共查询到17条相似文献，搜索用时 156 毫秒
1.
风机基础作为海上风机整体结构的重要部分，承受着上部风机所受到的风浪流荷载，并且对风机的安全性及可靠性至关重要。吸力式桶形基础由于其安装简单和可重复利用等优点，在海洋平台基础中得到了广泛应用，并逐步被应用于海上风机基础中。但由于海上风机与海洋平台在海洋环境中的荷载工况有一定的差别，仍需要通过对其承载特性研究现状进行全面认识，以实现吸力式桶形基础在海上风机基础中的可靠应用。本文通过总结和评价现有研究对桶形基础在不同土体条件以及荷载条件下进行试验及数值模拟分析得到的研究结果，综述了静荷载和循环荷载作用下砂土和黏土中的吸力式桶形基础的承载特性研究现状，以及海上风机吸力式桶形基础的相关研究。文章展望了目前应用于海上风机基础的桶形基础仍缺乏的研究，为海上风机吸力式桶形基础的可靠应用及后续研究提供重要参考。 相似文献
2.
海洋平台吸力式基础的土工离心模拟研究与分析 总被引：11，自引：0，他引：11
综述了国内外已开展的海洋平台吸力式基础的离心模型试验研究,重点讨论了应用离心机模拟吸力式基础承载特性的研究现状。 相似文献
3.
4.
传统吸力基础是一个单桶结构,被广泛作为海洋平台、漂浮结构的基础,近年来也被推广到海上风电塔架。作为风电塔架基础,要充分提高其水平承载能力。为此,提出一种改进的基础形式—裙式吸力基础。采用Z_SOIL有限元软件,针对砂土地基,从水平单调加载和循环加载两个方面,对传统单桶吸力基础和裙式吸力基础进行了承载性能对比研究,得到了相应的荷载-位移曲线。研究结果表明,裙式吸力基础由于设置了"裙"结构,显著提高了其抵抗水平静载和循环水平动力荷载的能力,并能有效控制基础的水平位移,是值得推广应用的一种新型海洋工程基础形式。 相似文献
5.
复合加载下桶形基础循环承载性能数值分析 总被引：1，自引：0，他引：1
作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。 相似文献
6.
吸力基础具有施工速度快、安装过程中受海况天气影响小且易于回收重复利用等优点,被广泛应用于海洋工程。当吸力基础作为海上风电塔架的基础时,常常承受较大的水平荷载,因此其水平承载力是设计的主控因素。介绍了海上风机基础的设计要求,分析了影响基础水平承载性状的因素,总结了吸力基础受水平单调荷载、水平循环荷载和不同荷载组合三个方面的研究现状。讨论了水平荷载的大小、水平加载的高度(偏心率)、循环荷载的频率、循环荷载的次数、循环荷载的幅值、循环荷载的方向性、竖向荷载对吸力基础水平承载性状的影响,考虑了水平荷载的非共线性,指出了目前研究的不足,明确了吸力基础水平承载性状进一步研究的方向,提出了供工程实践参考的建议。 相似文献
7.
桶形基础越来越广泛应用于海洋油气平台、海上风机、输电塔、防波堤等构筑物,研究其循环承载特性对以上构筑物服役安全性具有重要意义。通过在软黏土中开展单桶循环上拔以及小间距群桶循环上拔和循环下压超重力离心模型试验,发现循环上拔地基破坏模式为整体破坏,裂隙均呈现圆弧形,循环下压呈现渐进式整体破坏模式,下压过程的挤压作用可明显减小桶周泥面高度,导致其承载力降低。模拟双向受荷工况的循环上拔试验在5次加载后荷载弱化系数开始趋于稳定,远早于单向受荷工况;单向和双向受荷工况循环上拔荷载弱化系数残余稳定值分别为0.31和0.32,循环下压荷载弱化系数最小值为0.35,表明不同加载方式竖向循环荷载作用下,此三者大小均可用软黏土地基灵敏度倒数预估。 相似文献
8.
为了得到桶基础承受风、浪动荷载的承载性能,结合我国东海地质条件,统计中国东海2010—2020年浅、深海风速和最大海浪数据,通过计算得到风浪荷载并制成ABAQUS软件幅值曲线施加到海上风电吸力桶基础上,分析了吸力桶基础在动荷载作用下的承载特性。结果表明：吸力桶基础受风、浪荷载影响明显,桶基础迎力面受到风浪动荷载产生拉拔现象。在浅海区,桶基础在风浪荷载作用下桶身自上而下变形不协调,风浪荷载最大的10月份桶基础迎力面最大位移超出了规范0.02D的限制,基础失稳;桶基础背力面受压变形较小。在深海区,桶基础在风浪荷载作用下桶身自上而下变形相对协调,施加风浪荷载后桶体迎力面最大位移为14.9 mm,整体上迎力面位移比背力面位移大4 mm,桶体处于稳定状态。相较浅海区的吸力桶单桶结构,深海区吸力桶结构由于尺寸增加,桶体的稳定性得到提高,说明吸力桶结构的尺寸对稳定性起决定性作用。 相似文献
9.
复合加载条件下吸力式沉箱基础承载特性数值分析 总被引：2，自引：0，他引：2
吸力式沉箱基础的承载特性是海洋工程结构设施建造与设计中的一个关键问题。这种新型的深水海洋基础型式,通常承受竖向上拔荷载与水平荷载的共同作用,其工作性能与设计理论远远不能满足工程实践的需要。本文采用有限元分析方法对吸力式沉箱基础的极限承载特性进行数值计算。以大型通用有限元分析软件ABAQUS为平台,通过二次开发,数值实现了Swipe试验加载方法和固定位移比分析方法,针对不同的沉箱长径比、土的强度折减系数,探讨了沉箱基础在垂直上拔荷载和水平荷载单调联合作用下的极限承载力,通过对不同荷载组合的数值计算构造了复合加载条件下沉箱基础破坏包络面。 相似文献
10.
吸力基础是海洋工程中新型的一种基础型式,广泛应用于海洋平台、海洋浮动式结构等,近年来,也被作为浅海离岸风力发电工程的基础。吸力基础易遭受较大的水平动力荷载和弯矩,从而可能产生较大水平位移和转角;同时,由于海床冲刷,会降低其承载能力。为克服这些不足,提出了一种新型吸力基础———裙式吸力基础,把分析传统吸力基础砂土中的沉贯方法,拓广到裙式吸力基础中,研究该基础型式在砂土中的可沉贯性以及所需的吸力;并与同情况下的传统吸力基础进行了比较,证明了所提出的裙式吸力基础具有较好的沉贯性能,具有工程实践推广价值。 相似文献
11.
Existing tripod suction bucket foundations, utilised for offshore wind turbines, are required to resist significant lateral loads and overturning moments generated by wind and currents. This paper presents an innovative type of tripod bucket foundation, ‘hybrid tripod bucket foundation’, for foundations of offshore wind turbines, which has the ability to provide a larger overturning capacity compared with conventional tripod buckets. The proposed foundation consists of a conventional tripod bucket combined with three large circular mats attached to each bucket. A series of experiments were conducted on small-scale models of the proposed foundation subjected to overturning moment under 1g conditions in loose sand. Different circular mat diameter sizes with various bucket spacings were considered and the results were compared with conventional tripod bucket foundation. Finite element models of the proposed foundation were developed and validated using experimental results and were used to conduct a parametric study to understand the behaviour of the hybrid tripod bucket foundation. The results showed that there is a significant increase in overturning capacity provided by the novel foundation. The results of this work can significantly improve lowering the costs associated with installation of foundations to support offshore wind turbines. 相似文献
12.
A shallow suction bucket is a new foundation type for offshore wind turbines. Due to its large size and bulky shape, the bucket and the soil within the bucket do not necessarily deform as a whole. Moreover, limited research has been conducted on the hydrodynamic wave influence on the shallow bucket bearing response. These factors pose great challenges to the shallow bucket foundation design. This paper presents a set of centrifuge tests of a shallow bucket model subjected to monotonic and dynamic lateral loads to study the lateral bearing response of shallow bucket foundations in the field under combined loads induced by wind, waves, etc. In addition to the routine measurements (e.g., load-displacement), the soil pressures on the bucket and the distribution and evolution of the excess pore pressures in the surrounding soils are also obtained. The deformation pattern of the bucket (e.g., rotation center) is revealed through displacement measurements. Finally, the proposed easy-to-use analytical equations using the limit equilibrium to assess the bearing capacity of bucket foundations, taking into account the influence of the soil strength degradation caused by hydrodynamic wave loadings, are found to yield good results upon comparison with the centrifuge data, providing useful guidelines for the design of shallow bucket foundations. 相似文献
13.
Suction caissons are considered as an alternative foundation solution for offshore wind turbines. In the present study, three-dimensional finite element (FE) analyses are performed to assess the behavior of a bucket foundation and soil supporting the bucket under cyclic and monotonic loading conditions. A parametric study is also performed for a wide range of bucket geometries and two different soil densities. The results indicate that bucket geometry and soil properties significantly affect the foundation response due to cyclic loading conditions. The bucket with the smallest geometry installed in medium dense soil exhibits the lowest stiffness in initial loading and then with the progress of cyclic loads experiences lower stiffness compared to the caissons with larger geometries. The sensitivity of the foundation response to the soil density is higher than its geometry. The bucket under the lowest vertical load experiences the lowest stiffness in both virgin loading and during the progress of cyclic loads. The highest soil displacement is observed near the lid at the interior of the bucket. Stresses caused by cyclic loading belong to certain ranges. Additionally, increases in the skirt length result in increases in the stress ranges and shift the range to the right side. With respect to the monotonic loading conditions, normalized diagrams are proposed that can be used for the preliminary design of suction bucket foundations. 相似文献
14.
This paper presents the results of three-dimensional finite element analyses of the suction bucket foundation used for offshore wind turbines. The behavior of the bucket and the response of soil supporting the bucket in dense and medium dense sandy soils subjected to static horizontal load are investigated. Field tests results and a centrifuge model test are used to validate the numerical model. Dimensionless horizontal load-displacement and overturning moment-rotation relationships are derived utilizing the Power law and Buckingham’s theorem. The results show good agreement between the numerical analysis results and the straight lines obtained from the Power law until a specific value of horizontal load and overturning moment. Regarding stress behavior of soil supporting the bucket, due to soil densification and bucket movement, maximum stresses are seen near the bucket tip at the right inside of the bucket. The major part of the applied load is transferred by the bucket skirt. Numerical analysis modeling results show that the bucket rotation and displacement are highly dependent on the bucket geometry and soil properties in addition to loading conditions. Normalized equations and figures for the ultimate horizontal load and overturning-moment capacities are presented and can be used for the preliminary design of the bucket foundations in sandy soils. 相似文献
15.
针对海上风电负压桶型基础,以提高桶基水平承载性能和降低结构动力响应为目的,提出了一种加装稳定翼的负压桶型基础型式。通过在桶身设置一组稳定翼,使得桶周土抗力得以充分利用。以单立柱负压桶基为例,建立桶土全实体有限元模型,进行了静力分析和包括模态分析、瞬态分析、谱分析在内的动力分析。结果表明:稳定翼的设置增强了桶基水平承载性能;水平位移和动力响应显著减小;结构低阶固有频率略有提高。 相似文献
16.
17.
海上支撑结构的优化设计是海上风机技术发展的必然趋势,降低支撑结构的载荷是保证风机安全运行的有效途径。海上支撑结构受到风浪复杂环境荷载作用,风、浪载荷决定着塔底承受较大的剪力和倾覆力矩,同时风浪的随机性和周期性会影响塔架的疲劳载荷。基于海上风机支撑结构频率对载荷影响的研究,分析海上支撑结构频率对叶片根部挥舞和摆振响应的影响,探究频率对风机响应的影响机理。研究表明：波浪频率诱导是基础疲劳载荷响应的主要原因;开展单桩基础设计,当整机频率确定时,基础变径段可设置于浪溅区下部区域范围;叶片摆振响应受1P频率影响较大,在风机设计时可增加叶片摆振方向的阻尼;当整机频率邻近3P频率时,塔筒刚度变化对基础载荷响应的影响大于基础刚度变化;海上支撑结构设计时可优先考虑塔筒刚度。 相似文献