共查询到19条相似文献，搜索用时 140 毫秒
1.
不同降雨模式下山谷型垃圾填埋场水分运移及其稳定性研究 总被引：2，自引：0，他引：2
近10年的运营经验表明,国内南方地区第1批建造的山谷型垃圾填埋场中的渗滤液水位一般较高。同时,现有研究表明,降雨入渗引起渗滤液水位过高是垃圾填埋场失稳的主要诱因之一。因此,研究强降雨条件下山谷型垃圾填埋场的水分运移规律及其稳定性,具有重要的现实意义。基于七子山填埋场浅层、中层和深层垃圾土的土-水特征曲线和Brooks-Corey公式,利用非线性拟合技术得到垃圾土的渗透性函数;运用饱和-非饱和渗流理论,对递减型、中心型、增强型和平均型4种降雨模式下七子山填埋场的水分运移进行了数值计算;利用极限平衡理论,对不同降雨模式下七子山填埋场的稳定性进行了分析。结果表明,降雨模式对山谷型垃圾填埋场内的水分运移规律和填埋场的稳定性有显著的影响,递减型降雨模式下填埋场内孔隙水压的变化最大,同时填埋场稳定系数也下降最为明显,为最不利降雨模式;经历7 d 746 mm的极端强降雨后,七子山填埋场具有极大的失稳隐患。 相似文献
2.
垃圾土渗透性和持水性的试验研究 总被引：5，自引：2，他引：3
通过室内常水头试验测定了垃圾土的饱和渗透系数,通过室内压力板仪试验测得垃圾土的土-水特征曲线。基于土-水特征曲线预测了垃圾土的非饱和渗透系数,并通过室内入渗试验进行了初步验证。常水头试验得到深层、中层和浅层垃圾土的饱和渗透系数分别为3.56×10-4、3.50×10-3、4.81×10-2 cm/s。土-水特征曲线试验表明,垃圾土饱和含水率和残余含水率较高,进气值很小,土-水特征曲线在低基质吸力时存在陡降段,其中浅层垃圾土的陡于深层垃圾。验证试验表明,预测得到的非饱和渗透系数与实测结果接近,基于土-水特征曲线预测垃圾土非饱和渗透系数的方法基本可行。 相似文献
3.
为了人类社会的可持续发展,对产量惊人的生活垃圾进行合理地处置成为世界各国亟待解决的问题之。垃圾填埋法是符合处置经济性和技术可行性的理想方案。垃圾填埋场投八运营后,如何防止被填埋垃圾及其次生有害物质进八周围环境,是垃圾填埋场设计环节必须考虑的关键问题之。在城市垃圾填埋场底部衬里系统及封盖系统中设置水力屏障,能有效防止填埋场中所产生的废液、废气向周围环境中迁移。水力屏障通常由土工合成材料与膨润土防水垫或压实粘土组成,形成个多界面的复合衬里或复合封盖体系。这种多界面力学特性以及潜在薄弱面对垃圾填埋场的稳定性具有控制作用,因此成为业界的研究重点。本文依据填埋场封盖和衬里土工合成材料多界面力学特性的最新研究,对所取得的研究成果进行分析和讨论。 相似文献
4.
5.
水泥土强度的影响因素 总被引：26，自引：1，他引：25
水泥浆体搅拌地基加固技术是地基处理的技术方法之一,其水泥—土固结体的强度主要受地基土的含水量、水泥掺入量及地基土类别的影响。本文通过室内及工业性试验表明:土体的含水量对水泥土强度具有负作用;水泥土强度与水泥掺入比不是简单的单调上升关系;地基土的类别对水泥土强度的影响较大,淤泥及淤泥质土由于富含有机质,强度较低,粉质粘土、粘土形成的水泥土强度较高。 相似文献
6.
7.
天然沉积中间土的力学特性研究 总被引：3，自引：2，他引：1
长江口北岸天然沉积土主要由粉粒和细砂粒组成,其渗透系数介于10-7～10-3 cm/s之间,既不属于完全排水的砂性土,也不属于完全不排水的粘性土,针对这样的天然沉积中间土的我国研究并不多见。通过大量的物理力学试验,探讨了天然沉积中间土的物理力学性状,结果表明天然沉积中间土具有类似于软粘土的物理性质,但原位静力触探试验显示其天然沉积中间土的原位强度却与天然含水量分布在塑限附近的硬粘土差不多。研究结果亦表明颗粒分布对天然沉积中间土的原位强度有较大的影响。同时采用灰理论中的关联度分析,对这类中间土物理状态指标与力学特征指标间相关性进行了分析,认为孔隙比用于亚砂土稠度划分,含水比用于亚粘土、粘土稠度划分更加合理 相似文献
8.
利用DSJ-2型电动四联等应变直剪仪分别进行了不同粒径砂和粘土(方案1)、不同含水量砂和粘土(方案2)的直剪试验,揭示了其接触面的力学特性。试验结果表明:法向应力(σn)、砂粒径大小、砂含水量对接触面的力学特性有着重要的影响。方案1和方案2接触面的抗剪强度和达到剪切应力峰值时的剪切位移随着法向应力的增大而增大,当σn为100 kPa时,粘土和不同粒径砂的接触面剪切应力和水平剪切位移(τ-δ)关系曲线呈现应变软化现象;方案1接触面抗剪强度随砂粒径的减小而降低,方案2在σn为100 kPa时,接触面抗剪强度随砂含水量增加而降低,σn>100 kPa时,接触面抗剪强度随砂含水量增加先降低后变大;方案2在低法向应力下,接触面抗剪强度对应的含水量敏感区间为[10%,15%],且较明显。 相似文献
9.
目前对影响土壤饱和渗透系数规律的机理缺乏深刻认识.以不同沉积环境、不同岩性及不同土地利用方式的江汉平原汉江下游浅层土壤为对象,采用改进的TST-55型土壤渗透仪开展室内变水头达西实验.结果表明,研究区内土壤饱和渗透系数平均值为4.94×10-5cm/s,服从对数-正态分布;粉砂壤土冲积物和湖积物的饱和渗透系数平均值为3.53×10-5cm/s和1.98×10-5cm/s,粉砂质粘壤土中,两者分别为8.13×10-7cm/s和5.88×10-7cm/s,同一岩性冲积物的饱和渗透系数较湖积物大;冲积物中,砂壤土、粉砂壤土和粉砂质粘壤土饱和渗透系数平均值为1.98×10-5 cm/s、3.53×10-5 cm/s和8.13×10-7 cm/s,表现为砂壤土>粉砂壤土>粉砂质粘壤土;耕作土壤中,粉砂壤土、粉砂质粘壤土的饱和渗透系数平均值为3.75×10-5 cm/s和8.11×10-7cm/s,非耕作土壤中,两者分别为1.88×10-6cm/s、5.93×10-7cm/s,同一岩性耕作土壤饱和渗透系数较非耕作土壤大. 相似文献
10.
为了研究异质土在不同排水条件下的力学机理,进行了一系列环剪试验,对单一黄土、单一砂、砂-黄土组成的异质土在剪切力学特性上的差异及其产生机理进行了比较分析。结果表明：在不同排水条件下,砂-黄土组成的异质土在相互接触剪切的过程中,剪切应力变化形态和抗剪强度与单一黄土、单一砂之间存在显著差异,即砂-黄土组成的异质土在其剪切过程中呈现出了黏性土的剪切力学特征;在相同剪切速率条件下,砂-黄土组成的异质土在不同排水条件下的抗剪强度比单一黄土和单一砂的抗剪强度至少降低了71%和51%。不同排水条件下砂-黄土的剪切力学性质出现了差异,其主要原因与剪切面处砂与黄土之间的相互作用以及剪切面处土体内孔隙水状态有关。 相似文献
11.
Shear Strength Behavior of Two Landfill Clay Liners 总被引：1，自引：0，他引：1
Direct shear tests were conducted to obtain both the shear strength of compacted clay liners (CCLs) specimens and the interface shear strength between compacted clay liner and base soil. These experiments were conducted under the conditions of five different water contents. The experimental results show that shear strength of both CCLs and CCLs/base interface decreases with the increase in the water content of CCLs and base soil. In addition, the considerate concentration of NaCl in leachate has no deteriorating effect on the shear strength of liners. Triaxial shear tests were also conducted on clay liner specimens to obtain total and effective shear strength under a fast compression. The shear strength c‘=100 kPa for sand-bentonite, respectively. These results indicate that the compacted clay-bentonite shows normal consolidation, but that the compacted sand-bentonite exhibits over-consolidation. 相似文献
12.
将对流-扩散试验装置置于土工离心机中,以50g离心加速度运行12 h,研究了黏土-膨润土混合土样中Cl-的迁移扩散,使用解析解对试验结果进行拟合确定相关参数,分析了试验的相似条件,使用商用软件对离心试验原型进行模拟,与试验结果进行比较,探讨了离心机用于溶质迁移分析的比尺效应,最后通过数值分析研究了试验的黏土-膨润土屏障用于老垃圾填埋场防渗帷幕补强的效果。结果表明,土工离心机试验中,按实际出流量计算的实际孔隙水流速小于临界流速,两试样中的佩克莱数（Pe数）小于临界Pe数,机械弥散的作用可以忽略,试验满足扩散的相似定律;离心机试验所模拟的2.5 m厚衬垫原型,在水头5 m和10 m作用下3.42 a后均未被击穿;常重力下试验土样的渗透系数为8.5×10-8 cm/s,有效扩散系数为7.82×10-7 cm2/s,对试验原型进行的数值模拟表明,n倍重力加速度下,土工离心机可以 尺寸的试样实现对原型的模拟,同时将对流和扩散作用下的溶质迁移时间缩短至原型的 ;试验的黏土-膨润土屏障用于老垃圾填埋场防渗补强,可显著减缓溶质迁移,防渗补强后可满足渗滤液迁移扩散的控制要求。 相似文献
13.
Yahia E.-A. Mohamedzein Amer A. Al-Rawas Mohammed Y. Al-Aghbari Ahmed Qatan Abdul-Hamid Al-Rawas 《Engineering Geology》2005,80(3-4):271-281
The possibility of using crushed shales as landfill liners is investigated in this study. Two types of shales were studied by performing the following laboratory tests: hydraulic conductivity, compaction, swelling, consolidation, X-ray diffraction (XRD), scanning electron microscope (SEM) and chemical analysis. For both compacted shales, the hydraulic conductivity was in order of 10− 7 cm/s or less which satisfies the specifications for landfill liners. The results of XRD and SEM support the low values of the hydraulic conductivity. Because of the dominant presence of low-activity kaolinite, there was no significant change in the hydraulic conductivity when the compacted shales are exposed to calcium chloride solution. The compressibility of the compacted clay was low and no serious post-construction settlement is expected. The shear strength of the compacted shales was within the usual expected range for earthen liners and, therefore, should pose no challenges with respect to shear strength. The crushed shales also satisfy the other criteria related to Atterberg limits and grain size. 相似文献
14.
废旧轮胎胶粉用于填埋场衬垫材料改性,是提高衬垫系统有效性和扩展废旧轮胎资源化利用途径的一种手段。以高岭土作为黏性土的代表,开展废旧轮胎胶粉-高岭土混合土的力学和水力学性质试验,重点探讨胶粉掺量及尺寸对混合土渗透性、压缩性和收缩性的影响规律。研究表明,废旧轮胎胶粉-高岭土混合土的渗透系数、压缩系数、回弹指数、固结系数和体缩率等均随胶粉掺入比的增加而增大。高岭土及混合土的无侧限抗压强度大于200kPa,50kPa和200kPa压力下渗透系数满足≤1.0×10-7cm·s-1的要求,均属于中压缩性土,且体缩率小于体积应变合格值4%。与30目胶粉相比,12目胶粉-高岭土混合土压缩性和回弹量较小、固结系数较大,胶粉尺寸对无侧限抗压强度、体缩率和渗透系数的影响不显著。在本文试验条件下,为提高黏土衬垫对有机污染物的吸附能力并满足渗透性、强度及变形的要求,12目25%胶粉改性黏土可作为填埋场黏土衬垫材料。 相似文献
15.
Amer A. Al-Rawas Yahia E-A. Mohamedzein Abdulaziz S. Al-Shabibi Salem Al-Katheiri 《Geotechnical and Geological Engineering》2006,24(5):1365-1383
Absrtract This paper investigates the potential use of sand–attapulgite (palygorskite) mixtures as a landfill liner. The sand and attapulgite
clay used in this study were brought from Wahiba (eastern Oman) and Al-Shuwamiyah (southern Oman), respectively. Initially
the basic properties of the sand and clay were determined. Then the attapulgite clay was added to the sand at 5, 10, 20 and
30% by dry weight of the sand. The sand–attapulgite clay mixtures were subjected to mineralogical, chemical, microfabric and
geotechnical analyses. The X-ray diffraction (XRD) qualitative analysis showed that attapulgite is the major clay mineral.
The chemical compounds, exchangeable cations and cation exchange capacity (CEC) for the␣samples were determined. The CEC for
the sand–clay mixtures is low but increases with the increase in clay content. The scanning electron microscope (SEM) examination
showed that the addition of clay developed coating between and around the sand grains which results in filling the voids and
reducing the hydraulic conductivity of the sand–clay mixtures. The hydraulic conductivity values for the pure clay and sand
+ 30% clay mixture prepared at 2% above optimum water content are slightly higher than hydraulic conductivity requirements
for landfill liners but can be acceptable. The geotechnical study which included grain size distribution, Atterberg limits,
specific gravity, compaction, hydraulic conductivity and shear strength tests showed that the sand+30% clay mixture prepared
at 2% above optimum water content can be considered to satisfy the requirements for landfill liners. For all sand–clay mixtures
no swelling was recorded and the addition of clay to the sand improved the shear strength. 相似文献
16.
Preventing the penetration of rainwater into a landfill site is the main purpose of the final cover in landfill sites. Conventional designs of landfill covers use geotextiles, such as geomembrane and geosynthetic clay liners, and clay liners to lower the permeability of the final cover of landfill sites. However, differential settlement and climatic effects in landfill sites instigate crack development or structural damage inside the final cover. This study therefore investigates the field applicability of a self-recovering sustainable liner (SRSL) as an alternative to the landfill final cover. The SRSL utilizes the precipitation reaction of two chemical materials to form precipitates that fill the pores and thereby lower the overall permeability of the liner. To examine the field applicability of the SRSL system, uniaxial compression tests and laboratory hydraulic conductivity tests were performed under various climatic effects such as wet/dry and freeze/thaw processes. Furthermore, field-scale hydraulic conductivity tests were performed with intentionally induced cracks to demonstrate the self-recovery performance for practical applications. Extensive laboratory and field test results confirmed the capability of the SRSL final cover system to fulfill the strength and hydraulic conductivity requirements, even in harsh field conditions. 相似文献
17.
Over the last decade, waste disposal has become a particularly sensitive issue in Algeria. New legislation concerning landfill
liner design has been adopted. Traditional methods of landfill liner characterization involve soil sampling and chemical analysis,
which are costly, destructive and time-consuming. New techniques are currently being investigated that aim to provide nondestructive
liner characterisation. This paper details technical aspects associated with electrical conductivity measurements within landfill
liners and presents experimental work to show the direct application of electrical techniques to track ionic movement through
a sand bentonite liner under chemically induced flow. Samples of sand bentonite were mixed and compacted with NaCl electrolytes
at different concentrations. The electrical conductivities of compacted specimens were measured with a two-electrode cell.
The effects of frequency and electrolyte concentration on the conductivity measurement were explored. The relationship between
the soil electrical conductivity and the NaCl electrolyte concentration in interstitial pore fluid was determined. The conductivity
measurements were used to quantify the pore fluid concentration and effective diffusion coefficient of sand bentonite liners.
It is concluded here that the electrical conductivity of compacted specimens depends mainly on the salt concentration in the
pore fluid, and that this approach could therefore be used to track ionic movement through liners during diffusion. 相似文献
18.
《Engineering Geology》2000,56(3-4):293-303
This study aims at investigating the utilization of bottom ash obtained from four different power stations as a construction fill and landfill bottom liner. For the matrix material, commercial powdered bentonite, construction lime and natural clay were used. Compaction tests (Standard Proctor and vibratory hammer) were carried out on the different ratios of bottom ash and matrix material. The optimum water content ranged from 40 to 45% yielding a dry density mostly ca 1 Mg m−3. Uniaxial compressive strength of mixtures ranges from 0.1 to 0.5 kgf cm−2 which showed a 3–20-fold increase when tested on 28-day cured specimens. Triaxial compression tests yield varying rates of shear strength which also showed as high as an 11-fold increase for cured specimens. The hydraulic conductivity of those mixtures was mostly ca 10−4 cm s−1, which is not considered to be low enough for landfill lining. Leaching tests using deionized water were also performed to investigate the possible effect of leachate produced from the mixtures on the environment. In conclusion a light density and environmentally friendly mixture is determined and proposed as construction filler. 相似文献