共查询到20条相似文献，搜索用时 62 毫秒
1.
为研究土质边坡深层滑移失稳机制, 以京广铁路下行线K1219+000处路基边坡失稳为例, 通过现场调查测绘、工程地质钻探、原位试验和室内试验、深部位移监测和数值模拟等手段, 详细研究了该土质边坡变形破坏特征、地质力学过程和失稳模式。结果表明: 路基边坡表面裂缝宽度及深度呈坡顶至坡脚逐渐变浅变窄, 变形具有一定的旋转性, 牵引式特征明显, 属于深层滑移拉裂式失稳; 土质边坡经历了因坡脚开挖、抽水引起的应力场和渗流场重新分布阶段、雨水入渗软化导致下滑力不断增大而滑面逐渐迁移扩大加深阶段以及支挡结构抗力失效阶段3个地质力学过程, 其失稳模式包括浅层滑移、浅层滑面向深层迁移、动荷载触发深层滑移失稳3个阶段。在此基础上, 综合确定了滑面位置, 并通过反演方法确定了滑面力学参数。研究采用了刚架式双排抗滑桩的整治方案, 通过理论计算和数值分析, 边坡变形与抗滑桩变形基本一致, 且与监测结果整体吻合, 这表明土质边坡深层失稳理论分析准确且计算的力学参数科学, 整治对策稳妥、可靠。 相似文献
2.
Mountainous torrents often carry large amounts of loose materials into the rivers, thus causing strong sediment transport. Experimentally it was found for the first time that when the intensive sediment motion occurs downstream over a gentle slope, the siltation of the riverbed is induced and the sediment particles can move upstream rapidly in the form of a retrograde sand wave, resulting in a higher water level along the river. To further study the complex mechanisms of this problem, a sediment mass model in the framework of the Smoothed Particle Hydrodynamics(SPH) method was presented to simulate the riverbed evolution, sediment particle motion, and the generation and development of dynamic hydraulic jump under the condition of sufficient sediment supply over a steep slope with varying angles. Because the sediment is not a continuous medium, the marker particle tracking approach was proposed to represent a piece of sediment with a marked sediment particle. The twophase SPH model realizes the interaction between the sediment and fluid by moving the bed boundary particles up and down, so it can reasonably treat the fluid-sediment interfaces with high CPU efficiency. The critical triggering condition of sediment motion, the propagation of the hydraulic jump and the initial siltation position were all systematically studied. The experimental and numerical results revealed the extra disastrous sediment effect in a mountainous flood. The findings will be useful references to the disaster prevention and mitigation in mountainous rivers. 相似文献
3.
三峡水库蓄水使得库岸大量土体长期处于浸泡状态,导致土体软化从而诱发滑坡失稳。为研究长期浸泡对滑坡土体物理-化学-力学性质的影响,以马家沟滑坡原状滑带土为对象开展了浸泡软化试验,通过比较不同浸泡时间滑带土的粒度分布、界限含水率、化学与矿物成分、剪切特性等特征,探讨了滑带土浸泡软化机理。研究结果表明:浸泡过程中滑带土中Ca2+、Mg2+等离子流失较多,但矿物成分无变化;浸泡后滑带土出现阶段性粒度细化现象,液塑限和塑性指数均随黏粒含量增加而增大;随着浸泡时间增加,滑带土应力应变关系在低法向应力下由强软化型变为弱软化型,在高法向应力下由软化型变为硬化型;滑带土抗剪强度参数随着浸泡时间增加呈指数形式降低,黏聚力c降低程度大于内摩擦角φ。研究成果可以为水库滑坡稳定性评价提供理论依据。 相似文献
4.
水库蓄水后, 滑坡体碎石土经受长时期的浸泡, 力学性质发生改变, 从而影响滑坡整体稳定性。为探究浸泡对碎石土力学性质的影响规律, 选取三峡库区马家沟滑坡后缘未经受长期浸泡作用的碎石土进行大型直剪试验, 分析了不同浸泡天数下碎石土的剪切力学性质。试验结果表明: 浸泡40 d后, 碎石土黏聚力下降幅度达39%, 内摩擦角下降幅度为8.3%;碎石土黏聚力在浸泡前期快速下降, 下降速率随浸泡天数增加而降低, 浸泡20 d后, 黏聚力基本达到稳定。为探究碎石土抗剪强度降低的原因和机理, 对粉质黏土(碎石土细粒成分)进行了三轴剪切试验、激光粒度分析及浸出液阳离子分析等试验, 揭示了碎石土抗剪强度的衰减机理为: 浸泡作用下, 碎石土中的粉质黏土发生矿物溶解、离子交换与吸附作用, 土体中大颗粒细化, 胶结作用减弱, 进而导致碎石土整体抗剪强度降低。研究结果对库区碎石土滑坡评价与治理具有一定的指导意义。 相似文献
5.
The initiation mechanism of debris flow is regarded as the key step in understanding the debris-flow processes of occurrence, development and damage. Moreover, migration, accumulation and blocking effects of fine particles in soil will lead to soil failure and then develop into debris flow. Based on this hypothesis and considering the three factors of slope gradient, rainfall duration and rainfall intensity, 16 flume experiments were designed using the method of orthogonal design and completed in a laboratory. Particle composition changes in slope toe, volumetric water content, fine particle movement characteristics and soil failure mechanism were analyzed and understood as follows: the soil has complex, random and unstable structures, which causes remarkable pore characteristics of poor connectivity, non-uniformity and easy variation. The major factors that influence fine particle migration are rainfall intensity and slope. Rainfall intensity dominates particle movement, whereby high intensity rainfall induces a large number of mass movement and sharp fluctuation, causing more fine particles to accumulate at the steep slope toe. The slope toe plays an important role in water collection and fine particle accumulation. Both fine particle migration and coarse particle movement appears similar fluctuation. Fine particle migration is interrupted in unconnected pores, causing pore blockage and fine particle accumulation, which then leads to the formation of a weak layer and further soil failure or collapses. Fine particle movement also causes debris flow formation in two ways: movement on the soil surface and migration inside the soil. The results verify the hypothesis that the function of fine particle migration in soil failure process is conducive for further understanding the formation mechanism of soil failure and debris flow initiation. 相似文献
6.
Landslides & debris flows formation from gravelly soil surface erosion and particle losses in Jiangjia Ravine 总被引：1，自引：1，他引：0
Gravelly soils are made up of gravel, sand, silt and clay. They are widely used in engineering applications such as rock-fill dams with clay cores, which are the main researches at present. The strength and mechanical properties of the gravelly soils are affected by the content of coarse grain, fine particles, and their adhesive states. These Properties can be verified by laboratory unconsolidated undrained triaxial tests with grain size less than 5 mm and by large scale direct-shear tests with original grain content. Fine particles of the loose gravelly slopes are released under rainfalls, alternated the structures and mechanical properties, even affected the slope stability. There are a series of large scale direct-shear tests with different coarse grain contents to study the influence of fine particles releasing and migration, results showed the strength behavior of the gravelly soils were affected by the coarse grain content （5） and the inflection coarse grain contents. In order to study the erosion features of the gravelly soil slopes on rainfall conditions and the slopes stability alteration, we had carried out one sort of artificial rainfall local and model experiments, the runoff sediment contents were monitored during the experiments. Result showed that the shapes of the slopes surface transformed periodically, runoff sediment contents were divided into five phases according to the experiment phenomena, runoff sediment contents maintained downtrend during the rain time and the downtrend was obviouslyinterpreted by one descend belt no matter the rainfall intensity and the slope angels. Particle size analysis released the deposit on the slope surface lost almost all of the clay, most of the silt and sand after the experiments, this meant the fine particles releasing, migration and accumulation process on condition of rainfall resulted in the instability factor of the slopes even induced landslide or debris flow. 相似文献
7.
When transparent soil technology is used to study the displacement of a slope, the internal deformation of the slope can be visualized. We studied the sliding mechanism of the soil-rock slope by using transparent soil technology and considering the influence of the rock mass Barton joint roughness coefficient, angle of the soil mass, angle of the rock mass and soil thickness factors on slope stability. We obtained the deformation characteristics of the soil and rock slope with particle image velocimetry and the laser speckle technique. The test analysis shows that the slope sliding can be divided into three parts: displacements at the top, the middle, and the bottom of the slope; the decrease in the rock mass Barton joint roughness coefficient, and the increase in soil thickness, angles of the rock mass and soil mass lead to larger sliding displacements. Furthermore, we analyzed the different angles between the rock mass and soil thickness. The test result shows that the displacement of slope increases with larger angle of the rock mass. Conclusively, all these results can help to explain the soil-rock interfacial sliding mechanism. 相似文献
8.
《山地科学学报》2019,(11)
Mud inrush in mountain tunnel is an independent geological hazard type different from water inrush, landslide and debris flow. The intrinsic factor of mud inrush is the instability failure of disaster medium. Its essence is that when the cohesion decreases gradually with the increase of void ratio to the point where the movement of soil particles cannot be restricted, soil particles and groundwater form slurry and gush out. Thus, accurate calculation of cohesion with variable void ratios is crucial for analyzing the reliability of disaster medium. In this study, the disaster medium was regarded as graded soil and a structural model was established wherein soil particles were simplified as cubes and the interparticle pores were represented by the clearance between cubes. On the basis of the structure model of disaster medium, a function between the soil particle distance and void ratio was derived. Cohesion is equivalent to the resultant force between soil particles per unit area; thus, a cohesion function was derived in which the void ratio is the main variable. This function considers the influence of gradationcharacteristics on cohesion variation and is generally applicable to various types of disaster medium. A series of direct shear tests were carried out to determine the cohesion variation for different types of disaster medium with variable void ratios. By comparing the variation of cohesion obtained through direct shear tests with those deduced by the proposed cohesion function, we verified the validity and general applicability of the cohesion function. It is of great significance because the cohesion function can accurately predict the variation of cohesion by using the void ratio, and effectively evaluate the possibility of mud inrush according to the initial mechanical properties of disaster medium. 相似文献
9.
The erosion shape and the law of development of debris flow sabo dam downstream is a weak part in the study on debris flow erosion. The shape and development of scour pit have an important effect on the stability and safety of debris flow sabo dam, which determines the foundational depth of the dam and the design of protective measures downstream. Study on the scouring law of sabo dam downstream can evaluate the erosion range and reasonably arrange auxiliary protective engineering. Therefore, a series of flume experiments are carried out including different debris flow characteristics （density is varying from 1.5 t/m3 to 2.1 t/m~） and different gully longitudinal slopes. The result shows that the scour pit appears as an oval shape in a plane and deep in the middle while superficial at the ends in the longitudinal section, the position of the maximum depth point moves towards downstream with an increase of flume slope angle. The maximum depth of scour pit is mainly affected by the longitudinal slope of gully, density of debris flow, and the characteristics of gully composition （particle size and the viscosity of soil）. The result also indicates that the viscosity of soil will weaken the erosion extent. The interior slopes of scour pit are different between the upstream and the downstream, and the downstream slope is smaller than the upper one. For the viscous and non-viscous sands with the same distribution of gradation, the interior slope of non- viscous sand is smaller than the viscous sand.According to tbe regression analysis on the experimental data, the quantitative relationship between the interior slope of scour pit, slope of repose under water and the longitudinal slope of gully is established and it can be used to calculate the interior slope of scour pit. The results can provide the basis for the parameter design of the debris flow control engineering foundation. 相似文献
10.
《山地科学学报》2020,17(10):2577-2590
Based on the principle of saturated infiltration and the Green-Ampt model, an unsaturated infiltration model for a soil slope surface was established for either constant moisture content, or depth-varying moisture content and the slope. Infiltration parameters in the partially saturated slope were revealed under sustained rainfall. Through analysis of the variation of initial moisture content in the slope, the ponding time, infiltration depth, and infiltration rate were deduced for an unsaturated soil slope subject to rainfall infiltration. There is no ponded water on the surface of the slope under sustained low-intensity rainfall. The results show that the infiltration parameters of an unsaturated slope are influenced by the initial moisture content and the wetting front saturation, the soil cohesion and rainfall intensity under sustained rainfall. More short-term slope failures can occur with the decrease of cohesion of the soil of the slope. The ponding time and infiltration depth differ considering constant or different initial moisture content respectively in the soil slope. Then, best-fit curves of the infiltration rate, ponding time, and infiltration depth to the wetting front saturation were obtained with constant or different initial moisture contents. And the slope failure time is roughly uniform when subject to a rainfall intensity I5 mm/h. 相似文献
11.
Discontinuous slope failures and pore-water pressure variation 总被引：1，自引：1，他引：0
Field experiments were conducted under artificial rainfalls to investigate the processes of soil failures on slope. It is found that the failures were temporally discontinuous and spatially discrete, with a wide range of magnitudes, accompanied by variations of soil moisture and pore-water pressure. Specifically, the experiments indicate that soil failures are more likely to occur on slope with high content of fine particles; the pore-pressure varies in response to soil failures in that the failures evidently affect the pore of the underlying soil. Migration of fine particles from upper to lower part of the slope also impacts the pore-water pressure variations in the slope profile. It is concluded that soil heterogeneity has a significant effect on variation in pore-water pressure, and fine particles transportation influences the building of pore-water pressure, as well as the mass depth, initial porosity, which is key to understanding the spatial characteristics of slope failures. 相似文献
12.
In recent major earthquakes, the researchers have found the need for consideration of vertical seismic acceleration for the stability analysis of the man-made and natural slopes. However, in most past studies, the performance of slopes has been assessed by accounting only the horizontal seismic component of the ground motion, without giving due weightage to the effect of vertical component. In the present study, analytical expressions are derived to determine the factor of safety, yield seismic coefficient and consequently the seismic displacement of cohesionless soil slope under combined horizontal and vertical components of the ground motion. The derivation uses the Newmark’s sliding block approach, in which the soil slope with a planar failure surface within the framework of conventional pseudo-static analysis is assumed to follow the Mohr-Coulomb failure criterion. The effects of vertical seismic coefficient on the stability of cohesionless slope have been studied through a set of graphical presentations for a specific range of soil parameters. It is observed that overlooking the effect of the vertical component of the ground motion on factor of safety and the displacement while designing the slope may be detrimental, resulting in the slope failure. The general expressions presented in this paper may be highly useful in the field of earthquake geotechnical engineering practice for designing the cohesionless soil slopes under combined horizontal and vertical seismic loads. 相似文献
13.
In China,gravity retaining walls are widely used as protection structures against rockfalls,debris flows and debris avalanches along the roads in mountainous areas.In this paper,the Discrete Element Method(DEM) has been used to investigate the impact of granular avalanches and debris flows on retaining walls.The debris is modeled as two dimensional circular disks that interact through frictional sliding contacts.The basic equations that control the deformation and motion of the particles are introduced.A series of numerical experiments were conducted on an idealized debris slide impacting a retaining wall.The parametric study has been performed to examine the influences of slope geometry,travel distance of the sliding mass,wall position,and surface friction on the impact force exerted on the wall.Results show that:1) the force achieves its maximum value when slope angle is equal to 60°,as it varies from 30° to 75°;2) an approximate linear relationship between the impact force and the storage area length is determined. 相似文献
14.
Water sensitivity phenomenon occurs during saline aquifer freshening process in seawater intrusion area, and clay particles released in the phenomenon can damage the infiltration capacity of the aquifer. In order to find out the factors and mechanisms for clay particle release, laboratory column infiltration experiments simulating saline aquifer freshening process were designed to measure the critical conditions(critical flow velocity, critical salt concentration and critical ionic strength) and force analysis for clay particle according to DLVO electric double layer theory was employed to illustrate the mechanisms for particle release. The research results showed that critical flow velocity for clay particle release is influenced by salt concentration of injecting solution. When salt concentration of injecting solution is very high, clay particles are not released, indicating that there does not exist a critical flow velocity in this situation. As salt concentration of injecting solution decreases, particles start to be released. The critical salt concentration for clay particle release is 0.052 mol L-1 in our work, which was determined by a constant-flux experiment for stepwise displacement of high concentration Na Cl solution. The critical ionic strength for clay particle release decreases as Ca2+ molar content percentage of the mixed solution of Na Cl and Ca Cl2 increases following the first-order exponential decay equation y = 0.0391e-0.266 x + 0.0015. 相似文献
15.
Mass-front velocity of dry granular flows influenced by the angle of the slope to the runout plane and particle size gradation 总被引：2，自引：0，他引：2
The mass-front velocities of granular flows results from the joint action of particle size gradations and the underlying surfaces.However,because of the complexity of friction during flow movement,details such as the slope-toe impedance effects and momentum-transfer mechanisms have not been completely explained by theoretical analyses,numerical simulations,or field investigations.To study the mass-front velocity of dry granular flows influenced by the angle of the slope to the runout plane and particle size gradations we conducted model experiments that recorded the motion of rapid and long-runout rockslides or avalanches.Flume tests were conducted using slope angles of 25°,35°,45°,and 55° and three particle size gradations.The resulting mass-front motions consisted of three stages:acceleration,velocity maintenance,and deceleration.The existing methods of velocity prediction could not explain the slowing effect of the slope toe or the momentum-transfer steady velocity stage.When the slope angle increased from 25° to 55°,the mass-front velocities dropped significantly to between 44.4% and59.6% of the peak velocities and energy lossesincreased from 69.1% to 83.7% of the initial,respectively.The velocity maintenance stages occurred after the slope-toe and mass-front velocity fluctuations.During this stage,travel distances increased as the angles increased,but the average velocity was greatest at 45°.At a slope angle of 45°,as the median particle size increased,energy loss around the slope toe decreased,the efficiency of momentum transfer increased,and the distance of the velocity maintenance stage increased.We presented an improved average velocity formula for granular flow and a geometrical model of the energy along the flow line. 相似文献
16.
The distribution of saturated soft clay is greatly wide in China. The current main measures adopted to deal with soft soil foundations may lead to environmental pollution, even some engineering accidents may happen on soft soil foundations. In order to solve engineering problems of saturated soft soil foundations well, researches of mechanical properties of them are necessary. One of the most important mechanical characteristics of saturated soft clay is its cyclic accumulative deformation under cyclic loadings. For saturated soft clay, the cyclic accumulative deformation is similar to the creep behavior under static loadings. Therefore, the cyclic accumulative deformation is equivalent to the creep, the number of loading cycles is seen as the time, and this study develops a practical method for predicting the cyclic accumulative deformation of saturated soft clay with the creep theory. The method is a pseudostatic elasto-plastic finite element method implemented by ABAQUS software. A fitted equation between cyclic accumulative strain and number of loading cycles and the empirical relationship of parameters of fitted equation were established with a series of cyclic triaxial compression tests. Then with this empirical relationship of parameters, the method developed by this study was employed to predict the cyclic accumulative deformation under cyclic triaxial tension tests. Predicted results were in good agreement with test results, and the effectiveness of this method was thus validated for different stress states. The method was then applied in analyzing the cyclic accumulative deformation for soft soil foundation of a pile-supported wharf structure. 相似文献
17.
The soil moisture movement is an important carrier of material cycle and energy flow among the various geo-spheres in the cold regions. Thus, this research takes the north slope of Bayan Har Mountains in Qinghai-Tibet Plateau as a case study. The present study firstly investigates the change of permafrost moisture in different slope positions and depths. Based on this investigation, this article attempts to investigate the spatial variability of permafrost moisture and identifies the key influence factors in different terrain conditions. The method of classification and regression tree (CART) is adopted to identify the main controlling factors influencing the soil moisture movement. The relationships between soil moisture and environmental factors are revealed by the use of the method of canonical correspondence analysis (CCA). The results show that: 1) Due to the terrain slope and the freezing-thawing process, the horizontal flow weakens in the freezing period. The vertical migration of the soil moisture movement strengthens. It will lead to that the soil-moisture content in the up-slope is higher than that in the down-slope. The conclusion is contrary during the melting period. 2) Elevation, soil texture, soil temperature and vegetation coverage are the main environmental factors which affect the slope-permafrost soil-moisture. 3) Slope, elevation and vegetation coverage are the main factors that affect the slope-permafrost soil-moisture at the shallow depth of 0-20 cm. It is complex at the middle and lower depth. 相似文献
18.
《山地科学学报》2021,(4)
The landslide hazards occurring in the complex geological genesis accumulation body are usually controlled by the coupling action of many internal and external factors. Therefore, this paper takes the dam-front Danbo accumulation body landslide of Yangfanggou hydropower station on the Yalong River as the geological prototype, and discusses the process and mechanism of slope stability degradation under the combined action of rainfall and slope construction. Based on the detailed understanding of the basic characteristics of the accumulation body, the development characteristics of the landslide and the construction situation of the slope engineering, the study conducted correlation analysis between rainfall and landslide displacement, the physical and mechanical tests of all types of rocksoil masses, and the numerical simulation testing of seepage field variation of the landslide section. It is found that the special slope structure and material composition of the old landslide accumulation layer on the upper part of the Danbo accumulation body are the internal factors for the occurrence of thrust loadinduced landslide, and the construction of the slope engineering not only creates free space conditions for sliding, but also provides channels for the infiltration of rainfall into the slope after confluence, which is an external factor that caused the mechanical properties of the sliding zone soil to gradually weaken from the trailing edge to the leading edge. The geomechanical model of such landslide is that the active section of the trailing edge produces the "source of force", the transition section of the middle section affects the occurrence of sliding, and the anti-sliding section of the leading edge controls the occurrence of landslide hazards. The results of this research provide not only a useful supplement to the theory of landslide formation mechanisms but also a scientific basis for guiding the prevention and control of similar hazards. 相似文献
19.
The stability of soil-rock mixtures(SRMs) that widely distributed in slopes is of significant concern for slope safety evaluation and disaster prevention. The failure behavior of SRM slopes under surface loading conditions was investigated through a series of centrifuge model tests considering various volumetric gravel contents. The displacement field of the slope was determined with image-based displacement system to observe the deformation of the soil and the movement of the block during loading in the tests. The test results showed that the ultimate bearing capacity and the stiffness of SRM slopes increased evidently when the volumetric block content exceeded a threshold value. Moreover, there were more evident slips around the blocks in the SRM slope. The microscopic analysis of the block motion showed that the rotation of the blocks could aggravate the deformation localization to facilitate the development of the slip surface. The high correlation between the rotation of the key blocks and the slope failure indicated that the blocks became the dominant load-bearing medium that influenced the slope failure. The blocks in the sliding body formed a chain to bear the load and change the displacement distribution of the adjacent matrix sand through the block rotation. 相似文献
20.
Effect of clay content to the strength of gravel soil in the source region of debris flow 总被引：1，自引：0，他引：1
The production of runoff in the source area of a debris flow is the consequence of a reduction in soil strength. Gravel soil is widely distributed in the source region, and the influence of its clay content on soil strength is one of the important questions regarding the formation mechanism of debris flows. In this paper, the clay content in gravel soil is divided into groups of low clay content(1%, 2, 5%), moderate clay content(3.75%, 5.00%, 6.25%, 7.5%) and high clay content(10.0%, 12.5%, 15%). Tests of the unconsolidated undrained shear strength and consolidated drained shear strength were performed. The unconsolidated undrained shearing(UU) experiment simulates the rapid shear failure of loose gravel soil under the conditions of brief heavy rainfall. The consolidated drained shearing(CD) experiment simulates creep failure of consolidated sediment during extended rainfall. The pore water pressure first increased and then decreased as the clay content increased, and the increase in pore pressure was relatively high in the gravel soil sample when the clay content is in the range of 3.25-7.50%, and stress in the gravel soil is relatively low for a moderate clay content. Gravelly soils with a moderate clay content are moreprone to debris-flow initiation. This paper presents a mathematical formula for the maximum shear stress and clay content of gravel soil under two conditions. The key processes whereby the soil fails and triggers a debris flow—volume contraction of soil, expansion of clay soil, and rise of pore pressure―cause reductions in the soil friction force and enhancement of the water content in the clay particles, and subsurface erosion of soil reduces the soil viscosity, which eventually reduces the soil strength so that the soil loses its stability, liquefies and generates a debris flow. 相似文献