共查询到20条相似文献，搜索用时 31 毫秒
1.
由弹性波纵横波速比计算得到的泊松比,在利用地震波反演地下结构和物质组成时,可以提供比单纯地利用纵波或者横波波速更强的约束. 为了研究不同岩石中泊松比及其各向异性随围压的变化,选取19块典型的岩石样品,在不同围压下沿相互正交的3个方向同时测量纵、横波速度,并通过计算得到了泊松比及其各向异性. 结果表明,在大部分样品中泊松比各向异性与纵波速度各向异性有一定的相关性,但在有的样品中泊松比各向异性与纵波速度各向异性没有明显的关系,甚至表现出完全相反的变化规律. 由于泊松比也表现出很强的各向异性,在排除微裂隙的影响后有的仍可以达到30髎以上,在利用实际地震波传播数据通过泊松比反演地下物质结构时必须考虑其各向异性的影响. 相似文献
2.
3.
First-arrival traveltimes from a multi-offset vertical seismic profile (VSP) were used to estimate velocity anisotropy in the presence of a vertical velocity gradient. A numerical model consisting of two layers with vertical velocity gradients of 3.1 and 1.2 s−1, respectively, and global anisotropy parameters of =0.12±0.02 and δ=0.30±0.06 yielded first-arrival traveltimes that matched the observed traveltimes well. Shallow receivers were found to be crucial for constraining the vertical velocity field and for determining the parameters of anisotropy at depth. 相似文献
4.
JOS M. CARCIONE 《Geophysical Prospecting》1992,40(7):761-783
When a seismic signal propagates through a finely layered medium, there is anisotropy if the wavelengths are long enough compared to the layer thicknesses. It is well known that in this situation, the medium is equivalent to a transversely isotropic material. In addition to anisotropy, the layers may show intrinsic anelastic behaviour. Under these circumstances, the layered medium exhibits Q anisotropy and anisotropic velocity dispersion. The present work investigates the anelastic effect in the long-wavelength approximation. Backus's theory and the standard linear solid rheology are used as models to obtain the directional properties of anelasticity corresponding to the quasi-compressional mode qP, the quasi-shear mode qSV, and the pure shear mode SH, respectively. The medium is described by a complex and frequency-dependent stiffness matrix. The complex and phase velocities for homogeneous viscoelastic waves are calculated from the Christoffel equation, while the wave-fronts (energy velocities) and quality factor surfaces are obtained from energy considerations by invoking Poynting's theorem. We consider two-constituent stationary layered media, and study the wave characteristics for different material compositions and proportions. Analyses on sequences of sandstone-limestone and shale-limestone with different degrees of anisotropy indicate that the quality factors of the shear modes are more anisotropic than the corresponding phase velocities, cusps of the qSV mode are more pronounced for low frequencies and midrange proportions, and in general, attenuation is higher in the direction perpendicular to layering or close to it, provided that the material with lower velocity is the more dissipative. A numerical simulation experiment verifies the attenuation properties of finely layered media through comparison of elastic and anelastic snapshots. 相似文献
5.
对华北地区韧性剪切带几种代表上、中、下地壳深度的糜棱岩及其围岩在高温高压条件下进行纵波速度测定及各向异性研究．对实验样品的纵波速度测定得到以下结果：１．沿糜棱岩面理方向的纵波速度大于与面理垂直方向的纵波速度，差值为０．１５-０．３０ｋｍ／ｓ，各向异性为３％-５％；２．糜棱岩的纵波速度低于其围岩的纵波速度，差值为０．１０-０．４５ｋｍ／ｓ；３．中地壳角闪岩相糜棱岩的纵波速度各向异性高于上地壳绿片岩相糜棱岩和下地壳麻粒岩相糜棱岩的各向异性；４．地震波速各向异性与糜棱岩矿物优选定向有关． 相似文献
6.
7.
从西藏南部的定日、嘎拉至青海铜铁山的天然地震探测剖面，实际路线长约２０００ｋｍ，布设了约１１０台便携地震仪，记录了数百次远震和近震事件，采用多种方法进行了资料处理与解释．依据ＳＫＳ，ＰＫＳ，ｐｓ等横波分裂特征计算的青藏高原中部上地幔的地震各向异性表明：研究区各构造单元内的地震各向异性有明显变化，发现上地幔各向异性快速波的偏振方向与造山带的走向不完全一致．在雅江缝合线、崩错－嘉黎、唐古拉山口、昆仑山口几条断裂带处南、北各向异性出现显著的差异，而金沙江缝合线和班公－怒江缝合线的南、北则没有明显的各向异性变化．由Ｐ波走时残差，利用层析技术反演了４００ｋｍ深度内的速度图像，可以看出近地表１００ｋｍ范围内速度的不均匀变化与地表划分的构造单元很吻合，进一步佐证了青藏高原是由不同时期的微板块拼合而成的认识．在青藏高原中部１５０ｋｍ深度以下发现了多处低速区．在金沙江缝合带下方约２００ｋｍ深度处有一长２５０ｋｍ以上、延伸１５０ｋｍ的低速体，推测可能是一地幔柱．利用ＰＳ转换波划分的界面，显示出青藏高原北部具有低速层和高速层交替出现的地壳结构． 相似文献
8.
9.
C.M. Sayers 《Geophysical Prospecting》1995,43(4):541-568
Results from walkaway VSP and shale laboratory experiments show that shale anisotropy can be significantly anelliptic. Heterogeneity and anellipticity both lead to non-hyperbolic moveout curves and the resulting ambiguity in velocity analysis is investigated for the case of a factorizable anisotropic medium with a linear dependence of velocity on depth. More information can be obtained if there are several reflectors. The method of Dellinger et al. for anisotropic velocity analysis in layered transversely isotropic media is examined and is shown to be restricted to media having relatively small anellipticity. A new scheme, based on an expansion of the inverse-squared group velocity in spherical harmonics, is presented. This scheme can be used for larger anellipticity, and is applicable for horizontal layers having monoclinic symmetry with the symmetry plane parallel to the layers. The method is applied to invert the results of anisotropic ray tracing on a model Sand/shale sequence. For transversely isotropic media with small anisotropy, the scheme reduces to the method of Byun et al. and Byun and Corrigan. The expansion in spherical harmonics allows the P-phase slowness surface of each layer to be determined in analytic form from the layer parameters obtained by inversion without the need to assume that the anisotropy is weak. 相似文献
10.
M. S. SAMS M. H. WORTHINGTON M. S. KING M. SHAMS KHANSHIR 《Geophysical Prospecting》1993,41(2):189-206
P-wave velocity anisotropy determined from a cross-hole survey at the Imperial College borehole test site compares favourably with that measured in the laboratory on core from the holes. The holes penetrate a layered sequence of sandstones, shales and carbonates of the Namurian Upper Limestone Group. The Laboratory measurements of the vertical and horizontal velocities of core samples indicate that the shales exhibit P-wave anisotropies of over 20% but that the sandstones and limestones are only slightly anisotropic. These discrete measurements have been used in combination with wireline data to produce a log of P-wave anisotropy. Including the anisotropic information vastly improves the match between observed and synthetic traveltimes from the cross-hole data set. This implies that there is little frequency dependence of intrinsic P-wave anisotropy. Inversion of the cross-hole traveltimes highlights the need for good angular coverage in order to resolve the anisotropy parameters. The observed P-wave anisotropy of the field data is due to the combined effect of sedimentary layering and the intrinsic anisotropy of the rocks. The intrinsic anisotropy is found to be the dominant factor. 相似文献
11.
横向各向同性介质中地震波速度分析及其意义 总被引：2，自引：4，他引：2
在地震学有关领域中，地下介质的薄互层特性与裂隙的定向人布在长波长假设下会产生等效的地震各向异性特性，地震波速度随传播方向和深度发生的变化引起了广大地球物理工作者的广泛兴趣，因为速度拾取的正确与否，会直接影响到油气勘探中动校、偏移、ＡＶＯ和时深转换的结果。本文着重讨论了传统速度分析的局限性，分析了薄互层引起的横向各向同性介质中速度分析的现状和结果，实例讨论了各向异性效应对偏移处理的影响，表明各向异性 相似文献
12.
在实验室中研究了蛇纹岩和角闪岩样品在不同温压条件下的纵、横波速度和Q值．这两种岩样对应的主要组成矿物叶蛇纹石和普通角闪石都具有很强的晶格优选方位（LPO）．随着围压的增加,波速和Q值均增大,但是在相互正交的三个方向上（垂直或平行于层理面及线理方向）增大的速度并不相同,这与微裂隙的逐渐闭合密切相关．在600MPa的围压下升高温度直到600℃以上,由于微裂隙的热扩张受到约束,波速和Q值下降幅度很小．观测到的波速和Q值的各向异性具有不同的机理,波速各向异性主要与定向分布的微裂隙和主要矿物的LPO等构造因素有关;高围压下纵波Q值各向异性与速度各向异性正好相反,可能是由于形成层理面的定向排列的平板状矿物晶体沿不同方向边界之间接触程度不同造成的． 相似文献
13.
深部岩石的弹性波各向异性是人们了解地壳深部构造特征,分析其成因,探讨其动力学意义的重要岩石物理参数。实验结果表明由矿物晶格定向分布(LPO)所引起的地壳岩石平均各向异性强度通常不超过5%,远不足以解释在青藏高原地壳中所观测到的弹性波各向异性之强度。模拟结果显示,熔体的定向分布(MPO)能够引起强烈的弹性波各向异性。例如,当熔体的形态因子(α)值介于0.1～0.5之间,熔融程度为5%～10%时,由定向分布的酸性熔体囊所产生的各向异性强度可以达到2%～10%(P波)、2.2～40%(S波)。众多研究资料显示,青藏高原—川滇西部具有加厚的中、上地壳和高地热梯度,低度部分熔融作用在其深部地壳中广泛存在。低度熔体在构造应力作用下的定向分布可能是造成该地区深部地壳存在异常强的各向异性层的重要原因。这暗示目前在青藏高原—川滇西部探测到的异常强的区域性各向异性层是具有部分熔融成因的强烈构造变形带。该构造变形带具有潜在的"解耦"功能,并作为地壳浅部刚性层(块体)的底界协调着块体与其下伏地壳或岩石圈地幔的差异运动。 相似文献
14.
Based on a large set of arrival times of the Pg phase reported by local and regional stations, we estimate azimuthal anisotropy of the Pg-wave velocity in focal volumes of the upper crust in NW Croatia. The method is based on analyses of the azimuthal dependence
of ratios of cumulative differences of arrival times and travel paths between foci of earthquake pairs, computed for rays
propagating within narrow azimuthal windows. The results clearly indicate the presence of anisotropy of 3.3% with the direction
of fast velocity (approximately NNE-SSW) coinciding with the direction of the maximum tectonic pressure as revealed by 23
available focal mechanisms and previous geological investigations. Although a large part of observed anisotropy can be explained
assuming that focal volumes are pervaded by a system of vertical extensive-dilatancy anisotropy (EDA) cracks aligned under
the influence of local tectonic stress field, there is indication that — to a smaller extent — some role was also played by
alignment of structural features in the region. 相似文献
15.
16.
Tilted transversely isotropic formations cause serious imaging distortions in active tectonic areas (e.g., fold‐and‐thrust belts) and in subsalt exploration. Here, we introduce a methodology for P‐wave prestack depth imaging in tilted transversely isotropic media that properly accounts for the tilt of the symmetry axis as well as for spatial velocity variations. For purposes of migration velocity analysis, the model is divided into blocks with constant values of the anisotropy parameters ε and δ and linearly varying symmetry‐direction velocity VP0 controlled by the vertical (kz) and lateral (kx) gradients. Since determination of tilt from P‐wave data is generally unstable, the symmetry axis is kept orthogonal to the reflectors in all trial velocity models. It is also assumed that the velocity VP0 is either known at the top of each block or remains continuous in the vertical direction. The velocity analysis algorithm estimates the velocity gradients kz and kx and the anisotropy parameters ε and δ in the layer‐stripping mode using a generalized version of the method introduced by Sarkar and Tsvankin for factorized transverse isotropy with a vertical symmetry axis. Synthetic tests for several models typical in exploration (a syncline, uptilted shale layers near a salt dome and a bending shale layer) confirm that if the symmetry‐axis direction is fixed and VP0 is known, the parameters kz, kx, ε and δ can be resolved from reflection data. It should be emphasized that estimation of ε in tilted transversely isotropic media requires using nonhyperbolic moveout for long offsets reaching at least twice the reflector depth. We also demonstrate that application of processing algorithms designed for a vertical symmetry axis to data from tilted transversely isotropic media may lead to significant misfocusing of reflectors and errors in parameter estimation, even when the tilt is moderate (30°). The ability of our velocity analysis algorithm to separate the anisotropy parameters from the velocity gradients can be also used in lithology discrimination and geologic interpretation of seismic data in complex areas. 相似文献
17.
JOHN C. ROBINSON 《Geophysical Prospecting》1970,18(3):352-363
Three common expressions for the normal moveout of recorded seismic events are investigated by numerical simulation procedures for accuracy in predicting the root-mean-squared (RMS) or mean, as the case may be, subsurface velocity function from seismic data. The principal investigation, for which detailed error curves are shown, was derived for a stochastic subsurface model composed of strata with thicknesses ranging up to 91.4 m (300 ft) and boundary velocity contrasts ranging up to 45.7 m/sec (150 ft/sec); there was a 95 percent chance of velocity increase with increased depth. The effects of changes in the basic statistical subsurface model are discussed. The results appear to confirm the judiciousness of the choices of to and (x/z') as plotting parameters to be used with the respective percent errors in the three expressions, where are, respectively, the zero-offset arrival time of, the offset distance of, and the mean-squared velocity encountered by a seismic ray. Out of the three normal-moveout expressions examined, the “straight-raypath” expression with the RMS velocity substituted as its velocity term proved to be the most accurate in the determination of velocities. 相似文献
18.
BRUCE J. VERWEST 《Geophysical Prospecting》1989,37(2):149-166
The study of wave propagation in media with elliptical velocity anisotropy shows that seismic energy is focused according to the horizontal component of the velocity field while the vertical component controls the time-to-depth relation. This implies that the vertical component cannot be determined from surface seismic velocity analysis but must be obtained using borehole or regional geological information. Both components of the velocity field are required to produce a correctly focused depth image. A paraxial wave equation is developed for elliptical anisotropic wave propagation which can be used for modelling or migration. This equation is then transformed by a change of variable to a second paraxial equation which only depends on one effective velocity field. A complete anisotropic depth migration using this transformed equation involves an imaging step followed by a depth stretching operation. This allows an approximate separation or splitting of the focusing and depth conversion steps of depth migration allowing a different velocity model to be used for each step. This split anisotropic depth migration produces a more accurate result than that obtained by a time migration using the horizontal velocity field followed by an image-ray depth conversion using the vertical velocity field. The results are also more accurate than isotropic depth migration and yield accurate imaging in depth as long as the lateral variations in the anisotropy are slow. 相似文献
19.
本文搜集江苏台网1982年-1987年2月间发生在江苏及其邻近地区103次地震的1047个P_n数据,经过静校正和质量分类,重新计算了震中距.选择灌云台为参考台,对一次地震的P_n数据,其它台均减去参考台的数据,成功地消除了与震源参数不确定有关的误差.处理中采用质量加权,获得了上地幔平均速度、大部分台P_n残差以及不同方位上P_n视速度估计值. 按Backus给出的波速各向异性的公式,求出江苏地区P_n速度与方位之间有2％左右的速度各向异性,最大方向和对称方向近南北,最小方向为北东东.推断其成因是由于白垩纪至第三纪期间壳下岩石圈北南向流变引起橄榄石晶体从优定向的结果.这为苏北盆地及下扬子碳酸盐岩地区地质构造形成发展动力学的建立提供了有利的深部依据. 相似文献
20.
W.J. VETTER 《Geophysical Prospecting》1987,35(6):700-717
Since the important contributions of Dürbaum and Dix, 30 years ago, velocity profile estimation procedures on horizontally layered and vertically heterogeneous media from seismic probing data have been based largely on hyperbolic moveout models and RMS and stacking velocity concepts. Re-examination of the fundamentals reveals that quantitative velocity heterogeneity and canonical valocity profiles have been implicit factors for moveout modelling and for profile inversion in the use of the Dix procedure. Heterogeneity h is the ratio (and vRMS the geometric or harmonic mean) of the path-average and time-average velocities for a raypath or, in a more restricted sense, for the normal ray belonging to a velocity profile. The canonical profile for a given velocity profile or profile segment is a moveout-equivalent monotonically increasing ramp-like profile. The ramp or constant gradient in depth is the simplest velocity profile approximator which can explicitly accommodate velocity heterogeneity. A ramp model structure is detailed which facilitates moveout simulation and model parameter estimation, and the parametric effects are explored. The horizontal offset range is quantified for which this model can give good moveout approximations. 相似文献