共查询到20条相似文献，搜索用时 156 毫秒
1.
2.
为弥补测高数据在近海区域因为编辑准则被剔除而导致近海测量数据质量不高的缺点,利用5参数模型的两种形式和Ice-2模型对Jason-2卫星在中国南海部分海域的海洋回波波形进行了波形重跟踪的研究,并选择20个海洋回波波形,依据最小二乘原理进行计算、分析、对比,发现5参数模型的指数形式的结果和Ice-2模型结果非常接近。研究结果表明,在开阔的海域,对Jason-2波形进行3种方法波形重跟踪时,可以优先考虑Ice-2模型。波形重跟踪技术能够提高卫星测高数据利用率,为科学研究提供可靠的数据保障。 相似文献
3.
4.
高度卫星定轨精度对其测高精度数据在海洋应用中的影响 总被引：2，自引：0，他引：2
卫星测高术是７０年代发展起来的一项新技术，到目前为止国外已陆续发射了七颗载有高度计的卫星，高度计卫星定轨的精度对测高数据的应用有很大影响，本文概述了卫星高度计测高数据在海洋应用上的一些结果、影响轨道的因素、测轨方法和轨道精校正方法，最后根据现有卫星轨道校正数据得到卫星轨道误差与校正精度的关系式，据此分析了轨道计算误差地卫星高度计测高数据在海洋应用中的影响。 相似文献
5.
6.
本文从卫星测高数据处理中网距的选取、数据点的图形结构、网格算子等三个方面加以讨论,提出了频域中数据网格化的方法,最后利用两个周期的Topex/Poseidon卫星测高数据进行计算分析,得出了一些卫星测高数据网格化的经验。 相似文献
7.
8.
联合HY-2A、Geosat、ERS1/2、Envisat、T/P、Jason1/2等多颗测高卫星,通过共线处理和交叉点平差削弱海面时变效应和径向轨道误差等影响,以Jason-1测高卫星作为参考,对多代测高卫星进行基准统一,消除测高数据的不一致性,基于全球EGM2008重力场模型,采用移去恢复技术和逆Vening-Meinesz公式反演中国南海(0°~23°N,103°~120°E)2'×2'重力异常,与船测重力数据比较,均方根误差为4.9m Gal。 相似文献
9.
探讨了卫星测高数据处理的共线秩亏平差算法，推求了消除秩亏的附加条件系数矩阵。用Topex测高数据对轨道误差模型进行了验证。 相似文献
10.
为研究满足HY-2B星载GPS定轨要求的EGM2008重力场模型合理阶次和HY-2B卫星简化动力学定轨精度,采用HY-2B卫星14天星载GPS观测数据及不同阶次EGM2008重力场,进行简化动力学轨道确定。结果表明：采用120阶及以上阶次的EGM2008重力场模型,能够获得厘米级高精度定轨结果。同时,检核结果显示：采用简化动力学法定轨时,载波相位残差结果稳定在6.2～6.8 mm之间,重叠轨道对比结果在轨道径向、切向、法向上均优于0.6 cm, SLR检核整体轨道精度优于4 cm。定轨结果满足测高卫星需求,可为后续我国海洋系列卫星精密轨道确定等相关科学研究提供借鉴。 相似文献
11.
Chung-Yen Kuo Huan-Chin Kao Hyongki Lee Kai-Chien Cheng Li-Ching Lin 《Marine Geodesy》2013,36(2):188-197
This study focuses on assessing the accuracy of 20-Hz waveform retracked Jason-2 (J-2) altimetry sea surface heights (SSHs) in the vicinity of Taiwan by comparisons with the TOPEX/Poseidon (T/P) 10-Hz SSHs and sea level data from the Anping tide gauge. The study areas exhibit high, medium, and low amplitudes of ocean tides and contain diverse bathymetries with depths of 0–4000 m. The performance of Offset Center of Gravity (OCOG), threshold, modified threshold, and ice retrackers was examined by comparing the retracked SSHs with Earth Gravitational Model 2008 (EGM08) geoid via the use of the improvement percentages (IMPs). The results indicate that both altimetry measurements are significantly improved by waveform retracking techniques, with a maximum IMP of 46.6% for T/P and 82.0% for J-2, and the optimal achievement of retrackers is influenced by the characteristics of the study areas. In addition, valid retracked J-2 SSHs are much closer to shorelines than T/P. A comparison of retracked J-2 data with Anping tide gauge records reveals that applying the optimal retracking algorithms reduces the root mean squares of differences and increases the number of valid measurements. 相似文献
12.
Surajit Ghosh Praveen Kumar Thakur Vaibhav Garg Subrata Nandy Shivprasad Aggarwal 《Marine Geodesy》2015,38(3):597-613
In the present study, behavior of the SARAL/AltiKa (Satellite with ARgos and ALtiKa) waveforms over Maithon Reservoir (～65 km2 of surface area), Jharkhand, India, has been studied. The estimated water level has been compared with the in situ measurements at hydro-gauging station at the dam site. The problem of minimization of errors in the water level retrieval from AltiKa measurements has been resolved by improvement of the retracking method. A real retracking gate detection algorithm based on statistical analysis harnessing various physical parameters of the waveform has been developed, which has been applied to SARAL/AltiKa waveforms over the Maithon reservoir. Comparing the in-situ measurements with altimetry data (from cycle 1, 19 March 2013 to cycle 12, 8 April 2014) showed that it is crucial to improve the retracking method. Results showed accuracy of water level monitoring increased by nearly 76% by the newly developed waveform retracking algorithm over non-retracked water level. We also compared this new method with the existing ice-1 algorithm and found that with the new method there is improvement of ～27% over ice-1 retracked water level. The correlation coefficient values and root mean square values without retracking, with ice-1 algorithm and with newly developed retracking algorithm were 0.87, 0.91, and 0.95, and 8.12 cm, 2.08 cm, and 1.42 cm, respectively. This shows the proposed retracker performed better than ice-1. The retracking procedure helped in outliers' identification and substitution and with waveform fitting and waveform parameter extraction. This algorithm should have good performance capability for retrieving water level over inland water bodies like Maithon reservoir. 相似文献
13.
14.
Fukai Peng 《Marine Geodesy》2018,41(2):99-125
A new Brown-Peaky (BP) retracker has been developed for peaky waveforms that usually appear within ～10 km to the coastline. The main feature of the BP is that it fits peaky waveforms using the Brown model without introducing a peak function. The retracking strategy first detects the peak location and width of a waveform using an adaptive peak detection method, and then estimates retracking parameters using a weighted least squares (WLS) estimator. The WLS assigns a downsized weight to corrupted waveform gates, but an equal weight to other normal waveform gates. The BP retracker has been applied to 4-year Jason-1 waveform (2002–2006) in two Australian coastal zones. The results retracked by BP, MLE4 and ALES retrackers have been validated against tide-gauge observations located at Burnie, Lorne and Broome. The comparison results show that three retrackers have similar performance over open oceans with the correlation coefficient (～0.7) and RMSE (～13 cm) between altimetric and tide-gauge sea levels for distance >7 km offshore. The main improvement of BP retracker occurs for distance ≤7 km to the coastline, where validation results indicate that data retracked by BP are more accurate (15–21 cm) than those by ALES (16–24 cm) and MLE4 (19–37 cm). 相似文献
15.
Huan-Chin Kao Kuo-Hsin Tseng C.K. Shum Tzu-Pang Tseng Yuan-Yuan Jia 《Marine Geodesy》2019,42(4):327-343
Satellite altimetry has been proven as an effective technology to accurately measure water level, ice elevation, and flat land surface changes since the 1990s. To overcome limitations of pulse-limited altimetry, new altimetric missions such as Cryosat-2 and Satellite with ARgos and AltiKa (SARAL/AltiKa), have been designed to have higher along-track spatial resolution to measure more accurately inland water levels for small water bodies, and coastal sea level changes. In this study, we evaluate the performance of Cryosat-2 low-resolution (LRM) and SARin modes and SARAL/AltiKa Ka-band data on two connected lakes in central Tibetan Plateau, and in the coastal region of Taiwan. Results are compared with in situ tide gauge data in Taiwan and altimetric lake level time series from the CNES Hydroweb database. Our results show that water level change trends observed by Cryosat-2 20-Hz retracked observations, the SARAL/AltiKa 40-Hz Ice-1 retracked data, and the Hydroweb measurements are consistent with the estimated water level trend of ～0.30?m/y, during 2011–2017, and 2013–2015, for the Tibetan Migriggyangzham Co and Dorsoidong Co, respectively. For the coastal region, the performance of SARAL/AltiKa is better than that of Cryosat-2 LRM data in Taiwan. This finding demonstrates the superiority of the Ka-band over Ku-band radar altimetry. 相似文献
16.
Water Level Retrieval Using SARAL/AltiKa Observations in the Braided Brahmaputra River,Eastern India
Amit Kumar Dubey Praveen Gupta Subashisa Dutta Raghvendra Pratap Singh 《Marine Geodesy》2015,38(3):549-567
In this study, water level retrieval over the Brahmaputra river was done using different retracking algorithms for the 40 Hz waveform data of SARAL/AltiKa satellite. Water level was retrieved at 10 different locations of the river to evaluate the performance and accuracy of Ka band altimeter over the braided river system. Different retracking algorithms such as ice-1, ice-2, threshold, and beta parameter were used to retrieve water levels. A correlation and error analysis between the in-situ and satellite altimetry derived river levels was carried out for all the stations. Performance and accuracy analysis has established that water level can be retrieved with less than 40 cm root mean square error (RMSE) for most of the braided reaches of the river. The statistical analysis have found that Beta parameter algorithm has performed best in most of the cases amongst the different retracking algorithms used in this study. The water levels derived from 10 different locations were used to generate water surface elevation profiles for the monsoon and nonmonsoon periods. The water levels and the water surface profiles derived from satellite altimetry indicate the potential use of altimeters for the parameterization and calibration of river hydrological, hydrodynamic and sediment transport models. 相似文献
17.
O. Z. Zanif P. Vincent L. Amarouche J. P. Dumont P. Thibaut S. Labroue 《Marine Geodesy》2003,26(3):201-238
TOPEX/Poseidon is a well known success, with the operational altimeter (TOPEX) and the experimental one (Poseidon-1), providing data of unprecedented quality. However, there are two major differences between the TOPEX and Poseidon-1 radar altimeters on board TOPEX/Poseidon. The first is related to the estimated range noise; the second is linked to the sea-state bias (SSB) model estimates. Since the recent launch of the Jason-1 radar altimeter (also called Poseidon-2), we have been cross-comparing these three systems to better characterize each of them. Analyzing standard user products, we have found that Jason-1 is behaving like Poseidon-1 and thus shows the same observed differences when compared with TOPEX. A comparative analysis of their features was performed, starting from the on-board acquisition of the ocean return and ending with the ground generation of the high level accuracy oceanographic product. The results lead us to believe that the sources for these differences lie in both the waveform tracking processing and the presence or abscence of a retracking procedure whether on-board or on ground. Because Poseidon-1 and Jason-1 waveforms are retracked while TOPEX waveforms are not in the products distributed to the users, we have applied the same ground retracking algorithm to the waveforms of the three radar altimeters to get consistent data sets. The analysis of the outputs has shown that: (a) the noise level for the three radar altimeters is definitively the same, and (b) the source of the relative SSB between Jason-1 and TOPEX lies in the different behavior of the on-board tracking softwares. 相似文献
18.
《Marine Geodesy》2013,36(3-4):201-238
TOPEX/Poseidon is a well known success, with the operational altimeter (TOPEX) and the experimental one (Poseidon-1), providing data of unprecedented quality. However, there are two major differences between the TOPEX and Poseidon-1 radar altimeters on board TOPEX/Poseidon. The first is related to the estimated range noise; the second is linked to the sea-state bias (SSB) model estimates. Since the recent launch of the Jason-1 radar altimeter (also called Poseidon-2), we have been cross-comparing these three systems to better characterize each of them. Analyzing standard user products, we have found that Jason-1 is behaving like Poseidon-1 and thus shows the same observed differences when compared with TOPEX. A comparative analysis of their features was performed, starting from the on-board acquisition of the ocean return and ending with the ground generation of the high level accuracy oceanographic product. The results lead us to believe that the sources for these differences lie in both the waveform tracking processing and the presence or abscence of a retracking procedure whether on-board or on ground. Because Poseidon-1 and Jason-1 waveforms are retracked while TOPEX waveforms are not in the products distributed to the users, we have applied the same ground retracking algorithm to the waveforms of the three radar altimeters to get consistent data sets. The analysis of the outputs has shown that: (a) the noise level for the three radar altimeters is definitively the same, and (b) the source of the relative SSB between Jason-1 and TOPEX lies in the different behavior of the on-board tracking softwares. 相似文献
19.
Retracking altimeter waveforms over inland water bodies is a challenging task as a wide range of waveform is encountered while the retracking algorithms are available only for a handful of echo shapes. One such waveform shape widely encountered in lakes and reservoirs is the multipeak echo. These echoes are produced when the interacting surface in the altimeter footprint is not homogeneous and a number of different types of surfaces contribute to the resulting waveform. The widely used conventional retrackers, namely the Brown, Beta-5, Ice-2, OCOG, and threshold, can retrack a number of different waveform shapes such as the Brown like waveforms, specular waveforms, and rectangular waveforms but may not perform well for multipeak waveforms. In this article, a technique has been demonstrated to identify the different subwaveforms within a multipeak waveform and identify the subwaveform corresponding to the target at nadir. The subwaveform that is reflected from the nadir surface is identified from apriory information about the surface topography of the area. The subwaveform is then retracked using the 50% threshold to find the correct retracked range and water height. This technique has been tested for nine cycles of SARAL SIGDR data on Ukai reservoir, Gujarat, India, and found to perform much better than the other retrackers, particularly for multipeak waveforms. 相似文献
20.
本文基于Amarouche的二阶理论回波模型,导出了带有偏度系数的二阶理论回波模型;针对HY-2A卫星高度计波形特点,引入了奇异值分解滤波,并根据最大似然估计算法反演参数的不同得到6种重跟踪方案;利用其中的五参数方案处理该波形数据,获得海面散射点高度概率密度函数中偏度的合理取值为0.15;将结果分别与浮标、Jason-1和HY-2AIDR有效波高对比,分析6种方案反演有效波高的准确度,确定了MLE4_SVD(波形重跟踪之前进行滤波)对HY-2A高度计重跟踪更适合反演有效波高。 相似文献