首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
地震作用下立式储液罐罐壁“象足”变形仿真分析   总被引:1,自引:0,他引:1  
基于ANSYS软件建立了考虑液体晃动和罐底提离立式储液罐有限元模型,分别进行了水平地震和竖向地震作用下罐壁“象足”变形分析。分析表明:立式储液罐罐壁“象足”变形主要是由罐壁纵向压应力超过临界应力而产生的局部屈曲破坏,并非强度破坏。因罐底提离导致的罐底与基础反复撞击加大了作用在罐壁上的应力,使罐壁底部“象足”变形不断发展,最终导致罐壁撕裂。在完全相同地震加速度作用下,水平地震作用比竖向地震作用罐壁更早更容易进入屈曲状态,产生“象足”变形。  相似文献   

2.
地震作用下立式储液罐罐壁"象足"变形仿真分析   总被引:2,自引:0,他引:2  
基于ANSYS软件建立了考虑液体晃动和罐底提离立式储液罐有限元模型,分别进行了水平地震和竖向地震作用下罐壁"象足"变形分析.分析表明:立式储液罐罐壁"象足"变形主要是由罐壁纵向压应力超过临界应力而产生的局部屈曲破坏,并非强度破坏.因罐底提离导致的罐底与基础反复撞击加大了作用在罐壁上的应力,使罐壁底部"象足"变形不断发展,最终导致罐壁撕裂.在完全相同地震加速度作用下,水平地震作用比竖向地震作用罐壁更早更容易进入屈曲状态,产生"象足"变形.  相似文献   

3.
位移谐波激励下拱顶锚固储罐的动力屈曲研究   总被引:1,自引:1,他引:0  
地震下储罐罐壁发生屈曲是其主要的震害形式,研究储罐的动力屈曲特性尤为重要.以位移简谐波为水平激励,运用ADINA有限元软件对高径比分别为0.82、1.24和1.85的3种拱顶锚固储罐进行动力屈曲分析.根据Budiansky-Roth动力屈曲准则,通过谐波位移幅值对应的加速度峰值PGA和储罐位移响应,绘制特征节点的"伪平衡路径"轨迹,以确定临界加速度峰值,判断储罐动力屈曲.3种储罐模型在位移谐波激励下均为弹性屈曲.通过动力屈曲分析得出结论:储罐屈服的位置随高径比的不同有所不同,屈服多发生在径向变形最大处,罐壁内外面的塑性总应变值和屈服应力值大小不同等.最后以储罐模型B为例,将以"伪平衡路径"轨迹确定的临界应力与规范公式的计算结果进行了比较.  相似文献   

4.
地震作用下大型储液罐的安全问题日益引起重视。基于ANSYS软件建立储罐液体耦合有限元模型,考虑罐底非线性接触效应,以El-Centro南北向和竖直向记录地震波为输入,研究水平激励以及水平和竖向同时激励两种工况下储罐的动力响应。研究结果表明,两种工况下靠近罐底1.2m处均发生了"象足"变形,竖向激励下水平相对位移增加了14%。竖向激励使得罐壁环向应力和轴向压应力均有不同程度的增加。竖向地震激励对液面的竖向晃动影响较小。储液罐底板在地震作用下发生了竖向提离和永久滑移,竖向激励时增长幅度均在10%左右。同时罐体基底剪力在竖向地震作用下也有所增大。储罐抗震设计时应考虑竖向地震分量的影响,研究结论可为立式储罐的抗震设计提供一定的参考和依据。  相似文献   

5.
位移谐波激励下拱顶锚固储罐的动力响应分析   总被引:1,自引:1,他引:0  
地震中拱顶锚固储罐的破坏将造成严重的后果,研究其地震作用下的动力响应特性具有一定工程意义。以位移简谐波为水平激励,运用AD INA有限元软件对一座3 000m3的拱顶锚固储罐模型进行动力数值模拟,系统分析了储罐内液面晃动波高、动水压力极值、罐壁应力、拱顶应力、拱顶位移等动力响应结果,将以位移谐波激励和以加速度谐波激励的储罐动力响应结果进行比较。分析表明,位移谐波激励下拱顶锚固储罐的液面晃动波高受场地影响较大;储罐应力分布具有一定规律性;采用位移谐波激励时其应力、位移和动水压力等较采用加速度谐波激励时大,液体晃动波高较小。  相似文献   

6.
基于概率估计方法的立式储罐地震易损性研究   总被引:1,自引:1,他引:0  
结合储罐的震害资料和震害特点,提出了基于概率估计方法的立式储罐地震易损性研究.考虑了结构的随机性及荷载作用的随机性,给出了各随机变量的概率分布模型及给定烈度下地震发生的概率.从可靠度指标的几何意义入手,提出了储罐的地震易损性计算方法.通过2×103m3和5×104m32种高矮罐的地震易损性研究,结果表明:通过概率方法和绘制地震易损性曲线的方式,更能直观的给出储罐各失效模式的地震易损性.储罐的地震易损性与地震烈度、高径比的关系很大,地震易损性随着地震烈度的增大逐渐增大;与2×103m3储罐相比,5×104m3储罐各失效模式地震易损性明显较小;从多种失效模式进行储罐地震易损性研究更具有科学性.  相似文献   

7.
为了研究桩土、隔震层与罐体相互作用对15×104m3隔震储罐地震响应的影响,桩与隔震层采用弹簧-阻尼单元,罐体采用壳单元,流体采用势流体单元,基于ADINA建立数值仿真分析模型,在8度E1 Centro地震动激励下,应用Newmark数值积分方法进行地震响应分析.结果表明:隔震储罐基底剪力和基底弯矩相对于非隔震储罐明显降低,储罐罐壁加速度沿罐壁高度方向近乎平动,但对波高的控制效果不明显;除罐壁顶部外,动液压力明显降低;隔震后,罐壁有效应力和环向应力减震效应明显,对轴向应力和径向应力影响较小,建议从安全角度考虑,储罐非隔震设计时不考虑桩土作用,隔震设计时考虑桩土对罐体的影响.  相似文献   

8.
立式浮顶储罐在强震作用下会发生罐壁屈曲、卡顶、浮顶下沉等震害。为降低储罐地震响应,以1 000 m3储罐为原型,按1:5的几何相似比设计缩尺模型,并以隔震周期为0.5 s进行并联隔震装置设计,给出其力学本构关系。采用模拟地震振动台试验方法,选取四种不同频谱特性的地震动对模型罐进行地震响应分析,结果表明:隔震层顶部加速度卓越频率有所降低,周期延长;隔震后储罐加速度、层间位移及动应力地震响应明显降低,但晃动波高有所放大;三向地震激励与单向地震激励相比,加速度地震响应明显放大,对晃动波高影响较小。建议储罐抗震减震设计时应考虑三向地震作用。  相似文献   

9.
为考虑土与结构相互作用(SSI)对15×104m3大型立式储罐基础隔震效应的影响,采用弹簧-阻尼系统模拟地基土和隔震层,罐壁及底板采用壳单元,流体采用势流体单元,利用ADINA建立15×104m3储罐有限元模型,在峰值加速度0.2g El Centro波地震激励下,应用Newmark数值积分方法进行地震响应分析,结果表明:考虑SSI效应时,非隔震储罐的地震响应有所减小,而基础隔震时地震响应有放大效应。储罐抗震减震设计时,中软地基土上储罐从结构设计安全角度来说需要考虑土与结构的相互作用。  相似文献   

10.
立式储罐与地基相互作用地震反应分析   总被引:2,自引:1,他引:1  
在考虑地基与储罐相互作用的情况下,采用有限元法对储罐住水平地震荷载作用下的反应进行了计算。推导了系统刚度矩阵及质量矩阵的计算过程。通过对四种场地条件下的地震响应分析,得出了储罐各种参数对地震反应的影响。分析表明:不同的地震激励对储罐系统的反应是不同的;地基刚度对系统的动力响应的影响也很大:即地基越“柔”,基底弯矩、罐壁轴向应力越小,但环向应力和底板变形却在增加。  相似文献   

11.
12.
13.
《国际泥沙研究》2014,(4):F0003-F0003
  相似文献   

14.
《国际泥沙研究》2014,(2):F0003-F0003
  相似文献   

15.
《国际泥沙研究》2014,(3):F0003-F0003
  相似文献   

16.
17.
The partitioning of rain water into throughfall, stemflow and interception loss when passing through plant canopies depends on properties of the respective plant species, such as leaf area and branch angles. In heterogeneous vegetation, such as tropical forest or polycultural systems, the presence of different plant species may consequently result in a mosaic of situations with respect to quantity and quality of water inputs into the soil. As these processes influence not only the water availability for the plants, but also water infiltration and nutrient leaching, the understanding of plant effects on the repartitioning of rain water may help in the optimization of land use systems and management practices. We measured throughfall and stemflow in a perennial polyculture (multi‐strata agroforestry), monocultures of peach palm (Bactris gasipaes) for fruit and for palmito, a monoculture of cupuaçu (Theobroma grandiflorum), spontaneous fallow and primary forest during one year in central Amazonia, Brazil. The effect on rain water partitioning was measured separately for four useful tree species in the polyculture and for two tree species in the primary forest. Throughfall at two stem distances, and stemflow, differed significantly between tree species, resulting in pronounced spatial patterns of water input into the soil in the polyculture system. For two tree species, peach palm for fruit (Bactris gasipaes) and Brazil nut trees (Bertholletia excelsa), the water input into the soil near the stem was significantly higher than the open‐area rainfall. This could lead to increased nutrient leaching when fertilizer is applied close to the stem of these trees. In the primary forest, such spatial patterns could also be detected, with significantly higher water input near a palm (Oenocarpus bacaba) than near a dicotyledonous tree species (Eschweilera sp.). Interception losses were 6·4% in the polyculture, 13·9 and 12·3% in the peach palm monocultures for fruit and for palmito, respectively, 0·5% in the cupuaçu monoculture and 3·1% in the fallow. With more than 20% of the open‐area rainfall, the highest stemflow contributions to the water input into the soil were measured in the palm monocultures and in the fallow. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

18.
A procedure for short-term rainfall forecasting in real-time is developed and a study of the role of sampling on forecast ability is conducted. Ground level rainfall fields are forecasted using a stochastic space-time rainfall model in state-space form. Updating of the rainfall field in real-time is accomplished using a distributed parameter Kalman filter to optimally combine measurement information and forecast model estimates. The influence of sampling density on forecast accuracy is evaluated using a series of a simulated rainfall events generated with the same stochastic rainfall model. Sampling was conducted at five different network spatial densities. The results quantify the influence of sampling network density on real-time rainfall field forecasting. Statistical analyses of the rainfall field residuals illustrate improvement in one hour lead time forecasts at higher measurement densities.  相似文献   

19.
Red tide, a recurrent phenomenon has become conspicuous in several Kashmir lake ecosystems since 1991. The responsible organism (Euglena pedunculata), a rare flagellate rediscovered in the Kashmir Himalaya (Khan 1993) caused first and unprecedented red tide outbreak, constituting a maximum of 96% of resident numerical phytoplankton density in Dal Lake. At present, conflicting hypotheses exist on the generation of causal assemblage(s) imparting redness to waters: Jeeji Bai (1991) linked its origin to acid precipitation – a fallout of burning oil‐fields during the Gulf War – whilst Khan (1993) holds local factor(s) responsible. Field/experimental studies support the latter contention that the influx of untreated sewage, in unison with warm temperatures, high levels of PhAR, iron and interruption to hydrological flow‐pattern together with absence/or reduction in grazing activity created conducive environmental milieu for red tide outbreak. Dal Lake “red tide” drifted the bloom‐inoculum to other waters, including Lake Wular, where additional ecological niches were carved out, threatening the aesthetic value and biological diversity of Kashmir lakes. Ecological monitoring indicates frequent seasonal red tide occurrence in Dal Lake (including summer‐autumn event of 1998) which testifies its unabated eutrophication status. Further studies are needed on ecological adaptability and biogeographic distribution of this rare and unique red tide‐causing flagellate.  相似文献   

20.
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号