共查询到20条相似文献，搜索用时 15 毫秒
1.
O.H. Al‐Harrasi A. Al‐Anboori A. Wüstefeld J.‐M. Kendall 《Geophysical Prospecting》2011,59(2):227-243
The study of seismic anisotropy in exploration seismology is gaining interest as it provides valuable information about reservoir properties and stress directions. In this study we estimate anisotropy in a petroleum field in Oman using observations of shear‐wave splitting from microseismic data. The data set was recorded by arrays of borehole geophones deployed in five wells. We analyse nearly 3400 microearthquakes, yielding around 8500 shear‐wave splitting measurements. Stringent quality control reduces the number of reliable measurements to 325. Shear‐wave splitting modelling in a range of rock models is then used to guide the interpretation. The difference between the fast and slow shear‐wave velocities along the raypath in the field ranges between 0–10% and it is controlled both by lithology and proximity to the NE‐SW trending graben fault system that cuts the field formations. The anisotropy is interpreted in terms of aligned fractures or cracks superimposed on an intrinsic vertical transversely isotropic (VTI) rock fabric. The highest magnitudes of anisotropy are within the highly fractured uppermost unit of the Natih carbonate reservoir. Anisotropy decreases with depth, with the lowest magnitudes found in the deep part of the Natih carbonate formation. Moderate amounts of anisotropy are found in the shale cap rock. Anisotropy also varies laterally with the highest anisotropy occurring either side of the south‐eastern graben fault. The predominant fracture strikes, inferred from the fast shear‐wave polarizations, are consistent with the trends of the main faults (NE‐SW and NW‐SE). The majority of observations indicate subvertical fracture dip (>70° ). Cumulatively, these observations show how studies of shear‐wave splitting using microseismic data can be used to characterize fractures, important information for the exploitation of many reservoirs. 相似文献
2.
Colin M. Sayers 《Geophysical Prospecting》2002,50(4):393-401
Azimuthal anisotropy in rocks can result from the presence of one or more sets of partially aligned fractures with orientations determined by the stress history of the rock. A shear wave propagating in an azimuthally anisotropic medium splits into two components with different polarizations if the source polarization is not aligned with the principal axes of the medium. For vertical propagation of shear waves in a horizontally layered medium containing vertical fractures, the shear‐wave splitting depends on the shear compliance of the fractures, but is independent of their normal compliance. If the fractures are not perfectly vertical, the shear‐wave splitting also depends on the normal compliance of the fractures. The normal compliance of a fluid‐filled fracture decreases with increasing fluid bulk modulus. For dipping fractures, this results in a decrease in shear‐wave splitting and an increase in shear‐wave velocity with increasing fluid bulk modulus. The sensitivity of the shear‐wave splitting to fluid bulk modulus depends on the interconnectivity of the fracture network, the permeability of the background medium and on whether the fracture is fully or partially saturated. 相似文献
3.
裂缝广泛分布于地球介质中并且具有多尺度的特点,裂缝尺度对于油气勘探和开发有着重要的意义.本文制作了一组含不同长度裂缝的人工岩样,其中三块含裂缝岩样中的裂缝直径分别为2 mm、3 mm和4 mm,裂缝的厚度都约为0.06 mm,裂缝密度大致相同(分别为4.8%、4.86%和4.86%).在岩样含水的条件下测试不同方向上的纵横波速度,实验结果表明,虽然三块裂缝岩样中的裂缝密度大致相同,但是含不同直径裂缝岩样的纵横波速度存在差异.在各个方向上,含数量众多的小尺度裂缝的岩样中纵横波速度都明显低于含少量的大尺度裂缝的岩样中纵横波速度.尤其是对纵波速度和SV波速度,在不同尺度裂缝岩样中的差异更明显.在含数量多的小尺度裂缝的岩样中纵波各向异性和横波各向异性最高,而含少量的大尺度的裂缝的岩样中的纵波各向异性和横波各向异性较低.实验测量结果与Hudson理论模型预测结果进行了对比分析,结果发现Hudson理论考虑到了裂缝尺度对纵波速度和纵波各向异性的影响,但是忽略了其对横波速度和横波各向异性的影响. 相似文献
4.
The hydrocarbon industry is moving increasingly towards tight sandstone and shale gas resources – reservoirs that require fractures to be produced economically. Therefore, techniques that can identify sets of aligned fractures are becoming more important. Fracture identification is also important in the areas of coal bed methane production, carbon capture and storage (CCS), geothermal energy, nuclear waste storage and mining. In all these settings, stress and pore pressure changes induced by engineering activity can generate or reactivate faults and fractures. P‐ and S‐waves are emitted by such microseismic events, which can be recorded on downhole geophones. The presence of aligned fracture sets generates seismic anisotropy, which can be identified by measuring the splitting of the S‐waves emitted by microseismic events. The raypaths of the S‐waves will have an arbitrary orientation, controlled by the event and geophone locations, meaning that the anisotropy system may only be partly illuminated by the available arrivals. Therefore to reliably interpret such splitting measurements it is necessary to construct models that compare splitting observations with modelled values, allowing the best fitting rock physics parameters to be determined. Commonly, splitting measurements are inverted for one fracture set and rock fabrics with a vertical axis of symmetry. In this paper we address the challenge of identifying multiple aligned fracture sets using splitting measured on microseismic events. We analyse data from the Weyburn CCS‐EOR reservoir, which is known to have multiple fracture sets, and from a hydraulic fracture stimulation, where it is believed that only one set is present. We make splitting measurements on microseismic data recorded on downhole geophone arrays. Our inversion technique successfully discriminates between the single and multiple fracture cases and in all cases accurately identifies the strikes of fracture sets previously imaged using independent methods (borehole image logs, core samples, microseismic event locations). We also generate a synthetic example to highlight the pitfalls that can be encountered if it is assumed that only one fracture set is present when splitting data are interpreted, when in fact more than one fracture set is contributing to the anisotropy. 相似文献
5.
6.
Understanding fracture orientations is important for optimal field development of fractured reservoirs because fractures can act as conduits for fluid flow. This is especially true for unconventional reservoirs (e.g., tight gas sands and shale gas). Using walkaround Vertical Seismic Profiling (VSP) technology presents a unique opportunity to identify seismic azimuthal anisotropy for use in mapping potential fracture zones and their orientation around a borehole. Saudi Aramco recently completed the acquisition, processing and analysis of a walkaround VSP survey through an unconventional tight gas sand reservoir to help characterize fractures. In this paper, we present the results of the seismic azimuthal anisotropy analysis using seismic traveltime, shear‐wave splitting and amplitude attenuation. The azimuthal anisotropy results are compared to the fracture orientations derived from dipole sonic and image logs. The image log interpretation suggests that an orthorhombic fracture system is present. VSP data show that the P‐wave traveltime anisotropy direction is NE to SW. This is consistent with the cemented fractures from the image log interpretation. The seismic amplitude attenuation anisotropy direction is NW to SE. This is consistent with one of the two orientations obtained using transverse to radial amplitude ratio analysis, with the dipole sonic and with open fracture directions interpreted from image log data. 相似文献
7.
8.
Estimating azimuthal stress‐induced P‐wave anisotropy from S‐wave anisotropy using sonic log or vertical seismic profile data 
下载免费PDF全文
下载免费PDF全文 Most sedimentary rocks are anisotropic, yet it is often difficult to accurately incorporate anisotropy into seismic workflows because analysis of anisotropy requires knowledge of a number of parameters that are difficult to estimate from standard seismic data. In this study, we provide a methodology to infer azimuthal P‐wave anisotropy from S‐wave anisotropy calculated from log or vertical seismic profile data. This methodology involves a number of steps. First, we compute the azimuthal P‐wave anisotropy in the dry medium as a function of the azimuthal S‐wave anisotropy using a rock physics model, which accounts for the stress dependency of seismic wave velocities in dry isotropic elastic media subjected to triaxial compression. Once the P‐wave anisotropy in the dry medium is known, we use the anisotropic Gassmann equations to estimate the anisotropy of the saturated medium. We test this workflow on the log data acquired in the North West Shelf of Australia, where azimuthal anisotropy is likely caused by large differences between minimum and maximum horizontal stresses. The obtained results are compared to azimuthal P‐wave anisotropy obtained via orthorhombic tomography in the same area. In the clean sandstone layers, anisotropy parameters obtained by both methods are fairly consistent. In the shale and shaly sandstone layers, however, there is a significant discrepancy between results since the stress‐induced anisotropy model we use is not applicable to rocks exhibiting intrinsic anisotropy. This methodology could be useful for building the initial anisotropic velocity model for imaging, which is to be refined through migration velocity analysis. 相似文献
9.
Azimuthal anisotropy in lithosphere on the Chinese mainland from observations of SKS at CDSN 总被引：2，自引：0，他引：2
Ａｚｉｍｕｔｈａｌ ａｎｉｓｏｔｒｏｐｙ ｉｎ ｌｉｔｈｏｓｐｈｅｒｅ ｏｎ ｔｈｅ Ｃｈｉｎｅｓｅ ｍａｉｎｌａｎｄ ｆｒｏｍ ｏｂｓｅｒｖａｔｉｏｎｓ ｏｆ ＳＫＳ ａｔ ＣＤＳＮ（郑斯华）（高原）Ａｚｉｍｕｔｈａｌａｎｉｓｏｔｒｏｐｙｉｎｌｉｔ... 相似文献
10.
通过对多分量地震资料的分析,我们发现随着频率的增加横波分裂时差减小.对于深部接收的VSP数据来说快横波的偏振方向保持不变，而对于浅层接收的VSP数据来说偏振方向却存在一个最大可以达到20°的旋转.尽管多尺度随机分布微裂隙岩石物理模型已经成功地模拟并解释了横波分裂时差随频率变化的现象，却不能解释与频率相关的横波分裂.据推测，如果微裂隙的排列方向和大裂隙的排列方向不同，利用低频信息获得的偏振方向将指示裂隙主方向，而利用高频信息获得的偏振方向则指示微裂隙方向.在背景多孔隙介质中存在多组裂隙的情况下，推导出垂直入射条件下横波偏振方向的解析式，给出了系统研究横波在介质中传播的方法.研究结果表明，横波偏振方向会随着频率的变化而变化，并且在入射方位、角度一定的条件下，是裂隙方位和密度的函数，这些认识可能有助于揭示观测到的、依赖频率变化的横波偏振现象. 相似文献
11.
根据乌海地区构造环境，采用SAM方法研究乌海地区地壳各向异性特征，使用乌海地震台2014年1月至2020年6月数字地震波形进行分析。根据65个有效地震记录，得到乌海地区剪切波分裂参数，其中快剪切波平均优势偏振方向为NE63.1°±46.4°，慢剪切波平均时间延迟为（1.13±0.66）ms/km。乌海地震台快剪切波偏振显示出4个优势偏振方向，分别为NE、EW、NNE、NNW向。将得到的各向异性结果与研究区应力场和地质构造进行分析，认为研究区周边复杂的剪切波分裂变化是主压应力场、原地主压应力、断裂带分布共同作用的结果。 相似文献
12.
大理岩的波速各向异性测量 总被引：4，自引：0，他引：4
利用 GC- 1 0 0型工程多波参数分析仪 ,对山东莱州大理岩进行了波速各向异性的实验室观测。实验采用两组岩样 ,一组为带有先天的优势定向排列裂缝的岩样 ,另一组为带有优势层理走向的完整岩石。在未加载的状态下 ,发现两组岩样都有明显的波速方位各向异性。对于带有先天的优势定向排列裂缝的岩样 ,甚至可以在无加载状态下观测到剪切波的分裂现象 相似文献
13.
Shear wave splitting is a well-known method for indication of orientation, radius, and length of fractures in subsurface layers. In this paper, a three component near offset VSP data acquired from a fractured sandstone reservoir in southern part of Iran was used to analyse shear wave splitting and frequency-dependent anisotropy assessment. Polarization angle obtained by performing rotation on radial and transverse components of VSP data was used to determine the direction of polarization of fast shear wave which corresponds to direction of fractures. It was shown that correct implementation of shear wave splitting analysis can be used for determination of fracture direction. During frequencydependent anisotropy analysis, it was found that the time delays in shearwaves decrease as the frequency increases. It was clearly demonstrated throughout this study that anisotropy may have an inverse relationship with frequency. The analysis presented in this paper complements the studied conducted by other researchers in this field of research. 相似文献
14.
利用横波分裂分析获取地下介质的各向异性参数,已成为研究壳幔介质变形特征最为有效的方法之一。本文首先介绍横波分裂理论方程的推导过程;然后阐述目前几种较为常用的拾取横波分裂参数的方法;最后总结近年来横波分裂分析方法的发展现状及其在地壳介质各向异性研究方面取得的成果。我们认为尽管横波分裂分析方法被广泛应用于地壳介质各向异性研究,但是它也存在一些固有的局限性,期望未来能发展一种更为可靠、有效的方法以及数据处理流程来准确拾取横波分裂参数。 相似文献
15.
有关青藏高原横波分裂的各向异性研究已经开展了近30年,在理论方法和实际应用方面取得了重要进展,并获取了大量的横波分裂测量结果,为认识青藏高原壳幔各向异性变形特征和动力学机制提供了重要的依据.本文首先介绍了地震各向异性的来源与应用,随后回顾了横波分裂分析方法的发展,简述了各种横波分裂方法的原理,最后通过总结近30年来青藏高原上地壳、整个地壳和上地幔横波分裂各向异性研究成果,系统分析了青藏高原壳幔各向异性变形特征.基于各横波分裂结果的对比分析来看,XKS波分裂测量结果最为稳定,近震直达S波分裂测量结果次之,而Pms波分裂测量结果相对离散,往往相同区域内不同的研究结果差异较大,主要原因可能是相比XKS波和近震直达S波,Pms波的信噪比较低,次要原因可能是各研究在方法和处理分析等方面的差异. 相似文献
16.
横波各向异性在裂缝和应力分析中的应用 总被引：1，自引：0，他引：1
针对裂缝性和低孔低渗地层的横波各向异性特征,反演得到横波各向异性参数,研究了裂缝的发育程度、方位和有效性,并对低孔低渗地层的应力场分布状态和方位进行了综合评价;通过对反演得到的快、慢弯曲波形进行频散分析以及计算单极横波各向异性大小,确定了引起横波各向异性的原因,并结合常规测井资料、岩心及FMI成像资料对分析结果进行了验证和对比,最后对研究区8口典型井的横波各向异性进行了综合处理和评价,得到了该区的横波各向异性特征以及和总的应力场走向.结果表明,利用横波的各向异性参数可以有效的评价裂缝的发育程度、走向及有效性,并能准确的确定地应力分布状态和最大水平应力方位. 相似文献
17.
利用新方法制作出含可控裂缝的双孔隙人工砂岩物理模型,具有与天然岩石更为接近的矿物成分、孔隙结构和胶结方式,其中裂缝密度、裂缝尺寸和裂缝张开度等裂缝参数可以控制以得到实验所需要的裂缝参数,岩样具有真实的孔隙和裂缝空间并可以在不同饱和流体状态下研究流体性质对于裂缝介质性质的影响.本次实验制作出一组具有不同裂缝密度的含裂缝人工岩样,对岩样利用SEM扫描电镜分析可以看到真实的孔隙结构和符合我们要求的裂缝参数,岩样被加工成八面棱柱以测量不同方向上弹性波传播的速度,用0.5 MHz的换能器使用透射法测量在饱和空气和饱和水条件下各个样品不同方向上的纵横波速度,并得出纵横波速度、横波分裂系数和纵横波各向异性强度受裂缝密度和饱和流体的影响.研究发现流体对于纵波速度和纵波各向异性强度的影响较强,而横波速度、横波分裂系数和横波各向异性强度受饱和流体的影响不大,但是对裂缝密度的变化更敏感. 相似文献
18.
J.V. Herwanger M.H. Worthington † R. Lubbe † A. Binley J. Khazanehdari 《Geophysical Prospecting》2004,52(2):109-121
Cross‐hole anisotropic electrical and seismic tomograms of fractured metamorphic rock have been obtained at a test site where extensive hydrological data were available. A strong correlation between electrical resistivity anisotropy and seismic compressional‐wave velocity anisotropy has been observed. Analysis of core samples from the site reveal that the shale‐rich rocks have fabric‐related average velocity anisotropy of between 10% and 30%. The cross‐hole seismic data are consistent with these values, indicating that observed anisotropy might be principally due to the inherent rock fabric rather than to the aligned sets of open fractures. One region with velocity anisotropy greater than 30% has been modelled as aligned open fractures within an anisotropic rock matrix and this model is consistent with available fracture density and hydraulic transmissivity data from the boreholes and the cross‐hole resistivity tomography data. However, in general the study highlights the uncertainties that can arise, due to the relative influence of rock fabric and fluid‐filled fractures, when using geophysical techniques for hydrological investigations. 相似文献
19.
Mark Chapman Jeremy Sothcott Angus Ian Best Xiang‐Yang Li 《Geophysical Prospecting》2014,62(6):1238-1252
Ultrasonic (500 kHz) P‐ and S‐wave velocity and attenuation anisotropy were measured in the laboratory on synthetic, octagonal‐shaped, silica‐cemented sandstone samples with aligned penny‐shaped voids as a function of pore fluid viscosity. One control (blank) sample was manufactured without fractures, another sample with a known fracture density (measured from X‐ray CT images). Velocity and attenuation were measured in four directions relative to the bedding fabric (introduced during packing of successive layers of sand grains during sample construction) and the coincident penny‐shaped voids (fractures). Both samples were measured when saturated with air, water (viscosity 1 cP) and glycerin (100 cP) to reveal poro‐visco‐elastic effects on velocity and attenuation, and their anisotropy. The blank sample was used to estimate the background anisotropy of the host rock in the fractured sample; the bedding fabric was found to show transverse isotropy with shear wave splitting (SWS) of 1.45 ± 1.18% (i.e. for S‐wave propagation along the bedding planes). In the fractured rock, maximum velocity and minimum attenuation of P‐waves was seen at 90° to the fracture normal. After correction for the background anisotropy, the fractured sample velocity anisotropy was expressed in terms of Thomsen's weak anisotropy parameters ε, γ & δ. A theory of frequency‐dependent seismic anisotropy in porous, fractured, media was able to predict the observed effect of viscosity and bulk modulus on ε and δ in water‐ and glycerin‐saturated samples, and the higher ε and δ values in air‐saturated samples. Theoretical predictions of fluid independent γ are also in agreement with the laboratory observations. We also observed the predicted polarisation cross‐over in shear‐wave splitting for wave propagation at 45° to the fracture normal as fluid viscosity and bulk modulus increases. 相似文献
20.
The collision of the Indian and Eurasian plates, to the east of the eastern Himalayan syntaxes, forms the Sanjiang lateral collision zone in the southeast margin of the Tibetan Plateau, where there are intense crustal deformation, active faults, earthquakes, as well as a metallogenic belt. Given the lack of adequate seismic data, shear-wave splitting in this area has not been studied. With seismic data from a temporary seismic linear array, as well as permanent seismic stations, this paper adopts the identification on microseismic event to pick more events and obtains shear-wave splitting parameters from local earthquakes. From the west to the east, the study area can be divided into three subzones. The “fast” polarization (i.e. the polarization of the fast shear wave) varies gradually from NNW to NS to NNE in these three subzones. The time delay of the slow shear wave (i.e. the time difference between the two split shear waves) also increases in the same direction, indicating the presence of seismic anisotropy above 25 km in the crust. Both shear-wave splitting parameters are closely related to stress, faults and tectonics. The scatter and the “dual” (i.e. two) dominant orientations of the fast polarizations at several stations indicate strong distortions caused by nearby faults or deep tectonics. The anisotropic parameters are found to be related to some degree to the metallogenic belt. It is worth to further analyse the link between the anisotropic pattern and the metallogenic area, which suggests that shear-wave splitting could be applied to study metallogeny. This paper demonstrates that the identification on microseismic event is a useful tool in detecting shear-wave splitting details and exploring its tectonic implications. 相似文献