首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
ABSTRACT

The uplift capacity of a group of circular plate anchors buried horizontally in sand along a line has been determined. The uplift capacity of an interfering anchor is presented in terms of nondimensional uplift factors, Fγi and Fqi, due to components of soil unit weight and surcharge pressure acting on the ground surface, respectively. Theoretical solutions have been developed by applying the upper bound theorem of limit analysis based on a simple rigid wedge collapse mechanism. In the case of two and infinite number of anchors, closed-form solutions have been developed for computing the factor Fqi, whereas the factor Fγi is determined using a semianalytical approach. As expected, the interference of the anchors leads to a continuous reduction in the uplift resistance with a decrease in the spacing between the anchors, and the uplift resistance decreases with the increasing number of anchors at a given spacing. The results compare reasonably well with the available theoretical and experimental data from the literature.  相似文献   

2.
Abstract

This study describes an analytical solution for determining the ultimate vertical uplift resistance of a group of two and multiple number of close-spaced shallow rectangular anchor plates embedded horizontally in sand. The analysis was performed by using an upper bound theorem of limit analysis with the employment of the kinematically admissible three-dimensional (3D) rigid wedge collapse mechanisms. Results are obtained in terms of dimensionless uplift factors Fγ and Fq due to the components of soil self-weight and surcharge pressure acting on the ground surface for a wide range of parameters. It was found that the magnitude of uplift factors decreases substantially with a decrease in the clear spacing between the anchors, soil friction angle, and embedment ratio, and an increase in the aspect ratio of anchors. Further, it was noticed that when the clear spacing between the anchors is greater than or equal to the certain critical value, the interaction effect of anchors vanishes and the magnitude of uplift factors associated with a group of anchors becomes equal to that of single isolated anchors. The present solutions are found to compare reasonably well with those theoretical, numerical, and experimental results available in the literature.  相似文献   

3.
ABSTRACT

The OMNI-Max anchors are newly developed dynamically installed anchors for deep water mooring systems. After installation, the anchor is keyed to a new orientation and position by tensing the attached mooring chain, which is known as the “keying process”. This study conducted 1g model tests to study the trajectories and capacity developments of OMNI-Max anchors in homogeneous and lightly overconsolidated (LOC) clays. A testing arrangement was designed to simulate the anchor keying process with a constant pullout angle at the mudline. A half model anchor which could move against the box glass was used to determine the anchor trajectory in the soil. The effects of padeye offset angle, uplift angle at the mudline, anchor fluke thickness, anchor initial embedment depth, and soil strength on the anchor trajectory and capacity were systematically investigated. Moreover, the critical uplift angle at the padeye and the anchor critical initial embedment depth were discussed. The results indicate that the anchor can dive both in homogeneous and LOC clays under certain conditions. A padeye offset angle of 24–30° is recommended for the OMNI-Max anchor to maintain high capacity and diving trend simultaneously. Besides, the anchor diving trend can be improved with small uplift angles at the mudline and with thick anchor flukes. A critical initial embedment depth of 1.3 times the anchor length is recommended to preclude the anchor from being pulled out.  相似文献   

4.
Uplift response of symmetrical anchor plates with and without grid fixed reinforced （GFR） reinforcement was evaluated in model tests and numerical simulations by Plaxis. Many variations of reinforcement layers were used to reinforce the sandy soil over symmetrical anchor plates. In the current research, different factors such as relative density of sand, embedment ratios, and various GFR parameters including size, number of layers, and the proximity of the layer to the symmetrical anchor plate were investigated in a scale model. The failure mechanism and the associated rupture surface were observed and evaluated. GFR, a tied up system made of fiber reinforcement polymer （FRP） strips and end balls, was connected to the geosynthetic material and anchored into the soil. Test results showed that using GFR reinforcement significantly improved the uplift capacity of anchor plates. It was found that the inclusion of one layer of GFR, which rested directly on the top of the anchor plate, was more effective in enhancing the anchor capacity itself than other methods. It was found that by including GFR the uplift response was improved by 29%. Multi layers of GFR proved more effective in enhancing the uplift capacity than a single GFR reinforcement. This is due to the additional anchorage provided by the GFR at each level of reinforcement. In general, the results show that the uplift capacity of symmetrical anchor plates in loose and dense sand can be significantly increased by the inclusion of GFR. It was also observed that the inclusion of GFR reduced the requirement for a large L/D ratio to achieve the required uplift capacity. The laboratory and numerical analysis results are found to be in agreement in terms of breakout factor and failure mechanism pattern.  相似文献   

5.
Drag anchor is a widely used economical anchor option for offshore floating structures. The anchor behavior under unidirectional loading and combined loading is important for anchor selection. The anchor behavior under combined loading, characterized by the yield envelope, can also be used for the prediction of anchor installation, which is still an issue in anchor design. However, most existing studies on anchor capacity are for plate anchors which focused only on the anchor pullout capacity in soil with uniform shear strength. The behavior of drag anchor under unidirectional and combined loading in soil with linearly increasing shear strength profile is seldom investigated. The current 2D finite element studies investigate the anchor behavior for a horizontal anchor fluke in clay with linearly increasing shear strength under unidirectional vertical, horizontal and rotational loadings first. Then based on the results of anchor unidirectional loading behavior, the yield envelopes for anchor under combined loading for both shallow and deep embedded flukes are studied. The effect of anchor embedment depth, soil non- homogeneity, soil overburden pressure and the soil/anchor interface breakaway conditions are studied to provide insight for drag anchor design.  相似文献   

6.
Laboratory model test results for the uplift of a shallow circular plate anchor embedded in a soft saturated clay are presented. For all tests the bottom of the anchor plate was vented to eliminate the mud suction force. The tests were divided into two categories: (1) short‐term tests to determine the variation of the net ultimate uplift capacity and hence the breakout factor with embedment ratio, and (2) creep tests with sustained uplift loads at varying embedment ratios. Based on the model test results, the variation with time, has been determined for the rate of strain of the soil located above the plate anchor. Empirical relationships for obtaining the rate of anchor uplift have been proposed.  相似文献   

7.
In the field of ocean engineering, a beginning has been made in the use of large‐sized suction anchors for safe anchoring of large compliant structures. Suction anchors derive most of their uplift resistance from passive suction developed during the pullout movement. This article describes a set of laboratory tests on model suction anchors of three different embedment ratios to estimate the pullout behavior of suction anchors in soft clays typical of Indian marine clays. Tests were conducted on model anchors installed in soil beds prepared at four different consistencies in a test tank. This study shows the influence of soil consistency and embedment ratio (L/D) on the pullout behavior of suction anchors and on the variation of suction pressure at the top of the soil plug. The test results reveal that the behavior of suction anchors is much better than the behavior of open‐ended anchors from the considerations of both capacity and deformation. The consistent development of suction inside the anchor top confirms the plug formation and significant breakout resistance in the form of suction‐induced reversed end bearing. The results are further analyzed in terms of suction breakout factors. Further, the effect of burial depth of suction anchor on pullout behavior is shown.  相似文献   

8.
In petroleum industry, the difference between pore pressure (Pp) and minimum horizontal stress Sh (termed the seal or retention capacity) is of major consideration because it is often assumed to represent how close a system is to hydraulic failure and thus the maximum hydrocarbon column height that can be maintained. While Sh and Pp are often considered to be independent parameters, several studies in the last decade have demonstrated that Sh and Pp are in fact coupled. However, the nature of this coupling relationship remains poorly understood. In this paper, we explore the influences of the spatial pore pressure distribution on Sh/Pp coupling and then on failure pressure predictions and trap integrity evaluation. With analytical models, we predict the fluid pressure sustainable within a reservoir before failure of its overpressured shale cover. We verify our analytical predictions with experiments involving analogue materials and fluids. We show that hydraulic fracturing and seal breach occur for fluid pressure greater than it would be expected from conventional retention capacity. This can be explained by the impact of the fluid overpressure field in the overburden and the pressure diffusion around the reservoir on the principal stresses. We calculate that supralithostatic pressure could locally be reached in overpressured covers. We also define the retention capacity of a cover (RC) surrounding a fluid source or reservoir as the difference between the failure pressure and the fluid overpressure prevailing in shale at the same depth. In response to a localized fluid pressure rise, we show that the retention capacity does not only depend on the pore fluid overpressure of the overburden but also on the tensile strength of the cover, its Poisson’s ratio, and the depth and width of the fluid source.  相似文献   

9.
Both analytical (small time expansion) and numerical (finite-difference) approaches have been used to solve the earthquake-induced nonlinear hydrodynamic pressure acting on a rigid high rise offshore cylinder. For the high rise offshore cylinder, the most part of the flow field is independent of z and a three dimensional hydrodynamic analysis can be reduced to a two dimensional analysis. At onset, the dimensionless ground displacement ?2 = 0 for the two dimensional analysis, the normalized hydrodynamic pressures across cylinder face is a constant and is independent of the radius of the cylinder. The normalized horizontal force coefficient Cfx is independent of intensity of ground acceleration and is approximately linear and proportional to ?2 and its onset value is equal to π. For a linear analysis i.e. neglecting nonlinear convective acceleration, the normalized hydrodynamic pressure coefficient is also independent of the radius of cylinder. The analytical method was good for ground motion in a single direction, the results of simultaneous action of two components of ground acceleration can be obtained by the superposition of the results due to separate excitation. But the superposition method is only valid in the linear analysis. For highly nonlinear problem, the present finite difference approach is recommended.  相似文献   

10.
重力锚锚固是一种常见的锚固形式。为了能够提供足够的水平承载力,传统型式的重力锚普遍比较笨重,在上拔回收时会产生较大的竖向吸附力,不利于重复利用。针对此问题,设计了一种新型铰接式重力锚,并阐述了其铺设与回收方案。其次采用有限元方法对其整体强度进行了校核,结果均符合规范。最后基于模型试验,对铰接式重力锚在黏土中的运动过程进行了研究,进而确定了其在黏土中的水平承载力和回收时的上拔力。结果表明：相较于传统重力锚,新型铰接式重力锚在确保水平承载性能的基础上,能够大幅减小上拔力,从而有效地降低铺设和回收作业的难度,且可适应多种海底土质,但该锚型仅适用于悬链线式系泊系统。相关研究结果可为实际工程中铰接式重力锚的设计提供参考。  相似文献   

11.
A one and a half layer inviscid hydraulic model was introduced to study the dynamics of the flow that brings the bottom cold water southward into the Korea Strait. Two different channel geometries were considered; a rectangular channel and a channel with a sloping western wall, which represents the continental slope near the Korean coast. The lower layer water in the rectangular channel separates from the eastern wall when the depth of the channel,H o, becomes shallower than a critical value donwstream. Hydraulic control of the flow is possible after the flow separation, if the channel becomes shallow enough. Before hydraulic control, the width of the flow decreases asH o decreases, but the effect of the slope of the western wall is negligible. After the control, however, the width increases asH o decreases or the slope becomes weaker. If the slope becomes weak enough or the channel becomes deep enough, which is determined by upstream conditions, the lower layer is observed only over the sloping western wall. This simple model shows that the continental slope between the East Sea (Japan Sea) and the Korea Strait makes the southward flowing North Korean Cold Water bank against the Korean coast in the Korea Strait. The model also shows that the sloping bottom near the Korean coast makes the bottom cold water of the Korea Strait appear only over the continental slope away from the trough of the strait.  相似文献   

12.
Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.  相似文献   

13.
Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.  相似文献   

14.
The estimation of the sealing capability of cap rocks dynamically is one of the fundamental geological problems that must be resolved in petroleum exploration. In this paper, a porosity–capillary pressure (ϕ–Pc) method was used to estimate the sealing capacity during cap rock burial and a permeability–capillary pressure (K–Pc) plus over-consolidation ratio (OCR) method to estimate the sealing capacity during uplift. Based on 120 capillary pressure–porosity measurements, a ϕ–Pc mathematical model has been established for the burial phase. By analyzing the permeability data measured from 12 mudstone/shale samples from different stratigraphic intervals under step loading conditions, a permeability–confining pressure (K–P) mathematical model has been constructed. Moreover, capillary pressure–permeability data measured from 141 mudstone or shale cap rocks have been used to establish a K–Pc mathematical model for seal capacity evaluation during uplift. Additionally, the OCR of mudstone or shale was calculated from the results of reconstructed burial and uplift histories. These mathematical models were used in case studies in the Sichuan Basin, South China. The results indicate that capillary pressure (Pc) is inadequate in evaluating sealing capacity of cap rocks but the combination of parameters Pc and OCR works well. The agreement between calculated and measured values shows the effectiveness and reliability of the models for dynamic estimation of the sealing capacity of mudstone/shale cap rocks established in this study.  相似文献   

15.
Abstract

This paper presents the results of a series of model tests performed to study the shaft capacity of pre-bored grouted planted nodular (PGPN) pile in dense sand. The influence of the vertical overburden pressure on the shaft capacity of the PGPN pile is also investigated based on the test results. The test piles were equipped with strain gauges to measure the axial loads during the loading process, moreover, a foam plate was buried beneath pile tip to eliminate the influence of tip resistance on the shaft capacity. Some conclusions can be drawn based on the test results: the peak skin friction of PGPN pile increases with the increase of vertical overburden pressure applied on the foundation soil, while the rate of increase decreases with the increasing overburden pressure; the surface of the pile–soil interface of PGPN pile is relatively rough, and significant dilatant increase in lateral stress occurs during the loading process.  相似文献   

16.
Deep cement mixing (DCM) technique is a deep in-situ stabilization technique by mixing cement powder or slurry with soft soils below the ground surface to improve their properties and behavior. Some of DCM treated soft soil grounds are approximately in a plane-strain condition; for example, a fill embankment on DCM improved ground. In this study, a plane-strain physical model was created with instrumentation and used to investigate the bearing capacity and failure mode of a soft soil improved by an end-bearing DCM column group. This study focuses on the observed wedge-shaped shear failure of the model ground and attempts to give an account of the failure. Two different methods are used to calculate the bearing capacity of the model ground, and the computed values are compared with the measured ones. It is found that the simple Brom's method gives a better estimate of the bearing capacity of the present model ground. It is also found that measured data of pore water pressures at different locations in the soft soil indicate coupling between failure of columns and consolidation of the soft soil. This study has presented the first time that a wedge-shaped block failure was observed for pattern of DCM treated soil ground.  相似文献   

17.
The results of a number of laboratory model tests for the short‐term ultimate uplift capacity of a circular plate anchor embedded in saturated soft kaolinite and montmorillonite are presented. The tests were conducted with and without venting the bottom of the plate anchor in order to determine the variation of the suction force with embedment ratio. The variation of the suction force is presented in terms of the undrained shear strength of the clay and also the net ultimate uplift capacity.  相似文献   

18.
Undrained bearing capacity of spudcan under combined loading   总被引：1，自引：0，他引：1  
The bearing capacities of spudcan foundation under pure vertical (V),horizontal (H),moment (M) loading and the combined loading are studied based on a series of three-dimensional finite element analysis.The effects of embedment ratio and soil non-homogeneity on the bearing capacity are investigated in detail.The capacities of spudcan under different pure loading are expressed in non-dimensional bearing capacity factors,which are compared with published results.Ultimate limit states under combined loading are presented by failure envelopes,which are expressed in terms of dimensionless and normalized form in three-dimensional load space.The comparison between the presented failure envelopes and available published numerical results reveals that the size and shape of failure envelopes are dependent on the embedment ratio and the non-homogeneity of the soil.  相似文献   

19.
Waterfront structures such as seawalls, dikes, and levees are frequently subjected to scouring at the toe of the slope, leading to deteriorated performance and increased failure potential. To this end, some model reinforced steep-faced slopes consisting of a two-dimensional backfill were brought to failure to explore the failure mechanisms of some geosynthetic-reinforced slopes subjected to simulated toe scouring. Results of model tests indicate that in the case of shallow scouring, a reinforcement length (L) increase from 0.4 to 1.0 Ht (Ht, total height of reinforced walls) significantly increases the tolerance against toe scouring-induced failures. In this case, a local bearing capacity failure of facing is the dominant failure mode. In the case of deep scouring, an increase in L beyond 0.7 Ht provides no additional tolerance against toe scouring because the ultimate state is always associated with a global circular sliding in the unreinforced zone. Experimental values of the lateral pressure coefficient (Kt) converted from the measured reinforcement forces indicate that reinforcement forces consistently increase in response to toe scouring up to the final collapsing state and that the reinforcement forces for L?=?1.0 Ht mobilize more effectively than those for L?=?0.7 Ht.  相似文献   

20.
Dai  Guo-liang  Zhu  Wen-bo  Zhai  Qian  Gong  Wei-ming  Zhao  Xue-liang 《中国海洋工程》2020,34(2):267-278
Suction caisson foundations are often subjected to vertical uplift loads, but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion. In order to study the uplift bearing mechanism and failure mode of suction caisson foundation, a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode. Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity. The smaller the permeability coefficient is, the higher the residual negative pressure will be. And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson. When the load reaches the ultimate bearing capacity, both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay. Combined the uplift bearing characteristics of caisson in sandy soil and soft clay, the bearing capacity composition and the calculation method are proposed. It can provide a reference for the engineering design of suction caisson foundation under vertical load.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号