共查询到20条相似文献，搜索用时 31 毫秒
1.
The dependence of shear‐wave splitting in fractured reservoirs on the properties of the filling fluid may provide a useful attribute for identifying reservoir fluids. If the direction of wave propagation is not perpendicular or parallel to the plane of fracturing, the wave polarized in the plane perpendicular to the fractures is a quasi‐shear mode, and therefore the shear‐wave splitting will be sensitive to the fluid bulk modulus. The magnitude of this sensitivity depends upon the extent to which fluid pressure can equilibrate between pores and fractures during the period of the deformation. In this paper, we use the anisotropic Gassmann equations and existing formulations for the excess compliance due to fracturing to estimate the splitting of vertically propagating shear waves as a function of the fluid modulus for a porous medium with a single set of dipping fractures and with two conjugate fracture sets, dipping with opposite dips to the vertical. This is achieved using two alternative approaches. In the first approach, it is assumed that the deformation taking place is quasi‐static: that is, the frequency of the elastic disturbance is low enough to allow enough time for fluid to flow between both the fractures and the pore space throughout the medium. In the second approach, we assume that the frequency is low enough to allow fluid flow between a fracture set and the surrounding pore space, but high enough so that there is not enough time during the period of the elastic disturbance for fluid flow between different fracture sets to occur. It is found that the second approach yields a much stronger dependence of shear‐wave splitting on the fluid modulus than the first approach. This is a consequence of the fact that at higher wave frequencies there is not enough time for fluid pressure to equilibrate and therefore the elastic properties of the fluid have a greater effect on the magnitude of the shear‐wave splitting. 相似文献
2.
Mark Chapman Jeremy Sothcott Angus Ian Best Xiang‐Yang Li 《Geophysical Prospecting》2014,62(6):1238-1252
Ultrasonic (500 kHz) P‐ and S‐wave velocity and attenuation anisotropy were measured in the laboratory on synthetic, octagonal‐shaped, silica‐cemented sandstone samples with aligned penny‐shaped voids as a function of pore fluid viscosity. One control (blank) sample was manufactured without fractures, another sample with a known fracture density (measured from X‐ray CT images). Velocity and attenuation were measured in four directions relative to the bedding fabric (introduced during packing of successive layers of sand grains during sample construction) and the coincident penny‐shaped voids (fractures). Both samples were measured when saturated with air, water (viscosity 1 cP) and glycerin (100 cP) to reveal poro‐visco‐elastic effects on velocity and attenuation, and their anisotropy. The blank sample was used to estimate the background anisotropy of the host rock in the fractured sample; the bedding fabric was found to show transverse isotropy with shear wave splitting (SWS) of 1.45 ± 1.18% (i.e. for S‐wave propagation along the bedding planes). In the fractured rock, maximum velocity and minimum attenuation of P‐waves was seen at 90° to the fracture normal. After correction for the background anisotropy, the fractured sample velocity anisotropy was expressed in terms of Thomsen's weak anisotropy parameters ε, γ & δ. A theory of frequency‐dependent seismic anisotropy in porous, fractured, media was able to predict the observed effect of viscosity and bulk modulus on ε and δ in water‐ and glycerin‐saturated samples, and the higher ε and δ values in air‐saturated samples. Theoretical predictions of fluid independent γ are also in agreement with the laboratory observations. We also observed the predicted polarisation cross‐over in shear‐wave splitting for wave propagation at 45° to the fracture normal as fluid viscosity and bulk modulus increases. 相似文献
3.
Azimuthal anisotropy in rocks can result from the presence of one or more sets of partially aligned fractures with orientations determined by the stress history of the rock. The symmetry of a rock with horizontal bedding that contains two or more non-orthogonal sets of vertical fractures may be approximated as monoclinic with a horizontal plane of mirror symmetry. For offsets that are small compared with the depth of the reflector, the azimuthal variation in P-wave AVO gradient for such a medium varies with azimuth as where φ is the azimuth measured with respect to the fast polarization direction for a vertically polarized shear wave. φ 2 depends on both the normal compliance B N and the shear compliance B T of the fractures and may differ from zero if B N B T varies significantly between fracture sets. If B N B T is the same for all fractures, and the principal axes of the azimuthal variation in P-wave AVO for fixed offset are determined by the polarization directions of a vertically propagating shear wave. At larger offsets, terms in and are required to describe the azimuthal variation in AVO accurately. φ 4 and φ 6 also depend on B N B T . For gas-filled open fractures but a lower value of B N B T may result from the presence of a fluid with non-zero bulk modulus. 相似文献
4.
Philip Tillotson Angus Ian Best Jeremy Sothcott Clive McCann Wang Shangxu Xiang‐Yang Li 《Geophysical Prospecting》2011,59(1):111-119
P‐ and S‐wave velocity and attenuation coefficients (accurate to ±0.3% and ±0.2 dB/cm, respectively) were measured in synthetic porous rocks with aligned, penny‐shaped fractures using the laboratory ultrasonic pulse‐echo method. Shear‐wave splitting was observed by rotating the S‐wave transducer and noting the maximum and minimum velocities relative to the fracture direction. A block of synthetic porous rock of fracture density 0.0201 ± 0.0068 and fracture size 3.6 ± 0.38 mm (measured from image analysis of X‐ray CT scans) was sub‐sampled into three 20–30 mm long, 50 mm diameter core plugs oriented at 0°, 45° and 90° to the fracture normal (transversely isotropic symmetry axis). Full waveform data were collected over the frequency range 500–1000 kHz for both water and glycerin saturated cores to observe the effect of pore fluid viscosity at 1 cP and 100 cP, respectively. The shear‐wave splitting observed in the 90° core was 2.15 ± 0.02% for water saturated and 2.39 ± 0.02% for glycerin saturated, in agreement with the theory that suggests that the percentage splitting should be 100 times the fracture density and independent of the saturating fluid. In the 45° core, by contrast, splitting was 0.00 ± 0.02% for water saturation and ?0.77 ± 0.02% for glycerin saturation. This dependence on fracture orientation and pore fluid viscosity is consistent with the poro‐visco‐elastic theory for aligned, meso‐scale fractures in porous rocks. The results suggest the possible use of shear‐ or converted‐wave data to discriminate between fluids on the basis of viscosity variations. 相似文献
5.
We have implemented a 3D finite‐difference scheme to simulate wave propagation in arbitrary anisotropic media. The anisotropic media up to orthorhombic symmetry were modelled using a standard staggered grid scheme and beyond (monoclinic and triclinic) using a rotated staggered grid scheme. The rationale of not using rotated staggered grid for all types of anisotropic media is that the rotated staggered grid schemes are more expensive than standard staggered grid schemes. For a 1D azimuthally anistropic medium, we show a comparison between the seismic data generated by our finite‐difference code and by the reflectivity algorithm; they are in excellent agreement. We conducted a study on zero‐offset shear‐wave splitting using the finite‐difference modelling algorithm using the rotated staggered grid scheme. Our S‐wave splitting study is mainly focused on fractured media. On the scale of seismic wavelenghts, small aligned fractures behave as an equivalent anisotropic medium. We computed the equivalent elastic properties of the fractures and the background in which the fractures were embedded, using low‐frequency equivalent media theories. Wave propagation was simulated for both rotationally invariant and corrugated fractures embedded in an isotropic background for one, or more than one, set of fluid‐filled and dry fractures. S‐wave splitting was studied for dipping fractures, two vertical non‐orthogonal fractures and corrugated fractures. Our modelling results confirm that S‐wave splitting can reveal the fracture infill in the case of dipping fractures. S‐wave splitting has the potential to reveal the angle between the two vertical fractures. We also notice that in the case of vertical corrugated fractures, S‐wave splitting is sensitive to the fracture infill. 相似文献
6.
In fractured reservoirs, seismic wave velocity and amplitude depend on frequency and incidence angle. Frequency dependence is believed to be principally caused by the wave‐induced flow of pore fluid at the mesoscopic scale. In recent years, two particular phenomena, i.e., patchy saturation and flow between fractures and pores, have been identified as significant mechanisms of wave‐induced flow. However, these two phenomena are studied separately. Recently, a unified model has been proposed for a porous rock with a set of aligned fractures, with pores and fractures filled with two different fluids. Existing models treat waves propagating perpendicular to the fractures. In this paper, we extend the model to all propagation angles by assuming that the flow direction is perpendicular to the layering plane and is independent of the loading direction. We first consider the limiting cases through poroelastic Backus averaging, and then we obtain the five complex and frequency‐dependent stiffness values of the equivalent transversely isotropic medium as a function of the frequency. The numerical results show that, when the bulk modulus of the fracture‐filling fluid is relatively large, the dispersion and attenuation of P‐waves are mainly caused by fractures, and the values decrease as angles increase, almost vanishing when the incidence angle is 90° (propagation parallel to the fracture plane). While the bulk modulus of fluid in fractures is much smaller than that of matrix pores, the attenuation due to the “partial saturation” mechanism makes the fluid flow from pores into fractures, which is almost independent of the incidence angle. 相似文献
7.
Although it is believed that natural fracture sets predominantly have near‐vertical orientation, oblique stresses and some other mechanisms may tilt fractures away from the vertical. Here, we examine an effective medium produced by a single system of obliquely dipping rotationally invariant fractures embedded in a transversely isotropic with a vertical symmetry axis (VTI) background rock. This model is monoclinic with a vertical symmetry plane that coincides with the dip plane of the fractures. Multicomponent seismic data acquired over such a medium possess several distinct features that make it possible to estimate the fracture orientation. For example, the vertically propagating fast shear wave (and the fast converted PS‐wave) is typically polarized in the direction of the fracture strike. The normal‐moveout (NMO) ellipses of horizontal reflection events are co‐orientated with the dip and strike directions of the fractures, which provides an independent estimate of the fracture azimuth. However, the polarization vector of the slow shear wave at vertical incidence does not lie in the horizontal plane – an unusual phenomenon that can be used to evaluate fracture dip. Also, for oblique fractures the shear‐wave splitting coefficient at vertical incidence becomes dependent on fracture infill (saturation). A complete medium‐characterization procedure includes estimating the fracture compliances and orientation (dip and azimuth), as well as the Thomsen parameters of the VTI background. We demonstrate that both the fracture and background parameters can be obtained from multicomponent wide‐azimuth data using the vertical velocities and NMO ellipses of PP‐waves and two split SS‐waves (or the traveltimes of PS‐waves) reflected from horizontal interfaces. Numerical tests corroborate the accuracy and stability of the inversion algorithm based on the exact expressions for the vertical and NMO velocities. 相似文献
8.
Elastic properties of fluid saturated porous media with aligned fractures can be studied using the model of fractures as linear-slip interfaces in an isotropic porous background. Such a medium represents a particular case of a transversely isotropic (TI) porous medium, and as such can be analyzed with equations of anisotropic poroelasticity. This analysis allows the derivation of explicit analytical expressions for the low-frequency elastic constants and anisotropy parameters of the fractured porous medium saturated with a given fluid. The five elastic constants of the resultant TI medium are derived as a function of the properties of the dry (isotropic) background porous matrix, fracture properties (normal and shear excess compliances), and fluid bulk modulus. For the particular case of penny-shaped cracks, the expression for anisotropy parameter ε has the form similar to that of Thomsen [Geophys. Prospect. 43 (1995) 805]. However, contrary to the existing view, the compliance matrix of a fluid-saturated porous-fractured medium is not equivalent to the compliance matrix of any equivalent solid medium with a single set of parallel fractures. This unexpected result is caused by the wave-induced flow of fluids between pores and fractures. 相似文献
9.
Philip Tillotson Jeremy Sothcott Angus Ian Best Mark Chapman Xiang‐Yang Li 《Geophysical Prospecting》2012,60(3):516-525
We present laboratory ultrasonic measurements of shear‐wave splitting from two synthetic silica cemented sandstones. The manufacturing process, which enabled silica cementation of quartz sand grains, was found to produce realistic sandstones of average porosity 29.7 ± 0.5% and average permeability 29.4 ± 11.3 mD. One sample was made with a regular distribution of aligned, penny‐shaped voids to simulate meso‐scale fractures in reservoir rocks, while the other was left blank. Ultrasonic shear waves were measured with a propagation direction of 90° to the coincident bedding plane and fracture normal. In the water saturated blank sample, shear‐wave splitting, the percentage velocity difference between the fast and slow shear waves, of <0.5% was measured due to the bedding planes (or layering) introduced during sample preparation. In the fractured sample, shear‐wave splitting (corrected for layering anisotropy) of 2.72 ± 0.58% for water, 2.80 ± 0.58% for air and 3.21 ± 0.58% for glycerin saturation at a net pressure of 40 MPa was measured. Analysis of X‐ray CT scan images was used to determine a fracture density of 0.0298 ± 0.077 in the fractured sample. This supports theoretical predictions that shear‐wave splitting (SWS) can be used as a good estimate for fracture density in porous rocks (i.e., SWS = 100εf, where εf is fracture density) regardless of pore fluid type, for wave propagation at 90° to the fracture normal. 相似文献
10.
Fluid flow in many hydrocarbon reservoirs is controlled by aligned fractures which make the medium anisotropic on the scale of seismic wavelength. Applying the linear‐slip theory, we investigate seismic signatures of the effective medium produced by a single set of ‘general’ vertical fractures embedded in a purely isotropic host rock. The generality of our fracture model means the allowance for coupling between the normal (to the fracture plane) stress and the tangential jump in displacement (and vice versa). Despite its low (triclinic) symmetry, the medium is described by just nine independent effective parameters and possesses several distinct features which help to identify the physical model and estimate the fracture compliances and background velocities. For example, the polarization vector of the vertically propagating fast shear wave S1 and the semi‐major axis of the S1‐wave normal‐moveout (NMO) ellipse from a horizontal reflector always point in the direction of the fracture strike. Moreover, for the S1‐wave both the vertical velocity and the NMO velocity along the fractures are equal to the shear‐wave velocity in the host rock. Analysis of seismic signatures in the limit of small fracture weaknesses allows us to select the input data needed for unambiguous fracture characterization. The fracture and background parameters can be estimated using the NMO ellipses from horizontal reflectors and vertical velocities of P‐waves and two split S‐waves, combined with a portion of the P‐wave slowness surface reconstructed from multi‐azimuth walkaway vertical seismic profiling (VSP) data. The stability of the parameter‐estimation procedure is verified by performing non‐linear inversion based on the exact equations. 相似文献
11.
The effect of orthorhombic anisotropy and its implication for oil recovery and reservoir exploitation 总被引：1，自引：0，他引：1
Jamal M. Assad 《Geophysical Prospecting》2005,53(1):121-129
Results of an experimental study of shear‐ and compressional‐wave propagation in an orthorhombically anisotropic medium are presented. The experiments were performed on a physical model consisting of two sets of fractures. The first set consisted of orientated rubber inclusions simulating weak material‐filled cracks. The second set consisted of a system of closely spaced parallel fractures simulated by thin plates of epoxy resin, superimposed orthogonally on the first set. Three cases of fracture orientations within the model were identified and studied. Case 1 is analogous to a jointed fracture reservoir with one vertical set of fluid‐filled cracks or fractures and one non‐filled horizontal set. This case is referred to as JFV. Case 2 is analogous to a double fracture reservoir with one horizontal set of fluid‐filled fractures or cracks and one non‐filled vertical set. This is referred to as DFH. Case 3 is analogous to a double fracture reservoir with two vertical sets of fractures or cracks, with only one fluid‐filled. Case 3 is referred to as DFV. A pulse transmission method was performed on all three modelled cases along the three principal axes. A directional variation in the compressional‐ and shear‐wave velocities, as well as distinct shear‐wave splitting, was observed. The elastic constants for each case were determined and differences between them were noted and compared with the controlled results of both layered (transverse isotropy, TI) and vertically fractured (azimuthally anisotropic models, VF) media. The differences in elastic moduli and velocities indicate the potential of recognizing the different fracture orientations and suggest an approach to designing a method of drilling to further enhance oil recovery and reservoir exploitation. 相似文献
12.
通过对多分量地震资料的分析,我们发现随着频率的增加横波分裂时差减小.对于深部接收的VSP数据来说快横波的偏振方向保持不变,而对于浅层接收的VSP数据来说偏振方向却存在一个最大可以达到20°的旋转.尽管多尺度随机分布微裂隙岩石物理模型已经成功地模拟并解释了横波分裂时差随频率变化的现象,却不能解释与频率相关的横波分裂.据推测,如果微裂隙的排列方向和大裂隙的排列方向不同,利用低频信息获得的偏振方向将指示裂隙主方向,而利用高频信息获得的偏振方向则指示微裂隙方向.在背景多孔隙介质中存在多组裂隙的情况下,推导出垂直入射条件下横波偏振方向的解析式,给出了系统研究横波在介质中传播的方法.研究结果表明,横波偏振方向会随着频率的变化而变化,并且在入射方位、角度一定的条件下,是裂隙方位和密度的函数,这些认识可能有助于揭示观测到的、依赖频率变化的横波偏振现象. 相似文献
13.
Michael A. Schoenberg 《Geophysical Prospecting》2009,57(2):169-185
A vertically fractured transversely isotropic (VFTI) elastic medium is one in which any number of sets of vertical aligned fractures (each set has its normal lying in the horizontal x1, x2‐plane) pervade the medium and the sets of aligned fractures are the only features of the medium disturbing the axi‐symmetry about the x3‐axis implying that in the absence of fractures, the background medium is transversely isotropic (TI). Under the assumptions of long wavelength equivalent medium theory, the compliance matrix of a fractured medium is the sum of the background medium's compliance matrix and a fracture compliance matrix. For sets of parallel rotationally symmetric fractures (on average), the fracture compliance matrix is dependent on 3 parameters − its normal and tangential compliance and its strike direction. When one fracture set is present, the medium is orthorhombic and the analysis is straightforward. When two (non‐orthogonal) or more sets are present, the overall medium is in general elastically monoclinic; its compliance tensor components are subject to two equalities yielding an 11 parameter monoclinic medium. Constructing a monoclinic VFTI medium with n embedded vertical fracture sets, requires 5 TI parameters plus 3×n fracture set parameters. A deconstruction of such an 11 parameter monoclinic medium involves using its compliance tensor to find a background transversely isotropic medium and several sets of vertical fractures which, in the long wavelength limit, will behave exactly as the original 11 parameter monoclinic medium. A minimal deconstruction, would be to determine, from the 11 independent components, the transversely isotropic background (5 parameters) and two fracture sets (specified by 2 × 3 = 6 parameters). Two of the background TI medium's compliance matrix components are known immediately by inspection, leaving nine monoclinic components to be used in the minimal deconstruction of the VFTI medium. The use of the properties of a TI medium, which are linear relations on its compliance components, allows the deconstruction to be reduced to solving a pair of non‐linear equations on the orientations of two fracture sets. A single root yielding a physically meaningful minimum deconstruction yields a unique minimal representation of the monoclinic medium as a VFTI medium. When no such root exists, deconstruction requires an additional fracture set and uniqueness is lost. The boundary between those monoclinic media that have a unique minimal representation and those that do not is yet to be determined. 相似文献
14.
O.H. Al‐Harrasi A. Al‐Anboori A. Wüstefeld J.‐M. Kendall 《Geophysical Prospecting》2011,59(2):227-243
The study of seismic anisotropy in exploration seismology is gaining interest as it provides valuable information about reservoir properties and stress directions. In this study we estimate anisotropy in a petroleum field in Oman using observations of shear‐wave splitting from microseismic data. The data set was recorded by arrays of borehole geophones deployed in five wells. We analyse nearly 3400 microearthquakes, yielding around 8500 shear‐wave splitting measurements. Stringent quality control reduces the number of reliable measurements to 325. Shear‐wave splitting modelling in a range of rock models is then used to guide the interpretation. The difference between the fast and slow shear‐wave velocities along the raypath in the field ranges between 0–10% and it is controlled both by lithology and proximity to the NE‐SW trending graben fault system that cuts the field formations. The anisotropy is interpreted in terms of aligned fractures or cracks superimposed on an intrinsic vertical transversely isotropic (VTI) rock fabric. The highest magnitudes of anisotropy are within the highly fractured uppermost unit of the Natih carbonate reservoir. Anisotropy decreases with depth, with the lowest magnitudes found in the deep part of the Natih carbonate formation. Moderate amounts of anisotropy are found in the shale cap rock. Anisotropy also varies laterally with the highest anisotropy occurring either side of the south‐eastern graben fault. The predominant fracture strikes, inferred from the fast shear‐wave polarizations, are consistent with the trends of the main faults (NE‐SW and NW‐SE). The majority of observations indicate subvertical fracture dip (>70° ). Cumulatively, these observations show how studies of shear‐wave splitting using microseismic data can be used to characterize fractures, important information for the exploitation of many reservoirs. 相似文献
15.
流体在断裂和岩石骨架间的交换被认为是影响岩石弹性参数各向异性的主要原因,理论研究表明断裂尺度同样对弹性参数的各向异性也有影响.为了说明两者对各向异性影响以实现多尺度断裂裂隙的识别,本文在等效介质模型的基础上,应用数值分析的方法研究速度和衰减(1/Q)随多尺度断裂、频率和流体因子变化规律.结果表明介质弹性参数是频率依赖的,并且参数中存在衰减项,而这种频率依赖性与介质物性参数中的断裂尺度及流体性质存在一定的联系;当断裂定向分布时,参数结果显示为各向异性;不同断裂尺度具有不同的波速频散特性,剪切波分裂程度依赖于频率,断裂尺度起着控制作用,高频时对小尺度的敏感,低频段对大尺度敏感.在地震频段Thomsen参数随着频率的增大而减小,随着断裂尺寸的增大而减小.因此地震数据可能区分断裂和微裂隙引起各向异性,从而可测量断裂尺度. 相似文献
16.
The hydrocarbon industry is moving increasingly towards tight sandstone and shale gas resources – reservoirs that require fractures to be produced economically. Therefore, techniques that can identify sets of aligned fractures are becoming more important. Fracture identification is also important in the areas of coal bed methane production, carbon capture and storage (CCS), geothermal energy, nuclear waste storage and mining. In all these settings, stress and pore pressure changes induced by engineering activity can generate or reactivate faults and fractures. P‐ and S‐waves are emitted by such microseismic events, which can be recorded on downhole geophones. The presence of aligned fracture sets generates seismic anisotropy, which can be identified by measuring the splitting of the S‐waves emitted by microseismic events. The raypaths of the S‐waves will have an arbitrary orientation, controlled by the event and geophone locations, meaning that the anisotropy system may only be partly illuminated by the available arrivals. Therefore to reliably interpret such splitting measurements it is necessary to construct models that compare splitting observations with modelled values, allowing the best fitting rock physics parameters to be determined. Commonly, splitting measurements are inverted for one fracture set and rock fabrics with a vertical axis of symmetry. In this paper we address the challenge of identifying multiple aligned fracture sets using splitting measured on microseismic events. We analyse data from the Weyburn CCS‐EOR reservoir, which is known to have multiple fracture sets, and from a hydraulic fracture stimulation, where it is believed that only one set is present. We make splitting measurements on microseismic data recorded on downhole geophone arrays. Our inversion technique successfully discriminates between the single and multiple fracture cases and in all cases accurately identifies the strikes of fracture sets previously imaged using independent methods (borehole image logs, core samples, microseismic event locations). We also generate a synthetic example to highlight the pitfalls that can be encountered if it is assumed that only one fracture set is present when splitting data are interpreted, when in fact more than one fracture set is contributing to the anisotropy. 相似文献
17.
Boris Gurevich 《Geophysical Prospecting》2015,63(1):141-150
Naturally fractured reservoirs are becoming increasingly important for oil and gas exploration in many areas of the world. Because fractures may control the permeability of a reservoir, it is important to be able to find and characterize fractured zones. In fractured reservoirs, the wave‐induced fluid flow between pores and fractures can cause significant dispersion and attenuation of seismic waves. For waves propagating normal to the fractures, this effect has been quantified in earlier studies. Here we extend normal incidence results to oblique incidence using known expressions for the stiffness tensors in the low‐ and high‐frequency limits. This allows us to quantify frequency‐dependent anisotropy due to the wave‐induced flow between pores and fractures and gives a simple recipe for computing phase velocities and attenuation factors of quasi‐P and SV waves as functions of frequency and angle. These frequency and angle dependencies are concisely expressed through dimensionless velocity anisotropy and attenuation anisotropy parameters. It is found that, although at low frequencies, the medium is close to elliptical (which is to be expected as a dry medium containing a distribution of penny‐shaped cracks is known to be close to elliptical); at high frequencies, the coupling between P‐wave and SV‐wave results in anisotropy due to the non‐vanishing excess tangential compliance. 相似文献
18.
A strategy for automated analysis of passive microseismic data to image seismic anisotropy and fracture characteristics 总被引：1，自引：0，他引：1
Andreas Wuestefeld Othman Al‐Harrasi James P. Verdon James Wookey J. Michael Kendall 《Geophysical Prospecting》2010,58(5):755-773
Monitoring of induced seismicity is gaining importance in a broad range of industrial operations from hydrocarbon reservoirs to mining to geothermal fields. Such passive seismic monitoring mainly aims at identifying fractures, which is of special interest for safety and productivity reasons. By analysing shear‐wave splitting it is possible to determine the anisotropy of the rock, which may be caused by sedimentary layering and/or aligned fractures, which in turn offers insight into the state of stress in the reservoir. We present a workflow strategy for automatic and effective processing of passive microseismic data sets, which are ever increasing in size. The automation provides an objective quality control of the shear‐wave splitting measurements and is based on characteristic differences between the two independent eigenvalue and cross‐correlation splitting techniques. These differences are summarized in a quality index for each measurement, allowing identification of an appropriate quality threshold. Measurements above this threshold are considered to be of good quality and are used in further interpretation. We suggest an automated inversion scheme using rock physics theory to test for best correlation of the data with various combinations of fracture density, its strike and the background anisotropy. This fully automatic workflow is then tested on a synthetic and a real microseismic data set. 相似文献
19.
利用新方法制作出含可控裂缝的双孔隙人工砂岩物理模型,具有与天然岩石更为接近的矿物成分、孔隙结构和胶结方式,其中裂缝密度、裂缝尺寸和裂缝张开度等裂缝参数可以控制以得到实验所需要的裂缝参数,岩样具有真实的孔隙和裂缝空间并可以在不同饱和流体状态下研究流体性质对于裂缝介质性质的影响.本次实验制作出一组具有不同裂缝密度的含裂缝人工岩样,对岩样利用SEM扫描电镜分析可以看到真实的孔隙结构和符合我们要求的裂缝参数,岩样被加工成八面棱柱以测量不同方向上弹性波传播的速度,用0.5 MHz的换能器使用透射法测量在饱和空气和饱和水条件下各个样品不同方向上的纵横波速度,并得出纵横波速度、横波分裂系数和纵横波各向异性强度受裂缝密度和饱和流体的影响.研究发现流体对于纵波速度和纵波各向异性强度的影响较强,而横波速度、横波分裂系数和横波各向异性强度受饱和流体的影响不大,但是对裂缝密度的变化更敏感. 相似文献
20.
Wave‐induced fluid flow plays an important role in affecting the seismic dispersion and attenuation of fractured porous rocks. While numerous theoretical models have been proposed for the seismic dispersion and attenuation in fractured porous rocks, most of them neglect the wave‐induced fluid flow resulting from the background anisotropy (e.g. the interlayer fluid flow between different layers) that can be normal in real reservoirs. Here, according to the theories of poroelasticity, we present an approach to study the frequency‐dependent seismic properties of more realistic and complicated rocks, i.e. horizontally and periodically layered porous rock with horizontal and randomly orienting fractures, respectively, distributed in one of the two periodical layers. The approach accounts for the dual effects of the wave‐induced fluid flow between the fractures and the background pores and between different layers (the interlayer fluid flow). Because C33 (i.e., the modulus of the normally incident P‐wave) is directly related to the P‐wave velocity widely measured in the seismic exploration, and its comprehensive dispersion and attenuation are found to be most significant, we study mainly the effects of fracture properties and the stiffness contrast between the different layers on the seismic dispersion and attenuation of C33. The results show that the increasing stiffness contrast enhances the interlayer fluid flow of the layered porous rocks with both horizontal and randomly orienting fractures and weakens the wave‐induced fluid flow between the fractures and the background pores, especially for the layered porous rock with horizontal fractures. The modelling results also demonstrate that for the considered rock construction, the increasing fracture density reduces the interlayer fluid flow while improves the dispersion and attenuation in the fracture‐relevant frequency band. Increasing fracture aspect ratio is found to reduce the dispersion and attenuation in the fracture‐relevant frequency band only, especially for the layered porous rock with horizontal fractures. 相似文献