-current conditions has been investigated, and it appears that under certain conditions, the current has a significant influence on the maximum shear stresses. Results of comparison between predictions and measurements of the maximum bottom shear stresses from laboratory and field experiments are presented. 相似文献
18.
Following Bagnold's approach, a relationship between sediment transport and energy dissipation is developed. The major assumption made in the study is that the near bed velocity plays a dominant role in the process of sediment transport. A general relationship between energy dissipation and sediment transport is first proposed. Then the equations for total sediment transport are derived by introducing the appropriate expression of energy dissipation rate under different conditions, such as open channel flows, combination of wave and current, as well as longshore sediment transport. Within the flows investigated, the derived relationships are fairly consistent with the available data over a wide range of conditions. 相似文献
19.
Owing to lack of observational data and accurate definition,it is difficult to distinguish the Kuroshio intrusion water from the Pacific Ocean into the South China Sea(SCS).By using a passive tracer to identify the Kuroshio water based on an observation-validated three-dimensional numerical model MITgcm,the spatio-temporal variation of the Kuroshio intrusion water into the SCS has been investigated.Our result shows the Kuroshio intrusion is of distinct seasonal variation in both horizontal and vertical directions.In winter,the intruding Kuroshio water reaches the farthest,almost occupying the area from 18°N to 23°N and 114°E to 121°E,with a small branch flowing towards the Taiwan Strait.The intrusion region of the Kuroshio water decreases with depth gradually.However,in summer,the Kuroshio water is confined to the east of 118°E without any branch reaching the Taiwan Strait;meanwhile the intrusion region of the Kuroshio water increases from the surface to the depth about 205 m,then it decreases with depth.The estimated annual mean of Kuroshio Intrusion Transport(KIT) via the Luzon Strait is westward to the SCS in an amount of –3.86×106 m3/s,which is larger than the annual mean of Luzon Strait Transport(LST) of –3.15×106 m3/s.The KIT above 250 m accounts for 60%–80% of the LST throughout the entire water column.By analyzing interannual variation of the Kuroshio intrusion from the year 2003 to 2012,we find that the Kuroshio branch flowing into the Taiwan Strait is the weaker in winter of La Ni?a years than those in El Ni?o and normal years,which may be attributed to the wind stress curl off the southeast China then.Furthermore,the KIT correlates the Ni?o 3.4 index from 2003 to 2012 with a correlation coefficient of 0.41,which is lower than that of the LST with the Ni?o 3.4 index,i.e.,0.78. 相似文献
20.
Field measurements of cross-shore currents 0.25 m from the bed were made on two natural beaches under a range of incident wave conditions. The results indicated the presence of a relatively strong, offshore-directed mean current, both within and seaward of the surf zone. Typical velocities within the surf zone were of the order of 0.2–0.3 m/s. This bed return flow, or “undertow”, represents a mass conservation response, returning water seaward that was initially transported onshore in the upper water column, primarily above the trough of the incident waves. The measurements demonstrated that the bed return flow velocity increases with the incident wave height. In addition, the crossshore distribution of the bed return flow is characterised by a mid-surf zone maximum, which exhibits a strong decrease in velocity towards the shoreline and a more gradual decay in the offshore direction. Several bed return flow models based on mass continuity were formulated to predict the cross-shore distribution of the bed return flow under an irregular wave field and were compared with the field data. Best agreement was obtained using shallow water linear wave theory, after including the mass transport associated with unbroken waves. The contribution of the unbroken waves enables net offshore-directed bottom currents to persist outside the region of breaking waves, providing a mechanism, other than rip currents, to transport sediment offshore beyond the surf zone. 相似文献