共查询到20条相似文献，搜索用时 46 毫秒
1.
海水池塘混合施肥养殖台湾红罗非鱼的鱼产力和负荷力 总被引：2，自引：0，他引：2
于１９９５年７—９月,在烟台市黄海水产集团公司第二养虾场,采用围隔实验法研究了海水池塘混合施肥养殖台湾红罗非鱼的鱼产力、负荷力和最适放养量。实验中每个围隔面积为 ５ｍ×５ｍ,各设 １台 ９０Ｗ的搅水机（４ ８００ｒ／ ｈ）。每日施肥基准为：鸡粪干物质, ２５ｋｇ／ｈａ：氮肥, Ｎ０．１５× １０－６;磷肥,Ｐ０．０１５× １０－６。结果表明,静水海水池塘混合施肥的鱼产力为０．７９ｇ／（ｍ２·ｄ）,池塘对台湾红罗非鱼的负荷力为１７９６．０ｋｇ／ｈａ,鱼（体重７０ｇ／ｉｎｄ）的最适放养量约为８０００ｉｎｄ／ｈａ。 相似文献
2.
紫彩血蛤的生物扰动对沉积物颗粒垂直分布的影响 总被引：3，自引：3，他引：0
以玻璃珠作为示踪颗粒,研究底栖双壳类软体动物紫彩血蛤对沉积物的扰动。室内实验的结果表明,在整个实验周期１０ｄ内,沉积物表层的示踪颗粒有４７％向下迁移,最大迁移深度１２ｃｍ,垂直迁移率为１．８０×１０－５·ｇ－１·ｃｍ－２·ｄ－１。沉积物１０ｃｍ深处的示踪颗粒分别有４５％和１５％向上和向下迁移,向上及向下迁移率分别为１．８９×１０－５·ｇ－１·ｃｍ－２·ｄ－１和０．６３×１０－５·ｇ－１·ｃｍ－２·ｄ－１ 相似文献
3.
黄、渤海几种海产无脊椎动物蛋白质与氨基酸含量分析 总被引：13，自引：1，他引：13
三疣梭子蟹（Ｐｏｒｔｕｎｕｓ ｔｒｉｔｕｂｅｒｃｕｌａｔｕｓ）、虾蛄（Ｓｑｕｉｌｌａｏｒａｔｏｒｉａ）、刺参（Ｓｔｉｃｈｏｐｕｓ ｊａｐｏｎｉｃｕｓ）、海地瓜（Ａｃａｕｄｉｎａｍｏｌｐａｄｉｏｉｄｅｓ）、脉红螺（Ｒａｐａｎａ ｖｅｎｏｓａ）、长竹蛏（Ｓｏｌｅｎｇｏｕｌｄｉｉ）、泥蚶（Ｔｅｇｉｌｌａｒｃａｇｒａｎｏｓａ）、菲律宾蛤仔（Ｒｕｄｉｔａｐｅｓｐｈｉｌｉｐｐｉｎａｒｕｍ）、紫贻贝（Ｍｙｔｉｌｕｓ ｅｄｕｌｉｓ）、长蛸（Ｏｃｔｏｐｕｓｖａｒｉａｂｉｌｉｓ）、马粪海胆（Ｈｅｍｉｃｅｎｔｒｏｔｕ… 相似文献
4.
金属离子对牙鲆仔鱼的毒性影响 总被引：4，自引：0，他引：4
本文用静水生物实验法进行了Ｚｎ、Ｃｕ、Ｐｂ、Ｃｄ金属离子对海洋底栖鱼类牙鲆（Ｐａｒａｌｉｃｈｔｈｙｓｏｌｉｖａｃｅｕｓ）仔鱼的成活影响研究。结果表明：Ｃｕ（２＋）、Ｃｄ（２＋）、Ｚｎ（２＋）、Ｐｂ（２＋）对牙鲆仔鱼２４ｈＬＣ（５０）分别为１．１４、１．５１、４．６８、５．８９ｍｇ／ｄｍ３．４８ｈＬＣ（５０）分别为０．１４、０．８３、０．９９、３．４７ｍｇ／ｄｍ３．７２ｈＬＣ（５０）分别为０．０６、０．３６、０．７１、０．９３ｍｇ／ｄｍ３．９６ｈＬＣ（５０）分别为０．０２、０．１４、０．４３、０．５３ｍｇ／ｄｍ３．Ｃｕ（２＋）对牙鲆仔鱼的毒性最大，Ｐｂ（２＋）的毒性最小．４种金属离子对仔鱼的毒性顺序依次为：Ｃｕ（２＋）＞Ｃｄ（２＋）＞Ｚｎ（２＋）＞Ｐｂ（２＋）． 相似文献
5.
6.
本文根据经济贝类污染物残留量调查结果，对辽宁沿岸海域贻贝、菲律宾蛤仔作为重金属、石油污染的生物指示种的可能性进行了初步研究和评价。应用ＰＯＬＹＤＩＶ统计技术对采自辽宁沿岸海域１４个站点样品中的重金属、石油含量进行了统计分析，结果表明辽宁沿岸海域各站点的贻贝、菲律宾蛤仔受Ｃｕ，Ｚｎ，Ｃｄ，Ｈｇ和石油污染与石油污染程度的分布和沿岸排放工业废水的分布及表层沉积物中的含量相一致。据此，贻贝和菲律宾蛤仔可作为监测Ｃｕ，ｍ，Ｃｄ，Ｈｇ和石油污染的生物指示种；可否作为Ｐｂ的生物指示种尚需进一步研究。 相似文献
7.
厌氧接触消化技术处理高浓度淀粉废水研究 总被引：1，自引：0，他引：1
实验采用厌氧接触消化技术，分别在中温（３２℃）和自然温度条件下处理淀粉厂的高浓度废水。结果表明，采用中温厌氧消化可取得较好的处理效果，原水不调ｐＨ（原水ｐＨ为４．０～４．９）直接进反应器，容积负荷最高达５．０６ｋｇＣＯＤｃｒ／ｍ３·ｄ，进水ＣＯＤｃｒ平均１１．６０４×１０３ｍｇ／ｌ，出水ＣＯＤｃｒ平均１．７７８×１０３ｍｇ／ｌ，ＣＯＤｃｒ去除率达８５．８％，出水ｐＨ提高到６．４～７．０。采用自然温度消化，当气温大于２４℃时，可取得较好的处理效果 相似文献
8.
虾蛄的人工养殖技术研究 总被引：7，自引：0，他引：7
１９９８年５月１日～７月１６日在浙江宁波大学水产苗种试验场进行了不同虾蛄种类,不同换水量,不同放苗规格、数量的养殖试验。结果表明：黑斑口虾蛄Ｏｒａｔｏｓｑｕｉｌａｋｅｍｐｉ比口虾蛄Ｏ．ｏｒａｔｏｒｉａ生长快、成活率高;水质条件较佳的塘,虾蛄生长迅速,平均每１０天体长增加１．４ｃｍ,产量达８０４．０ｋｇ／ｈｍ２。 相似文献
9.
本文在σ坐标下建立了一个半诊断计算及预报计算的数值模式，应用于台湾海峡夏季时三维海流计算。计算结果表明，当ｔ＝２．５ｄ时，密度场和速度场得到调整，即得到半诊断解，当ｔ＝４０ｄ以后，解已达到准稳定态；半诊断及预报计算的结果在定性上是与诊断计算结果一致。但它们在定量上有些变化，如表层台湾岛西岸附近的最大水平流速，在ｔ＝０时（诊断）为５９．１ｃｍ／ｓ，ｔ＝２．５ｄ时（半诊断）为６２．１ｃｍ／ｓ，ｔ＝３００ｄ时（预报）为６２．０ｃｍ／ｓ．此外，在半诊断及预报计算中，上升流也主嵰⑸诟＝ń兜龋魉偌忧浚段б灿兴┐蟆 相似文献
10.
通过淡水白鲳（ＣｏｌｏｓｓｏｍａｂｒａｃｈｙｐｏｍｕｍＣｕｖｉｅｒ）幼鱼（Ｌ＝２．９ｃｍ±０．０５ｃｍ）对氯化钠浓度（ｐＨ＝８．２１±０．０７）及碱度（ｐＨ＝８．８５±０．１８）的急性毒性试验。用概率单位法求得其２４、４８、９６ｈ的半致死浓度（ＬＣ５０）：氯化钠浓度分别为１２．０、１１．４、１０．４ｇ·Ｌ－１;碱度分别为８３．２５、５６．９９、４５．７０ｍｍｏｌ·Ｌ－１,并在此基础上进行盐碱混合正交试验,经统计分析得出碱度致死作用显著。在此条件下２４ｈＬＣ５０值时碱度与氯化钠浓度的关系为：Ａｌｋ（ｍｍｏｌ·Ｌ－１）＝２５６．２４－２４．６９Ｓａｌ（ｇ·Ｌ－１）。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.