共查询到20条相似文献，搜索用时 421 毫秒
1.
Hidemi Tanaka Shin-Ichiro Hinoki Kazuo Kosaka Aiming Lin Keiji Takemura Akihiro Murata Takao Miyata 《Island Arc》2001,10(3-4):381-391
Abstract This paper describes the results of petrographical and meso- to microstructural observations of brittle fault rocks in cores obtained by drilling through the Nojima Fault at a drilling depth of 389.52 m. The zonation of deformation and alteration in the central zone of the fault is clearly seen in cores of granite from the hanging wall, in the following order: (i) host rock, which is characterized by some intragranular microcracks and in situ alteration of mafic minerals and feldspars; (ii) weakly deformed and altered rocks, which are characterized by transgranular cracks and the dissolution of mafic minerals, and by the precipitation of zeolites and iron hydroxide materials; (iii) random fabric fault breccia, which is characterized by fragmentation, by anastomosing networks of transgranular cracks, and by the precipitation of zeolites and iron hydroxide materials; and (iv) fault gouge, which is characterized by the precipitation of smectite and localized cataclastic flow. This zonation implies that the fault has been weakened gradually by fluid-related fracturing over time. In the footwall, a gouge layer measuring only 15 mm thick is present just below the surface of the Nojima Fault. These observations are the basis for a model of fluid behavior along the Nojima Fault. The model invokes the percolation of meteoric fluids through cracks in the hanging wall fault zone during interseismic periods, resulting in chemical reactions in the fault gouge layer to form smectite. The low permeability clay-rich gouge layer sealed the footwall. The fault gouge was brecciated during coseismic or postseismic periods, breaking the seal and allowing fluids to readily flow into the footwall, thus causing a slight alteration. Chemical reactions between fluids and the fault breccia and gouge generated new fault gouge, which resealed the footwall, resulting in a low fluid condition in the footwall during interseismic periods. 相似文献
2.
3.
Abstract The 1999 Chi-Chi earthquake in Taiwan ( M w = 7.6) produced a surface rupture along the north–south-striking Chelungpu thrust fault with pure dip-slip (east side up) and left lateral strike-slip displacements. Near-field strong-motion data for the northern part of the fault illustrate a distinct lack of the high-frequency seismic radiation associated with a large slip (10–15 m) and a rapid slip velocity (2–4 m/s), suggesting a smooth seismic slip associated with low dynamic frictional resistance on the fault. A drillhole was constructed at shallow depths in the possible fault zones of the northern part of the Chelungpu Fault, which may have slipped during the 1999 earthquake. One of the zones consists of a 20-cm-thick, unconsolidated fault breccia with a chaotic texture lacking both discrete slip surfaces (e.g. Riedel shears) and grain crushing. Other possible fault zones are marked by the narrow (less than a few centimeters) gouge zone in which clayey material intrudes into the damaged zone outside of the gouge zone. These characteristic fault rock textures suggest that the slip mechanisms at shallow levels during the earthquake involved either granular flow of initially unconsolidated material or slip localization under elevated pore pressure along the narrow clayey gouge zone. Because both mechanisms lead to low dynamic frictional resistance on the fault, the rapid seismic slip in the deep portions of the fault (i.e. the source region of strong-motion radiation) could have been accommodated by frictionless slip on the shallow portions of the fault. The combination of strong-motion data and fault rock analysis suggests that smooth slip associated with low dynamic friction occurred on both the deep and shallow portions of the fault, resulting in a large slip between the source region and the surface in the northern region. 相似文献
4.
Internal structure of Longmenshan fault zone at Hongkou outcrop,Sichuan, China,that caused the 2008 Wenchuan earthquake 
下载免费PDF全文
下载免费PDF全文 This paper reports the internal structures of the Beichuan fault zone of Longmenshan fault system that caused the 2008 Wenchuan earthquake, at an outcrop in Hongkou, Sichuan province, China. Present work is a part of comprehensive project of Institute of Geology, China Earthquake Administration, trying to understand deformation processes in Longmenshan fault zones and eventually to reproduce Wenchuan earthquake by modeling based on measured mechanical and transport properties. Outcrop studies could be integrated with those performed on samples recovered from fault zone drilling, during the Wenchuan Earthquake Fault Scientific Drilling (WFSD) Project, to understand along-fault and depth variation of fault zone properties. The hanging wall side of the fault zone consists of weakly-foliated, clayey fault gouge of about 1 m in width and of several fault breccia zones of 30–40 m in total width. We could not find any pseudotachylite at this outcrop. Displacement during the Wenchuan earthquake is highly localized within the fault gouge layer along narrower slipping-zones of about 10 to 20 mm in width. This is an important constraint for analyzing thermal pressurization, an important dynamic weakening mechanism of faults. Overlapping patterns of striations on slickenside surface suggest that seismic slip at a given time occurred in even narrower zone of a few to several millimeters, so that localization of deformation must have occurred within a slipping zone during coseismic fault motion. Fault breccia zones are bounded by thin black gouge layers containing amorphous carbon. Fault gouge contains illite and chlorite minerals, but not smectite. Clayey fault gouge next to coseismic slipping zone also contains amorphous carbon and small amounts of graphite. The structural observations and mineralogical data obtained from outcrop exposures of the fault zone of the Wenchuan earthquake can be compared with those obtained from the WFSD-1 and WFSD-2 boreholes, which have been drilled very close to the Hongkou outcrop. The presence of carbon and graphite, observed next to the slipping-zone, may affect the mechanical properties of the fault and also provide useful information about coseismic chemical changes. 相似文献
5.
THE GEOLOGICAL AND ROCK MECHANICAL DISTINCTION EVIDENCE BETWEEN STICK-SLIP AND CREEP IN HOST ROCK SEGMENTS OF FAULT 下载免费PDF全文
下载免费PDF全文 ZHOU Yong-sheng 《地震地质》2019,41(5):1266-1272
Paleo-seismic and fault activity are hard to distinguish in host rock areas compared with soft sedimentary segments of fault. However, fault frictional experiments could obtain the conditions of stable and unstable slide, as well as the microstructures of fault gouge, which offer some identification marks between stick-slip and creep of fault.
We summarized geological and rock mechanical distinction evidence between stick-slip and creep in host rock segments of fault, and analyzed the physical mechanisms which controlled the behavior of stick-slip and creep. The chemical composition of fault gouge is most important to control stick-slip and creep. Gouge composed by weak minerals, such as clay mineral, has velocity weakening behavior, which causes stable slide of fault. Gouge with rock-forming minerals, such as calcite, quartz, feldspar, pyroxene, has stick-slip behavior under condition of focal depth. To the gouge with same chemical composition, the deformation mechanism controls the frictional slip. It is essential condition to stick slip for brittle fracture companied by dilatation, but creep is controlled by compaction and cataclasis as well as ductile shear with foliation and small fold. However, under fluid conditions, pressure solution which healed the fractures and caused strength recovery of fault, is the original reason of unstable slide, and also resulted in locking of fault with high pore pressure in core of fault zone. Contrast with that, rock-forming minerals altered to phyllosilicates in the gouges by fluid flow through degenerative reaction and hydrolysis reaction, which produced low friction fault and transformations to creep. The creep process progressively developed several wide shear zones including of R, Y, T, P shear plane that comprise gouge zones embedded into wide damage zones, which caused small earthquake distributed along wide fault zones with focal mechanism covered by normal fault, strike-slip fault and reverse fault. However, the stick-slip produced mirror-like slide surfaces with very narrow gouges along R shear plane and Y shear plane, which caused small earthquake distributed along narrow fault zones with single kind of focal mechanism. 相似文献
6.
Yu. A. Morozov A. I. Smul’skaya A. L. Kulakovskiy M. A. Matveev 《Izvestiya Physics of the Solid Earth》2018,54(1):1-21
The results of an instrumental and analytical investigation of the products of mineral and textural transformations in the tectonic slickensides and fault gouge in the near-surface terrigenous sedimentary rocks (clays, arkose sandstones, shungites) which have undergone localized deformations in fault zones of presumably seismogenic origin are presented. Based on this, several peculiarities in the behavior of a dynamic slip in the upper transition horizon from aseismic to seismogenic mode of faulting in the Earth’s crust are elucidated. The changes in the mineral phase compositions of the fault facies against the protolith composition are estimated; the parameters of the temperature regime and thermal energy balance of deformational metamorphic reactions are determined. The probable causes of instability in the faults, the mechanisms of the loss of strength, the weakening and strengthening during seismogenic dynamic slip are considered. The role of tribochemical phenomena in the course of a rock’s transformation into a fault gouge and the related energy effects are discussed. An inventory of the possible energy costs on the processes of transforming material in dynamic slip zones is compiled. 相似文献
7.
Vladimir Lyakhovsky Amir Sagy Yuval Boneh Ze’ev Reches 《Pure and Applied Geophysics》2014,171(11):3143-3157
Slip along faults generates wear products such as gouge layers and cataclasite zones that range in thickness from sub-millimeter to tens of meters. The properties of these zones apparently control fault strength and slip stability. Here we present a new model of wear in a three-body configuration that utilizes the damage rheology approach and considers the process as a microfracturing or damage front propagating from the gouge zone into the solid rock. The derivations for steady-state conditions lead to a scaling relation for the damage front velocity considered as the wear-rate. The model predicts that the wear-rate is a function of the shear-stress and may vanish when the shear-stress drops below the microfracturing strength of the fault host rock. The simulated results successfully fit the measured friction and wear during shear experiments along faults made of carbonate and tonalite. The model is also valid for relatively large confining pressures, small damage-induced change of the bulk modulus and significant degradation of the shear modulus, which are assumed for seismogenic zones of earthquake faults. The presented formulation indicates that wear dynamics in brittle materials in general and in natural faults in particular can be understood by the concept of a “propagating damage front” and the evolution of a third-body layer. 相似文献
8.
9.
断层泥在基岩区断层新活动研究中的意义 总被引：21，自引：0，他引：21
断层泥在基岩区断层新活动研究中的意义在于：利用断层泥中粘土矿物的组合、成分、结晶程度可以判定断层活动时的物理环境；断层泥带的宽度与断层的位移量有一定的线性关系，从而可用于确定断层的位移量；断层泥的显微构造特征及其中石英碎砾的表面结构，可以提供有关断层活动方式、性质、期次、时代等重要信息。对断层泥进行包括野外详细观测、室内显微构造分析以及年龄测定在内的综合研究，是确定基岩区断层新活动特征的行之有效的方法。 相似文献
10.
Tomoyuki Ohtani Hidemi Tanaka Koichiro Fujimoto Takayuki Higuchi Naoto Tomida Hisao Ito 《Island Arc》2001,10(3-4):392-400
Abstract The internal structures of the Nojima Fault, south-west Japan, are examined from mesoscopic observations of continuous core samples from the Hirabayashi Geological Survey of Japan (GSJ) drilling. The drilling penetrated the central part of the Nojima Fault, which ruptured during the 1995 Kobe earthquake (Hyogo-ken Nanbu earthquake) ( M 7.2). It intersected a 0.3 m-thick layer of fault gouge, which is presumed to constitute the fault core (defined as a narrow zone of extremely concentrated deformation) of the Nojima Fault Zone. The rocks obtained from the Hirabayashi GSJ drilling were divided into five types based on the intensities of deformation and alteration: host rock, weakly deformed and altered granodiorite, fault breccia, cataclasite, and fault gouge. Weakly deformed and altered granodiorite is distributed widely in the fault zone. Fault breccia appears mostly just above the fault core. Cataclasite is distributed mainly in a narrow (≈1 m wide) zone in between the fault core and a smaller gouge zone encountered lower down from the drilling. Fault gouge in the fault core is divided into three types based on their color and textures. From their cross-cutting relationships and vein development, the lowest fault gouge in the fault core is judged to be newer than the other two. The fault zone characterized by the deformation and alteration is assumed to be deeper than 426.2 m and its net thickness is > 46.5 m. The fault rocks in the hanging wall (above the fault core) are deformed and altered more intensely than those in the footwall (below the fault core). Furthermore, the intensities of deformation and alteration increase progressively towards the fault core in the hanging wall, but not in the footwall. The difference in the fault rock distribution between the hanging wall and the footwall might be related to the offset of the Nojima Fault and/or the asymmetrical ground motion during earthquakes. 相似文献
11.
沂沭断裂带及其附近断裂的断层泥分形特征及其地震地质意义 总被引：7，自引：0，他引：7
利用岩石碎裂数目的分形理论，分析，计算了沂沭断裂带及其西侧北西向断裂的断层泥粒度成分的分维值，讨论了断层泥粒度成分分维的地震地质意义，研究结果表明，沂沭断裂带内的断裂活动的强度大于北西向断裂活动强度；Ｆ２是沂沭断裂带中活动最强的一条断裂，断层泥粒度成分分维值可作为表征断裂活动时代，破裂形式和断层泥形成斫代等的参量；分维值还与断层泥的母岩，厚度，粘土矿物含量和所处的断裂部位等相关。 相似文献
12.
断层岩,尤其是断层泥的磁性异常近年来被研究人员广泛关注,但关于其磁性异常的形成原因尚没有统一的解释．海原断裂是青藏高原东北缘一条重要的走滑断裂,前期研究发现海原断裂带景泰段出露有数十米至上百米的断层岩,是理想的研究材料．本研究选取海原断裂带景泰段老虎山山前一个断层岩剖面作为研究对象,拟通过测量断层岩的磁化率（χ）、非磁滞剩磁（ARM）、饱和等温剩磁（SIRM）、等温剩磁（IRM）以及磁化率随温度变化曲线（χ-T曲线）等磁学参数并结合粒度、碳含量、X射线衍射（XRD）等分析方法来探究海原断裂带老虎山段不同颜色断层岩的磁性特征及其形成机制．磁学研究显示黑色、红色及杂色断层泥相较于围岩和破碎带显示了低磁性,尤其是黑色断层泥,其磁化率值均小于10×10~(-8 )m~3·kg~(-1)．碳含量及矿物相分析结果指示黑色断层泥与断裂带附近石炭系煤层具有相似的矿物相组成,结合相似的χ-T曲线推断石炭系煤层为黑色断层泥的母岩．石炭系煤层经断层活动卷入断层,在断层强烈剪切摩擦作用下不断细化,形成伊利石等黏土矿物,并促使一部分顺磁性含铁硅酸盐矿物或其他含铁矿物发生化学变化形成亚铁磁性矿物,使得黑色断层泥的磁化率较其母岩石炭系煤层有一定升高．通过黑色断层泥的铁磁性磁化率结合χ-T曲线计算获得断层泥所经历的最高温度约为420℃,不超过450℃．老虎山段厚层碳质断层泥的存在为该地区发现的浅层蠕滑现象提供了一种解释． 相似文献
13.
Diane E. Moore David A. Lockner Hisao Ito Riuji Ikeda Hidemi Tanaka Kentaro Omura 《Pure and Applied Geophysics》2009,166(10-11):1669-1691
Samples of damage-zone granodiorite and fault core from two drillholes into the active, strike-slip Nojima fault zone display microstructures and alteration features that explain their measured present-day strengths and permeabilities and provide insight on the evolution of these properties in the fault zone. The least deformed damage-zone rocks contain two sets of nearly perpendicular (60–90° angles), roughly vertical fractures that are concentrated in quartz-rich areas, with one set typically dominating over the other. With increasing intensity of deformation, which corresponds generally to increasing proximity to the core, zones of heavily fragmented rock, termed microbreccia zones, develop between prominent fractures of both sets. Granodiorite adjoining intersecting microbreccia zones in the active fault strands has been repeatedly fractured and locally brecciated, accompanied by the generation of millimeter-scale voids that are partly filled with secondary minerals. Minor shear bands overprint some of the heavily deformed areas, and small-scale shear zones form from the pairing of closely spaced shear bands. Strength and permeability measurements were made on core collected from the fault within a year after a major (Kobe) earthquake. Measured strengths of the samples decrease regularly with increasing fracturing and fragmentation, such that the gouge of the fault core and completely brecciated samples from the damage zone are the weakest. Permeability increases with increasing disruption, generally reaching a peak in heavily fractured but still more or less cohesive rock at the scale of the laboratory samples. Complete loss of cohesion, as in the gouge or the interiors of large microbreccia zones, is accompanied by a reduction of permeability by 1-2 orders of magnitude below the peak values. The core samples show abundant evidence of hydrothermal alteration and mineral precipitation. Permeability is thus expected to decrease and strength to increase somewhat in active fault strands between earthquakes, as mineral deposits progressively seal fractures and fill pore spaces. 相似文献
14.
5.12汶川地震同震地表破裂带在虹口八角-深溪沟一带主要出露于三叠系须家河组的炭质泥岩中,同震断层泥在颜色、结构上与老断层泥和围岩类似。通过开挖探槽,系统采样,采用粉晶X射线衍射定量分析方法,研究了同震地表破裂带的围岩、断层角砾岩、老断层泥和新断层泥的矿物成分特征。同震断层泥的主要成分为石英和黏土矿物,含微量长石和白云石;断层泥的显著特征为高黏土矿物含量,从同震断层泥、老断层泥、角砾岩到围岩黏土矿物含量依次降低,黏土矿物以伊利石和伊蒙混层为主,含微量绿泥石和高岭石,矿物组成明显比地表破裂带北段同震断层泥简单。不同颜色的同震断层泥成分略有不同,黑色断层泥中伊利石含量明显高于白色断层泥;老断层泥中含有方解石和白云石,而同震断层泥不含方解石,只含微量白云石。同震断层泥中伊蒙混层高含量表明,在本次地震错动中有富含K的流体参与。 相似文献
15.
本文对郯庐断裂带大水场黄绿色粘土型断层泥进行了一系列实验研究并初步探讨了其本构特征。该本构模型能描述断层泥的弹性性态。破坏性态和帽盖性态,适应范围较广。 相似文献
16.
断裂带物质组成、结构及其物理性质是理解断裂变形机制和地震破裂过程的基础和关键,断裂带地震（黏滑）和非地震（蠕滑）滑移行为不仅对了解地震活动性和山脉隆升过程具有重要意义,而且直接为防震减灾提供科学依据.我们以穿过龙门山映秀—北川和灌县—安县断裂带的汶川地震断裂带科学钻探（WFSD）岩心和地表出露的断裂带为研究对象,通过对断裂岩组成、结构、显微构造和钻孔物性测井数据进行分析研究,确定了龙门山逆冲断裂带滑移行为和物性特征,初步探讨了大地震活动性和有关断裂带的隆升作用：（1）映秀—北川断裂带倾向NW,浅部倾角~65°,发育的断裂岩厚约180~280 m,由碎裂岩、假玄武玻璃（地震化石）、断层泥和断层角砾岩组成.断裂带具有高自然伽马、高磁化率值、低电阻率、低波速等物理性质以及对称型破碎结构.断层泥普遍具有摩擦热效应的高磁化率值和石墨化作用特征,是古地震滑动的岩石记录.表明映秀—北川断裂带为经常发生大地震的断裂带,晚新生代以来类似汶川地震的大地震复发周期小于6000—10000年,具有千年复发周期特征.（2）灌县—安县断裂带倾向NW,浅部倾角~38°,发育的断裂岩厚约40~50 m,仅由断层泥和断层角砾岩组成,具有典型的"压溶"结构,表现出蠕滑性质.除压溶作用外,定向富集的层状黏土矿物和微孔隙的发育使断层强度变弱.断裂带具上盘破碎的非对称型破碎结构,除具低磁化率值特征外,其他物性与映秀—北川断裂带一致.（3）根据断裂岩厚度与断层滑移量相关经验公式关系,以及断层产状,粗略估算映秀—北川断裂带自中生代以来累积垂直位移量大于9 km,灌县—安县断裂带累积垂直位移量小于3 km.映秀—北川断裂带长期大地震产生的累积垂直位移量是龙门山隆升的主要贡献. 相似文献
17.
In this work,the fractal dimension of granulometric composition in the fault gouge from the Yishu fault zone and northwest-trending faults on its west side is calculated and studied based on the fractal theory of rock fragmentation.The seismo-geological implications of the fractal dimension of granulometric composition in fault gouges are also discussed.The results show that the Yishu fault zone is more active than the northwest-trending faults and the Anqiu-Juxian fault is the most active in the Yishu fault zone.The fractal dimension of fault gouge is a parameter describing the relative active age and rupture mode of the fault and forming age of the fault gouge.The fractal dimension value is also related to the parent rock,thickness,structural position,and clay content of the fault gouge. 相似文献
18.
Seismic measurements of the internal properties of fault zones 总被引：1，自引：0，他引：1
The internal properties within and adjacent to fault zones are reviewed, principally on the basis of laboratory, borehole, and seismic refraction and reflection data. The deformation of rocks by faulting ranges from intragrain microcracking to severe alteration. Saturated microcracked and mildly fractured rocks do not exhibit a significant reduction in velocity, but, from borehole measurements, densely fractured rocks do show significantly reduced velocities, the amount of reduction generally proportional to the fracture density. Highly fractured rock and thick fault gouge along the creeping portion of the San Andreas fault are evidenced by a pronounced seismic low-velocity zone (LVZ), which is either very thin or absent along locked portions of the fault. Thus there is a correlation between fault slip behavior and seismic velocity structure within the fault zone; high pore pressure within the pronounced LVZ may be conductive to fault creep. Deep seismic reflection data indicate that crustal faults sometimes extend through the entire crust. Models of these data and geologic evidence are consistent with a composition of deep faults consisting of highly foliated, seismically anisotropic mylonites. 相似文献
19.
断层带内的流体不仅可以通过水岩反应改变断裂岩的矿物组成和化学成分,从而导致化学性质和物理性质的变化,而且可以影响或控制断裂带的变形行为.断裂带中岩石磁学特征是由特定化学环境下磁性矿物的种类和含量所决定的,因此,从矿物学和地球化学角度探讨断裂岩的磁性变化,对揭示断层的变形行为和环境具有一定的指示作用.本文以汶川科钻WFSD-3P钻孔中龙门山灌县—安县断裂带断裂岩为研究对象,运用高分辨率磁化率测试、XRD矿物成分半定量分析、XRF元素扫描以及不同价态Fe元素含量分析等多种方法开展断层磁学变化和变形环境的研究.磁化率测试结果表明灌县—安县断裂带断层泥的磁化率值普遍低于对应的围岩磁化率平均值.结合前人研究成果表明造成该断层泥低磁化率异常的原因是在间震期的长期流体作用下,铁磁性矿物（例如磁铁矿）转变成顺磁性矿物（铁硫化物、菱铁矿或含铁的黏土矿物）.新生铁硫化物和含铁黏土矿物是在间震期缓慢形成的,而黏土矿物含量的增加弱化了断层强度,促进断层蠕滑,这说明断层泥低磁化率异常可能指示了该断裂在间震期长期缓慢活动,即为蠕滑变形.断层泥中黄铁矿的发育和高Fe2+和S元素、低Fe3+的特征显示灌县—安县断裂作用环境通常是在低温、还原环境中进行的.这些结果与低磁化率值的相关性暗示断层泥低磁化率异常可能对活动断层的低温还原环境具有指示意义. 相似文献