共查询到20条相似文献，搜索用时 892 毫秒
1.
Foundations of offshore structures are designed to withstand a combination of static and cyclic loads due to ocean waves. Wave action on offshore structures can cause a significant amount of cyclic horizontal and vertical forces to be transmitted to the soil through the foundation. In all these cases, these cyclic loads are considered to be superimposed over the initial sustained static stress due to the self-weight of structures. This study considers various factors that influence the development of deformation and pore water pressure in a typical cemented marine clay. These results show that the sustained static shear stress significantly influences the strength and deformation behavior of marine clay under cyclic loading. Up to a certain range of sustained static stress, there is an improvement in strength during cyclic loading and the cyclic strains are greatly reduced. 相似文献
2.
Huayang Lei Jingjin Liu Min Liu Zhipeng Zhang Mingjing Jiang 《Marine Georesources & Geotechnology》2017,35(2):281-291
The mechanical behavior of clay subjected to cyclic loading is important to consider in the design of the foundations of many types of structures that must resist cyclic loading, such as subgrades and offshore foundations, because clay undergoes greater settlement under cyclic loading than under static loading. The difference in settlement between these two loading patterns due to creep behavior is affected by the cyclic frequency and the cyclic stress ratio. This study investigated the effects of the frequency and cyclic stress ratio of cyclic loading on the creep behavior of a natural clay in China using stress-controlled triaxial tests. The assessed the following parameters: three frequencies, four cyclic stress ratios, and six vertical stresses. The test results indicate that the soft clay displays accelerated creep behavior under dynamic loads. A specific “limit frequency” (in this case, 0.2 Hz) and a “safe load” at which the strain of the soft clay increases very slowly were observed. The effect of the effective axial stress on the creep behavior increases with the increase in the cyclic stress ratio. Based on the tests, the critical cyclic stress ratio is 0.267 at a certain effective axial stress and frequency. 相似文献
3.
桶形基础越来越广泛应用于海洋油气平台、海上风机、输电塔、防波堤等构筑物,研究其循环承载特性对以上构筑物服役安全性具有重要意义。通过在软黏土中开展单桶循环上拔以及小间距群桶循环上拔和循环下压超重力离心模型试验,发现循环上拔地基破坏模式为整体破坏,裂隙均呈现圆弧形,循环下压呈现渐进式整体破坏模式,下压过程的挤压作用可明显减小桶周泥面高度,导致其承载力降低。模拟双向受荷工况的循环上拔试验在5次加载后荷载弱化系数开始趋于稳定,远早于单向受荷工况;单向和双向受荷工况循环上拔荷载弱化系数残余稳定值分别为0.31和0.32,循环下压荷载弱化系数最小值为0.35,表明不同加载方式竖向循环荷载作用下,此三者大小均可用软黏土地基灵敏度倒数预估。 相似文献
4.
复合加载下桶形基础循环承载性能数值分析 总被引：1，自引：0，他引：1
作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。 相似文献
5.
海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性 总被引：3，自引：0，他引：3
通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。 相似文献
6.
AbstractIn the coastal area, nearshore and offshore structures have been or will be built in marine soft clay deposits that have experienced long-term cyclic loads. Therefore, the mechanical behavior of marine clay after long-term cyclic loading needs to be investigated. In this research, a series of monotonic and cyclic triaxial tests were carried out to investigate the postcyclic mechanical behavior of the marine soft clay. The postcyclic water pore pressure, shear strength and secant stiffness are discussed by comparing the results with the standard monotonic test (without cyclic loading). It is very interesting that the postcyclic behavior of marine soft clay specimen is similar to the behavior of overconsolidated specimen, that is, the specimen shows apparent overconsolidation behavior after long-term cyclic loading. Then relationship between the overconsolidation ratio and the apparent overconsolidation ratio is established on the basis of the theory of equivalent overconsolidation. Finally, a validation formula is proposed which can predict the postcyclic undrained shear strength of marine soft clay. 相似文献
7.
In offshore engineering, pile foundations are commonly constructed in marine deposits to support various structures such as offshore platforms. These piles are subjected to lateral cyclic loading due to wind, wave action, and drag load from ships. In this paper, centrifuge model tests are conducted to investigate the response of the existing single piles due to lateral cyclic loading. The cyclic loading was simulated by a hydraulic actuator. It is found that the residual lateral movement and bending strain are induced in the existing pile after each loading–unloading cycle. This is because plastic deformation is induced in the soil surrounding the existing pile during each loading–unloading cycle. By increasing the applied loads during cyclic loading–unloading process, the lateral movements and bending strains induced in the pile head increase simultaneously. As the cyclic loading varies from 10 to 50 kN, the residual pile head movement increases from 40 to 154?mm, and the residual bending strain of the existing pile varies from 100 to 260 με. The ratio of residual to the maximum pile head movements varies from 0.17 to 0.22, while the ratio of residual to the maximum bending strains is in a range of 0.12–0.55. 相似文献
8.
Undrained strength behaviour of a cemented marine clay under monotonic and cyclic loading 总被引：1，自引：0，他引：1
The paper presents the results of a series of monotonic and cyclic triaxial shear tests carried out to study the influence of the strain effect and load cycles on the undrained shear strength of a cemented marine clay from the East coast of India. The undrained shear strength of Indian coastal marine clay has been established from a detailed shear testing carried out in three phases. Undisturbed soil samples taken out from the seabed were used in the test. In the first part, a comprehensive monotonic shear testing has been carried out under both stress-controlled and strain rate-controlled conditions. In the second phase on identical soil specimen, undrained cyclic shear tests were carried out at various cyclic stress ratios (CSR) and these stress levels are chosen in such a way so that no failure occurred during testing. In the final phase post cyclic monotonic shear testing was conducted to qualitatively evaluate the damage caused by cyclic loading. The monotonic shear test results bring out the influence of cementation that can be detected by the stress-controlled test. The cyclic stress results are analysed in terms of CSR. Further, the results are correlated in terms of stress path. 相似文献
9.
Estimation of Undrained Bearing Capacity for Offshore Soft Foundations with Cyclic Load 总被引：3，自引：0，他引：3
The degradation strength of soils under cyclic loading is studied and a method for deter-mining the cyclic degradation strength with cyclic triaxial tests is given in the paper.Furthermore,a dum-my static method for estimating the undrained bearing capacity for offshore soft foundation under waveloads is developed.It can consider the effect of the difference of cyclic stress for different parts of the foun-dation on both the degradation strength of the foundation soil and the bearing capacity so that the esti-mated result can better reflect the real condition of foundation under cyclic loading.The method can be ap-plied to plane and space problem. 相似文献
10.
In the field of ocean engineering, pile foundations are extensively used in supporting several structures. In many cases, piles are subjected to significant lateral loads. The environment prevalent in the ocean necessitates the piles to be designed for cyclic wave loading. In this investigation, the behaviour of rigid piles under cyclic lateral loading has been studied through an experimental programme carried out on model piles embedded in a soft marine clay. Static tests were also conducted on piles embedded in a clay bed prepared at different consistencies suitable to field situations. Cyclic load was applied by using a specially designed pneumatic controlled loading system. Tests were conducted on model piles made of mild steel (MS), aluminium and PVC with wide variation in pile soil relative stiffness. For cyclic load levels less than 50% of static lateral capacity, the deflections are observed to increase with number of cycles and cyclic load level and stabilise after a certain number of cycles. For cyclic load levels greater than 50% of static lateral capacity, the deflections are observed to increase enormously with number of cycles. The results of post-cyclic load tests indicate that the behaviour under static load can improve for cyclic load levels less than 40% of the static lateral capacity. The variations in the load capacity due to cyclic loading are explained in terms of the changes in strength behaviour of soil. 相似文献
11.
AbstractUnder seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress. 相似文献
12.
Abstract In the field of ocean engineering, anchors are used for several purposes. This article studies the behavior of a helical anchor embedded in soft marine clay under vertical repetitive loading. Helical anchors are simple steel shafts to which one or more helical plates are attached at regular intervals. The tests are conducted on a model helical anchor installed in a soft marine clay bed prepared in a test tank. Repetitive loading is applied using a pneumatic loading arrangement. Different cyclic load ratios and time periods are adopted. In each test, after the application of repetitive loading, poststatic‐pullout tests are conducted to observe the effect of repetitive loading on anchor behavior. From the test results, it is found that, up to a cyclic load ratio of 55%, there is no reduction in capacity. Instead, there seems to be a marginal increase in capacity and reduction in displacement. The reasons for this behavior are explained in terms of induced changes in strength and deformation behavior of marine clay under repetitive load. However, at higher cyclic load ratios, there seems to be reduction in pullout capacity of the anchor, and the reason for this is explained in terms of strain criteria. From this investigation, it can be concluded that the deep anchor is more suitable to a marine environment than a shallow anchor. 相似文献
13.
AbstractCement soil mixing piles are an effective treatment method for marine soft clay. To investigate the static and dynamic characteristics of the composite soil with cemented soil core, a series of experiments are carried out by using the cyclic simple shear test. The result shows that, the static shear strain showed strain hardening, cemented soil core can improve static shear strength of composite soil, vertical stress can enlarge reinforcement of cemented soil core. The tendency of strain development of composite soil with different area replacement ratios under cyclic loading is the same as that of pure clay, existing critical cyclic stress ratios corresponding to different area replacement ratios. In addition, improving area replacement ratio can increase cyclic strength. At same time, adding of cemented soil core does not change shape of hysteresis curve compared with it for clay either. Moreover, cemented soil core can also obstruct stiffness softening. Through regression analysis of the experimental data, relationship between cyclic number and soil softening index is proved to be linear. The results can give a reference for the dynamic characters of the marine soft clay foundation with cement soil mixing piles. 相似文献
14.
风机基础作为海上风机整体结构的重要组成部分,承受着上部风机所受到的风浪流荷载,并且对风机的安全性及可靠性至关重要。吸力式桶形基础由于其安装简单和可重复利用等优点,在海洋平台基础中得到了广泛应用,并逐步应用于海上风机基础中。但由于海上风机与海洋平台在海洋环境中的荷载工况有一定的差别,仍需要通过对其承载特性研究现状进行全面认识,以实现吸力式桶形基础在海上风机基础中的可靠应用。文中通过总结和评价现有研究对桶形基础在不同土体条件以及荷载条件下进行试验及数值模拟分析得到的研究结果,综述了静荷载和循环荷载作用下砂土和黏土中的吸力式桶形基础的承载特性研究现状,以及海上风机吸力式桶形基础的相关研究。文章展望了目前应用于海上风机基础的桶形基础仍缺乏的研究,为海上风机吸力式桶形基础的可靠应用及后续研究提供重要参考。 相似文献
15.
吸力基础具有施工速度快、安装过程中受海况天气影响小且易于回收重复利用等优点,被广泛应用于海洋工程。当吸力基础作为海上风电塔架的基础时,常常承受较大的水平荷载,因此其水平承载力是设计的主控因素。介绍了海上风机基础的设计要求,分析了影响基础水平承载性状的因素,总结了吸力基础受水平单调荷载、水平循环荷载和不同荷载组合三个方面的研究现状。讨论了水平荷载的大小、水平加载的高度(偏心率)、循环荷载的频率、循环荷载的次数、循环荷载的幅值、循环荷载的方向性、竖向荷载对吸力基础水平承载性状的影响,考虑了水平荷载的非共线性,指出了目前研究的不足,明确了吸力基础水平承载性状进一步研究的方向,提出了供工程实践参考的建议。 相似文献
16.
Cumulative Deformation of Soft Clay Under Cyclic Loading 总被引：2，自引：1，他引：2
Yan Shuwang Yan Chi Zhang Jianguo Professor Tianjin University Tianjin Lecturer Tianjin University Tianjin 《中国海洋工程》1993,(3)
Reconstituted specimens are prepared by means of vacuum preloading. Both static and cyclic triaxial tests are carried out, with the specimens consolidated under different principal stress ratios. A finite element method is put forward for calculating the cumulative deformation of soft clay under cyclic loading. 相似文献
17.
Coastal protection is proposed to be made out of a contiguous caisson type of wall. These caissons can be designed to resist both lateral static and cyclic loading. With adequate depth of embedment, the walls can be designed to offer significant lateral passive resistance to counteract the lateral static and cyclic loading arising out of wave action. This article describes a set of laboratory tests on model caissons embedded into soft marine clay with different embedment depths. Specially designed earth pressure cells are embedded into the caisson at different depths. A pneumatic system was used to apply lateral static and cyclic loading. Test beds were prepared conforming to soft clay conditions in a test tank of appropriate size. The test results reveal that with this type of arrangement the variation in earth pressure with depth can be conveniently established. The earth pressure developed is related to the lateral load applied. The depth at which the maximum earth pressure occurs is same for both static and cyclic loading. Further, under cyclic loading there is no failure encountered even under cyclic loading level corresponding to 0.9 times the ultimate static lateral capacity. 相似文献
18.
The influence of cyclic loading on the strength and deformation behavior of cemented marine clay has been studied. This marine clay is of recent Pleistocene origin and deposited in a shallow water marine environment. Open pits were dug in sheeted enclosures and from these pits, undisturbed samples were taken for strength testing. A series of standard triaxial shear tests and stress controlled one-way cyclic load tests were conducted at consolidation stress ranges below and above the preconsolidation pressure. For the stress levels below the preconsolidation pressure, the cyclic loading has brought about the collapse of the cementation bond through an increase in strains, and at higher pressure ranges, the soil behaves like typical soft clay. This experiment studied the rate of development of strain and pore water pressure and shows that rate is a function of number of cycles, applied stress, and stress history. In addition, soil degradation during cyclic loading is studied in terms of Degradation Index. Attempt has been made to predict stain, pore water pressure, and degradation index through an empirical model. 相似文献
19.
A series of centrifuge tests were performed to investigate the response of a free-head monopile due to cyclic lateral loading in normally consolidated clay. By linking the maximum reaction-force point of the final cycles in all tests with various amplitudes, a postcyclic reaction-force curve is obtained, which can be used to assess the postcyclic remolded lateral stiffness. To numerically analyze the tests, a strength degradation model of the clay is calibrated by the T-bar cyclic test. However, this model is T-bar-dependent, which is unable to capture the degrading behavior of the monopile stiffness. Thus, a modification approach is proposed based on the upper bound theory, and the modified model is further combined with finite element analysis to simulate the cyclic behavior of the model pile. The simulation results show similar degrading trend and consistent postcyclic remolded lateral stiffness with the model tests. This further demonstrates that the remolded lateral stiffness mainly depends on the soil remolded strength, which is one of the parameters calibrated by the T-bar tests. Based on this finding, a simplified numerical analysis is proposed, which can predict the postcyclic reaction-force curve by performing one monotonic loading instead of modeling the whole process of cyclic loading. 相似文献
20.
Abstract The strength of saturated clays subjected to low‐frequency cyclic loading is of considerable importance in the design of offshore structures. A series of postcyclic undrained triaxial strength tests were carried out on samples of a silty clay (Keuper Marl), which had not failed under cyclic loading, to investigate the effect of this loading on the postcyclic monotonie effective stress path and strength of the soil. Undrained cyclic loading of normally consolidated and lightly overconsolidated samples by generating positive pore pressures caused the apparent degree of overconsolidation to increase. Samples subsequently subjected to monotonie testing followed effective stress paths commensurate with this apparent overconsolidation and failed on the “Hvorslev” surface on the “dry” side of the stable state boundary surface rather than on the critical state as would be expected of samples of this initial stress history. Samples which were initially heavily overconsolidated did not generate large pore pressures under cyclic loading and did not therefore exhibit large changes in postcyclic monotonie strength. The reduction in strength after cyclic loading therefore is greater for normally consolidated and lightly overconsolidated samples. The pore pressures generated under postcyclic monotonie loading are related to the degree of apparent overconsolidation achieved during cyclic loading. 相似文献