共查询到20条相似文献，搜索用时 203 毫秒
1.
The dynamic failure mode and energy-based identification method for a counter-bedding rock slope with weak intercalated layers are discussed in this paper using large scale shaking table test and the Hilbert-Huang Transform (HHT) marginal spectrum. The results show that variations in the peak values of marginal spectra can clearly indicate the process of dynamic damage development inside the model slope. The identification results of marginal spectra closely coincide with the monitoring results of slope face displacement in the test. When subjected to the earthquake excitation with 0.1 g and 0.2 g amplitudes, no seismic damage is observed in the model slope, while the peak values of marginal spectra increase linearly with increasing slope height. In the case of 0.3 g seismic excitation, dynamic damage occurs near the slope crest and some rock blocks fall off the slope crest. When the seismic excitation reaches 0.4 g, the dynamic damage inside the model slope extends to the part with relative height of 0.295-0.6, and minor horizontal cracks occur in the middle part of the model slope. When the seismic excitation reaches 0.6 g, the damage further extends to the slope toe, and the damage inside the model slope extends to the part with relative height below 0.295, and the upper part (near the relative height of 0.8) slides outwards. Longitudinal fissures appear in the slope face, which connect with horizontal cracks, the weak intercalated layers at middle slope height are extruded out and the slope crest breaks up. The marginal spectrum identification results demonstrate that the dynamic damage near the slope face is minor as compared with that inside the model slope. The dynamic failure mode of counter-bedding rock slope with weak intercalated layers is extrusion and sliding at the middle rock strata. The research results of this paper are meaningful for the further understanding of the dynamic failure mode of counter-bedding rock slope with weak intercalated layers. 相似文献
2.
Experimental study of motion characteristics of rock slopes with weak intercalation under seismic excitation 总被引：1，自引：0，他引：1
In order to investigate the effect of a weak intercalation on slope stability, a large-scale shaking table model test was conducted to study the dynamic response of rock slope models with weak intercalation. The dynamic response of the prototype slopes were studied in laboratory with the consideration of law of similitude. The initiation failure was observed in the rock slope model with a counter-tilt thin-weak intercalation firstly, not in the slope model with a horizontal thin-weak intercalation. Furthermore, it was interesting that the fracture site is shifted from crest top to the slope surface near the weak intercalation, which is different with the location of failure position in a normal layered slope. We also discussed the effect of the dip angle and the thickness of weak intercalation on the failure mechanism and instability mode of the layered rock slope. From the experimental result, it was noted that the stability of the slope with a counter-tilt weak intercalation could be worse than that of the other slopes under seismic excitation. The findings showed the difference of failure in slopes with a horizontal and counter weak intercalation, and implicated the further evaluation of failure of layered slopes caused by seismic loads. 相似文献
3.
The stability of soil-rock mixtures(SRMs) that widely distributed in slopes is of significant concern for slope safety evaluation and disaster prevention. The failure behavior of SRM slopes under surface loading conditions was investigated through a series of centrifuge model tests considering various volumetric gravel contents. The displacement field of the slope was determined with image-based displacement system to observe the deformation of the soil and the movement of the block during loading in the tests. The test results showed that the ultimate bearing capacity and the stiffness of SRM slopes increased evidently when the volumetric block content exceeded a threshold value. Moreover, there were more evident slips around the blocks in the SRM slope. The microscopic analysis of the block motion showed that the rotation of the blocks could aggravate the deformation localization to facilitate the development of the slip surface. The high correlation between the rotation of the key blocks and the slope failure indicated that the blocks became the dominant load-bearing medium that influenced the slope failure. The blocks in the sliding body formed a chain to bear the load and change the displacement distribution of the adjacent matrix sand through the block rotation. 相似文献
4.
As a combined supporting structure,the anchor cable and lattice beam have a complex interaction with the slope body.In order to investigate the seismic behaviors of the slope reinforced by anchor cable and lattice beam,a largescale shaking table test was carried out on a slope model(geometric scale of 1:20)by applying recorded and artificial seismic waves with different amplitudes.The acceleration and displacement of the slope,the displacement of lattice beam and the axial force of anchor cable were obtained to study the interaction between the slope and the supporting structure.The test results show that:(1)the acceleration responses of the slope at different relative elevations display obvious nonlinear characteristics with increasing of the peak ground acceleration(PGA)of the inputted seismic waves,and the weak intercalated layer has a stronger effect on acceleration amplification at the upper part of the slope than that at the lower part of the slope;(2)the frequency component near the second dominant frequency is significantly magnified by the interaction between the slope and the supporting structure;(3)the anchor cables at the upper part of the slope have larger peak and residual axial forces than that at the lower part of the slope,and the prestress loss of the anchor cable first occurs at the top of the slope and then passes down;(4)the peak and residual displacements inside the slope and on the lattice beam increase with the increase of relative elevation.When the inputted PGA is not greater than 0.5 g,the combined effect of anchor cable and lattice beam is remarkable for stabilizing the middle and lower parts of the potential sliding body.The research results can provide a reference for the seismic design of such slope and the optimization of supporting structure. 相似文献
5.
Large-scale shaking table tests were conducted to study the dynamic response of a slope reinforced by double-row anti-sliding piles and prestressed anchor cables. The test results show that the reinforcement suppressed the acceleration amplification effectively. The axial force time histories are decomposed into a baseline part and a vibration part in this study. The baseline part of axial force well revealed the seismic slope stability, the peak vibration values of axial force of the anchor cables changed significantly in different area of the slope under seismic excitations. The peak lateral earth pressure acting on the back of the anti-sliding pile located at the slope toe was much larger than that acting on the back of the anti-sliding pile located at the slope waist. The test results indicate an obvious load sharing ratio difference between these two anti-slide piles, the load sharing ratio between the two anti-sliding piles located at the slope toe and the slope waist varied mainly in a range of 2-5. The anti-slide pile at the slope waist suppressed the horizontal displacement of the slope surface. 相似文献
6.
This study discussed how cavity gas pressure affects the stability of rock mass with fractures under well controlled laboratory experiments. Suddenly-created void space created and the induced gas pressures have been the focus of active researches because they are associated with fast movement of large-scale landslides. A shaking table experiment was set up to mimic weak-intercalated rock slope under seismic loads. Excessive cavity gas pressure would be produced in weak spots upon a sudden vibration load. The drastically elevated gas pressure is believed to be responsible for the creation of cavities surrounding the tension fracture. With dissipation of the excessive cavity gas pressure, the fractures are in unbounded closed-state. This observation explains that the slope body would be split and loosened under several aftershocks, and with the expanding of the cracks, the slope failure eventually occurred. The research of the mechanism of cavity gas pressure could provide a novel insight into the formation mechanism of landslides under seismic load and has implications for the disaster prevention and control theory for the slope stability evaluation. 相似文献
7.
During the construction of some large-scale rock engineering, high-steep slopes and insufficient slope stability induced by unloading fissures are often encountered. For the reinforcement of these slopes, some techniques (including conventional pre-stressed anchoring cable and unconventional anchoring hole) are usually utilized, however, having several obvious defects. Thus, it is very difficult for a designer to design an efficient reinforcement scheme for the high-steep slopes. For this reason, the authors develop the pre-stressed anchoring beam technique, in which tensile capacity of pre-stressed structures are fully utilized. It is analyzed that the new technique is characterized by multi-functions, including engineering investigation, efficient reinforcement, drainage, monitoring and urgent strength supplement, and hoped to be extensively applicable in the reinforcement of high-steep slopes. 相似文献
8.
Zhifa YANG Luqing ZHANG Jiewang ZHU 《东北亚地学研究》2006,9(2):213-216
During the construction of some large-scale rock engineering, high-steep slopes and insufficient slope stability induced by unloading fissures are often encountered. For the reinforcement of these slopes, some techniques （including conventional pre-stressed anchoring cable and unconventional anchoring hole） are usually uti- lized, however, having several obvious defects. Thus, it is very difficult for a designer to design an efficient reinforcement scheme for the high-steep slopes. For this reason, the authors develop the pre-stressed anchoring beam technique, in which tensile capacity of pre-stressed structures are fully utilized. It is analyzed that the new technique is characterized by multi-functions, including engineering investigation, efficient reinforcement, drainage, monitoring and urgent strength supplement, and hoped to be extensively applicable in the reinforcement of high-steep slopes. 相似文献
9.
Interest in rock slope stability in mountainous regions has increased greatly in recent years.This issue has become a topic of major interest for geoscientists and engineering professionals,as well as for private citizens and local administrators,in many parts of the world.This paper evaluates the stability of seven rock slopes along the KamyaranMarivan tourist road,Kurdistan province,Iran,using various methods.The two main reasons for performing this research were to determine whether different methods of stability analysis provide the same results,and to determine how different factors such as the presence of water,tension cracks,and seismic forces affect the stability of these rock slopes.Firstly,field investigations were performed to obtain the engineering characteristics of the rock masses,discontinuities,and intact rocks of the slopes.Secondly,laboratory tests were carried out on rock samples obtained from the slopes,to determine the engineering properties of the intact rocks.Then for each rock slope,the contour diagram of discontinuities and slope face was drawn in the Dips v.5.1 software environment,and the failure mechanism was determined based on the kinematic or stereographic method.Next,the factors of safety of the rock slopes were calculated using the limit equilibrium method,based on the failure mechanisms resulting from the kinematic method.The accuracy of the results obtained by these two methods was investigated using SWedge v.4.0 software.The results indicated that four rock slopes have a potential for plane,wedge,and toppling failure,and three others are stable.Also,it was found that the stability of the studied rock slopes decreases greatly in the presence of water,tension cracks,and seismic forces. 相似文献
10.
《中国海洋大学学报(英文版)》2021,(5)
Marine geological disasters occurred frequently in the deep-water slope area of the northern South China Sea, especially submarine landslides, which caused serious damage to marine facilities. The cyclic elastoplastic model that can describe the cyclic stress-strain response characteristic for soft clay, is embedded into the coupled Eulerian-Lagrangian(CEL) algorithm of ABAQUS by means of subroutine interface technology. On the basis of CEL technique and undrained cyclic elastoplastic model, a method for analyzing the dynamic instability process of marine slopes under the action of earthquake load is developed. The rationality for cyclic elastoplastic constitutive model is validated by comparing its calculated results with those of von Mises model built in Abaqus. The dynamic instability process of slopes under different conditions are analyzed. The results indicate that the deformation accumulation of soft clay have a significant effect on the dynamic instability process of submarine slopes under earthquake loading. The cumulative deformation is taken into our model and this makes the calculated final deformation of the slope under earthquake load larger than the results of conventional numerical method. When different contact conditions are used for analysis, the smaller the friction coefficient is, the larger the deformation of slopes will be. A numerical analysis method that can both reflect the dynamic properties of soft clay and display the dynamic instability process of submarine landslide is proposed, which could visually predict the topographies of the previous and post failure for submarine slope. 相似文献
11.
Continuum and discrete element coupling approach to analyzing seismic responses of a slope covered by deposits 总被引：1，自引：1，他引：0
Numerical analyses of earthquake effects on the deformation, stability, and load transfer of a slope covered by deposits are
traditionally based on the assumption that the slope is a continuum. It would be problematic, however, to extend these approaches
to the simulation of the slide, collapse and disintegration of the deposits under seismic loading. Contrary to this, a discrete
element method (DEM) provides a means to consider large displacement and rotation of the non-continuum. To take the advantages
of both methods of continuum and non-continuum analyses, seismic responses of a slope covered by deposits are studied by coupling
a two-dimensional (2-D) finite difference method and a 2-D DEM, with the bedrock being modelled by the finite difference grids
and the deposits being represented by disks. A smooth transition across the boundaries of the continuous/discontinuous domains
is obtained by imposing the compatibility condition and equilibrium condition along their interfaces. In the course of computation,
the same time-step value is chosen for both continuous and discontinuous domains. The free-field boundaries are adopted for
lateral grids of bedrock domain to eliminate the radiation damping effect. When the static equilibrium under gravity load
is obtained, dynamic calculation begins under excitation of the seismic wave input from the continuum model bottom. In this
way, responses to the earthquake of a slope covered by deposits are analyzed dynamically. Combined with field monitoring data,
deformation and stability of the slope are discussed. The effects of the relevant parameters of spectrum characteristic, duration,
and peak acceleration of seismic waves are further investigated and explained from the simulations. 相似文献
12.
新疆塔县地区广泛分布的大规模片麻岩崩塌、滑坡主要是由于长期地震力循环作用下岩体劣化所致。为揭示该地区片麻岩在地震力作用下的劣化损伤机理,采用在不同应力水平条件下对片麻岩岩样进行循环荷载试验和三轴压缩试验的方法,分析了片麻岩阻尼参数及循环加、卸载前后三轴抗压强度的变化规律。研究结果表明:片麻岩阻尼比和阻尼系数随着循环荷载次数的增加而逐渐降低,随着应力水平的升高而增大;循环荷载作用后,片麻岩的三轴抗压强度均明显降低,且应力水平越高,降低的幅度越大;此外,片麻岩内部矿物颗粒的相互摩擦,原生微裂隙、孔洞的张开、闭合以及次生裂隙的产生、发展是导致其劣化损伤的主要机制。总的来说,长期地震力作用下,研究区片麻岩由于内部劣化损伤导致的力学性质降低,是该区域广泛发育大规模崩塌、滑坡等地质灾害的主要原因之一。 相似文献
13.
在大量的野外地质调查工作基础之上,采用赤平投影法分析了沉积岩地区岩石高边坡的潜在破坏模式,并运用极限平衡法计算边坡在此潜在破坏模式下的稳定性,对安全储备较低的采石场边坡提出削坡方案,同时配合有限元法对边坡的稳定性进行了分析和评价,指出岩层层面是影响沉积岩地区高边坡稳定性的最不利结构面,是调查和研究的重点。 相似文献
14.
The excavated height of the left bank slope of the diversion power system intake in Jinchuan hydropower station is about 16o m. The stability and safety of the slope during construction and its operation/utilization become one of the most important geological engineering problems. At the same time, it is also crucial to select a safe and economic excavation gradient for the construction. We studied the problem of how to select a safe and economic slope ratio by analyzing the geological condition of the high slope, including the lithology, slope structure, structural surface and their combinations, rock weathering and unloading, hydrology, and the natural gradient. The study results showed that the use of an excavation gradient larger than the gradient observed during site investigation and the gradient recommended in standards and field practice manuals is feasible. Then, we used the finite element method and rigid limit equilibrium method to evaluate the stability of the excavation slope under natural, rainstorm and earthquake conditions. The calculated results showed that the excavated slope only has limited failure, but its stability is greatly satisfactory. The research findings can be useful in excavation and slope stabilization projects. 相似文献
15.
The"5.12"Wenchuan earthquake in 2008 triggered a large number of co-seismic landslides.The rear boundary or cracks of co-seismic landslide are generally located at the steep free surface of thin or thick mountains.Dynamic process of this kind of landslides could be divided into two parts:the seismic dynamic response of the slope and the movement process of rock mass.Taking the Laoyingyan rockslide as an example,the amplification effect was studied by single-degree-of-freedom system analysis method.Besides,the dynamic process of landslide under seismic loading was simulated by the finite difference method(FDM)and discrete element method(DEM).The amplification coefficient of the rockslide to seismic wave is 1.25.The results show that the critical sliding surface of the Laoyingyan rockslide was formed at the 23 th seconds under the action of seismic wave.At the same time,tension failure occurred at the rear edge of the sliding mass and shear failure occurred at the front edge.The maximum displacement was 0.81 m and the initial velocity was 2.78 m/s.During the initiation process of the rockslide,the rock mass firstly broke down along the joints which are along the dip of the rock stratum,and then collapsed bodily along the secondary structural planes.In the process of movement,the maximum velocity of rock mass was 38.24 m/s.After that,the rock mass underwent multiple collisions,including contact,deceleration to 0 and speed recovery after rebound.Finally,due to the constant loss of energy,the rocks stopped and accumulated loosely at the foot of the slope.The longest distance of movement was about 494 m.Besides,the smaller the damping ratio,the farther the rock mass moved.Compared with the results without considering the amplification factor,the movement distance of landslide by considering the amplification factor was more accurate.The study of the Laoyingyan rockslide is helpful to strengthen our field identification of potential co-seismic rockslides.At the same time,understanding its movement and accumulation process can help us better predict the hazard scope of the co-seismic rockslides,and provide a reference for the design of treatment projects. 相似文献
16.
Study on Dynamic Response of the ＂Dualistic＂ Structure Rock Slope with Seismic Wave Theory 总被引：2，自引：1，他引：1
Currently, scant attention has been paid to the theoretical analysis on dynamic response mechanism of the ＂Dualistic＂ structure roek slope. The analysis presented here provides insight into the dynamic response of the ＂Dualistie＂ structure rock slope. By investigating the principle of energy distribution, it is shown that the effect of a joint plays a significant role in slope stability analysis. A dynamic reflection and transmission model （RTM） for the ＂Dualistic＂ structure rock slope and explicit dynamic equations are established to analyze the dynamic response of a slope, based on the theory of elastic mechanics and the principle of seismic wave propagation. The theoretical simulation solutions show that the dynamic response of the ＂Dualistic＂ structure rock slope （soft-hard） model is greater than that of the ＂Dualistic＂ strueture rock slope （hard-soft） model, especially in the slope crest. The magnifying effect of rigid foundation on the dynamic response is more obvious than that of soft foundation. With the amplitude increasing, the cracks could be found in the right slope （soft-hard） crest. The crest failure is firstly observed in the right slope （soft-hard） during the experimental process. The reliability of theoretical model is also investigated by experiment analysis. The conclusions derived in this paper could also be used in future evaluations of Multi-layer rock slopes. 相似文献
17.
高位危岩崩塌极具隐蔽性、突发性和灾难性,传统的接触式调查方法在安全性方面无法完全保障并且也难以彻底查清边坡上各危岩块体的空间分布及发育特征,因此如何安全快速准确地获取边坡面上关键地质信息,一直是崩塌地质灾害调查及评价研究中的难点之一,也是防灾减灾工作中极为重要的环节。以连云港市某矿区高陡岩质边坡为例,提出了一套基于无人机倾斜摄影技术的崩塌隐患早期识别及影响区划分方法体系,该方法体系通过倾斜摄影技术获取研究区高分辨率影像及构建三维高精度地质模型,在此基础上利用测线法提取并统计边坡优势结构面空间展布特征及相关参数,利用赤平投影法对矿区高边坡关键危岩块体失稳模式进行判别,在完成关键危岩块体稳定性评价并划分稳定等级的前提下使用Rocfall模拟最不利工况下崩落体失稳后的滚落运动特征,从而划分出不同级别的崩塌影响区,为最终的地质灾害防治提供依据。研究表明,无人机倾斜摄影技术在崩塌隐患早期识别、破坏模式分析、稳定性评价以及崩落体威胁范围划定等方面具有显著的可行性和优越性。所提出的基于无人机倾斜摄影技术的崩塌隐患早期识别及影响区划分方法体系具有重要的参考价值。 相似文献
18.
In recent major earthquakes, the researchers have found the need for consideration of vertical seismic acceleration for the stability analysis of the man-made and natural slopes. However, in most past studies, the performance of slopes has been assessed by accounting only the horizontal seismic component of the ground motion, without giving due weightage to the effect of vertical component. In the present study, analytical expressions are derived to determine the factor of safety, yield seismic coefficient and consequently the seismic displacement of cohesionless soil slope under combined horizontal and vertical components of the ground motion. The derivation uses the Newmark’s sliding block approach, in which the soil slope with a planar failure surface within the framework of conventional pseudo-static analysis is assumed to follow the Mohr-Coulomb failure criterion. The effects of vertical seismic coefficient on the stability of cohesionless slope have been studied through a set of graphical presentations for a specific range of soil parameters. It is observed that overlooking the effect of the vertical component of the ground motion on factor of safety and the displacement while designing the slope may be detrimental, resulting in the slope failure. The general expressions presented in this paper may be highly useful in the field of earthquake geotechnical engineering practice for designing the cohesionless soil slopes under combined horizontal and vertical seismic loads. 相似文献
19.
在持续降雨或开挖卸荷作用下, 土体的强度指标会发生劣化, 但现今采用的边坡稳定性计算大多直接将其视为一个常数。为接近真实的边坡失稳破坏模式, 基于瑞典条分法以及一阶线性应变软化机制, 提出了一种边坡渐进破坏分析新方法, 推导出应变软化型边坡极限平衡表达式, 并获得了各破坏进度下边坡的安全系数。通过对模拟算例进行分析, 证明了条分-软化法的可靠性, 且计算结果表明渐进破坏过程中安全系数不仅取决于边坡的破坏方式与强度参数, 还与岩土体的软化模量密切相关。同时, 通过与滑坡实际案例的对比验算, 证实其强度指标存在不同的衰减系数, 即黏聚力的衰减系数大于摩擦角。从理论到应用, 最终获得的条分-软化法, 不仅考虑了岩土体的强度劣化效应以及滑动面的渐进发展, 还能有效地服务于实际工程背景下边坡的稳定性分析, 可以为滑坡的预防与治理提供指导建议。 相似文献
20.
Modelling the flexural buckling failure of stratified rock slopes based on the multilayer beam model
The buckling failure of stratified rock slopes intersected by a set of steep discontinuities that are approximately parallel to the slope surface is frequently encountered while constructing railways and roadways in mountainous areas. In this study, an analytical approach based on the energy equilibrium principle is presented to solve the flexural buckling stability of stratified rock slopes within the framework of multilayer beam theory. The generalized HoekBrown failure criterion is introduced to reflect the influences of slope size(scale effects) on the buckling stability. Subsequently, numerical and physical modellings from previous literatures are employed to validate the proposed approach. Furthermore, a practical case of Bawang Mountain landslide is also used for the comparative analysis. The study shows that the present analytical approach is capable to provide a more reasonable assessment for the buckling failure of stratified rock slopes, compared with several existing analytical approaches. Finally, a detailed parametric study is implemented, and the results indicate that the effects of rock strength, rock deformation modulus, geological strength index, layer thickness and disturbance degree of rock mass on the buckling failure of stratified rock slopes are more significant than that of rock type and slope angle. 相似文献