共查询到20条相似文献，搜索用时 31 毫秒
1.
Gerstoft P. Hodgkiss W.S. Kuperman W.A. Heechun Song Siderius M. Nielsen P.L. 《Oceanic Engineering, IEEE Journal of》2003,28(1):44-54
During maneuvering, towed array beamforming degrades if a straight array is assumed. This is especially true for high-resolution adaptive beamforming. It is experimentally demonstrated that adaptive beamforming is feasible on a turning array, provided that array shape is estimated. The array shape can be inferred solely from the coordinates of the tow vessel's Global Positioning System (GPS) without any instrumentation in the array. Based on estimated array shape from the GPS, both the conventional beamformer and the white noise constrained (WNC) adaptive beamformer are shown to track the source well during a turn. When calculating the weight vector in the WNC approach, a matrix inversion of the cross-spectral density matrix is involved. This matrix inversion can be stabilized by averaging the cross-spectral density matrix over neighboring frequencies. The proposed algorithms have been tested on real data with the tow-vessel making 45/spl deg/ turns with a 500-m curvature radius. While turning, the improvement in performance over the assumption of a straight array geometry was up to 5 dB for the conventional beamformer and considerably larger for the WNC adaptive beamformer. 相似文献
2.
Groen J. Beerens S.P. Been R. Doisy Y. Noutary E. 《Oceanic Engineering, IEEE Journal of》2005,30(2):348-359
For a low-frequency active sonar (LFAS) with a triplet receiver array, it is not clear in advance which signal processing techniques optimize its performance. Here, several advanced beamformers are analyzed theoretically, and the results are compared to experimental data obtained in sea trials. Triplet arrays are single line arrays with three hydrophones on a circular section of the array. The triplet structure provides the ability to solve the notorious port-starboard (PS) ambiguity problem of ordinary single-array receivers. More importantly, the PS rejection can be so strong that it allows to unmask targets in the presence of strong coastal reverberation or traffic noise. The theoretical and experimental performance of triplet array beamformers is determined in terms of two performance indicators: array gain and PS rejection. Results are obtained under several typical acoustic environments: sea noise, flow noise, coastal reverberation, and mixtures of these. A new algorithm for (beam space) adaptive triplet beamforming is implemented and tuned. Its results are compared to those of other triplet beamforming techniques (optimum and cardioid beamforming). These beamformers optimize for only one performance indicator, whereas in theory, the adaptive beamformer gives the best overall performance (in any given environment). The different beamformers are applied to data obtained with an LFAS at sea. Analysis shows that adaptive triplet beamforming outperforms conventional beamforming algorithms. Adaptive triplet beamforming provides strong PS rejection, allowing the unmasking of targets in the presence of strong directional reverberation (e.g., from a coast) and at the same time provides positive array gain in most environments. 相似文献
3.
A numerical optimization technique that uses sonar array noise measurements is used to determine conventional shading weights that maximize the broadband deflection coefficient at the output of the optimal square-law detector, across a frequency band of interest. This process maintains the structure of the conventional processor while providing performance improvement typical of adaptive techniques. The performance of the optimized time domain delay-and-sum beamformer is compared with that of the traditional beamformer that uses conventionally chosen shading weights. Application of this method to conformal velocity sonar array data is shown to provide large improvements in performance over heuristic designs. 相似文献
4.
The Three-Array Processor (TAP III) beamforming system incorporating both wide-band time-domain beamforming and narrow-band frequency-domain beamforming is described. This paper briefly develops the beamforming theory and shows how the fast Fourier transform (FFT) is applied to accomplish frequency-domain beamforming. The frequency-domain beamformer operates in the frequency domain to form beams and power spectrum data over narrow frequency bands of interest. A real-time digital filtering technique is used to extract the narrow bands of interest from the broad-band input signal. The frequency-domain beamformer accomplishes real-time digital filtering and beamforming by using a high-speed array processor to do the complex calculations and data handling required by the algorithm. The time-domain beamformer operates in parallel with the frequency-domain beamformer to form up to 16 broad-band beams in the time domain. A programmable all-pass digital filter is used to create the fine time delays required by the time-domain beamformer. 相似文献
5.
Reverberation rejection with a dual-line towed array 总被引：1，自引：0，他引：1
Low-frequency bottom reverberation from explosive sources was measured with a dual-line horizontal towed array during a 1991 system engineering trial. The receiver's parallel line arrays were processed coherently in order to unambiguously resolve the reverberation field in azimuth. Initial beamforming that assumed a straight-and-parallel array configuration led to poor or erroneous ambiguity resolution, suggesting the system was deformed significantly from the assumed shape. In the absence of reliable shape measurement data, the array shape was deduced acoustically using tow ship signals and the direct blast of an explosive source. The estimated shape was then used in a shape-compensated beamformer to produce azimuthally unambiguous estimates of the reverberation field. Backlobe rejection of more than 20 dB was attained for both direct blast and distant reverberation energy 相似文献
6.
Various approaches to the beamforming of data from large aperture vertical line arrays are investigated. Attention is focused on the conventional beamforming problem where the angular power spectrum is estimated, in this case by the adaptive minimum variance processor. The data to be processed are 200 Hz CW transmissions collected at sea by a 900 m vertical line array with 120 equally spaced sensors. Correlated multipath arrivals result in signal cancellation for the adaptive processor, and spatial smoothing techniques must be used prior to beamforming. The processing of subapertures is proposed. Full aperture and subaperture processing techniques are used on the 200 Hz data. Multipath arrivals are found to illuminate only parts of the array, thus indicating that the wavefield can be highly inhomogeneous with depth 相似文献
7.
常规波束形成器仅限于利用信号的二阶统计特性。作者采用高阶累积量估计期望信号的导向矢量 (Steering Vector) ,实现了一种基于高阶累积量的自适应波束形成器 (HCAB)。该波束形成器利用信号的更高阶统计特性 ,减少了对阵列流型的依赖 ,具有较好的容差性 ,能自动跟踪信号。数值模拟实验表明该波束形成器工作良好。 相似文献
8.
9.
Controlling the resolution in adaptive beamformers is often crucial. A simple method that works for both narrow-band and broad-band arrays is presented. This method is based on the normalized leaky LMS algorithm in conjunction with a generalized sidelobe canceller (GSC) structure, where the GSC is designed using a spatial filtering approach. In essence, the suppression of the spatial filters and the implicit noise of the leaky LMS algorithm together determine the adaptive beamformer. Analytical expressions are given for the Wiener filters and the output spectrum versus frequency and point source location. These expressions are employed in the design specification of the spatial filters and to obtain conditions for a controlled quiescent beamformer response. Simulation results are presented to illustrate the behavior of the array 相似文献
10.
Towed array beamforming algorithms require accurate array shape information in order to perform properly. Very often, these algorithms assume the array is linear. Unfortunately, the mechanical forces on the array due to ship motion and sea dynamics can change the shape of the array, which degrades the performance of the beamforming algorithm. A data-driven approach to estimating the relative shape of a nominally linear array is presented. The algorithm is robust in that it optimally combines information contained in a wide band of frequencies and source bearings. At the heart of the algorithm is a maximum-likelihood (ML) estimation scheme. The Cramer-Rao lower bound is derived and compared to the performance of the ML estimator. The utility of the algorithm is verified using both simulated and actual towed array data experiments 相似文献
11.
The Wigner-Ville distribution (WVD) function was originally proposed by Wigner in quantum mechanics and Ville applied it for signal analysis. This method has made it possible to represent a signal's power density spectrum in the time-frequency domain as a natural extension of the Fourier transform method (FTM). Recently, it has attracted great interest for its validity to analyze time-varying signals accomplished by the development of high-speed digital signal processing, and it is used for analyzing nonstationary signals. Conventionally, a sonar beamformer is constructed using delay lines, but the development of the high-speed processor has made it possible to apply the FTM for sonar beamforming. However, the bearing resolution of the beamformer is not enough for discriminating small underwater objects on the sea bottom by this method. To solve this problem, we aim to apply the WVD method, which can represent finer structure of signals as a natural extension of the FTM, for sonar beamforming to obtain sharper beam patterns than those of the beamforming method by FTM. Simulation results by computational calculations to clarify the resolution by the WVD method, which is presented in this paper, becomes approximately twice as high as by conventional FTM. The results of an experiment at sea also show the performance of this method 相似文献
12.
Increasing the number of hydrophones in an array should increase beamformer performance. However, when the number of hydrophones is large, integration times must be long enough to give accurate cross-spectral matrix (CSM) estimates, but short enough so that the dynamic behavior of the noise described by the CSM is captured. The dominant mode rejection (DMR) beamformer calculates adaptive weights based on a reduced rank CSM estimate, where the CSM estimate is formed with a subset of the largest eigenvalues and their eigenvectors. Since the largest eigenvalue/eigenvector pairs are estimated rapidly, the integration time required is reduced. The purpose of this study was to examine the DMR beamformer performance using a bottom-mounted horizontal line array in a shallow-water environment. The data were processed with a fully adaptive beamformer and the DMR beamformer. The DMR beamformer showed better performance than the fully adaptive beamformer when using arrays with larger numbers of hydrophones. Thus, in highly dynamic noise environments, the DMR beamformer may be a more appropriate implementation to use for passive sonar detection systems 相似文献
13.
An optimal evaluation of adaptive beamforming techniques in a reverberation-limited shallow water environment is presented. A comprehensive simulation, using the sonar simulation toolset (SST) software in conjunction with the generic sonar model (GSRT) software, is used to create realistic beam data complete with target, noise, and reverberation. Adaptive beamforming techniques from the recursive least squares (RLS) family are applied to enhance detection performance via interference rejection. Two techniques are considered: linearly constrained beamforming using the minimum variance distortionless response (MVOR) beamformer and constrained adaptive noise cancelling (ANC) using the joint process least squares lattice (JPLSL) algorithm. Target detection trials, summarized in the form of receiver operator characteristics (ROC), are used to evaluate performance of the two adaptive beamformers. Results demonstrate mixed performance in reverberation-limited shallow water environments 相似文献
14.
15.
Subspace-tracking algorithms have traditionally been unable to deal with a large number of sources and at the same timepreserve their computationally efficiency, since, typically, efficiency goes down as the cube of the signal subspace dimension. One solution to this problem, which is presented in this paper, is to use a newly developed algorithm for the design of spatial filters in matrix form, in order to spatially filter the incoming data snapshots. The result is that the signal subspaces are confined to small angular sectors and, thus, the effective number of signals present is reduced. A method is developed for designing spatial filters in an efficient manner by formulating the design procedure as a rank-deficient linear least-squares problem. The source-bearing estimation is done using the signal-covariance matrix, which is updated using a recently developed fast algorithm, which is necessary in situations where one or more sources are nonstationary. The combination of the subspace-based bearing-estimation and spatial filter algorithms is shown to give good performance in cases of medium signal-to-noise ratio and is capable of resolving sources that are below the resolution limit of both conventional and adaptive beamforming. In addition, the use of spatial filtering makes it possible to estimate bearings for more than N narrow-band sources, using an N-element array. An example illustrating this capability is given. 相似文献
16.
Acoustic signal parameter estimation is important for diverse marine geodesy surveys and several other applications. However, the received signal from a far-field target characterized by planar wavefront propagation is frequently affected by strong nearby interfering signals. Their presence deteriorates the performance of direction-of-arrival (DOA) estimation for far-field target. In order to enhance the reception of signal from far-field target, the near-field/far-field (NFFF) beamformer is proposed. Such a beamformer optimizes beam pattern for far-field detection by maximizing beamformer output in the direction of the far-field target with the imposed condition to eliminate interfering signals generated in near-field locations. As the interference suppression only occurs at the position of near-field interference, a possible blind zone for far-field detection in conventional methods is not created. The NFFF beamformer is applicable for coherent signals and the scenario with multi interferences. For stationary situation where interferers locations are fixed, the NFFF beamformer computations do not require time updates with associated computational load. Furthermore the proposed method can be extended to several new situations such as acoustic monitoring performed from a stationary platform subjected to water currents, waves, winds and other variables, all of them generating nearby interferences and also to different array configurations including 2D and 3D arrays. 相似文献
17.
在多波束回声声纳系统中，高分辨处理算法例如MUSIC、ESPRIT，被广泛应用于海底地形的测绘。在应用高分辨算法时，一条均匀线阵是必要条件。然而，由于系统覆盖范围/分辨率的需求以及安装空间的限制，在多波束系统中经常会采用特殊形状的接收阵列，这使得高分辨算法无法直接应用。同时回波信号的短时平稳特性使得难以估计出协方差矩阵，这也增加了高分辨算法在多波束系统中的应用难度。本文首先介绍一种基于多角度子阵波束形成的ESPRIT算法，该算法能降低高分辨算法对信噪比、样本点数和计算能力的要求。仿真表明此算法能提供更好的分辨力。接着提出一种将基于多角度子阵波束形成的ESPRIT算法与虚拟阵列变换相结合的高分辨底检测算法，并针对高分辨底检测算法在U型阵上的应用进行了探讨。计算机仿真和试验数据处理结果验证了文章所提高分辨底检测算法的有效性。 相似文献
18.
Passive sonar systems that localize broadband sources of acoustic energy estimate the difference in arrival times (or time delays) of an acoustic wavefront at spatially separated hydrophones, The output amplitudes from a given pair of hydrophones are cross-correlated, and an estimate of the time delay is given by the time lag that maximizes the cross correlation function. Often the time-delay estimates are corrupted by the presence of noise. By replacing each of the omnidirectional hydrophones with an array of hydrophones, and then cross-correlating the beamformed outputs of the arrays, the author shows that the effect of noise on the time-delay estimation process is reduced greatly. Both conventional and adaptive beamforming methods are implemented in the frequency domain and the advantages of array beamforming (prior to cross-correlation) are highlighted using both simulated and real noise-field data. Further improvement in the performance of the broadband cross-correlation processor occurs when various prefiltering algorithms are invoked 相似文献
19.
Spatial processing, including beamforming and diversity combining, is widely used in communications to mitigate intersymbol interference (ISI) and signal fading caused by multipath propagation. Beamforming suppresses ISI (and noise) by eliminating multipath (and noise) arrivals outside the signal beam. Beamforming requires the signals to be highly coherent between the receivers. Diversity combining combats ISI as well as signal fading by taking advantage of the independent information in the signal. Classical (spatial) diversity requires that signals are independently fading, hence are (spatially) uncorrelated with each other. In the real world, the received signals are neither totally coherent nor totally uncorrelated. The available diversity is complex and not well understood. In this paper, we study the spatial processing gain (SPG) as a function of the number of receivers used, receiver separation, and array aperture based on experimental data, using beamforming and multichannel combining algorithms. We find that the output symbol signal-to-noise ratio (SNR) for a multichannel equalizer is predominantly determined by the array aperture divided by the signal coherence length, with a negligible dependence on the number of receivers used. For a given number of receivers, an optimal output symbol SNR (OSNR) is achieved by spacing the receivers equal to or greater than the signal coherence length. We model the SPG in decibels as the sum of the noise suppression gain (NSG, equivalent to signal-to-noise enhancement) and the ISI suppression gain (ISG, equivalent to signal-to-ISI enhancement) both expressed in decibels; the latter exploits the spatial diversity and forms the basis for the diversity gain. Data are interpreted using the modeled result as a guide. We discuss a beam-domain processor for sonar arrays, which yields an improved performance at low-input SNR compared to the element-domain processor because of the SNR enhancement from beamforming many sensors. 相似文献
20.
The problem of beam formation from a towed line array whose shape has been distorted is considered. Emphasis is placed on the beam broadening and range estimation effects of array shape perturbations and how the resulting losses can be regained if the actual element positions are known. Specific illustrations are provided for various levels of shape distortion. For example, a 15-m bow in a 232.5-m-long array broadens the beamwidth by a factor of 3 at 50 Hz. As another example, a 6-m bow in an 800-m-long array leads to a 20-pereent range underestimation at 10 km for a 100-500-Hz broadband source. 相似文献