共查询到20条相似文献，搜索用时 46 毫秒
1.
George H. Sutton Junzo Kasahara William N. Ichinose David A. Byrne 《Marine Geophysical Researches》1977,3(2):153-177
Three distinct ocean bottom seismograph (OBS) systems have been developed at the Hawaii Institute of Geophysics to satisfy the different requirements for short-range refraction and anisotropy experiments, long-range refraction experiments, and short-term and semi-permanent monitoring for earthquakes. One system, originally designed for semi-permanent use in conjunction with a monster buoy of the IDOE North Pacific Experiment has been modified for emplacement off Oahu. It contains 3-component 1 Hz seismometers and a hydrophone and obtains power and transmits data via tow conductor cable. Two additional systems were designed for short-term use: a 2 Hz telemetering system (TOBS); and 4.5 Hz free-fall pop-up system (POBS). The TOBS contains 3-component seismometers and a hydrophone and transmits data to the ship via light-weight single-conductor electromechanical cable and an HF-VHF radio link from a surface buoy. The bottom package also includes a backup tape recorder. This system exhibits the advantages of real-time data acquisition (e.g. precise timing, rapid appraisal of data quality, optimum use of explosives, and common recording with other data) and the complexities and difficulties associated with a deep-sea mooring. However, use of cable with near neutral bouyancy permits the design of a deep-water system with low weights and stress levels. The POBS is a self-contained package containing a vertical and single horizontal seismometer, hydrophone, cassette tape recorder, and pre-set timed release. This system is relatively simple and inexpensive. Total weight of 150 kg in air (before launch) permits emplacement and retrieval from a ship with no special equipment by two (strong) persons. Experience to data suggests that the optimum deployment scheme for many studies is a combination of TOBS's and POBS's.Hawaii Institute of Geophysics Contribution 835. 相似文献
2.
R. Herber 《Marine Geophysical Researches》1979,4(2):247-253
The ocean bottom seismograph (OBS) of the Institut für Geophysik, Hamburg (IfG) is designed for refraction seismic experiments and for recording microseismic noise. Hydrophone signals are recorded directly on a casette tape recorder with a band width of 3–60 Hz. Signals from three component 1 Hz seismometers are recorded on a 2nd casette tape recorder in FM for a frequency range of 0.1–1 Hz. A telemetering buoy at the surface is connected with the OBS by a polypropylene rope. 相似文献
3.
David A. Byrne George H. Sutton J. Grant Blackinton Frederick K. Duennebier 《Marine Geophysical Researches》1983,5(4):437-449
In most of the Ocean Bottom Seisometers (OBS) used today, the sensors, electronics, recorders, flotation, and ballast are contained in one rigid package. Usually this configuration requires a large mass, a large vertical cross section in the water, and relatively small bearing surface area in contact with the bottom, resulting in poor seismic characteristics and increased noise sensitivity. An OBS recently developed at the Hawaii Institute of Geophysics (HIG) minimizes these problems by physically separating the sensor from the main OBS package. Direct comparison between signals recorded by a standard HIG configuration Pop-up Ocean Bottom Seismometer (POBS) and signals from the new Isolated Sensor Ocean Bottom Seismometer (ISOBS), deployed near each other in deep water, clearly demonstrates the advantages of the isolated sensor configuration. Although the ISOBS is superior to older OBS designs, recent testing suggests that further improvements can be made. 相似文献
4.
A simple shaker table for seismometer calibration 总被引：1，自引：0，他引：1
Frederick K. Duennebier George H. Sutton David Harris David A. Byrne 《Marine Geophysical Researches》1984,6(3):311-328
A unique and simple shaker table (shake table or shaking table), designed, constructed, and installed at the Hawaii Institute of Geophysics, has proven to be a valuable aid in testing and calibrating short period seismometers, as well as ocean bottom and ocean sub-bottom seismometer/tilt meter packages. It consists of a platform suspended in a stairwell by a single elastic cord (10 m extended length) driven by GeoSpace HS-10 geophones. Platform motion is monitored by orthogonal reference geophones and tilt meters. The relatively low natural periods of the platform, about 1.9 sec vertical and 6.5 sec horizontal, provide sufficient isolation from local vibrations that calibration can be made near operational amplitudes. Vertical or horizontal driver geophones can be driven by a commercial signal generator or white noise generator, or from magnetic tape output. The table can also be tilted with respect to the drivers to determine tilt tolerances and to calibrate tilt meters. A Hewlett-Packard 3582-A spectrum analyzer, used to analyze both reference and output signals, provides near real-time system cabibration and is an efficient means for investigating parasitic system resonances. The analyzer can also provide a white noise signal source to the driver geophones.Hawaii Institute of Geophysics Contribution 1443. 相似文献
5.
A series of transient tests were conducted to determine the seafloor coupling characteristics of a new ocean-bottom seismometer (OBS) developed for the United States Office of Naval Research (ONR). The OBS comprises a large recording package and a separate sensor package that is deployed from the recording package. In addition to the coupling characteristics of both the sensor and the recording packages, the seismic energy radiated from the main recording package as a result of motion of the recording package was measured. The observed vertical coupling resonances of both the recording package and the sensor package are in good agreement with those predicted by a simple model of soil-structure interaction. The most important result of this study is that significant energy is radiated from the recording package in response to horizontal motions of the recording package. When the sensor package is 1 m from the recording package, the amplitude of the recorded signal is similar to that recorded in the recording package. In the field, this effect will result in distortion of seismic signals and increased background noise recorded by the sensor package if the recording package is disturbed by seafloor currents or biological activity. The amplitude of this signal attenuates by approximately a factor of two as sensor/recorder separation is increased from 1 to 6 m, suggesting that an improved response can be achieved by increasing the separation between the recording package and the sensors. This effect is much less severe for vertical disturbances of the recording package. 相似文献
6.
This paper describes the life testing of a 35-kV power cable that will connect a single anchor leg mooring (SALM) buoy with a platform in several hundred feet of water. While there are many power cable installations to offshore platforms and between platforms, this system is unique because the cable will be constantly flexing in compression as the mooring buoy moves in the water. The buoy design includes an articulated leg with universal joints to which the cable is clamped. It is the loop in the cable where it crosses a universal joint that is flexed, and is a major cause of concern. To predict the effects of this constant flexure while energized, a flex simulator and electrical circuit were devised to duplicate the service environment as closely as possible. This paper describes the cable system, the test apparatus and procedure, and the results obtained. 相似文献
7.
自升式连体潜标测量系统的设计与实施 总被引：1，自引：1，他引：0
针对有缆潜标系统测量质量不稳定,缆绳阻力大、浮球浮力不足,测量系统难以绷紧,导致潜标摇摆、缆绳倾斜,受海洋环境的其他外力作用,影响采集资料的质量等问题,设计了自升式连体潜标测量系统。该系统最大特点是把各种仪器设备与释放器搭载组合到同一平行面的潜标内,把仪器设备、释放器与浮体材料合成为单位体积最小的潜标测量平台。该系统还有体积小、质量轻、造价低、操作简便等特点,适用于水深1 200 m内的海区,采用座底方式进行测量。系统通过释放装置脱钩,脱钩后连体潜标可自行升浮到海面,并具有隐蔽性好不易被破坏的优点。经过近1 a的试验,已多次在南海水深400 m多的海区顺利完成了海上投放与回收试验,试验结果良好。 相似文献
8.
R. A. Stephen D. E. Koelsch H. Berteaux A. Bocconcelli S. Bolmer J. Cretin N. Etourmy A. Fabre R. Goldsborough M. Gould S. Kery J. Laurent G. Omnes K. Peal S. Swift R. Turpening C. Zani 《Marine Geophysical Researches》1994,16(4):243-286
The Seafloor Borehole Array Seismic System (SEABASS) has been developed to measure the pressure and threedimensional particle velocity of the VLF sound field (2–50 Hz) below the seafloor in the deep ocean. The system consists of four three-component borehole seismometers (with an optional hydrophone). a borehole digitizing unit, and a seafloor control and recording package. The system can be deployed using a wireline re-entry capability from a conventional research vessel in Deep Sea Drilling Project (DSDP) and Ocean Drilling Project (ODP) boreholes. Data from below the seafloor are acquired either onboard the research vessel via coaxial tether or remotely on the seafloor in a self-contained package. If necessary the data module from the seafloor package can be released independently and recovered on the surface. This paper describes the engineering specifications of SEABASS, the tests that were carried out, and preliminary results from an actual deep sea deployment. VLF ambient noise levels beneath the seafloor acquired on the Low Frequency Acoustic-Seismic Experiment (LFASE) are within 20 dB of levels from previous seafloor borehole seismic experiments and from land borehole measurements. The ambient noise observed on LFASE decreases by up to 12 dB in the upper 100 m of the seafloor in a sedimentary environment. 相似文献
9.
10.
Duennebier F.K. Harris D.W. Jolly J. Babinec J. Copson D. Stiffel K. 《Oceanic Engineering, IEEE Journal of》2002,27(2):212-217
The Hawaii-2 Observatory seismic system is currently transmitting high-quality seismic data from the ocean floor in the central NE Pacific Ocean through Hawaii to the IRIS Data Management Center. The system includes broad-band seismic, geophone, acoustic, and ocean current sensors. The seismic sensors are buried about 0.4 m below the ocean floor to improve coupling to the ocean bottom and to reduce noise levels. The system can be remotely calibrated, leveled and locked, and gains can be changed on command from shore. Data are temporarily stored in the seismic package for retransmission as needed to correct for transmission problems and to prevent loss of data. Data generated are valuable for studies of the Earth's structure and the dynamics of earthquakes 相似文献
11.
12.
William A. Prothero Jr. 《Marine Geophysical Researches》1977,3(1):119-141
The ocean bottom seismometer capsule contains a 1 Hz. vertical seismometer and triggerable or programmable digital recording system. The output of the seismometer is continuously digitized at a preselected rate of 64, 128, or 256 samples/sec. The digital data words are mixed with a time code and synchronization characters, serialized and passed through a 1536 sample shift register which acts as a delay line. The serial output bits are then encoded and recorded on a SONY TC800B tape recorder which is turned on when a seismic event occurs. The event trigger occurs when the seismic signal jumps to 8 times the time averaged input signal. A memory may be programmed to run the recorder on a schedule so that small amplitude signals from refraction shots are sure to be recorded. Data are recovered using the same recorder for playback and a decoder which provides an analog output for field data interpretation or a digital output for computer analysis. An acoustic transponder allows precise ranges between the capsule and ship to be determined. In addition, commands for the capsule to release or to transmit diagnostic data may be given from the surface ship. The capsule falls freely to the ocean bottom. After a predetermined time or when a release command is received, it is released from a 68 kg steel tripod and floats to the surface. A dual timer and explosive bolt system is used to increase recovery reliability.The first capsules were designed and constructed between October 1972 and October 1973. Good results were obtained from 38 out of 43 launchings made on six expeditions in 1974, 1975, and 1976. Four capsules have been lost. 相似文献
13.
14.
Echert D.C. Morison J.H. White G.B. Geller E.W. 《Oceanic Engineering, IEEE Journal of》1989,14(2):195-202
The development and initial field test results of the Autonomous Ocean Profiler (AOP) are described. The profiler uses a hydrodynamic lift device to fly the instrument package up and down the water column along a taut vertical cable. Because the local currents drive the platform's vertical motion, power requirements are low, and therefore long, unattached deployments are possible. By using ARGOS or GOES satellite retrieval networks, the system can supply near-real-time data. The system provides profile data at very high vertical resolution in contrast to conventional buoys, which gather data only at fixed sensor depths. Because only a single set of sensors is required to cover the vertical range desired, the system is low cost and, for many applications, expendable. The initial deployment configuration is as an Arctic drifting buoy 相似文献
15.
A pop-up bottom seismic recorder designed for seismic refraction experiments was built by the Institute of Oceanographic Sciences in 1968. The device is housed within a 71 cm diameter sphere weighing 270 kg when launched. signals picked up by a hydrophone are recorded in analogue form on magnetic tape in the band 2–100 Hz. The total continuous recording period is 12 hr but the lifetime of the system can be effectively extended by cycling the tape-recorders to allow shooting to go on for up to 3 days. Ballast release is by acoustic command or by pre-set clock. The instruments have been used in water depths from 150 to 4820 m making a total of 63 deployments with a 95% recovery rate. A new version with three-component geophones is being built. 相似文献
16.
基于南海北部浮标和潜标的声学多普勒流速剖面仪（ADCP）数据,通过一套几何算法计算了台风海鸥（1415）期间ADCP的空间变化和流速误差,并进行数据校正。浮标上,台风过后ADCP的水平位移最大可达2.61 km,水平流速误差最大可达0.27 m/s,垂向流速误差最大仅为5×10-4 m/s;温跃层流速校正值在台风过后显著大于流速测值,这表明水平校正对于温跃层流速的质量控制很重要。潜标上,ADCP最大垂向位移增量为179 m,最大绳子倾角为35°,最大水平位移为1.5 km; ADCP水平流速误差和倾角误差都很小,在数据校正中可忽略不计,但对台风过后中层流速的垂向校正不能忽略。 相似文献
17.
A low-cost, expendable, helicopter-deployed, wave-riding buoy is described that has been developed to measure meteorological properties at sea. The buoy weighs 8.2 kg and is 1.3-m long and 8.9 cm in diameter in its stored configuration. After deployment, the buoy extends a 2.5-m sensor mast above the water and a 3.8-m ballasted keel below the water. Buoyancy is provided by an inflated air bladder. An airsonde electronics package that measures relative humidity, barometric pressure, and air temperature transmits the data via a UHF transmitter to a receiver on a helicopter. The received data are displayed and recorded in the helicopter. The buoy is considered simple to construct, uses off-the-shelf hardware, and requires very few, easily machined components 相似文献
18.
对长达70.20m的东海浅钻EY02-1进行了岩石磁学和古地磁分析,证明沉积物的载磁矿物主要为低矫顽力的磁铁矿,磁性地层揭示了发生于9.62~8.58m的磁极性事件,结合钻孔上部的AMS14C测年证明它为全新世初期的哥德堡磁极性漂移,线性外推的时间是距今12681~10206Ma,为全新世开始时地磁场是否发生过短期的磁极性漂移提供了新证据;与东海高分辨率的浅地层地震剖面以及典型钻孔(中法联合东海地震调查和DZQ4钻孔)对比还揭示,在中更新世地层中也出现过两次磁倾角变化。在钻孔中下部54.00~50.94m(2271—2151号样品)出现一段磁倾角变小甚至变成负值,但是由于该段沉积物以粗颗粒的砂为主并且负向样品并不连续,依据研究的标准不作为反磁极性事件。第二个比较连续的负向样品段出现在最底部70.20~64.31m。虽然研究区域内不乏揭示中更新统地层的地震剖面,但至今没有足够长的钻孔在时间上予以佐证。根据东海地震相对比和沉积物中海侵和海退旋回的不同特征以及布容期以来报道的反磁极性事件发生的时间来推测下部地层的时代归属。由于钻孔最底部的沉积主要是粗颗粒的粉砂质砂和细砂,同时钻孔也穿透了倒数第二冰期的杂乱地震相地层和其下的平行透明海相层,所以推测下部的倒转可能为发生在MIS8晚期的CR0反磁极性事件(距今265~255ka)。 相似文献
19.
A numerical method for the dynamic simulation of towed cables is presented. The cable is loaded by fluid drag, tension, gravity and buoyancy, including the effects of weights and floats. The development of a cable can be simulated as well as the separation of a cable under excessive load and the subsequent behavior of the broken parts. The system is constructed from a set of generic elements representing such items as cable or rope strands, knots (reference points on rope sections), kinks (sliding reference points on cable sections that change length), cable ends and winches. A mathematical graph organizes these elements in a general and flexible fashion: it allows construction of complex systems and permits structural redefinition during the simulation. The nodes of the graph coincide with the various reference points of the problem, at which physical parameters are lumped and to which sets of ordinary differential equations are associated that define the motions of the points. The links of the graph describe the physical connections between the nodes. Application of new methods for solving stiff, sparse systems of coupled ordinary differential equations enables efficient simulation of snap-loads and other severe events. Results are presented that compare quantitatively with laboratory measurements. A further example shows the behavior of a breaking cable that is qualitatively reasonable. 相似文献
20.
Narumi Takahashi Yasuhisa Ishihara Hiroshi Ochi Tatsuya Fukuda Jun’ichiro Tahara Yosaku Maeda Motoyuki Kido Yusaku Ohta Katsuhiko Mutoh Gosei Hashimoto Satoshi Kogure Yoshiyuki Kaneda 《Marine Geophysical Researches》2014,35(3):243-253
We have developed a new system for real-time observation of tsunamis and crustal deformation using a seafloor pressure sensor, an array of seafloor transponders and a Precise Point Positioning (PPP ) system on a buoy. The seafloor pressure sensor and the PPP system detect tsunamis, and the pressure sensor and the transponder array measure crustal deformation. The system is designed to be capable of detecting tsunami and vertical crustal deformation of ±8 m with a resolution of less than 5 mm. A noteworthy innovation in our system is its resistance to disturbance by strong ocean currents. Seismogenic zones near Japan lie in areas of strong currents like the Kuroshio, which reaches speeds of approximately 5.5 kt (2.8 m/s) around the Nankai Trough. Our techniques include slack mooring and new acoustic transmission methods using double pulses for sending tsunami data. The slack ratio can be specified for the environment of the deployment location. We can adjust slack ratios, rope lengths, anchor weights and buoy sizes to control the ability of the buoy system to maintain freeboard. The measured pressure data is converted to time difference of a double pulse and this simple method is effective to save battery to transmit data. The time difference of the double pulse has error due to move of the buoy and fluctuation of the seawater environment. We set a wire-end station 1,000 m beneath the buoy to minimize the error. The crustal deformation data is measured by acoustic ranging between the buoy and six transponders on the seafloor. All pressure and crustal deformation data are sent to land station in real-time using iridium communication. 相似文献