共查询到20条相似文献，搜索用时 54 毫秒
1.
江苏如东西太阳沙及烂沙洋海域潮流泥沙数值模拟 总被引：10，自引：0，他引：10
基于不规则三角形网格有限差分法并考虑波浪及其破碎作用,建立了平面二维潮流场和泥沙场数学模型.该模型对有望建设成深水码头和深水航道的江苏如东西太阳沙和烂沙洋海域的潮流场和泥沙场进行了细化数值模拟.数值模拟结果表明：（1）本海区潮流基本上是顺深槽流动的往复流,潮流流速大,烂沙洋北水道和西太阳沙附近大潮涨落潮最大流速分别在2 m/s和1 m/s以上;（2）本海区的潮平均水体含沙量在0.5 kg/m^3以下,落潮含沙量大于涨潮含沙量;（3）小浪对水体含沙量影响很小,大浪作用下水体含沙量明显增加. 相似文献
2.
3.
4.
依据象山港佛渡水道、牛鼻山水道和狭湾口的实测水文资料,分析3个潮汐通道的潮汐、潮流分布特征及其差异性;建立该水域潮流数值模型,探讨各水道及其交汇处的流场变化特征和影响影响分析。结果显示,狭湾内的涨落潮流主要通过牛鼻山水道受外海潮波的影响,仅在涨落潮流的起始阶段经佛渡水道与崎头洋存在水体交换;牛鼻山水道涨落潮流主要受外海潮波的控制;崎头洋落潮流与外海涨潮流在佛渡水道的交替变化,决定了佛渡水道涨落潮流的方向。佛渡水道涨潮流为东北向,落潮流为西南向。崎头洋通过佛渡水道与象山港进行水体交换,象山港涨、落潮流除了与外海进行水交换外,还受到杭州湾涨、落潮流的影响,有助于对舟山群岛南侧潮波以及杭州湾与外海水体交换的研究。 相似文献
5.
6.
瓯江河口挟沙能力的初步探讨 总被引：10，自引：1，他引：10
在分析瓯江河口潮流泥沙特性基础上 ,认为瓯江口挟沙能力与水动力及泥沙等因素密切相关。采用断面垂线平均的处理方法 ,引入背景含沙量的概念 ,线性回归拟合出瓯江口挟沙能力公式 ,为瓯江口二维潮流泥沙数模计算提供了辅助方程 相似文献
7.
胶州湾海域潮流动力特征及其与含沙量的关系 总被引：1，自引：0，他引：1
根据2009年胶州湾海域的悬沙、流速、流向的实测资料,应用短期资料的潮流准调和分析方法,对连续海流资料进行了分析,并结合悬沙资料,对含沙量与潮流之间动力关系进行了探讨。研究结果表明:该海域潮流属于正规半日潮流性质,半日分潮流的东分量大于北分量,潮流以带有旋转性质的往复流为主,涨潮流流向偏西,落潮流流向偏东。胶州湾内含沙量分布特征与海底沉积物粒径特征基本一致。含沙量在涨落潮的交替和流速的更迭作用下出现明显的周期性变化,含沙量的峰值基本与海域半日潮流特点相对应,几乎每1个流速峰值对应1个含沙量的峰值,含沙量的峰值一般出现在流速峰值之后。胶州湾口处流速和单宽输沙量都为最大,涨潮单宽输沙量大于落潮单宽输沙量,输沙方向为偏西向。 相似文献
8.
建立了以舟山螺头水道海域为重点研究区域的平面二维潮流泥沙数学模型,模型对螺头水道海域2005年1月的悬沙场进行了模拟,将模拟结果与实测资料进行比较,二者吻合较好,模拟结果分析表明:螺头水道内含沙量由西至东逐渐减小,涨落潮主流流路的差异使得水道内存在两股相反的悬沙净输运趋势,但总体净输沙方向为落潮流方向;含沙量与涨落潮流过程密切相关,水道内以平流输沙作用为主,沉降及再悬浮作用小,是长江口及杭州湾向外海输沙的主要通道而非主要沉积区域. 相似文献
9.
人工岛工程对南黄海辐射沙脊群海域潮流泥沙影响研究 总被引：2，自引：0，他引：2
采用MIKE21二维水动力模型模拟了南黄海辐射沙脊群海域的潮流形态和含沙量,模拟结果与实测数据基本一致。在此基础上,模拟计算了围填海工程后辐射沙脊群海域的潮流和含沙量变化。结果显示工程对潮流和含沙量的影响主要出现在工程区附近。围填海工程使原本以弶港为中心呈扇形辐聚、辐散的潮流格局有所改变,形成东沙岛西侧南北向和高泥岛南侧东西向的两条潮流通道,并在一定程度上分割了条子泥南北两侧的水体。工程后含沙量的变化与平均流速的变化基本一致,在流速变大的东沙岛西北侧和高泥岛南侧海域,含沙量显著升高;在流速变小的条子泥南北两侧、东沙岛东侧及西南侧,含沙量显著降低。 相似文献
10.
《海洋通报(英文版)》2015,(1)
本文采用MIKE21二维水动力模型模拟了南黄海辐射沙脊群海域的潮流形态和含沙量,模拟结果与实测数据基本一致。在此基础上,模拟计算了围填海工程后辐射沙脊群海域的潮流和含沙量变化。结果显示工程对潮流和含沙量的影响主要出现在工程区附近。围填海工程使原本以弶港为中心呈扇形辐聚、辐散的潮流格局有所改变,形成东沙岛西侧南北向和高泥岛南侧东西向的两条潮流通道,并在一定程度上分割了条子泥南北两侧的水体。工程后含沙量的变化与平均流速的变化基本一致,在流速变大的东沙岛西北侧和高泥岛南侧海域,含沙量显著升高;在流速变小的条子泥南北两侧、东沙岛东侧及西南侧,含沙量显著降低。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.