首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 562 毫秒
1.
To enable detailed investigations of early stage hydrothermal plume formation and abiotic and biotic plume processes we developed a new oceanographic tool. The Suspended Particulate Rosette sampling system has been designed to collect geochemical and microbial samples from the rising portion of deep-sea hydrothermal plumes. It can be deployed on a remotely operated vehicle for sampling rising plumes, on a wire-deployed water rosette for spatially discrete sampling of non-buoyant hydrothermal plumes, or on a fixed mooring in a hydrothermal vent field for time series sampling. It has performed successfully during both its first mooring deployment at the East Pacific Rise and its first remotely-operated vehicle deployments along the Mid-Atlantic Ridge. It is currently capable of rapidly filtering 24 discrete large-water-volume samples (30–100 L per sample) for suspended particles during a single deployment (e.g. >90 L per sample at 4–7 L per minute through 1 μm pore diameter polycarbonate filters). The Suspended Particulate Rosette sampler has been designed with a long-term goal of seafloor observatory deployments, where it can be used to collect samples in response to tectonic or other events. It is compatible with in situ optical sensors, such as laser Raman or visible reflectance spectroscopy systems, enabling in situ particle analysis immediately after sample collection and before the particles alter or degrade.  相似文献   

2.
The construction and testing of a low cost, simple, intertidal and sub-tidal pore water sampler for use in sandy and muddy substrates are described in this note. The sampler, “porextractor”, is made of polyvinyl chloride (PVC) plumbing materials that can be readily sourced at any local hardware shop and costs AU $ 15.00 to build. The only mechanical component of the porextractor is a plunger that is used only once at the time of deployment. The porextractor has been designed for use on seagrass beds to collect pore water samples with minimal disturbance to the substratum for nutrient flux studies. The relative efficiency of the porextractor was tested against the widely used “Winger and Lasier” sampler, a vacuum operated diffuser stone pore water sampler. The two samplers were compared for the volume of pore water collected in sandy and muddy substrates in the laboratory, and the concentrations of total nitrogen and total phosphorus in samples collected from a sandy substrate in Amphibolis and Posidonia seagrass meadows off the Adelaide coast. While the porextractor and the Winger and Lasier samplers worked equally well in the sandy sediments, the porextractor was more efficient than the latter in muddy sediments, where clogging was a major problem. In addition, there were no significant differences (p ≤ 0.05) in the concentrations of total nitrogen and total phosphorus measured from the pore water samples collected by the two samplers in situ from the seagrass bed. The simplicity, ease of construction, non-substrate specificity, and large sample volume yield are some of the major merits of the porextractor over other conventional techniques used for pore water sampling.  相似文献   

3.
A new type ofin situ filtration sampler is described. The all Teflon sampler is hung on a nylon rope attached to a steel wire (Fig. 3). By dropping a messenger, the sampler piston is pulled down by a released weight of 50 kg, and the sampler is filled with about 400 ml of filtered water. The sample is not contaminated by metals because there is no metal around the sampler.  相似文献   

4.
A Remotely Operated Serial Sampler for Collecting Gas-Tight Fluid Samples   总被引：1，自引：1，他引：0  
This paper describes the design, construction and preliminary test results for a gas-tight serial sampler intended to be deployed at seafloor for long-term operation to take time-series fluid samples from deep-sea environments such as cold seeps, water column and hydrothermal vents. The serial sampler is a modular system that is based on independent and identical sampling modules, which are designed to collect six 160 ml gas-tight fluid samples maintained at high pressure to a depth of 4000 meters. With two working modes, the sampler can be deployed either with seafloor cabled observatory for remote control or as a stand-alone device for autonomous operation. A prototype of the instrument has been constructed and tested on the MARS cabled observatory for two months. The laboratory and field tests proved the success of the design and construction of the serial sampler, and indicated the potential for future ocean sciences.  相似文献   

5.
Abstract

The Haamer vibrocorer is a cheap and easily handled sampler for containing continuous cohesive or cohesionless sediment cores. This vibrocorer can be handled on board an ordinary trawler or small vessel. The penetration of the sampling barrel is actuated by two synchronized vibrators. Additional penetration force is provided by the buoyancy of a guiding buoy. To extend the maximum sampling length and to decrease the degree of disturbance, the vibrocorer is equipped with a plastic foil, which encases the core as it enters the liner and reduces inside friction. By providing the sampler with jetting water, the necessary penetration force is decreased. Testing a prototype is always difficult, but a working cycle of up to three cores an hour has been reached using a 6 m vibrocorer. A limited investigation has been conducted to determine the quality of the recovered cores; however, because of the poorly defined quality of the reference samples, no definitive answer to the question of sample disturbance can be given.  相似文献   

6.
A new, automatic hydrothermal fluid sampler using a shape-memory alloy   总被引：2，自引：0，他引：2  
A new hydrothermal fluid sampler has been developed to provide more maneuverability in underwater operation. The sampler characteristically employs a shape-memory alloy, which senses high temperature and actuates the suction mechanism. A shape-memory alloy is also used to switch the intake valve of the sampler, the intention being to avoid missampling when the inlet is in low temperature water. Prototype samplers were designed to collect the fluids hotter than 80°C. Test sampling was performed at hydrothermal vents (1372–1374 m deep) in the submarine volcano, Suiyo Seamount, Izu-Bonin Arc, northwestern Pacific. Observed fluid temperature was between 138 and 298°C, while the ambient seawater temperature was 3.1°C. Each prototype collected about 100 ml fluid as designed. The magnesium concentration in the samples indicated a seawater content of 47.5–90.8%, which indicates the entrainment of ambient seawater. Microscopic observatinn revealed the occurrence of microorganisms in the sample fluids at a population density of 105 to 106 cells ml−1, which is 2–3 orders of magnitude higher than those in seawater at that depth. The use of the newly developed fluid sampler will greatly facilitate the collection of vent-associated microorganisms, which are of potential biological and biotechnological interest.  相似文献   

7.
水库水质监测是水库水质评价的重要依据,通常需要现场采水样后带回实验室进行检测与分析。然而一些特殊情况下,例如库区无船、情况复杂等,只能获得沿岸水样,导致水质监测结果无法代表水库整体水质质量。本文针对水库的水样离岸采集,基于自研发的无人船系统,设计集成了采水泵,并利用无人船位点跟踪技术,实现了远距离定点遥控采水样功能。在青岛棘洪滩水库,利用该系统,设置了两个采样点(离岸50 m和离岸1300 m),并成功获取了水样。在实验室内,利用分光光度计、离子色谱仪、电感耦合等离子体质谱仪等设备,完成了所采集水样的水质分析。实验结果表明,无人船应用于水库水样离岸采集具有可行性、实用性。  相似文献   

8.
We report results from the first deployment of a buoy-mounted aerosol sampler on the Bermuda Testbed Mooring (BTM) in the Sargasso Sea, in which a time-series of 21 aerosol samples were collected over the period May 5–September 29, 2004. These aerosol samples were analyzed for iron and soluble sodium (as a proxy for sea salt). Also analyzed was a time-series of 22 aerosol samples collected over the same period at the Tudor Hill atmospheric sampling tower on Bermuda. The buoy sampler worked as intended and successfully collected a time-series of aerosol samples, thus demonstrating that moored buoys can be used as oceanic observatories to provide information on the temporal (weekly, monthly and seasonal) variability in the concentration of aerosol iron (and other trace elements) over the surface ocean. The magnitude and time variation of aerosol Fe concentrations calculated from the BTM buoy samples are in close agreement with the corresponding aerosol Fe record from the Tudor Hill tower, which is located approximately 80 km northwest of the mooring site. Both the BTM and Tudor Hill samples record periods of high aerosol iron loadings in late June and late July 2004, reflecting the transport of soil dust from North Africa, with the highest concentration of aerosol iron at the BTM site (0.83 μg m−3) measured in late June. Concentrations of sea-salt aerosol calculated from the BTM samples are comparable to values measured over the Sargasso Sea and for samples collected at the Tudor Hill tower. Sea-salt aerosols do not appear to impede the collection of mineral aerosols by the buoy-mounted sampler.  相似文献   

9.
《Marine Chemistry》2007,103(1-2):172-184
Here we report on temporal changes in the concentration and composition of lignin phenols in high molecular weight (< 0.2 μm, > 1 kDa) dissolved organic matter (HMW DOM) collected from the lower Mississippi and Pearl Rivers (MR and PR) (USA). Monthly water samples were collected at a station in the lower reach in each river from August 2001 to August 2003. Significantly higher concentrations of lignin and Λ8 values (mg lignin phenols in 100 mg organic carbon) in the Pearl River than in the Mississippi River, reflected sporadic inputs of terrestrial DOM during rainstorm events from wetlands and forest soils. Larger seasonal variations in lignin concentration and composition in the Pearl River, compared to the Mississippi River, were attributed to shifts in organic matter sources from topsoil inputs during rainstorm events to groundwater inputs and in situ production during base flow in this small river. Conversely, lower Λ8 and vanillic acid to vanillin ratios [(Ad/Al)v] in the HMW DOM of the lower Mississippi River may be a result of a lower export rate of lignin from agricultural soils due to lower carbon storage in the expansive agricultural systems of the Mississippi River watershed, as well as dilution of phytoplankton DOM inputs. Large seasonal changes in lignin concentration and Λ8 (linked at times with river discharge), and minimal variability in the composition of lignin phenols, likely represented an integrated signal of soil-derived vascular inputs from the upstream drainage basin. If we are to better understand the controls of organic matter delivery to the coastal zone from both small and large rivers, sampling strategies need to be adjusted to account for the different scales of hydrologic response time and in situ processing associated with different residence times.  相似文献   

10.
As a major aldehyde pollutant widely existing in industry and our daily life, acetaldehyde is more and more harmful to human health. As characteristic habitat niche, bacteria from deep sea environments are abundant and distinctive in heredity, physiology and ecological functions. Thus, the development of acetaldehyde-degrading bacteria from deep sea provides a new method to harness acetaldehyde pollutant. Firstly, in this study,acetaldehyde-degrading bacteria in the deep sea water of the West Pacific Ocean were enriched in situ and in the laboratory respectively, and then the diversity of uncultured bacteria was studied by using 16 S r RNA genes. Then acetaldehyde-degrading strains were isolated from two samples, including enrichment in situ and enrichment in laboratory samples of deep sea water from the West Pacific Ocean using acetaldehyde as the sole carbon source,and then the ability of acetaldehyde degradation was detected. Our results showed that the main uncultured bacteria of two samples with different enrichment approaches were similar, including Proteobacteria,Actinobacteria, Firmicutes, Cyanobacteria, but the structure of bacterial community were significant different.Four subgroups, α, γ, δ and ε, were found in Proteobacteria group. The γ-Proteobacteria was dominant(63.5%clones in laboratory enriched sample, 75% clones in situ enriched sample). The species belonged to γ-Proteobacteria and their proportion was nearly identical between the two enrichment samples, and Vibrio was the predominant genus(45% in laboratory enriched sample, 48.5% in situ enriched sample), followed by Halomonas(9% in situ enriched sample) and Streptococcus(6% in laboratory enriched sample). A total of 12 acetaldehyde-degrading strains were isolated from the two samples, which belonged to Vibrio, Halomonas,Pseudoalteromonas, Pseudomonas and Bacillus of γ-Proteobacteria. Strains ACH-L-5, ACH-L-8 and ACH-S-12,belonging to Vibrio and Halomonas, have strong ability of acetaldehyde degradation, which could tolerate 1.5 g/L acetaldehyde and degrade 350 mg/L acetaldehyde within 24 hours. Our results indicated that bacteria of γ-Proteobacteria may play an important role in carbon cycle of deep sea environments, especial the bacteria belonging to Vibrio and Halomonas and these strains was suggested for their potentials in government of aldehyde pollutants.  相似文献   

11.
A suction sediment sampler has been developed for sampling suspended sand in the field. It works by the pressure difference between seabed and water surface, and thus no pump is required. The fact that the sampler has no mechanical moving parts and no electronics makes it very dependable. Seven samples are taken simultaneously at different elevations starting at about 1 cm above the bed. The sampling time is about 3 min for water depths of about 1.5 m. Sixty-five concentration profiles, complete with hydraulic data and sediment characteristics are given in the appendix.  相似文献   

12.
A quick and effective underwater quantitative quadrat sampler was designed for sampling macrobenthic epifauna on hard substrates. Using a 400 cm2 quadrat, divers could take samples quickly and with little or no loss of organisms. The sampler can be used successfully in adverse conditions in the open ocean on any relatively flat substrate, regardless of its orientation.  相似文献   

13.
To ensure that destructive bottom fishing activities do not have significant adverse impacts on Vulnerable Marine Ecosystems (VMEs) in high seas areas of the World Ocean, as required by United Nations General Assembly Resolution 61–105, knowledge of the locations of VMEs is required. Quantifying the occurrence and abundance of VME indicator taxa in research bottom-trawl samples, as well as from in situ observations with underwater photography, provides methods for detecting these ecosystems. A case study is presented in which a threshold density of indicator taxa was used as the basis for VME designation. In 2009, high densities of VME indicator taxa were encountered at 11 sites off th`e South Orkney Islands in the Atlantic sector of the Southern Ocean. In most cases, thresholds were exceeded by a limited number of VME indicator taxa, primarily representatives of the class Demospongiae (siliceous sponges), Hexactinellida (glass sponges) and Ascidiacea (tunicates). In situ imagery further showed the importance of bryozoans (lace corals), scleractinians (stony corals) and stylastrids (hydrocorals) in the study region. The approach outlined here, which relies on widely used sampling techniques, could be employed throughout the World Ocean to detect and document the presence of VMEs from existing datasets. To illustrate this point, the method was applied to a separate dataset, collected in 2006, from a research cruise off the northern Antarctic Peninsula, which led to the detection of 17 VMEs. The VMEs from both the 2006 and 2009 data are now registered and influence the management of fisheries in the Southern Ocean.  相似文献   

14.
Four methods were compared for the integration of14C-primary productivity per m2; (1) thein situ method at 0, 2.5, 5, 7.5, 10 and 12.5 m (standard depths 1); (2) thein situ method at 0, 5, 10 and 12.5 m (standard depths 2); (3) thein situ method at 2.5, 7.5 and 11.5 m for each sample pumped over depth intervals 0 to 5 m, 5 to 10 m, and 10 to 12.5 m, respectively (integrated depths); and (4) the simulatedin situ method for samples collected from light standard depths. The method which appeared to give the most reliable results was that (3) in which samples were averaged by pumping water over the euphotic depth followed by incubation of integrated samples at the middle of each depth interval.  相似文献   

15.
A realtime monitoring system for observing physical, biological, and optical oceanographic parameters in shallow waters was developed. It consists of a CTD with oxygen sensor, anin situ fluorometer, anin situ transmissometer, and anin situ quanta meter together with an on-deck quanta meter. The system is also equipped with a water sampling device. Water sampling can be done during the upward cast on the basis of depth profiles of temperature, salinity, oxygen,in situ fluorescence, transmittance, and underwater irradiance taken during the downward cast.  相似文献   

16.
This paper describes an atmospheric correction algorithm for Geostationary Ocean Color Imager (GOCI) and its early phase evaluation. This algorithm was implemented in GOCI Data Processing System (GDPS) version 1.1. The algorithm is based on the standard SeaWiFS method, which accounts for multiple scattering effects and partially updated in terms of turbid case-2 water correction, optimized aerosol models, and solar angle correction per slot. For turbid water correction, we used a regional empirical relationship between water reflectance at the red (660 nm) and near infrared bands (745 nm and 865 nm). The relationship was derived from turbid pixels in satellite images after atmospheric correction, and processed using aerosol properties derived for neighboring non-turbid waters. For validation of the GOCI atmospheric correction, we compared our results with in situ measurements of normalized water leaving radiance (nL w ) spectra that were obtained during several cruises in 2011 around Korean peninsula. The match up showed an acceptable result with mean ratio of the GOCI to in situ nL w (??), 1.17, 1.24, 1.26, 1.15, 0.86 and 0.99 at 412 nm, 443 nm, 490 nm, 555 nm, 660 nm and 680 nm, respectively. It is speculated that part of the deviation arose from a lack of vicarious calibration and uncertainties in the above water nLw measurements.  相似文献   

17.
Ice effects have caused extensive damage. Enormous forces have been recorded. On the other hand, ice has been used as a structural material under various situations. To use ice beneficially and to assess the danger of ice forces, it is necessary to know the mechanical properties of ice.Results from the large number of ice tests carried out in laboratories show the difficulties of sampling and testing procedures. Most of the tests have not reproduced faithfully enough the conditions existing in nature. To obtain adequate results, laborious and slow samplings and preparations of test specimens have been necessary. Recently, extensive use has been made of in situ tests in order to reduce the number of factors whixh can induce errors in measurements. Large scale tests have simulated actual structures. General ice properties have become available from small-scale in situ tests. Since these tests give rapid results, a large number are already available with a good coverage of field conditions.A theoretical basis has been devised for these in situ tests which measure essentially the unconfined and confined compressive strengths of ice, and practical devices have been developed to execute these tests. A correlation of measurements from laboratory tests and in situ tests has established a link between natural and artificial environments. Brittle elastic and clastic theories have been applied, to find the best correlations for ice tests. Test results have been related to the mechanical properties as used in engineering practice.A very summary conclusion of results is that cold sea ice and cold fresh water ice are both very strong. However, depending on the load rate, ice can be quite brittle, which mitigates dangerous effects from ice action against massive structures.  相似文献   

18.
Bleaching and associated mortality is an extreme threat to the persistence of coral populations in the projected warming regime of the next few decades. Recent evidence indicates that thermal bleaching thresholds may be affected by water quality gradients. The unexpected encounter of a coral mass bleaching event at a remote, uninhabited Caribbean island (Navassa) during a routine reef assessment cruise in November 2006 provided the opportunity to characterize bleaching responses and thermal exposure in an oceanic area with negligible continental influence or human impact on water quality. The coral taxa most susceptible to bleaching were Agaricia spp. and Montastraea faveolata. Siderastraea siderea, Diploria spp. and Porites porites were intermediately affected, while Porites astreoides and Montastraea cavernosa were minimally affected and negligible bleaching was observed in Acropora palmata. Bleaching prevalence (colonies > 4 cm diameter) ranged from 0.16 to 0.63 among sites. Deeper sites (between 18 and 37 m) had significantly higher prevalence of bleaching than shallow sites (<10 m). This general pattern of more bleaching in deeper sites also occurred within species. Though exposure to high-temperature stress was not greater at deeper sites, water motion, which may bolster bleaching resistance, was likely less. In situ loggers indicated temperatures over 30 °C initiated at shallow sites in mid-August, at deeper sites in early September, and were persistent at all sites until mid-October. Long term (1983–2007) climatologies constructed from AVHRR SSTs suggest that the mass bleaching event observed at Navassa in 2006 corresponded with greater intensity and duration of warm temperature anomalies than occurred in 2005, for which no in situ observations (bleaching nor temperature) are available.  相似文献   

19.
We present a 3-year multidisciplinary biogeochemical data set taken in situ at the Porcupine Abyssal Plain (PAP) time-series observatory in the Northeast Atlantic (49°N, 16.5°W; water depth ∼4850 m) for the period 2003 to 2005. The high-resolution year-round autonomous measurements include temperature, salinity, chlorophyll-a (derived from in situ chlorophyll-fluorescence) and inorganic nitrate, all at a nominal depth of 30 m on an Eulerian observatory mooring. This study compares these in situ time-series data with satellite chlorophyll-a data, regional data from a ship of opportunity, mixed-layer depth measurements from profiling Argo floats and lateral advection estimates from altimetry. This combined and substantial data set is used to analyse seasonal and inter-annual variability in hydrography and nitrate concentrations in relation to convective mixing and lateral advection. The PAP observatory site is in the inter-gyre region of the North Atlantic where convective mixing ranges from 25 m in the summer to over 400 m in winter when nutrients are supplied to the surface. Small inter-annual changes in the winter mixed layer can result in large changes in nitrate supply and productivity. However the decrease in maximum winter nitrate over the three-year period, from 10 to 7 mmol m−3, cannot be fully explained by convective mixing. Trajectories leading to the PAP site, computed from altimetry-derived geostrophic velocities, confirm that lateral advection cannot be ignored at this site and may be an important process along with convective mixing. Over the three years, there is an associated decrease in new production calculated from nitrate assimilation from 85.4 to 40.3±4.3 gCm−2 a−1. This confirms year-to-year variability in primary production seen in model estimates for the region. The continuous in situ dataset also shows inter-annual variation in the timing of the spring bloom due to variations in heat flux; the 2005 bloom occurred earlier than in 2004.  相似文献   

20.
Fish populations in estuaries are often monitored with traditional sampling gears such as trawls. Trawling is relatively expensive and may be hindered by environmental conditions such as tides and substrates. Power station cooling-water intake screens have been effectively used as estuarine fish sampling devices for many years, but very few quantitative comparisons of intake fish-catch characteristics with samples from other collection methods have been made. Fish collected at the cooling-water intake of a large power station in the lower Forth estuary, UK, were more similar in assemblage composition to fish caught by nearby pelagic trawling than to fish caught by Agassiz (demersal) trawling, mostly because the intake and pelagic-trawl catches were largely composed of clupeids (Sprattus sprattus and Clupea harengus). The intake catch was typified by pelagic, demersal, and benthic species, however, and was less variable than the catches made by the two trawls. Monthly trends in relative abundance correlated reasonably well between the intake and trawl samples. Fish collected at the intake tended to be significantly smaller than those collected by trawling, which was probably attributable to the intake's smaller mesh size. The study highlighted the utility of a cooling-water intake as an efficient, low-cost fish sampling device, which should be considered as an alternative to trawling as the cost of the latter increases into the future.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号