共查询到20条相似文献，搜索用时 609 毫秒
1.
The hydraulic conductivity represents an important indicator parameter in the generation and redistribution of excess pore pressure of sand–silt mixture soil deposits during earthquakes. This paper aims to determine the relationship between the undrained shear strength (liquefaction resistance) and the saturated hydraulic conductivity of the sand–silt mixtures and how much they are affected by the percentage of low plastic fines (finer than 0.074 mm) and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests carried out on samples reconstituted from Chlef river sand with 0, 10, 20, 30, 40, and 50 % non-plastic silt at an effective confining pressure of 100 kPa and two initial relative densities (D r = 20, 91 %) are presented and discussed. It was found that the undrained shear strength (liquefaction resistance) can be correlated to the fines content, intergranular void ratio and saturated hydraulic conductivity. The results obtained from this study reveal that the saturated hydraulic conductivity (k sat) of the sand mixed with 50 % low plastic fines can be, in average, four orders of magnitude smaller than that of the clean sand. The results show also that the global void ratio could not be used as a pertinent parameter to explain the undrained shear strength and saturated hydraulic conductivity response of the sand–silt mixtures. 相似文献
2.
Leila Hazout Zein El-Abidine Zitouni Mostefa Belkhatir Tom Schanz 《Geotechnical and Geological Engineering》2017,35(5):2079-2105
Liquefaction of soils is a natural phenomenon associated with a dramatic loss of the soil shear strength in undrained conditions due to a development of excess pore water pressure. It usually causes extensive damages to buildings and infrastructures during earthquakes. Thus, it is important to evaluate extent of influential parameters on the liquefaction phenomenon of soils in order to clearly understand the different mechanisms leading to its triggering. The soil gradation is one of the most important parameters affecting the liquefaction phenomenon. In this context, a series of undrained compression triaxial tests were carried out on eighteen natural loose (Dr = 25%) sandy samples containing low plastic fines content of 2% (Ip = 5%) considering different extreme sizes (1.6 mm ≤ Dmax ≤ 4 mm and 0.001 mm ≤ Dmin ≤ 0.63 mm) and two mean grain size ranges (0.25 mm ≤ D50 ≤ 1.0 mm) and (1.0 mm ≤ D50 ≤ 2.5 mm). The initial confining pressure for all tests was kept constant (P′c = 100 kPa). The obtained test results indicate that the mean grain size (D50) and extreme grain sizes (Dmax and Dmin) have a significant influence on the undrained shear strength (known as liquefaction resistance) and appear as pertinent factors for the prediction of the undrained shear strength for the soil gradation under study. The undrained shear strength and the excess pore water pressure can be correlated to the extreme grain sizes (Dmax and Dmin) and the mean grain size (D50) of tested wet deposited samples. 相似文献
3.
Shear strength and pore-water pressure characteristics of sandy soil mixed with plastic fine 总被引：1，自引：0，他引：1
Recent earthquake case histories have revealed the liquefaction of mixtures of sand and fine particles during earthquakes. Different from earlier studies which placed an emphasis on characterisation of liquefaction in terms of the induced shear stress required to cause liquefaction, this study adopted a strain approach because excess pore-water pressure generation is controlled mainly by the level of induced shear strains. The current study includes the results of a set of laboratory tests carried out on sand specimens with the same relative densities and variation in the plastic fines (kaolinite or bentonite) contents ranging from 0 to either 30 % and consolidated at mean confining pressure of 100, 200 and 300 kPa using static triaxial test apparatus, in order to study the influence of fine content and other parameters on the undrained shear strength and liquefaction potential of clayey sand specimens; also, pore-water pressures in the specimens are discussed. Results of tests show that the peak strength decreases as the fines (kaolinite or bentonite) content increases up to a threshold content of fines (FCth) after which, increases in plastic fine content lead to improve the peak shear strength of specimens, and also the ultimate steady-state strength has been improved due to the increased in plastic fines content. Also, pore pressure build-up in clayey sands is generally slower than that observed in pure sand. 相似文献
4.
During the last mid-century, the Chlef area was strongly affected by two earthquakes. From the geological context, there were numerous ejections onto the ground level of great masses of sandy soils and large displacements of various forms of some building foundations. These damages are due to soil liquefaction problem. This loss of shear strength can be attributed to many factors. History of recent cases indicates that sand deposited with silt content is much more liquefiable than clean sand. Therefore, a deep understanding of silty sand behavior is needed for the liquefaction assessment of silty sandy soils. Moreover, during seismic shaking, the post-liquefaction behavior of silty sand and, consequently, the stability of structures founded on liquefied soil depend on the steady-state shear strength of soil. The objective of this laboratory investigation is to show the effect of silt contents and the relative density on the mechanical behavior of such soils in monotonic loading. In this context, a series of undrained triaxial tests were performed on reconstituted saturated silty sand samples with different fines content ranging from 0% to 40%. In all tests, the confining pressure was held constant to 100 kPa. The fines content and the global void ratio are expressed by means of the equivalent void ratio. Linear correlations relating the undrained residual shear strength of loose, medium dense, and dense (D r?=?12%, 50%, and 90% before consolidation) sand–silt mixtures to the equivalent void ratio are obtained. The concept of the equivalent void ratio will then be used as a key parameter to express the dilatancy behavior of both clean and silty sand soils. Moreover, from the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not represent the actual behavior of the soil as well. 相似文献
5.
Hanifi Missoum Mostefa Belkhatir Karim Bendani Mustapha Maliki 《Geotechnical and Geological Engineering》2013,31(1):279-296
In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results. 相似文献
6.
Effect of grading characteristics on the undrained shear strength of sand: review with new evidences
In this paper, the shear strength of saturated pure sand and sand–silt mixture is evaluated by monotonic undrained triaxial tests that were carried out on reconstituted specimens at same relative densities and a constant confining pressure (σ 3?=?300 kPa). The test results were used to conclude on the effect of low non-plastic contents (0–20 %) and grading characteristics on the liquefaction resistance of the sand. The test results indicate that the undrained residual strength reduced with the increase of non-plastic fine content. Also, shear strength of gap-graded sand mixed with low non-plastic fine content increases with decrease in effective size (D 50). In other words, in this state, we can use the D 50 as a parameter to control of silty sand’s undrained resistance. Besides, the undrained residual strength of pure sand specimens with same effective size increases due to increase of coefficient of uniformity (C u). 相似文献
7.
Wen-Jong Chang Sheng-Huoo Ni An-Bin Huang Yan-Hong Huang Yu-Zhang Yang 《Engineering Geology》2011,(3):235
Geotechnical reconnaissance of a recurrent liquefaction site at a Quaternary alluvial deposit in southern Taiwan was conducted to establish a comprehensive case history for liquefaction on silty fine sand with high fines content. The liquefaction occurred at a silty fine sand layer with D50 = 0.09 mm and fines content greater than 35% and was triggered by a Mw = 6.4 earthquake on March 4, 2010, which induced maximum horizontal acceleration up to 0.189 g at the site. In situ subsurface characterizations, including standard penetration test, cone penetration test, and shear wave velocity measurement, were performed as well as cyclic simple shear tests on undisturbed specimens retrieved by a modified hydraulic piston sampler. Comparisons of cyclic resistance ratios (CRRs) indicate that CPT sounding with standard penetration rate could overestimate the resistance ratio and drainage conditions during penetration should be considered for high fines content soil in the liquefaction analysis. Additionally, variations of CRRs from different in situ tests indicate that correlations among in situ tests and CRR could be soil specific and precautions should be taken when using these curves on silty fine sands. 相似文献
8.
Wiam Khebizi Sidali Denine Jean Canou Jean-Claude Dupla 《Geomechanics and Geoengineering》2019,14(1):30-40
Soil improvement using fibres is widely used in soil stabilisation to prevent sand liquefaction. In order to study the undrained behaviour and liquefaction resistance of sand reinforced with polypropylene fibres, a series of triaxial compressive tests were conducted on unreinforced and reinforced Chlef sand with different contents of polypropylene fibres (0, 0.3, 0.5 and 0.8%). Samples were prepared at 30% and 80% relative densities representing loose and dense states respectively, and triaxial tests were performed at confining pressures of 50, 100 and 200 kPa. Tests results show that fibre inclusion has a significant effect on the shear strength and dilation of sandy soil. The increase in strength is function of fibre content, relative density and confining pressure. The maximum strength improvement for both loose and dense fibre-reinforced sand is more pronounced at higher confining pressure and at higher fibre content. 相似文献
9.
南京砂强度特征与静态液化现象分析 总被引：2，自引：1，他引：1
在松散、中密和密实状态下,以南京粉细砂三轴固结不排水试验结果为基础,进行了强度、变形与静态液化特征的分析。松散南京砂强度特性表现出典型的应变软化,当轴向变形小于1 %时强度达到最大值,而后急剧降低;在50,100 kPa围压时发生了静态液化。但随着固结压力的增大,静态液化消失。与南京砂具有相同土骨架的松散纯净砂却在低围压下未出现静态液化,其形成机制是：粉粒的存在未使土体孔隙比发生较大变化,却引起更大的体缩性;中密和密实南京粉细砂表现出加工硬化的强度特征,临界应力状态线倾角高达55°,具有较高的抗静态液化能力。 相似文献
10.
Abouzar Sadrekarimi 《Geotechnical and Geological Engineering》2016,34(4):1135-1154
Static liquefaction failure of a sloping ground occurs when the shear stress applied by a monotonic triggering load exceeds the undrained yield (peak) shear strength of the saturated liquefiable cohesionless soil. Current practices for determining the in-situ undrained yield strength for ground subject to static shear stress either rely on a suite of costly laboratory tests on undisturbed field samples or empirical correlations based on in-situ penetration tests which do not account for the effects of anisotropic consolidation, intermediate principal stress, and mode of shear on the degree of strain-softening and brittleness of cohesionless soils. This study investigates the effects of variations in the direction and relative magnitudes of principal stresses associated with different modes of shear and ground slopes on static liquefaction failure of cohesionless soils. Empirical relationships are developed between soil brittleness index and maximum excess pore water pressure ratio to characterize soil shearing behavior observed in a database of 271 undrained laboratory shear tests collected from the past literature. The application of these relationships for estimating the static liquefaction triggering strength of cohesionless soils under sloping grounds is described for plane-strain boundary conditions and the results are compared with those back-calculated for several cases of static liquefaction flow failures. The proposed procedure incorporates variations in mode of shear and initial stress anisotropy in an empirical formulation based on in-situ penetration tests. 相似文献
11.
The influence of static shear stress on undrained cyclic behavior of nonplastic and low-plasticity silts has been studied
by means of undrained cyclic torque-controlled ring-shear tests. The cyclic and post-cyclic behavior of silty soils assumed
on sliding surface were investigated to assess the liquefaction potential and cyclically induced deformation of silty slopes.
Six different initial static shear stresses corresponding to slope angles from 0° to 25° were examined. To better understand
undrained cyclic behavior of silt governed by a change in clay content, three different mixtures were achieved by mixing of
nonplastic silt with 0%, 10%, and 20% of commercially available clay. These tests were conducted to simulate field conditions
prior to earthquake with initial static shear stresses corresponding to slopes and those with no initial static shear stresses
of level grounds. The gradual loss of mobilized undrained cyclic shear resistance after failure and pore water buildup in
relation to a number of cycles was observed. The undrained response of the soil to cyclic shear stress loading with the constant
amplitude revealed the significant effect of the initial static shear stress on the excess pore water pressure generation
and post-failure shear resistance. Test results showed that an increase in the initial static shear stress at the given initial
effective normal stress is associated with an increase of mobilized shear resistance at its peak state; however, the actual
resistance to liquefaction diminished for both nonplastic and low-plasticity silts. During both cyclic and post-cyclic stages
of loading, distinctly different types of shear deformation were identified. In order to evaluate mobility of landslides,
a modified conventional brittleness index for seismic loading, , was proposed and used to characterize unlimited deformation of silts. 相似文献
12.
饱和土体静态液化失稳理论预测 总被引：1，自引：0，他引：1
通过在屈服准则和剪胀性方程中引入材料状态参数,建立了一个与材料状态相关的本构模型,用于模拟不同初始孔隙比和围压下土体的应力-应变关系。基于二阶功理论,建立了饱和土体静态液化失稳理论判别准则。通过预测一系列饱和松砂三轴不排水试验结果,验证了所建立的本构模型及判别预测准则的合理性。分析结果表明,静态液化发生于土体硬化阶段,静态液化触发伴随着剪应力达到峰值,其后剪应力降低且孔隙水压力持续增长。进一步地,模拟了充分降解的城市固体废弃物在不排水条件下的应力-应变特性,并预测到了潜在失稳线及静态液化触发点。 相似文献
13.
A solution is developed for the build‐up, steady and post‐arrest dissipative pore fluid pressure fields that develop around a blunt penetrometer that self‐embeds from freefall into the seabed. Arrest from freefall considers deceleration under undrained conditions in a purely cohesive soil, with constant shear strength with depth. The resulting decelerating velocity field is controlled by soil strength, geometric bearing capacity factors, and inertial components. At low impact velocities the embedment process is controlled by soil strength, and at high velocities by inertia. With the deceleration defined, a solution is evaluated for a point normal dislocation penetrating in a poroelastic medium with a prescribed decelerating velocity. Dynamic steady pressures, PD, develop relative to the penetrating tip geometry with their distribution conditioned by the non‐dimensional penetration rate, UD, incorporating impacting penetration rate, consolidation coefficient and penetrometer radius, and the non‐dimensional strength, ND, additionally incorporating undrained shear strength of the sediment. Pore pressures develop to a steady peak magnitude at the penetrometer tip, and drop as PD=1/xD with distance xD behind the tip and along the shaft. Peak induced pressure magnitudes may be correlated with sediment permeabilities, post‐arrest dissipation rates may be correlated with consolidation coefficients, and depths of penetration may be correlated with shear strengths. Together, these records enable strength and transport parameters to be recovered from lance penetrometer data. Penetrometer data recorded off La Palma in the Canary Islands (J. Volcanol. Geotherm. Res. 2000; 101 :253) are used to recover permeabilities and consolidation coefficients from peak pressure and dissipation response, respectively. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
14.
《Geomechanics and Geoengineering》2013,8(1):47-58
The effect of non-plastic fines (silt) on the undrained monotonic response of saturated and isotropically consolidated sand specimens prepared to various measures of their density was studied in detail through various approaches namely gross void ratio approach, relative density approach, sand skeleton void ratio approach, and interfine void ratio approach. Specimens of 50 mm in diameter and 100 mm in height were tested at a rate of loading of 0.6 mm/min for this purpose. The limiting silt content and the relative density of a specimen were found to influence the undrained monotonic response of sand–silt mixtures to a great extent. Undrained monotonic response was observed to be independent of silt content at very high relative densities; however the presence of fines significantly influenced this response of loose to medium dense specimens. Individual and combined analyses of undrained monotonic peak strengths which are closely related to the liquefaction related problems have been done in this paper to assess the variation patterns. 相似文献
15.
Ahmed Djafar Henni Ahmed Arab Mostefa Belkhatir A. Saaed Hamoudi Hamid Khelafi 《Arabian Journal of Geosciences》2013,6(2):297-307
This experimental study deals with the effect of the overconsolidation ratio on the monotonic undrained shear behavior of silty sand. The study is based on the undrained monotonic triaxial tests for the overconsolidation ratios (OCR?=?1, 2, 4, and 8), with different silt contents ranging from 0% to 40%. The laboratory tests were carried out at an initial relative density of Dr?=?50%. The paper is composed of two parts. The first one presents the tested soils; the second one gives an analysis of the test results and discusses the influence of the overconsolidation ratio on the shear strength of the soil. The test results indicate that the shear strength of the soil increases with the increase of the overconsolidation ratio resulting in an increase of soil dilatancy. The increase in the amount of fines from 0% to 40% increases the phase of the contractancy and consequently reducing the phase of dilatancy of the tested material 相似文献
16.
Mahmoudi Youcef Cherif Taiba Abdellah Hazout Leila Belkhatir Mostefa 《Acta Geotechnica》2022,17(8):3269-3292
The published literature has revealed conflicting results regarding the effect of low plastic fines fraction (Ip?≤?5.0%) on the mechanical behavior of sandy soils. For this reason, the use of different sample initial structures as (initial relative density approach, global void ratio index approach, etc.) could explain these different mechanical responses of granular materials. Thus, it is necessary to evaluate the quantitative aspect of the low plastic fines effects on the undrained monotonic response of sand-silt mixtures using the global void ratio approach. To achieve this goal, an experimental testing program through controlled monotonic triaxial tests was carried out on reconstituted saturated Chlef sand containing from 0 to 50% silt with an interval of 10% at three global void ratios (e?=?0.64, 0.66 and 0.68) and subjected to constant confining pressure (σ'3?=?100 kPa). The different samples were reconstituted using two different preparation techniques: DFP and MT. The obtained results show that the low plastic fines content appears as a very relevant parameter in the characterization of the mechanical response of sand-silt mixture samples reconstituted at constant global void ratios, where the steady state shear strength and instability shear strength decreased with the increase in low plastic fines content up to the limiting fines contents (Fc?=?40% and Fc?=?10%) considering both studied initial structures (Dry funnel pluviation and Moist tamping), respectively. Beyond these thresholds fines contents, a reverse trend was observed for all parameters under study. Moreover, the test results indicate that the brittleness index, flow potential (Vf), friction index, equivalent void ratio (e*) and equivalent relative density (Dr*) could be considered as reliable parameters in the prediction of the mechanical behavior of the silty sand soils under study.
相似文献17.
Owing to imperfect boundary conditions in laboratory soil tests and the possibility of water diffusion inside the soil specimen in undrained tests, the assumption of uniform stress/strain over the sample is not valid. This study presents a qualitative assessment of the effects of non‐uniformities in stresses and strains, as well as effects of water diffusion within the soil sample on the global results of undrained cyclic simple shear tests. The possible implications of those phenomena on the results of liquefaction strength assessment are also discussed. A state‐of‐the‐art finite element code for transient analysis of multi‐phase systems is used to compare results of the so‐called ‘element tests’ (numerical constitutive experiments assuming uniform stress/strain/pore pressure distribution throughout the sample) with results of actual simulations of undrained cyclic simple shear tests using a finite element mesh and realistic boundary conditions. The finite element simulations are performed under various conditions, covering the entire range of practical situations: (1) perfectly drained soil specimen with constant volume, (2) perfectly undrained specimen, and (3) undrained test with possibility of water diffusion within the sample. The results presented here are restricted to strain‐driven tests performed for a loose uniform fine sand with relative density Dr=40%. Effects of system compliance in undrained laboratory simple shear tests are not investigated here. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
18.
Hussain Rojimul Ghosh Kishor Kumar Garg Ankit Ravi K. 《Geotechnical and Geological Engineering》2021,39(2):1117-1131
Biochar is a carbon-rich and low microbial degrading material obtained after pyrolysis of biomass in the absence or limited content of oxygen. The impact of biochar on hydraulic properties of soil is extensively studied in agricultural and geotechnical or geoenvironmental engineering for potential application in bioengineered structures. While a little study is conducted to assess its effect on soil mechanical properties, especially shear strength. However, the effect of biochar on the combined shear strength and compaction characteristics of soil is not studied. The shear strength of biochar amended soil is thought to be related to the compaction characteristics. In addition, the effect of biochar on the shear strength of the soil is soil and biochar specific. In this study, an attempt was made to investigate and better understand the effect of biochar on the shear strength and compaction characteristics of a clayey sand for potential application in bioengineered structures. Standard proctor, direct shear and unconfined compression tests were conducted on bare soil and soil amended with 5, 10 and 15% (w/w) biochar. The experimental results revealed that the amendment of biochar from 5 to 15% (w/w) decreased the dry density and increased the shear strength parameters such as cohesion (c) and angle of internal friction (ϕ) of the soil. While it decreased the undrained shear strength (cu) at higher compaction density (> 0.95MDD) and increased at lower compaction density (< 0.9MDD). Thus, in undrained condition, the initial compaction density has a strong influence on the shear strength of biochar amended soil. In addition, the increased c and ϕ and decreased dry density in biochar amended soil is observed to increase the stability of slopes (hypothetical). The increase of c and ϕ is believed to be due to the roughness and active chemicals (functional groups) present on the surface of the biochar. The decreased cu at higher density is believed to be due to the lubricating effect by the higher water content.
相似文献19.
A consistent methodology based on the critical state framework to characterize the different regimes of fine-grained soil behavior under earthquake loads is put forward. Shear strength and deformation behavior of soils depend in a major way on the combination of volume and confining stress. Depending on their combination, a soil aggregate may fracture into clastic debris, fail with fault planes, or yield plastically. This characterization of the class of limiting soil behavior is used to analyze the potential for large deformation and liquefaction in fine grained soils. The central piece of the proposed characterization is the (η, LI5) stability diagram where η = q/p′ and LI5 = LI + 0.5 log (p′/5). This diagram captures the effects of soil plasticity through liquidity index LI, confinement through mean normal effective stress p′, and shear stress q through the stress ratio η. The three regions of behavior; fracture, fault, and fold/yield are identified. Soils become susceptible to liquefaction when they shift into the fracture zone (LI5 ≤ 0.4), or if they plot outside of the stable yielding region.Under earthquake loading, the initial soil states will migrate into different regions in the stability diagram depending on their initial location, shear stress increment, and, pore pressure response. The final position of the soil state would dictate the type of limiting behavior expected in the field; fracture, rupture or yield. The final states which fall into the fracture region have the potential for catastrophic failures including “liquefaction”; the ones which fall onto the rupture region would experience the attainment of a peak stress ratio followed by softening along failure planes; the ones in the yield region would continue to yield in a stable manner. The latter two types of deformations while resulting in large deformation may not be of a catastrophic nature. The proposed characterization is used to examine the liquefaction susceptibility of fine grained soils from China, Taiwan, and Turkey. Use of simplified empirical criteria based on parameters such as plasticity index and fines contents may not capture the true nature of the type of undrained limiting behavior of fine grains soils in the field including liquefaction. 相似文献
20.
在探讨含细粒砂土内部结构和粒间相互作用的基础上,引入粒间状态变量概念,对含细粒砂土力学性状随细粒含量的变化进行了预测分析:当Drs >>0时含细粒砂土类似于e=ec时均质砂的不排水性状,具有较高的强度;当Drs→0时含细粒砂土最终性状具有不确定性;当Drs < 0时含细粒砂土表现为剪缩性状。将南京砂中粗粒和细粒进行重新配制获得含不同细粒的砂土,对它们进行不排水剪试验;在利用粒间状态变量对试验结果进行分析的基础上,将试验结果与预测分析进行比对,两者的吻合性较高。在ec-logSus空间内稳态线随粉粒的增加而向上移动,且各稳态线间呈平行状。因此,粒间状态变量能较好地反映无黏性土力链的变化,是描述砂土微观结构的新途径。 相似文献